Search NASA⌕ Search

SEARCH · Search NASA

Results for “density maps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Deposition Velocities of Non-Newtonian Slurries in Pipelines: Complex Simulant Testing

One of the concerns expressed by the External Flowsheet Review Team (EFRT) is about the potential for pipe plugging at the Waste Treatment and Immobilization Plant (WTP). Per the review’s executive summary, “Piping that transports slurries will plug unless it is properly designed to minimize this risk. This design approach has not been followed consistently, which will lead to frequent shutdowns due to line plugging.” To evaluate the potential for plugging, deposition-velocity tests were performed on several physical simulants to determine whether the design approach is conservative. Deposition velocity is defined as the velocity below which particles begin to deposit to form a moving bed of particles on the bottom of a straight horizontal pipe during slurry-transport operations. The deposition velocity depends on the system geometry and the physical properties of the particles and fluid. An experimental program was implemented to test the stability-map concepts presented in WTP-RPT-175 Rev. 01. Two types of simulant were tested. The first type of simulant was similar to the glass-bead simulants discussed in WTP-RPT-175 Rev. 0 ; it consists of glass beads with a nominal particle size of 150 µm in a kaolin/water slurry. The initial simulant was prepared at a target yield stress of approximately 30 Pa. The yield stress was then reduced, stepwise, via dilution or rheological modifiers, ultimately to a level of <1 Pa. At each yield-stress step, deposition-velocity testing was performed. Testing over this range of yield-stress bounds the expected rheological operating window of the WTP and allows the results to be compared to stability-map predictions for this system. The second simulant was a precipitated hydroxide that simulates HLW pretreated sludge from Hanford waste tank AZ-101. Testing was performed in a manner similar to that for the first simulant over a wide range of yield stresses; however, an additional test of net-positive suction-head required (NPSHR) was performed at each yield stress condition. Unlike the previous simulant, the sizes and densities of the particles that can deposit in the piping are a result of the simulant precipitation process; there is expected to be a complex mixture of particles of various sizes and densities that make it difficult to predict a stability map. The objective of the testing is to observe whether behavior consistent with the stability-map concept occurs in complex simulants with mixtures of different sizes and densities.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Exact solitary solution of Schamel equation in plasmas with negative ions

A theoretical investigation is carried out for understanding the properties of the solitary solution in plasmas with negative ions. Schamel equation for a plasma consisting of electron, positive ions and negative ions has been derived by using the reductive perturbation method. The effects of negative ions and the density on the properties of the solitary solution is discussed. We make use of the extended mapping method and auxiliary equation to obtain the solution of Schamel equation. This solution includes the Jacobi elliptic function solutions, hyperbolic function solutions, rational solutions, and periodic wave solutions. Furthermore, we show that the incorporate negative ion effects in the nonlinear propagation of ion acoustic waves that are controlled by trapped electrons and the results of the solitary solution in plasmas with negative ions model are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Integrated Decision Methodology for Final Disposal of Radioactive Sources

Radioactive sources are used throughout the world, and their beneficial uses are many. Sources are at the core of many applications in different branches of industry, medicine, agriculture and research. Sources are present in a very wide range of equipment that is used for, inter alia, cancer treatment, killing bacteria in food, sterilizing medical supplies, measuring instruments such as gauges used to measure soil moisture and soil density and many other components, irradiating seeds for enhancing food production, protecting buildings from lightning strikes, mapping underground sources of water, prospecting for oil and gas reserves, measuring density of soil for construction projects, or even detecting smoke. At their “cradle” and when in use, radioactive sources are usually properly managed and controlled. It is when a source has reached the end of its useful life when they are at a higher risk of being under inadequate control, poorly managed, or even becoming orphan. Sources that have reached the end of their useful life must be carefully and safely managed. The “grave” of disused sources needs a proper disposal process to prevent them from posing a potential threat to people or the environment. To protect the public and the environment from the potential hazards of ionizing radiation, and to prevent disused sources from becoming orphan, a “cradle-to-grave” control of radioactive sources is essential, as promoted by the Code of Conduct on the Safety and Security of Radioactive Sources. This approach requires a national policy and strategy, an adequate legal and regulatory framework, and adequate resources and infrastructure. Many IAEAMember States have expressed the need for effective solutions to this challenge. There is also a gap related to the life cycle costs of potential disposal practices. This paper proposes a multi-attribute decision making methodology to compare disposal options using both economic and non-economic criteria leading to a preferred option for disposal and a strategy for final disposal of disused radioactive sources that is specific and optimized for each IAEA Member State.

Beatty, Randy↗

The effects of digital elevation model resolution on the calculation and predictions of topographic wetness indices.

One of the largest exports in the Southeast U.S. is forest products. Interest in biofuels using forest biomass has increased recently, leading to more research into better forest management BMPs. The USDA Forest Service, along with the Oak Ridge National Laboratory, University of Georgia and Oregon State University are researching the impacts of intensive forest management for biofuels on water quality and quantity at the Savannah River Site in South Carolina. Surface runoff of saturated areas, transporting excess nutrients and contaminants, is a potential water quality issue under investigation. Detailed maps of variable source areas and soil characteristics would therefore be helpful prior to treatment. The availability of remotely sensed and computed digital elevation models (DEMs) and spatial analysis tools make it easy to calculate terrain attributes. These terrain attributes can be used in models to predict saturated areas or other attributes in the landscape. With laser altimetry, an area can be flown to produce very high resolution data, and the resulting data can be resampled into any resolution of DEM desired. Additionally, there exist many maps that are in various resolutions of DEM, such as those acquired from the U.S. Geological Survey. Problems arise when using maps derived from different resolution DEMs. For example, saturated areas can be under or overestimated depending on the resolution used. The purpose of this study was to examine the effects of DEM resolution on the calculation of topographic wetness indices used to predict variable source areas of saturation, and to find the best resolutions to produce prediction maps of soil attributes like nitrogen, carbon, bulk density and soil texture for low-relief, humid-temperate forested hillslopes. Topographic wetness indices were calculated based on the derived terrain attributes, slope and specific catchment area, from five different DEM resolutions. The DEMs were resampled from LiDAR, which is a laser altimetry remote sensing method, obtained from the USDA Forest Service at Savannah River Site. The specific DEM resolutions were chosen because they are common grid cell sizes (10m, 30m, and 50m) used in mapping for management applications and in research. The finer resolutions (2m and 5m) were chosen for the purpose of determining how finer resolutions performed compared with coarser resolutions at predicting wetness and related soil attributes. The wetness indices were compared across DEMs and with each other in terms of quantile and distribution differences, then in terms of how well they each correlated with measured soil attributes. Spatial and non-spatial analyses were performed, and predictions using regression and geostatistics were examined for efficacy relative to each DEM resolution. Trends in the raw data and analysis results were also revealed.

09 BIOMASS FUELS↗

INFERRING GRAVITATIONAL POTENTIALS FROM MASS DENSITIES IN CLUSTER-SIZED HALOS

We use N-body simulations to quantify how the escape velocity in cluster-sized halos maps to the gravitational potential in a ΛCDM universe. Using spherical density-potential pairs and the Poisson equation, we find that the matter density inferred gravitational potential profile predicts the escape velocity profile to within a few percent accuracy for group and cluster-sized halos (10{sup 13}<M{sub 200}<10{sup 15} M {sub ⊙}, with respect to the critical density). The accuracy holds from just outside the core to beyond the virial radius. We show the importance of explicitly incorporating a cosmological constant when inferring the potential from the Poisson equation. We consider three density models and find that the Einasto and Gamma profiles provide a better joint estimate of the density and potential profiles than the Navarro, Frenk, and White profile, which fails to accurately represent the escape velocity. For individual halos, the 1σ scatter between the measured escape velocity and the density-inferred potential profile is small (<5%). Finally, while the sub-halos show 15% biases in their representation of the particle velocity dispersion profile, the sub-halo escape velocity profile matches the dark matter escape velocity profile to high accuracy with no evidence of velocity bias outside 0.4r {sub 200}.

79 ASTRONOMY AND ASTROPHYSICS↗

Analysis and application of ERTS-1 data for regional geological mapping

Combined visual and digital techniques of analysing ERTS-1 data for geologic information have been tried on selected areas in Pennsylvania. The major physiolographic and structural provinces show up well. Supervised mapping, following the imaged expression of known geologic features on ERTS band 5 enlargements (1:250,000) of parts of eastern Pennsylvania, delimited the Diabase Sills and the Precambrian rocks of the Reading Prong with remarkable accuracy. From unsupervised mapping, transgressive linear features are apparent in unexpected density, and exhibit strong control over river valley and stream channel directions. They are unaffected by bedrock type, age, or primary structural boundaries, which suggests they are either rejuvenated basement joint directions on different scales, or they are a recently impressed structure possibly associated with a drifting North American plate. With ground mapping and underflight data, 6 scales of linear features have been recognized.

Gold, D. P.↗

Auroral kilometric radiation/aurora correlation

Auroral kilometric radiation (AKR) observations from the ISIS 1 topside sounder receiver were compared with visual auroral observations from the network of Alaskan all-sky camera stations. The goal was to relate AKR source region encounters to specific auroral forms on the same magnetic field line. Thirty-eight simultaneous data sets were identified and analyzed. In general, intense AKR was associated with bright auroral arcs and conditions of weak or no AKR corresponded to times when either no aurora or only a faint arc or weak diffuse aurora were observed. Five cases, when both intense AKR and bright visual aurora were present, were analyzed in detail. Complete electron density N sub e contours, from the satellite altitude down to the F region ionization peak, were obtained along N-S traversals of the AKR source region. In addition, the ISIS 1 orbital tracks were projected down the magnetic field lines to the auroral altitude and compared to auroral features on a map derived from the all sky camera images. Density cavities (regions where N sub e 100/cu cm) were encountered on each of these passes.

Benson, R. F.↗

Auroral kilometric radiation/aurora correlation

Auroral kilometric radiation (AKR) observations from the ISIS 1 topside sounder receiver were compared with visual auroral observations from the network of Alaskan all-sky camera stations. The goal was to relate AKR source region encounters to specific auroral forms on the same magnetic field line. Thirty-eight simultaneous data sets were identified and analyzed. In general, intense AKR was associated with bright auroral arcs and conditions of weak or no AKR corresponded to times when either no aurora or only a faint arc or weak diffuse aurora were observed. Five cases, when both intense AKR and bright visual aurora were present, were analyzed in detail. Complete electron density N sub e contours, from the satellite altitude down to the F region ionization peak, were obtained along N-S traversals of the AKR source region. In addition, the ISIS 1 orbital tracks were projected down the magnetic field lines to the auroral altitude and compared to auroral features on a map derived from the all sky camera images. Density cavities (regions where N sub e 100/cu cm) were encountered on each of these passes. Previously announced in STAR as N83-27516

Benson, R. F.↗

Detection of an electron beam in a high density plasma via an electrostatic probe

An electron beam is detected by a 1D floating potential probe array in a relatively high density (10e12 - 10e13 cm-3) and low temperature (~ 5 eV) plasma of the Magnetic Reconnection Experiment (MRX). Clear perturbations in the floating potential profile by the electron beam are observed. Based on the floating potential profile and a current balance equation to the probe array tips, the effective width of the electron beam is determined, from which we determine the radial and toroidal beam current density profiles. After the profile of the electron beam is specified from the measured beam current, we demonstrate the consistency of the current balance equation and the location of the perturbation is also in agreement with field line mapping. No significant broadening of the electron beam is observed after the beam propagates for tens of centimeters through the high density plasma. These results prove that the field line mapping is, in principle, possible in high density plasmas.

field line mapping↗

Experimental Research on Selective Laser Melting AlSi10Mg Alloys: Process, Densification and Performance

In this work, a set of experiments was designed to investigate the effect of process parameters on the relative density of the AlSi10Mg parts manufactured by SLM. The influence of laser scan speed v, laser power P and hatch space H, which were considered as the dominant parameters, on the powder melting and densification behavior was also studied experimentally. In addition, the laser energy density was introduced to evaluate the combined effect of the above dominant parameters, so as to control the SLM process integrally. As a result, a high relative density (> 97%) was obtained by SLM at an optimized laser energy density of 3.5-5.5 J/mm{sup 2}. Moreover, a parameter–densification map was established to visually select the optimum process parameters for the SLM-processed AlSi10Mg parts with elevated density and required mechanical properties. The results provide an important experimental guidance for obtaining AlSi10Mg components with full density and gradient functional porosity by SLM.

36 MATERIALS SCIENCE↗

Dark Material in the Polar Layered Deposits on Mars

Viking infrared thermal mapping (IRTM) and bistatic radar data suggest that the bulk density of the erg material is much lower than that of the average Martian surface or of dark dunes at lower latitudes.

Martian surface dark dunes Mars↗

Sampling Density in Regional Exploration and Environmental Geochemical Studies: A Review

A variety of factors contribute to the proper and efficient evaluation of geochemical programs including sampling medium, sample size and sample fraction, sampling density, digestion procedure, and analytical techniques. Among the aforementioned factors, sampling density is of great importance, affecting project ability to detect anomalous sites, which are either economically viable or environmentally hazardous. It is quite critical to have a sufficient number of samples to delineate geochemical anomalies or baselines and to reveal the relative variations in elemental concentrations in a study area. The resolution of the subsequent maps obtained by sampling greatly depends on sampling density. While a large number of samples may generate redundant data, a small number of samples smooth out the patterns and may completely miss anomalies. This review provides a platform for applied geochemists who desire to design a sampling scheme for a regional geochemical program and do not have the financial resources to perform an orientation survey, which will give them the necessary information for designing, according to project objectives, a cost-effective regional geochemical survey for their study area. It is advisable to integrate during the desktop study all available information, such as geological, structural, geophysical, remote sensing data and topographical data by using different data fusion algorithms to arrive at a sampling density fit-for-purpose of the target area. This in turn facilitates an effective spatial positioning of sample locations. Quantitative analyses of the efficiency of different sampling densities for delineating geochemical patterns have not been well documented, warranting more attention and research.

58 GEOSCIENCES↗

Distributed temperature sensing inside a 19-rod bundle

The temperature field within a model of a sodium-cooled fast reactor fuel rod bundle was measured using Ø155 μm fiber optic distributed temperature sensors (DTS). The bundle consists of 19 electrically-heated rods Ø6.3 mm and 865 mm long. Working fluids were argon and air at atmospheric pressure and Reynolds numbers up to 300. A 20 m-long DTS was threaded through Ø1 mm capillaries wound around rods as wire-wraps. The sensor generated 173 measurements along each rod at 5 mm resolution for a total of 3300 data locations. A second DTS, 58 m long, was suspended between rods to provide 9300 fluid temperature measurements at 20 mm resolution. Such data density makes it possible to construct 3D maps of the temperature field that are beyond the reach of traditional sensors such as thermocouples. This is illustrated through a series of steady-state and transient tests. As a result, the work demonstrates the feasibility of mapping temperature within the close confines of a rod bundle at resolutions suitable for validation of computational fluid dynamics codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An overview of HR-EBSD techniques for mapping local stress and dislocations in crystalline materials at sub-micron resolution

High resolution electron backscatter diffraction (HR-EBSD) is a technique used to map elastic strain, crystallographic orientation and dislocation density in a scanning electron microscope. Here, this review covers the background and mathematics of this technique, contextualizing it within the broader landscape of EBSD techniques and other materials characterization methods. Several case studies are presented showing the application of HR-EBSD to the study of plasticity in metals, failure analysis in microelectronics and defect quantification in thin films. This is intended to be a comprehensive resource for researchers developing this technique as well as an introduction to those wishing to apply it.

Ruggles, Timothy J. [Sandia National Laboratories ↗

Dependence of the Electron Beam Energy and Types of Surface to Determine EBSD Indexing Reliability in Yttria-Stabilized Zirconia

Electron backscatter diffraction (EBSD) is a powerful technique for the surface microstructure analysis. EBSD analysis of cubic yttria-stabilized zirconia (YSZ) in two and three dimensions (2-D, 3-D) is demonstrated using sequential slicing from a focused ion beam (FIB) followed by EBSD mapping to represent 3-D reconstructed high density grain structure with random orientation. The statistics related to accuracy of EBSD band detection shows that probability of accurate grain orientation detection increased significantly when the electron beam energy is increased from 10 kV to 30 kV. As a result of better sampling with increased interaction volume, a disparity between local and average grain orientation angle also exhibited the dependence of the electron beam energy to determine the accuracy of grain orientation. To study the accuracy and quality of EBSD band detection as a function of surface roughness and over layer formation, rapid EBSD measurement tests are performed on (a) YSZ surfaces ion-polished at ion beam energies of 65 nA at 30 kV and 1 nA at 30 kV and (b) carbon coated versus uncoated YSZ surfaces. The EBSD results at both 10 kV and 30 kV electron beam energies indicate that EBSD band detection accuracy is negatively affected by surface roughness and amorphous over layer formation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Probing the Mechanism of Selective Phosphate Adsorption from Wastewater Using Aqueous and Synchrotron X-ray Characterization

Ion exchange shows promise for recovering phosphate from wastewater as value-added products, but requires high phosphate selectivity to compete with conventional treatment. Hybrid anion exchange (HAIX) resins, which contain non-selective basic functional groups and selective iron oxide nanoparticles (FeOnp), can effectively remove phosphate from wastewater. However, knowledge gaps remain regarding the mechanisms of phosphate selectivity and influence of competing ions, hindering needed efforts to model adsorption dynamics and design scalable adsorption processes for varying wastewaters. To address these gaps, we integrated aqueous-phase adsorption analysis with solid-phase, synchrotron-based X-ray characterization; this integration facilitated elucidation of the distribution and speciation of iron, phosphate, and competing anions on HAIX resins. We compared a quaternary ammonium-functionalized HAIX resin (SBA) to a tertiary amine version (WBA) to determine the role of functional groups. X-ray radiography revealed differences in FeOnp speciation (goethite vs. ferrihydrite) and distribution (peripheral vs. homogeneous) between the resins, resulting in varied phosphate affinity and intraparticle diffusion resistance. Using micro-X-ray fluorescence (μ-XRF) and micro-X-ray absorption near-edge structure (μ-XANES) spectroscopy, we identified differences in where and how phosphate binds across resin types and wastewaters. Across wastewater compositions, FeOnp sites in WBA contribute more to phosphate adsorption than in SBA, possibly due to variations in Fe distribution and speciation. Phosphate adsorption densities calculated from quantitative μ-XRF maps matched those from aqueous analysis, demonstrating the effectiveness of this integrated approach. Altogether, results demonstrate the use of synchrotron-based X-ray characterization for investigating adsorption mechanisms and advance HAIX as a phosphate recovery technology from complex wastewaters.

Nutrient recovery↗

Field-Coupled Water Splitting with Metal-Free Donor–Acceptor Covalent Organic-Framework Junctions

Advancing metal-free electrocatalysts for hydrogen and oxygen evolution reactions (HER/OER) across acidic and alkaline media requires coordinated control of intermediate binding thermodynamics, interfacial charge delivery, and near-electrode transport dynamics. Here, we design amide-linked benzene–triazine covalent organic frameworks (BTA/TzTA-Hz COFs) and integrate them with carbon nanotubes (CNTs) to form COF–CNT junctions that establish a built-in interfacial electric field. Density functional theory (DFT) and electrostatic potential maps indicate complementary active motifs, with benzene-proximal fragments associated with HER and triazine-proximal motifs associated with OER. CNT integration shifts the contact-potential difference by ≈0.20 V, while operando electrochemical impedance spectroscopy suggests partially separable high-frequency junction-charging and lower-frequency Faradaic/transport responses. A 300 mT static magnetic field lowers the HER and OER overpotentials by tens of millivolts. Under anodic bias, the effective interfacial charging capacitance increases, and Mott–Schottky analysis shows an apparent ∼0.15 V flat-band shift with an essentially unchanged slope. Together, these observations are consistent with field-perturbed interfacial charging and altered bias partitioning. Field-dependent impedance and bubble imaging are consistent with magnetohydrodynamic convection that promotes bubble detachment and near-electrode mass transport for both half-reactions, and they reveal an OER-specific high-frequency perturbation under anodic bias. Under field, the heterostructure reaches an OER onset overpotential of ∼261 mV and requires an overpotential of 366 mV at 10 mA cm –2 in alkaline electrolyte. These results illustrate how reticular-framework chemistry, junction engineering, and both built-in and applied fields can program reactivity through interfacial electrostatics and near-electrode transport in organic-framework electrocatalysts.

Garcia-Enriquez, Lissette [Univ. of Texas at El Pa↗

Measured proton electromagnetic structure deviates from theoretical predictions

The visible world is founded on the proton, the only composite building block of matter that is stable in nature. Consequently, understanding the formation of matter relies on explaining the dynamics and the properties of the proton’s bound state. A fundamental property of the proton involves the response of the system to an external electromagnetic field. It is characterized by the electromagnetic polarizabilities that describe how easily the charge and magnetization distributions inside the system are distorted by the electromagnetic field. Moreover, the generalized polarizabilities map out the resulting deformation of the densities in a proton subject to an electromagnetic field. They disclose essential information about the underlying system dynamics and provide a key for decoding the proton structure in terms of the theory of the strong interaction that binds its elementary quark and gluon constituents. Of particular interest is a puzzle in the electric generalized polarizability of the proton that remains unresolved for two decades. Here we report measurements of the proton’s electromagnetic generalized polarizabilities at low four-momentum transfer squared. We show evidence of an anomaly to the behaviour of the proton’s electric generalized polarizability that contradicts the predictions of nuclear theory and derive its signature in the spatial distribution of the induced polarization in the proton. Here, the reported measurements suggest the presence of a new, not-yet-understood dynamical mechanism in the proton and present notable challenges to the nuclear theory.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗