Search NASA⌕ Search

SEARCH · Search NASA

Results for “etching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Unveiling the influence of selective-area-regrowth interfaces on local electronic properties of GaN p-n junctions for efficient power devices

Here, we report correlated nanoscale mapping of the structure, composition, and properties of regrown GaN p-n junctions to identify how etching and non-planar regrowth processes limit diode performance via the introduction of unintentional dopants and defect states. p-GaN was selectively regrown in n-GaN trenches with SiO 2 masks of variable mask-to-trench-width ratio. Dilute Al layers were periodically introduced during regrowth as markers of the growth interface. Correlated nanoscale mapping of doping, conductivity, and dopant complexes was achieved with atom probe tomography (APT), scanning spreading resistance microscopy (SSRM), and cathodoluminescence (CL) spectroscopy, respectively. The Al marker layers, detected by APT, enabled reconstruction of the faceted growth interface and correlation of the dopant concentration with position and time. The p-GaN growth rate is proportional to the mask-to-trench width ratio while the dopant incorporation rate is invariant. At trench edges, magnesium incorporation is suppressed, and oxygen incorporation enhanced, due to preferential incorporation on the semi-polar growth surface, leading to compensation and less abrupt p-n junctions; the SiO 2 mask is a source of oxygen. Residual etch damage below the regrowth interface induces n-type and p-type conductivity, creating leakage pathways. The non-uniform Mg incorporation is driven by crystal anisotropy and is thus inherent to non-planar regrowth, but can be mitigated by engineering the regrowth interface and process parameters. The unprecedented integration of spatially resolved mapping of dopants, impurities, conductivity, and carrier type is a powerful approach to discriminating distinct factors that limit the performance of regrown diodes, enabling the rational optimization of process and device design.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Exploration of methods to remove implanted 210 Pb and 210 Po contamination from silicon surfaces

Radioactive contaminants on the surfaces of detector components can be a problematic source of background events for physics experiments searching for rare processes. Exposure to radon is a specific concern because it can result in the relatively long-lived 210 Pb (and progeny) being implanted to significant subsurface depths such that removal is challenging. Here, in this article, we present results from a broad exploration of cleaning treatments to remove implanted 210 Pb and 210 Po contamination from silicon, which is a material frequently used in rare-events searches. We demonstrate for the first time that heat treatments (“baking”) can effectively mitigate such surface contamination, with a 1200 °C bake resulting in a 97$^{+2}_{-3}$% reduction. We also report results using wet-chemistry and plasma-based methods, which show that etching can be highly effective provided the etch depth is sufficiently aggressive. Our survey of cleaning methods suggests consideration of multiple approaches during the different phases of detector construction to enable greater flexibility for efficient removal of 210 Pb and 210 Po surface contamination.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Alloy selective optical sorting of mixed post-consumer aluminum scrap streams

Shredded post-consumer non-ferrous scrap stream, also known as Zorba, contains a mixture of cast and wrought aluminum pieces with very different compositions. Cast Al pieces, with their high Si, Cu and Fe content, are a major contaminant in wrought scrap fraction, which results in downcycling of the mixed cast + wrought scrap into non-structural cast Al alloys and parts. Here, in this paper, we introduce a chemical treatment method to color-code scrap aluminum pieces by alloy family and demonstrate low-cost optical sorting of cast from wrought pieces to upgrade the scrap stream. We utilized non-acidic chemical solutions that react with (i.e., etch) the scrap pieces to produce colors based on the Al alloy chemistry of a given piece. Cast pieces with high Si and Cu fractions turned black, whereas the much leaner wrought pieces remained unreacted. We showed > 95% sorting efficiency of mixed cast and wrought pieces using a repurposed low-cost optical sorter originally designed for food sorting. We also colored wrought Al pieces by alloy families, such as 5xxx and 6xxx, using a two-step chemical etching technique, which has the potential to create a circular supply chain in which wrought aluminum alloys are sorted from the mixed scrap stream and recycled back to high-value wrought products such as sheets, extrusions, and forgings with minimal contamination from cast scrap.

Aluminum↗
DOE OSTI2016

Evolution of oxygenated cadmium sulfide (CdS:O) during high-temperature CdTe solar cell fabrication

Oxygenated cadmium sulfide (CdS:O) produced by reactive sputtering has emerged as a promising alternative to conventional CdS for use as the n-type window layer in CdTe solar cells. Here, complementary techniques are used to expose the window layer (CdS or CdS:O) in completed superstrate devices and combined with a suite of materials characterization to elucidate its evolution during high temperature device processing. During device fabrication amorphous CdS:O undergoes significant interdiffusion with CdTe and recrystallization, forming CdS1-yTey nanocrystals whose Te fraction approaches solubility limits. Significant oxygen remains after processing, concentrated in sulfate clusters dispersed among the CdS1-yTey alloy phase, accounting for ~30% of the post-processed window layer based on cross-sectional microscopy. Interdiffusion and recrystallization are observed in devices with un-oxygenated CdS, but to a much lesser extent. Etching experiments suggest that the CdS thickness is minimally changed during processing, but the CdS:O window layer is reduced from 100 nm to 60-80 nm, which is confirmed by microscopy. Alloying reduces the band gap of the CdS:O window layer to 2.15 eV, but reductions in thickness and areal density improve its transmission spectrum, which is well matched to device quantum efficiency. The changes to the window layer in the reactive environments of device fabrication are profoundly different than what occurs by thermal annealing in an inert environment, which produced films with a band gap of 2.4 eV for both CdS and CdS:O. These results illustrate for the first time the significant changes that occur to the window layer during processing that are critical to the performance of CdTe solar cells.

14 SOLAR ENERGY↗
DOE OSTI2024

The evolution of model Rh/Fe 3 O 4 (001) catalysts in hydrogen environments

Single metal atoms dispersed on oxides are a new emerging class of catalysts owing to their unique electronic and chemical properties. Here, in this study, we have prepared a series of model single-atom catalysts possessing well-characterized Rh sites that include Rh adatoms (Rh ad ), mixed surface layers with octahedrally-coordinated Rh (Rh oct ), as well as metallic Rh clusters and nanoparticles (Rh met ) on Fe 3 O 4 (001). Using X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM), we investigated the activity of such model systems towards H2 and their stability in reducing environments. Our results show that the atomically dispersed Rhad and Rhoct species do not activate H 2 , which would result in the formation of surface hydroxyls on Fe 3 O 4 (001). In contrast, the presence of Rh met in H 2 results in the formation of hydroxyls and subsequent etching of the Fe 3 O 4 (001) at higher temperatures (≥ 500 K) due to water formation via the Mars-van Krevelen mechanism. Additionally, such surface etching leads to the release of the Rh oct from the surface lattice and their sintering to Rh met . To bridge the material gap between the surface science models and high surface area catalysts, we perform parallel studies on powder Rh/Fe 3 O 4 catalysts. The XPS characterization shows remarkable similarities between these systems. Further, our surface science studies provide an atomistic picture of the behavior of high surface area catalysts in the H 2 atmosphere.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Morphology-Driven Control of Metabolite Selectivity Using Nanostructure-Initiator Mass Spectrometry

Nanostructure-initiator mass spectrometry (NIMS) is a laser desorption/ionization analysis technique based on the vaporization of a nanostructure-trapped liquid "initiator" phase. Here in this work, we report an intriguing relationship between NIMS surface morphology and analyte selectivity. Scanning electron microscopy and spectroscopic ellipsometry were used to characterize the surface morphologies of a series of NIMS substrates generated by anodic electrochemical etching. Mass spectrometry imaging was applied to compare NIMS sensitivity of these various surfaces toward the analysis of diverse analytes. The porosity of NIMS surfaces was found to increase linearly with etching time where the pore size ranged from 4 to 12 nm with corresponding porosities estimated to be 7-70%. Surface morphology was found to significantly and selectively alter NIMS sensitivity. The small molecule (<2k Da) sensitivity was found to increase with increased porosity, whereas low porosity had the highest sensitivity for the largest molecules examined. Estimation of molecular sizes showed that this transition occurs when the pore size is <3× the maximum of molecular dimensions. While the origins of selectivity are unclear, increased signal from small molecules with increased surface area is consistent with a surface area restructuring-driven desorption/ionization process where signal intensity increases with porosity. In contrast, large molecules show highest signal for the low-porosity and small-pore-size surfaces. We attribute this to strong interactions between the initiator-coated pore structures and large molecules that hinder desorption/ionization by trapping large molecules. Lastly, this finding may enable us to design NIMS surfaces with increased specificity to molecules of interest.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Self-Healing Thermal Annealing: Surface Morphological Restructuring Control of GaN Nanorods

With advances in nanolithography and dry etching, top-down methods of nanostructuring have become a widely used tool for improving the efficiency of optoelectronics. These nano dimensions can offer various benefits to the device performance in terms of light extraction and efficiency, but often at the expense of emission color quality. Broadening of the target emission peak and unwanted yellow luminescence are characteristic defect-related effects due to the ion beam etching damage, particularly for III–N based materials. In this article we focus on GaN based nanorods, showing that through thermal annealing the surface roughness and deformities of the crystal structure can be “self-healed”. Correlative electron microscopy and atomic force microscopy show the change from spherical nanorods to faceted hexagonal structures, revealing the temperature-dependent surface morphology faceting evolution. The faceted nanorods were shown to be strain- and defect-free by cathodoluminescence hyperspectral imaging, micro-Raman, and transmission electron microscopy (TEM). In-situ TEM thermal annealing experiments allowed for real time observation of dislocation movements and surface restructuring observed in ex-situ annealing TEM sampling. This thermal annealing investigation gives new insight into the redistribution path of GaN material and dislocation movement post growth, allowing for improved understanding and in turn advances in optoelectronic device processing of compound semiconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Facile Synthesis of Ru-Based Octahedral Nanocages with Ultrathin Walls in a Face-Centered Cubic Structure

Noble-metal nanocages with ultrathin (less than 2 nm) walls and well-defined facets have received great interest owing to their remarkable utilization efficiency of atoms and facet-dependent catalytic activities toward various reactions. Here, we report the synthesis of Ru-based octahedral nanocages covered by {111} facets, together with ultrathin walls in a face-centered cubic (fcc) structure rather than the hexagonal close-packed (hcp) of bulk Ru. The involvement of slow injection for the Ru(III) precursor, the introduction of KBr, and the use of elevated temperature were all instrumental to the formation of Pd@Ru core–shell octahedra with a conformal, uniform shell and a smooth surface. The {111} facets were well preserved during the selective removal of the Pd cores via wet etching, even when the Ru walls were only five atomic layers in thickness. Through in situ XRD, we demonstrated that the fcc structure of the Ru nanocages was stable up to 300 °C. We also used first-principles, self-consistent density functional theory calculations to study the adsorption and dissociation of N2 as a means to predict the catalytic performance toward ammonia synthesis. Our results suggested that the small proportions of Pd atoms left behind in the walls during etching could play a key role in stabilizing the adsorption of N2 as well as in reducing the activation energy barrier to N2 dissociation.

Zhao, Ming↗
DOE OSTI2018

All Roads Lead to TiO 2 : TiO 2 -Rich Surfaces of Barium and Strontium Titanate Prepared by Hydrothermal Synthesis

Through high-resolution electron microscopy, the surface structure of barium titanate and strontium titanate nanoparticles are found to be terminated by a TiO 2 double layer. These results confirm prior observations of TiO 2 -rich surface reconstructions on strontium titanate nanoparticles made hydrothermally at high pH and single crystals prepared with wet chemical etching. Of all the reconstructions observed on single crystals for these two materials, we report for first time the √13 × √13R33.7° structure on the {001} facets of hydrothermally prepared barium titanate and strontium titanate nanocrystals. The aqueous environment common to the two preparation methods preferentially leaves strontium and barium depleted from the A-sites near the surface and leads to TiO 2 -terminated surfaces for both materials. Analysis indicates that the observed structures are the thermodynamic lowest energy structures in aqueous conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Formation and Ripening of Self-Assembled Multilayers from the Vapor-Phase Deposition of Dodecanethiol on Copper Oxide

Here, the vapor-phase reaction of dodecanethiol (DDT) with copper oxide surfaces and the molecular level composition and structure of the resulting films were examined. Atomic force microscopy, cross-sectional transmission electron microscopy, and electron energy loss/electron dispersive spectroscopy reveal that, instead of forming self-assembled monolayers, DDT etches CuO surfaces to create ~8 nm thick Cu-thiolate multilayers. These layers are composed of surprisingly well-ordered crystallites, oriented either parallel or perpendicular to the substrate surface. Pre-etching of the CuO to expose the underlaying copper metal is shown to prevent the formation of multilayers and instead allow for the formation of the expected monolayers. Water contact angle and Fourier transform infrared spectroscopy are further shown to be ineffective at distinguishing the multilayer and monolayer thiol films. Interestingly, the multilayer films are unstable in air, ripening into particles 20 μm wide and several hundred nanometers tall over the course of a week. Air exposure also leads to the slow oxidation of the sulfur and copper within the films at a rate similar to what has been seen before for DDT monolayers. As a result, the multilayers show no significant improvement over monolayers in the prevention of oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Investigating the Chemical Reactivity of Lithium Silicate Model SEI Layers

Silicon anodes suffer from an unstable solid electrolyte interphase (SEI) layer that contributes to undesirable capacity fade with cycling. A key part to addressing this unstable SEI formation is to examine how certain components of the SEI react with the electrolyte over time. One SEI component that has not been thoroughly studied in the context of the chemical reactivity against the electrolyte is lithiated silicate. Four model silicate thin films with increasing lithium content were deposited by radio frequency (RF) magnetron sputtering to study how the lithiation of the native oxide on a silicon anode affects the chemical stability of the anode surface. SiO2, Li2Si2O5, Li2SiO3, and Li3SiOx films were exposed to 1.2 M LiPF6 in the 3:7 wt% ethylene carbonate/ethyl methyl carbonate (EC/EMC) electrolyte for periods of time that are representative of the amount of time it takes to undergo cell formations. Soaked samples were rinsed, dried, and characterized by a combination of attenuated total reflectance-infrared spectroscopy (ATR-IR), focused ion beam-secondary electron microscopy (FIB-SEM), and X-ray photoelectron spectroscopy (XPS) depth profiling. It was found that the rate of the decrease in film thickness of the silicates exposed to the electrolyte over time increases as a function of the lithium content in the thin film. This reaction involves HF etching and LiPF6 salt degradation leading to silicate loss and fluorination throughout the bulk. Understanding this chemical instability is critical to determining the overall mechanism of SEI degradation over time.

ADVANCED PROPULSION SYSTEMS,ENERGY STORAGE↗
DOE OSTI2017

Anisotropic and Interconnected Nanoporous Materials from Randomly End-Linked Copolymer Networks

Microphase separation within randomly end-linked copolymer networks (RECNs) provides access to disordered bicontinuous morphologies over a wide composition range of the constituent network strands. Here, we rely on end-linking of telechelic hydroxyl-terminated polystyrene (PS) and poly(D,Llactide) (PLA) chains of equal molecular weight, with a tetrafunctional isocyanate cross-linker in a good solvent for both strands, followed by solvent removal to induce microphase separation, and finally etching of the PLA phase to yield nanoporous materials. Transmission electron microscopy (TEM) tomographic reconstructed 3D images along with gravimetric measurements and small-angle X-ray scattering (SAXS) indicate the formation of highly interconnected structures over a range of ~40-70 vol % of PLA, while N2 adsorption measurements indicate narrowly distributed pore sizes that can be tuned by varying the strand molecular weights. Stretching of the PS/PLA copolymer networks above the glass transition temperatures of both components prior to etching the PLA phase provides a straightforward means to introduce controlled anisotropy into the 3D interconnected porous materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High- Q Nanophotonic Resonators on Diamond Membranes using Templated Atomic Layer Deposition of TiO 2

Integrating solid-state quantum emitters with nanophotonic resonators is essential for efficient spin-photon interfacing and optical networking applications. While diamond color centers have proven to be excellent candidates for emerging quantum technologies, their integration with optical resonators remains challenging. Conventional approaches based on etching resonators into diamond often negatively impact color center performance and offer low device yield. In this work, we developed an integrated photonics platform based on templated atomic layer deposition of TiO 2 on diamond membranes. Our fabrication method yields high-performance nanophotonic devices while avoiding etching wavelength-scale features into diamond. Moreover, this technique generates highly reproducible optical resonances and can be iterated on individual diamond samples, a unique processing advantage. Our approach is suitable for a broad range of both wavelengths and substrates and can enable high-cooperativity interfacing between cavity photons and coherent defects in diamond or silicon carbide, rare earth ions, or other material systems.

42 ENGINEERING↗
DOE OSTI2016

Ru nanoframes with an fcc structure and enhanced catalytic properties

Noble-metal nanoframes are of great interest to many applications due to their unique open structures. Among various noble metals, Ru has never been made into nanoframes. In this study, we report for the first time an effective method based on seeded growth and chemical etching for the facile synthesis of Ru nanoframes with high purity. The essence of this approach is to induce the preferential growth of Ru on the corners and edges of Pd truncated octahedra as the seeds by kinetic control. The resultant Pd–Ru core–frame octahedra could be easily converted to Ru octahedral nanoframes of ~2 nm in thickness by selectively removing the Pd cores through chemical etching. Most importantly, in this approach the face-centered cubic (fcc) crystal structure of Pd seeds was faithfully replicated by Ru that usually takes an hcp structure. Furthermore, the fcc Ru nanoframes showed higher catalytic activities toward the reduction of p-nitrophenol by NaBH 4 and the dehydrogenation of ammonia borane compared with hcp Ru nanowires with roughly the same thickness.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Unveiling the Degradation Mechanism of High-Temperature Superconductor Bi 2 Sr 2 CaCu 2 O 8+δ in Water-Bearing Environments

We report the physical properties of copper oxide high-temperature superconductors have been studied extensively, such as its band structure, and doping effects of Bi 2 Sr 2 CaCu 2 O 8+δ (Bi-2212). However, some chemical-related properties of these superconductors are rarely reported, such as their stability in air. Here, we report experiments combined with ab initio calculations that address the effects of water in contact with Bi-2212. The evolution of Bi-2212 flake with exposure to water for different time intervals were tested and characterized by optical microscopy (OM), atomic force microscopy (AFM), Raman spectroscopy, transmission electron microscopy (TEM) and electrical measurements. The thickness of Bi-2212 flakes is gradually decreased in water, and some thin flakes can be completely etched away after a few days. The stability of Bi-2212 in other solvents is also evaluated, including alcohol, acetone, HCl and KOH. The morphology of Bi-2212 flakes is relatively stable in organic solvents. However, the flakes are etched relatively quick in HCl and KOH, especially in acidic environment. Our results imply that hydrogen ion is primarily responsible for the deterioration of their properties. Both TEM and calculation results demonstrate that the atoms in Bi-O plane is relatively stable when compared to the inner atoms in Sr-O, Ca-O and Cu-O planes. This work contributes towards understanding the chemical stability of Bi-2212 superconducting device in environmental medium, which is important for both fundamental studies and practical applications of copper oxide high-temperature superconductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Interconnected Nanoporous Polysulfone by the Self-Assembly of Randomly Linked Copolymer Networks and Linear Multiblocks

Porous materials have attracted considerable attention due to their versatile applications, especially in water purification. Interconnected nanoporous structures are distinguished by their high degree of porosity and resistance to clogging, as well as their insensitivity to nanostructural orientation. Previous works on randomly linked copolymer systems have shown that they can effectively produce disordered cocontinuous nanostructures, which upon removal of one component yield interconnected nanoporous materials. However, the cocontinuous nanomaterials previously developed using polystyrene (PS) and poly(d,l-lactic acid) (PLA) strands, and the resulting interconnected nanoporous PS monoliths, were far too brittle to enable practical use as membranes. Here, we study the self-assembly of randomly linked copolymer networks prepared using blocks of the engineering polymer polysulfone (PSU). A wide cocontinuous regime (spanning 40 wt %) was found for randomly end-linked copolymer networks (RECNs) constructed from PSU and PLA strands, via a combination of mechanical testing, gravimetry, small-angle X-ray scattering, and scanning electron microscopy. The PSU/PLA cocontinuous nanomaterial with symmetric composition showed 2.4 times higher Young’s modulus and ~100 times greater toughness than the corresponding PS/PLA sample. The interconnected nanoporous PSU fabricated after etching of PLA even exhibited 1.6 times greater toughness than PS/PLA prior to PLA removal. To facilitate the production of thin films of cocontinuous nanomaterials, we applied solution-processable randomly linked linear PSU/PLA multiblock polymers onto ultrafiltration membranes. Here, the interconnected nanoporous PSU thin film generated by etching PLA was found to effectively reject 50 nm diameter particles without significantly compromising permeability. This discovery presents a valuable addition to the existing techniques used to fabricate PSU membranes. In contrast to traditional methods, which are sensitive to processing conditions, produce a wide range of pore sizes, and offer limited adjustability of pore size, the current technique is anticipated to enable interconnected PSU membranes with more uniform and tailorable porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Three-Tone Chemical Patterns for Block Copolymer Directed Self-Assembly

Chemical patterns for directed self-assembly (DSA) of lamellaeforming block copolymers (BCP) with density multiplication can be fabricated by patterning resist on a cross-linked polystyrene layer, etching to create guide stripes, and depositing end-grafted brushes in between the stripes as background. To date, two-tone chemical patterns have been targeted with the guide stripes preferentially wet by one block of the copolymer and the background chemistry weakly preferentially wet by the other block. In the course of fabricating chemical patterns in an all-track process using 300 mm wafers, it was discovered that the etching process followed by brush grafting could produce a three-tone pattern. We characterized the three regions of the chemical patterns with a combination of SEM, grazing-incidence small-angle X-ray scattering (GISAXS), and assessment of BCP-wetting behavior, and evaluated the DSA behavior on patterns over a range of guide stripe widths. In its best form, the three-tone pattern consists of guide stripes preferentially wet by one block of the copolymer, each flanked by two additional stripes that wet the other block of the copolymer, with a third chemistry as the background. Three-tone patterns guide three times as many BCP domains as two-tone patterns and thus have the potential to provide a larger driving force for the system to assemble into the desired architecture with fewer defects in shorter time and over a larger process window.

block copolymer↗
DOE OSTI2025

Deposition-Dependent Coverage and Performance of Phosphonic Acid Interface Modifiers in Halide Perovskite Optoelectronics

In this work, we study the effect of various deposition methods for phosphonic acid interface modifiers commonly pursued as self-assembled monolayers in high-performance metal halide perovskite photovoltaics and light-emitting diodes. We compare the deposition of (2-(3,6-diiodo-9H-carbazol-9-yl)ethyl)phosphonic acid onto indium tin oxide (ITO) bottom contacts by varying three parameters: the method of deposition, specifically spin coating or prolonged dip coating; ITO surface treatment via HCl/FeCl3 etching; and use in combination with a second modifier, 1,6-hexylenediphosphonic acid. We demonstrate that varying these modification protocols can impact time-resolved photoluminescence carrier lifetimes and quasi-Fermi level splitting of perovskite films deposited onto the phosphonic acid-modified ITO. Ultraviolet photoelectron spectroscopy shows an increase in the effective work function after phosphonic acid modification and clear evidence for photoemission from carbazole functional groups at the ITO surface. We used X-ray photoelectron spectroscopy to probe differences in phosphonic acid coverage on the metal oxide contact and show that perovskite samples grown on ITO with the highest phosphonic acid coverage exhibit the longest carrier lifetimes. Finally, we establish that device performance follows these same trends. These results indicate that the reactivity, heterogeneity, and composition of the bottom contact help to control recombination rates and therefore power conversion efficiencies. ITO etching, prolonged deposition times for phosphonic acids via dip coating, and the use of a secondary, more hydrophilic bisphosphonic acid all contribute to improvements in surface coverage, carrier lifetime, and device efficiency. Furthermore, these improvements each have a positive impact, and we achieve the best results when all three strategies are implemented.

contact engineering↗