Search NASA⌕ Search

SEARCH · Search NASA

Results for “interfacial processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Characterization and measurement of polymer wear

Analytical tools which characterize the polymer wear process are discussed. The devices discussed include: visual observation of polymer wear with SEM, the quantification with surface profilometry and ellipsometry, to study the chemistry with AES, XPS and SIMS, to establish interfacial polymer orientation and accordingly bonding with QUARTIR, polymer state with Raman spectroscopy and stresses that develop in polymer films using a X-ray double crystal camera technique.

Buckley, D. H.↗

Surface effects on phase distributions of a fast-quenched miscibility gap type system - Succinonitrile-water

If a binary homogeneous melt is cooled into an immiscible region, the newly formed second phase will generally have a density different from the parent phase, and will separate readily by sedimentation. Observation of solidification processes in microgravity indicates that outside of sedimentation, at least two other important effets can separate the phases: (1) preferential wetting, and (2) thermal migration of second-phase droplets due to interfacial tension gradients. The latter effect would drive the minority phase along the thermal gradient toward the hottest part (assuming the interfacial tension decreases with increasing temperature), which is usually away from the crucible wall. On the other hand, if the minority phase preferentially wets the crucible, a minority phase layer which thickens as initial solution compositions approach critical, will form adjacent to the solid surface and remain in the coldest region of the ingot. This study presents compelling preliminary evidence that these two effects do exist and that they compete with one another. However, the temperature dependence of preferential wetting below T(c) for the current system of study is, as yet, undetermined. These effects are sensitive to the initial concentration of a hypermonotectic solution cooling through a miscibility gap.

Frazier, D. O.↗

Characterization and measurement of polymer wear

Analytical tools which characterize the polymer wear process are discussed. The devices discussed include: visual observation of polymer wear with SEM, the quantification with surface profilometry and ellipsometry, to study the chemistry with AES, XPS and SIMS, to establish interfacial polymer orientation and accordingly bonding with QUARTIR, polymer state with Raman spectroscopy and stresses that develop in polymer films using a X-ray double crystal camera technique.

Buckley, D. H.↗

AC impedance study of degradation of porous nickel battery electrodes

AC impedance spectra of porous nickel battery electrodes were recorded periodically during charge/discharge cycling in concentrated KOH solution at various temperatures. A transmission line model (TLM) was adopted to represent the impedance of the porous electrodes, and various model parameters were adjusted in a curve fitting routine to reproduce the experimental impedances. Degradation processes were deduced from changes in model parameters with electrode cycling time. In developing the TLM, impedance spectra of planar (nonporous) electrodes were used to represent the pore wall and backing plate interfacial impedances. These data were measured over a range of potentials and temperatures, and an equivalent circuit model was adopted to represent the planar electrode data. Cyclic voltammetry was used to study the characteristics of the oxygen evolution reaction on planar nickel electrodes during charging, since oxygen evolution can affect battery electrode charging efficiency and ultimately electrode cycle life if the overpotential for oxygen evolution is sufficiently low.

Lenhart, Stephen J.↗

Modeling of Non-Isothermal Cryogenic Fluid Sloshing

A computational fluid dynamic model was used to simulate the thermal destratification in an upright self-pressurized cryostat approximately half-filled with liquid nitrogen and subjected to forced sinusoidal lateral shaking. A full three-dimensional computational grid was used to model the tank dynamics, fluid flow and thermodynamics using the ANSYS Fluent code. A non-inertial grid was used which required the addition of momentum and energy source terms to account for the inertial forces, energy transfer and wall reaction forces produced by the shaken tank. The kinetics-based Schrage mass transfer model provided the interfacial mass transfer due to evaporation and condensation at the sloshing interface. The dynamic behavior of the sloshing interface, its amplitude and transition to different wave modes, provided insight into the fluid process at the interface. The tank pressure evolution and temperature profiles compared relatively well with the shaken cryostat experimental test data provided by the Centre National D'Etudes Spatiales.

Cryogenics↗

ZnO buffer layer for metal films on silicon substrates

Dramatic improvements in metallization integrity and electroceramic thin film performance can be achieved by the use of the ZnO buffer layer to minimize interfacial energy between metallization and adhesion layers. In particular, the invention provides a substrate metallization method utilizing a ZnO adhesion layer that has a high work of adhesion, which in turn enables processing under thermal budgets typically reserved for more exotic ceramic, single-crystal, or metal foil substrates. Embodiments of the present invention can be used in a broad range of applications beyond ferroelectric capacitors, including microelectromechanical systems, micro-printed heaters and sensors, and electrochemical energy storage, where integrity of metallized silicon to high temperatures is necessary.

36 MATERIALS SCIENCE↗

Spin-orbit qubit using quantum dots

Methods and apparatus of quantum information processing using quantum dots are provided. Electrons from a 2DEG are confined to the quantum dots and subjected to a magnetic field having a component directed parallel to the interface. Due to interfacial asymmetries, there is created an effective magnetic field that perturbs the energies of the spin states via an interfacial spin-orbit (SO) interaction. This SO interaction is utilized to controllably produce rotations of the electronic spin state, such as X-rotations of the electronic spin state in a double quantum dot (DQD) singlet-triplet (ST) qubit. The desired state rotations are controlled solely by the use of electrical pulses.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Uncertainty methodology for the strongly coupled physical phenomena associated with annular flow

Best-Estimate plus Uncertainty (BEPU) methods are slowly supplanting the use of deterministic analysis methods for thermal-hydraulic analyses. As the uncertainty methodologies evolve it is expected that, where both experimental techniques allow and data are available, there will be a shift to quantifying the uncertainty in increasingly more fundamental parameters. For example, for annular flow in a three-field analysis environment (vapor, liquid film, droplet), the driving parameters would be: a) film interfacial shear stress, b) droplet drag, c) droplet entrainment rate and d) droplet deposition rate. An improved annular flow modeling package was recently developed and implemented in an in-house version of the COBRA-TF best-estimate subchannel analysis tool (Lane, 2009). Significant improvement was observed in the code-to-data predictions of several steam-water annular flow tests following the implementation of this modeling package; however, to apply this model set in formal BEPU analysis requires uncertainty distributions to be determined. The unique aspect of annular flow, and the topic of the present work, is the strong coupling between the interfacial drag, entrainment and deposition phenomena. Ideally the uncertainty in each phenomenon would be isolated; however, the situation is further complicated by an inability to experimentally isolate and measure the individual rate processes (particularly entrainment rate), which results in available experimental data that are inherently integral in nature. This paper presents a methodology for isolating the individual physical phenomena of interest, to the extent that the currently available experimental data allow, and developing the corresponding uncertainty distributions for annular flow. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Tricoupled hybrid lattice Boltzmann model for nonisothermal drying of colloidal suspensions in micropore structures

A tricoupled hybrid lattice Boltzmann model (LBM) is developed to simulate colloidal liquid evaporation and colloidal particle deposition during the nonisothermal drying of colloidal suspensions in micropore structures. An entropic multiple-relaxation-time multirange pseudopotential two-phase LBM for isothermal interfacial flow is first coupled to an extended temperature equation for simulating nonisothermal liquid drying. Then the coupled model is further coupled with a modified convection diffusion equation to consider the nonisothermal drying of colloidal suspensions. Two drying examples are considered. First, drying of colloidal suspensions in a two-pillar micropore structure is simulated in two dimensions (2D), and the final configuration of colloidal particles is compared with the experimental one. Good agreement is observed. Second, at the temperature of 343.15 K ( 70°C ), drying of colloidal suspensions in a complex spiral-shaped micropore structure containing 220 pillars is simulated (also in 2D). The drying pattern follows the designed spiral shape due to capillary pumping, i.e., transport of the liquid from larger pores to smaller ones by capillary pressure difference. Because the colloidal particles are passively carried with liquid, they accumulate at the small menisci as drying proceeds. As liquid evaporates at the small menisci, colloidal particles are deposited, eventually forming solid structures between the pillars (primarily), and at the base of the pillars (secondarily). As a result, the particle deposition conforms to the spiral route. Qualitatively, the simulated liquid and particle configurations agree well with the experimental ones during the entire drying process. Quantitatively, the model demonstrates that the evaporation rate and the particle accumulation rate slowly decrease during drying, similar to what is seen in the experimental results, which is due to the reduction of the liquid-vapor interfacial area. In conclusion, the hybrid model shows the capability and accuracy for simulating nonisothermal drying of colloidal suspensions in a complex micropore structure both qualitatively and quantitatively, as it includes all the required physics and captures all the complex features observed experimentally. Such a tricoupled LBM has a high potential to become an efficient numerical tool for further investigation of real and complex engineering problems incorporating drying of colloidal suspensions in porous media.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Cathode–Sulfide Solid Electrolyte Interfacial Instability: Challenges and Solutions

All-solid-state batteries are a candidate for next-generation energy-storage devices due to potential improvements in energy density and safety compared to current battery technologies. Due to their high ionic conductivity and potential scalability through slurry processing routes, sulfide solid-state electrolytes are promising to replace traditional liquid electrolytes and enable All-solid-state batteries, but stability of cathode-sulfide solid-state electrolytes interfaces requires further improvement. Herein we review common issues encountered at cathode-sulfide SE interfaces and strategies to alleviate these issues.

25 ENERGY STORAGE↗

Interfacial Strength and Physical Properties of Functionalized Graphene - Epoxy Nanocomposites

The toughness and coefficient of thermal expansion of a series of functionalized graphene sheet - epoxy nanocomposites are investigated. Functionalized graphene sheets are produced by splitting graphite oxide into single graphene sheets through a rapid thermal expansion process. These graphene sheets contain approx. 10% oxygen due to the presence of hydroxide, epoxide, and carboxyl functional groups which assist in chemical bond formation with the epoxy matrix. Intrinsic surface functionality is used to graft alkyl amine chains on the graphene sheets, and the addition of excess hardener insures covalent bonding between the epoxide matrix and graphene sheets. Considerable improvement in the epoxy dimensional stability is obtained. An increase in nanocomposite toughness is observed in some cases.

Miller, Sandi G.↗

Liquid Interfacial Electron Microscopy Identifies Nanogalvanic Corrosion in Pearlitic Steel

The nanoscale mechanisms of localized corrosion in low carbon steels have remained elusive due to the complexity of studying the degradative material behavior at nanoscale solid-liquid interfaces. We identified various steps in the nanogalvanic corrosion processes using in-situ liquid-cell scanning transmission electron microscopy (STEM) using a microfluidic holder by Hummingbird Scientific. Initial work, performed at low magnification, identified the initiation point on a 1018 low-carbon steel surface. This initiation point was determined to be a triple junction of two ferrite grains bridging a cementite grain in contact with a baseline electrolyte of 6 uM CO2 dissolved in a buffered (2.78 uM Na2SO4) aqueous solution, pH 6.1. The pre-etched low-carbon steel surface was prepared using focused ion beam lift-out procedures to extract a cross-section of the low-carbon steel surface, which then was thinned to about 150 nm and transferred to a SiN membrane microfluidic window. The transfer was made using a lift-out needle to attach the low-carbon steel lamella to the corner of the SiN window, and then Pt/C deposition held the lamella in contact with the window while it was released from the lift out needle. To identify the triple point on the low carbon steel lamella, prior to attachment on the SiN window, the sample was characterized for compositional variations with energy dispersive x-ray spectroscopy mapping, grain orientation and phase mapping with precession electron diffraction, and thickness mapping with energy filtered transmission electron microscopy. This pre-characterization prior to the in-situ experiment provided a map of the multiphase and multigrain structure, where the in-situ liquid cell imaging provided a clear understanding of the initiation point on the sample. These data were cross-correlated to paint a holistic picture of the triple junction site, enabling low electron-fluence in-situ snapshot imaging to avoid dominating the native corrosion reactions with effects from the incident electron beam. This initial result identified that localized, nanogalvanic corrosion at the phase interface was the dominant corrosion process in the low-carbon steel, so we next targeted the observation of an array of these nanogalvanic features phase boundaries in a pearlite grain. Near-surface ferrite/cementite phase interfaces that typify pearlitic low-carbon steel were extracted, pre-characterized, and imaged for the in-situ corrosion processes. The sample was a cross-section from a pearlite grain, with alternating ferrite and cementite grains that extended microns down from the pre-etched low-carbon steel pipe surface. After contact with a buffered aqueous solution, the phase boundaries between the ferrite and cementite began to dissolve, with observable material loss and thickness changes in the dark-field and bright-field STEM images. Within minutes, the corrosion front proceeded deeper into the material, claiming a thin layer of ferrite around all exposed phase boundaries before progressing laterally into the ferrite matrix, converting the ferrite to corrosion product normal to each buried cementite grain. Formation of the corrosion product causes a volumetric expansion, creating a lateral wedging force that mechanically ejects the cementite grains from their grooves and leaves behind percolation channels into the steel substructure. Rapid and deleterious, this nanogalvanic corrosion pathway represents an important target for understanding and preventing run-away degradation in this common building material. Observation of this corrosion mechanism was enabled by the combination of pre-characterization using standard structural, grain, and compositional analysis in the TEM, which provides maps for understanding the reaction propagation captured in low-dose, in-situ, liquid-cell STEM.

corrosion↗

Improved interfacial state density in Al{sub 2}O{sub 3}/GaAs interfaces using metal-organic chemical vapor deposition

In situ deposition of Al{sub 2}O{sub 3} on GaAs was performed by chemical-vapor-deposition (CVD) with trimethyaluminum and isopropanol as precursors. A gallium-rich region in the Al{sub 2}O{sub 3} thin film above the interface was spontaneously formed via the in situ CVD process. Ga-enrichment of the interface was observed using secondary ion mass spectrometry (SIMS) depth profile measurement. X-ray photoelectron spectroscopy (XPS) results show that the gallium-rich region consists of Al{sub 2}O{sub 3} and Ga{sub 2}O{sub 3}, but no As{sub 2}O{sub 3} was observed. The Ga{sub 2}O{sub 3}-Al{sub 2}O{sub 3} layer above the oxide/GaAs interface reduces the frequency dispersion as measured with capacitance-voltage (C-V) characteristics and lowers the interfacial state density as compared to atomic-layer-deposition *(ALD) deposited films which do not display this gallium enrichment above the interface.

36 MATERIALS SCIENCE↗

Preparation and characterization of morph-genetic aluminum nitride/carbon composites from filter paper

Morph-genetic aluminum nitride/carbon composites with cablelike structure were prepared from filter paper template through the surface sol-gel process and carbothermal nitridation reaction. The resulting materials have a hierarchical structure originating from the morphology of cellulose paper. The aluminum nitride/carbon composites have the core-shell microstructure, the core is graphitic carbon, and the shell is aluminum nitride nanocoating formed by carbothermal nitridation reduction of alumina with the interfacial carbon in nitrogen atmosphere. Scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, and transmission electron microscope were employed to characterize the structural morphology and phase compositions of the final products.

36 MATERIALS SCIENCE↗

Bi‐Continuous W‐Rich Refractory High Entropy Alloy‐Cu Composite: Toward Material Innovation of Nuclear Reactor Coolant System

Abstract Refractory high‐entropy alloys (RHEAs) are considered promising candidate materials for next‐generation nuclear reactors due to their superior mechanical strength, irradiation resistance, and thermal stability at high temperatures. However, the significant positive heat of mixing between refractory alloying elements and Cu, commonly used in cooling systems, poses challenges in forming composite structures. This study addresses the issue using a liquid metal dealloying (LMD) process. A precursor alloy (WTaVTi) with a directional dendrite‐interdendrite structure is fabricated and reacted with molten Cu at 1200 °C for 96 h. This approach produced a RHEA‐Cu composite with a stable interface between RHEA (W 31.5 Ta 30.9 V 21.4 Ti 14.3 ) and Cu, featuring a spontaneously formed W‐rich interlayer that enhances interfacial bonding. The composite showed excellent irradiation resistance, with 30% less swelling under α‐ion irradiation than pure W. It also exhibited low thermal conductivity at room temperature, but reached ≈120 W m −1 ·K −1 at ≈650 °C, surpassing pure W. This temperature‐dependent rise in κ, with a positive gradient of +0.075 W m −1 ·K − 2 , is attributed to decreasing diffuse mismatch at elevated temperatures. The large‐scale reaction and stable microstructure achieved through LMD process highlight its industrial potential. This work offers a strategy for developing high‐performance materials by combining RHEA's radiation resistance with Cu's thermal conductivity for extreme environments.

Chemistry↗

Elucidating Abnormal Grain Growth in Thermomagnetic Processed Materials with Transfer Learning and Reinforcement Learning

The goal of this research program is to establish the mechanism governing local grain boundary motion, which is needed to design and process desirable microstructures for better performance, by identifying the relative contributions of grain boundary (GB) energy and mobility to grain growth. Classical models for grain growth assume that the primary mechanism for reducing the total interfacial energy is area reduction and that GB restructuring is not significant. This assumption implies that grain growth is locally driven by curvature. However, recent experimental observations using new non-destructive 3D x-ray diffraction microscopy techniques (3D-XRM) reveal that classic descriptors (i.e., curvature, number of neighbors, grain size) do not predict real grain growth. Instead, local GB motion appears to be governed by its energy relative to its neighbors such that low-energy boundaries replace those of higher energy. However, simulations that incorporate GB energy anisotropy still fail to reproduce these observations. These discrepancies suggest that the common assumption for grain growth theory must be re-examined to predict and, thus, control microstructure evolution in real polycrystals. A significant challenge to testing this assumption is due to anisotropic GB mobility. Mobility may cause abnormal grain growth or affect the final grain shapes or growth rate but its true contributions are unknown because it is difficult to measure. For example, observations in Fe have found that grains associated with high energy and high mobility boundaries tend to experience abnormal grain growth, whereas abnormal grain growth is associated with low energy and high mobility boundaries in alumina. As mobility and energy both control GB motion, it is challenging to isolate the local driving forces necessary to test the common assumption that the primary mechanism is area reduction. The novelty of this work is the use of machine learning tools to capture GB mobility and energy from 3D-XRM measurements in polycrystals to test the common assumption used in grain growth models. Machine learning can capture high-order correlations in dynamic systems like those found in the evolving GB topology. The PIs have developed a physics-regularized interpretable machine learning microstructure evolution (PRIMME) model that accurately replicates the grain growth behavior of its trained data set.

36 MATERIALS SCIENCE↗

Chemistry Under Cover: Tuning Metal-Graphene Interaction by Reactive Intercalation

Intercalation of metal atoms is an established route for tuning the coupling of graphene to a substrate. The extension to reactive species such as oxygen would set the stage for a wide spectrum of interfacial chemistry. Here we demonstrate the controlled modification of a macroscopic graphene-metal interface by oxygen intercalation. The selective oxidation of a ruthenium surface beneath graphene lifts the strong metal-carbon coupling and restores the characteristic Dirac cones of isolated monolayer graphene. Our experiments establish the competition between low-temperature oxygen intercalation and graphene etching at higher temperatures and suggest that small molecules can populate the space between graphene and metals, with the adsorbate-metal interaction being modified significantly by the presence of graphene. These findings open up new avenues for the processing of graphene for device applications and for performing chemical reactions in the confined space between a metal surface and a graphene sheet.

36 MATERIALS SCIENCE↗

Coherent Phonon-Induced Modulation of Charge Transfer in 2D Hybrid Perovskites

Electron–phonon interactions play an essential role in charge transport and transfer processes in semiconductors. For most structures, tailoring electron–phonon interactions for specific functionality remains elusive. Here, it is shown that, in hybrid perovskites, coherent phonon modes can be used to manipulate charge transfer. In the 2D double perovskite, (AE2T) 2 AgBiI 8 (AE2T: 5,5“-diylbis(amino-ethyl)-(2,2”-(2)thiophene)), the valence band maximum derived from the [Ag 0.5 Bi 0.5 I4] 2– framework lies in close proximity to the AE2T-derived HOMO level, thereby forming a type-II heterostructure. During transient absorption spectroscopy, pulsed excitation creates sustained coherent phonon modes, which periodically modulate the associated electronic levels. Thus, the energy offset at the organic–inorganic interface also oscillates periodically, providing a unique opportunity for modulation of interfacial charge transfer. Density-functional theory corroborates the mechanism and identifies specific phonon modes as likely drivers of the coherent charge transfer. These observations are a striking example of how electron–phonon interactions can be used to manipulate fundamentally important charge and energy transfer processes in hybrid perovskites.

36 MATERIALS SCIENCE↗