Search NASA⌕ Search

SEARCH · Search NASA

Results for “ionic conductivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Dramatically improve the Safety Performance of Li ion Battery Separators and Reduce the Manufacturing Cost Using Ultraviolet Curing and High Precision Coating Technologies

The objective of this project was to improve the safety of operation of Lithium ion batteries (LIB)and at the same time significantly reduce the manufacturing cost of LIB separators. The project was very successful in demonstrating the improved performance and reduced cost attributed to using UV curable binder and high speed printing technology to place a very thin and precisely controlled ceramic layer on the surface of base separators made of polyolefins such as Polyethylene, Polypropylene and combinations of the two as well as cellulosic base separators. The underlying need for this new technology is the recently identified potential of fire in large format Lithium ion batteries used in hybrid, plug-in hybrid and electric vehicles. The primary potential cause of battery fire is thermal runaway caused by several different electrical or mechanical mechanisms; such as, overcharge, puncture, overheating, compaction, and internal short circuit. During thermal runaway, the ideal separator prevents ion flow and continues to physically separate the anode from the cathode. If the temperature of the battery gets higher, the separator may melt and partially clog the pores and help prevent ion flows but it also can shrink which can result in physical contact of the electrodes and accelerate thermal run-away even further. Ceramic coated separators eliminate many of the problems related to the usage of traditional separators. The ceramic coating provides an electrically insulating layer that retains its physical integrity at high temperature, allows for more efficient thermal heat transfer, helps reduce thermal shrinkage, and inhibits dendrite growth that could create a potential short circuit. The use of Ultraviolet (UV) chemistry to bind fine ceramic particles on separators is a unique and innovative approach primarily because of the instant curing of the UV curable binder upon exposure to UV light. This significant reduction in drying/curing time significantly reduces the cost of a ceramic coating. Another innovation is high precision, high speed, printing techniques that can apply a unique pattern of ceramic particles on base separators. The pattern will maximize ionic conductivity and minimize ceramic coating weight and thickness, while retaining the benefits of increased puncture strength, reduced thermal shrinkage and no decomposition. This project has met all of its goals and has been successfully completed. This successful completion has enabled Miltec UV to take the final steps leading to the commercialization of an innovative technology that will result in ceramic coated separators that can be manufactured and sold from the US, with increased production capacity, reduced cost, and improved battery safety.

25 ENERGY STORAGE↗
DOE OSTI2020

Co-Extrusion (CoEx) for Cost Reduction of Advanced High-Energy-and-Power Battery Electrode Manufacturing

Co-Extrusion (CoEx) is a deposition technology developed at PARC that uses engineered fluidic channels to cause multiple streams of dissimilar fluids to impart shape to one another. Here, we describe the use of CoEx to produce structured cathode electrode films to improve electrochemical performance of thick electrode films. CoEx enables us to create structured electrode films that have periodic regions of enhanced ionic conductivity, enabling higher utilization of thicker cathode films at high discharge rates. While increasing electrode thickness is a known method for increasing energy density of battery electrodes, this increase in energy density typically also results in reduced power density. This project, a collaboration between the Palo Alto Research Center, Oak Ridge National Laboratories, and Ford Motor Company, seeks to first validate the benefits of CoEx at the coin cell level, before performing the necessary R&D effort to scale production up to large (10+ Ah) pouch cells that will show increased energy density without a reduction in power density. We used conventional battery materials (commercially available NMC, PVDF, carbon black, and graphite) to produce structured electrodes via CoEx and compared them to thick and thin conventionally produced (unstructured) battery electrodes. CoEx electrodes show improved high rate performance compared to unstructured electrodes, resulting in higher energy density pouch cells compared to the baseline electrode of 7 and 11% in volumetric and gravimetric energy density, respectively. These electrodes also showed substantially improved electrochemical performance at high discharge rates compared to thick conventional electrodes.

25 ENERGY STORAGE↗
DOE OSTI2018

Statically and Dynamically Stable Lithium-sulfur Batteries

The commercialization of lithium-sulfur (Li-S) batteries is hampered by several intrinsic materials challenges: low electronic and ionic conductivity of the active material, severe polysulfide migration from the cathode to the anode, and instability of the Li-metal anode. The poor conductivity limits the electrochemical utilization of the active material and often necessitates a high content of electrochemically inactive, conductive carbon or functional polymers in the cathode region, which lowers the practical energy density. The polysulfide migration causes static and dynamic instabilities with high capacity fade, poisoning of the Li-metal surface, and poor cycling efficiency, hindering the practical viability of Li-S batteries. Recently, it is becoming obvious that the development of practically viable high-energy-density Li-S batteries is determined largely by attaining the necessary cell-design parameters. The essential extrinsic parameters include a sulfur loading of at least 5 mg cm-2, a sulfur content of over 65 wt.%, and a low electrolyte/sulfur (E/S) ratio of less than 11 milliliter per gram. To overcome the above challenges, our group has demonstrated in this project that innovations in polysulfide-filter-coated separators and advanced electrode substrates greatly enhance the electrochemical utilization and efficiency with reasonably high sulfur loadings and low E/S ratios in the cells. This is because Li-S batteries involve conversion reactions unlike the insertion-reaction electrodes in commercial Li-ion batteries, so cell components/designs directly borrowed from Li-ion batteries may need new architectures or chemical/physical characteristics to be adapted to sulfur cathodes. Our cell-component design provides the fabricated Li-S cells with enhanced electrochemical performance: high utilization of the active material, extended cycle life, and good storage properties. More importantly, these custom cell configurations allow the cells to employ the easily prepared sulfur cathodes with a high sulfur loading (up to 60 mg cm-2) and a high sulfur content (80 wt.%) with a low E/S ratio of as low as 4.0 milliliter per gram. Our progress illustrates that the approaches presented and developed in this project offer practically viable solutions for the Li-S technology development.

25 ENERGY STORAGE↗
DOE OSTI2020

Doping effect of Al in LLZO

Lithium ion batteries have become a common use in most electronic devices and transportation. However, the use of liquid electrolytes poses a serious safe hazard due to their high flammability. The narrow operating temperature and voltage windows also limit further improvement of the energy density.Solid-state lithium batteries with the use of more stable and safer solid electrolyte have garnered much attention and could be the future choice for battery technology. A promising potential candidate for the solid electrolyte component is the garnet type Li 7 La 3 Zr 2 O 12 (LLZO) ceramic material since it possesses high ionic conductivity at room temperature and enables the use of high capacity lithium anode and high voltage/capacity cathodes.However, to form the stable cubic phase of LLZO and high densification,high sintering temperatures above 1100°C is typically required, which causes Lithium loss of the system.Many studieshave been taken to dop LLZO with various precursors such as Ga, Ta, and Al to stabilize the cubic structure and reduce calcination temperature, while the doping effect on sintering densification is still unclear. In this study Al doping along with ball milling were explored to stabilize the cubic phase of LLZO and improve densification, while reducing the amount of impurity phases. Samples were synthesized from the precursors Li 2 CO 3 , Al 2 O 3 , La 2 O 3 , and ZrO 2 by ball milling followed by heat treatment for 12 hours at 1000°C. XRD with Rietveld fitting was used to determine the two phases of LLZO (cubic, tetragonal) and other possible secondary phases. Furthermore,SEM with top and cross sectional views was conducted to investigate the morphology and microstructure of sintered pellets.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dual Function Solid State Battery with Self-Forming Self-Healing Electrolyte and Separator (Final Scientific/Technical Report)

Over the course of this program, we have demonstrated an improved rechargeable Li/I2 battery with reduced impedance, improved cyclability, improved Coulombic Efficiency, and the ability to “self-heal” during shorting events. Multi-year efforts have led to the development and improvements in the composition, fabrication, and preparation of the solid state electrolyte, the role of the interface, and design of appropriate test conditions. These investigations have led to significant improvements in Coulombic efficiency. By systematic development of a composite solid state electrolyte, this system is able to self-form upon charge, thus lending itself to long shelf life before use. The initial project objective was to demonstrate a solid-state rechargeable battery based on a Li-metal anode and iodine cathode with a self-forming, self-healing electrolyte and separator with high gravimetric and volumetric energy density. The final deliverables of this project build on a multi-year effort beginning with materials development and design to generate a suitable solid state electrolyte composite with demonstrated higher ionic conductivity compared to the baseline (LiI). Development in cell design and interface modification leading to the generation of rechargeable solid electrolyte cells with Coulombic efficiency improvements of ~3X over initial tests, as well as demonstration of self-healing behavior, where the cells retained their ability to continue extended cycling after shorting events. The hypothesis put forward as part of the initial concept for the project was that the cell chemistry would be self-healing. For example, if a lithium dendrite formed during charge of the cell and reached the iodine cathode, the reaction of the lithium dendrite with the iodine would consume the tip of the dendrite to form lithium iodide, more of the solid electrolyte. The formation of the solid electrolyte would allow the cell to recover and continue to function. This type of self-healing during cycling has been demonstrated and has the potential to improve on safety considerations that stem from shorting events in other Li- containing systems.

25 ENERGY STORAGE↗
DOE OSTI2021

CFA-17-12798: Nanostructured Ceramic Membranes for Enhanced Tritium Management

This project focuses on the novel use of interfacial hydrated layers in ionic conducting ceramic materials for tritiated water (HTO) adsorption and recovery. Low-temperature water adsorption properties of nanoscale structured ceramics combined with hydrogen isotope exchange in their hydrated layers could provide a low-cost and transformative avenue to address tritium management challenges.

08 HYDROGEN↗
DOE OSTI2022

Mechanical, Microstructural, and Electrochemical Characterization of NaSICON Sodium Ion Conductors [Poster]

The DOE Office of Electricity views sodium batteries as a priority in pursuing a safe, resilient, and reliable grid. Improvements in solid-state electrolytes are key to realizing the potential of these large-scale batteries. NaSICON structure consists of SiO 4 or PO 4 tetrahedra sharing common corners with ZrO 6 octahedra. Structure forms “tunnels” in three dimensions that can transport interstitial sodium ion. 3D structure provides higher ionic conductivity than other conductors (β’’-alumina), particularly at low temperature. Lower temperature (cheaper) processing compared to β’’-alumina. Our objective was to identify fundamental structure-processing-property relationships in NaSICON solid electrolytes to inform design for use in sodium batteries. In this work, the mechanical properties of NaSICON sodium ion conductors are affected by sodium conduction. Electrochemical cycling can alter modulus and hardness in NaSICON. Excessive cycling can lead to secondary phases and/or dendrite formation that change mechanical properties in NaSICON. Mechanical and electrochemical properties can be correlated with topographical features to further inform design decisions

25 ENERGY STORAGE↗
DOE OSTI2022

High-Temperature Ceramic-Carbonate Dual-Phase Membrane Reactor for Pre-combustion Carbon Dioxide Capture (Final Scientific/Technical Report)

Arizona State University, in collaboration with University of South Carolina, worked on a project aimed at development of a new high temperature, high pressure CO 2 perm-selective membrane reactor for water-gas-shift reaction (WGS) with simulated gasifier syngas to produce a high concentration H 2 stream with CO 2 capture. The membrane reactor is made of a CO 2 semi-permeable ceramic-carbonate dual-phase (CCDP) membrane with high CO 2 perm-selectivity/permeance and thermal/mechanical stability for application in WGS reaction. The objectives of this project were to (1) synthesize the chemically/thermally stable tubular CCDP membranes with CO 2 permeance and selectivity (with respect to H 2 , CO or H 2 O) larger than 6.5×10-7 mol/m2·s·Pa and 500, respectively; (2) establish CCDP membrane reactor setup and study high pressure CO 2 permeation and WGS reaction with CO 2 capture using the setup; and (3) identify conditions for WGS in the CCDP membrane reactor that produce CO 2 and H 2 streams with purity of >99% and >90% respectively at CO conversion >95% and overall carbon capture >90%. The work in this project included both membrane development and membrane reactor process study. The membrane development efforts were focused on investigating a H 2 S resistant and highly oxygen-ionic conducting metal oxide material and membrane for CO 2 separation, fabrication of tubular samaria-doped-ceria/molten-carbonate CCDP membrane with high mechanical strength, and experimental and modeling study of high-pressure CO 2 permeation of the CCDP membranes. Mathematical models were developed to describe WGS in the CCDP membrane reactor without a catalyst or packed with a commercial high temperature WGS catalyst. Experiments on WGS in the CCDP membrane reactor with the commercial WGS catalyst, guided by the model analysis, were performed to identify optimum conditions for achieving the CO conversion, carbon capture, and the purity of the H 2 and CO 2 streams mentioned above. At 30 atm feed pressure, 750°C operation temperature, space velocity of 250 h-1, and with steam sweep, a single-stage CCDP membrane reactor with average CO 2 permeation flux of 0.5 cm3(STP)/min.cm2 can achieve CO 2 conversion of 95% and overall carbon capture of 94%, and produce CO 2 and H 2 streams with dry-based purity of >99% and 92% respectively. The project also included process design and techno-economic analysis (TEA) for a CCDP membrane reactor process for WGS reaction with CO 2 capture for a 550 MW coal-fired IGCC power plant, and its comparison with the conventional fixed-bed reactor system for WGS with follow-up CO 2 capture by an amine absorption process. The target performance for the reactor for WGS with CO 2 capture includes CO conversion >95%, hydrogen stream purity >90%, CO 2 stream purity >95%, and total carbon capture >90%. The CCDP membrane developed in this project can achieve the performance target, without subsequent CO 2 capture process at the optimum conditions identified in this project. The outcome of the process design and TEA analysis shows that the membrane reactor for WGS with in-situ CO 2 capture has an operating cost about 40% lower than that for the conventional fixed-bed reactor with a separate amine absorption process for CO 2 capture. However, the capital cost of the membrane reactor process is about twice that of the conventional process because of the higher cost of the CCDP membrane. Modeling analysis shows that a membrane reactor using a CCDP membrane with higher CO 2 permeance (about three times the current value) can deliver the targeted performance for WGS reaction with CO 2 capture at a much higher space velocity and lower membrane surface area to catalyst volume ratio, leading to a smaller catalyst amount and/or membrane area and hence significantly reduced membrane reactor capital costs.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Physical and Mechano-Electrochemical Phenomena of Thin Film Lithium-Ceramic Electrolyte Constructs

While a small number of solid electrolytes exhibit high ionic conductivity (~1mS cm at 298K), few are stable against Li metal. The garnet-type solid electrolyte, based on the nominal formula Li 7 La 3 Zr 2 O 12 (LLZO), is unique in that it is a fast ion conductor and – as we demonstrated in our recent project (DE-EE-00006821) – is stable against Li. Moreover, our former project successfully demonstrated a decrease in Li-LLZO interface resistance from 12,000 to 2 Ohms cm 2 and stable cycling at 1 mA cm 2 for 100 cycles (+/- 15 µm Li per cycle). Although the past project (DE-EE-00006821) demonstrated LLZO is a viable solid electrolyte for enabling batteries using metallic Li, the studies used thick pellets (1mm) and thick anodes (~500 µm). We believe that to achieve a step increase in technology readiness level (TRL), the same performance characteristics previously shown should be demonstrated in technologically relevant cells, e.g. thin LLZO and thin Li. The goal of this project is to acquire a deep fundamental understanding of the physical and mechano-electrochemical phenomena that control the performance of cells consisting of thin LLZO (~10 µm), thin Li anodes (~20 µm) and thin solid-state composite cathodes. If successful, the knowledge gained in this project will guide closely related commercialization efforts to scale the production of LLZO-based solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

All Solid State Batteries Enabled by Multifunctional Electrolyte Materials

Solid Power has teamed with University of California San Diego to develop a high energy, long life, low cost, and safe all-solid-state-battery (ASSB). The battery is enabled by a multifunctional solid state electrolyte (SSE). The project enables scalable production of large format solid state batteries required by the vehicle market and building domestic battery manufacturers as leaders in the global vehicle ASSB production. In the project, the multifunctional SSE materials have been developed and optimized with ionic conductivity ≥ 5 mS/cm and electrochemical stability 0 – 4.5V. SSE separator films have been coated by using a roll-to-roll process with thickness ≤ 40 µm. All-solid-state NMC-Li pouch cells containing the developed SSE have been assembled. A cycle life of > 750 at 100% DOD and 45 °C has been demonstrated in a full pouch cell.

25 ENERGY STORAGE↗
DOE OSTI2023

Composite Cathode Architectures Made By Freeze-Casting for All Solid State Lithium Batteries (CRADA Final Report)

As part of a Battery 500 seedling project, MBRDNA partnered with LBNL and Montana State University (MSU) to develop solid-state batteries based on an Al-substituted LLZO (Li 7 La 3 Zr 2 O 12 ) ceramic ion-conductor. All solid-state lithium batteries are attractive contenders for use as power sources for electric vehicles because of their potential for better safety and higher energy density than state-of-the-art lithium-ion batteries, although they are still at early stages of development. Al-substituted LLZO is one of the most promising solid electrolytes for battery applications based on high ionic conductivity, a wide operating voltage window, and apparent stability vs. reduction by lithium. However, difficulties with processing thin (< 20 $\textit{um}$ and dense LLZO membranes have hampered development of devices based on this material. It is non-compressible and must be sintered at high temperatures to densify components. It is also difficult to maintain contact between the active cathode material and LLZO in the composite cathodes, which is critical for successful operation. This research project aimed to use novel processing methods to overcome these issues. The end result was the first ever-reported truly all solid-state battery based on LLZO operating at room temperature without application of exogenous pressure. During the course of the project, we also identified a number of issues that need to be addressed to improve the technology readiness level of this battery.

25 ENERGY STORAGE↗
DOE OSTI2022

High Energy Aqueous Lithium-Ion Batteries (Final Report)

Lithium-ion batteries (LIBs) are a widely used energy storage device. For decades, researchers have been studying aqueous electrolytes due to their non-flammability and environmental friendless. However, the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) of water greatly limit the voltage window of the aqueous electrolyte. The recent concept of ‘solvent-in-salt’ electrolytes, namely ‘water-in-salt’ electrolytes (WISE) for aqueous batteries and ‘super-concentrated’ electrolytes for non-aqueous batteries, greatly expands the electrochemical window of these battery systems and consequently their energy density. This expansion occurs because the large number of salt aggregates in ‘solvent-in-salt’ electrolytes enables preferential salt decomposition over solvent decomposition to form robust interphase layers on electrodes, thus enhancing their stability in a wide range of operating voltages. However, even when the salt concentration reached 63m, regardless of cost, the cathodic potential of the WISE expanded only to 1.75V with an overall electrochemical stability window of <3.25V. To design the next generation of high energy aqueous LIBs, electrolytes that possess a wider electrochemical stability window and lower cost but still maintain the merit of non-flammability are much needed. In this project, we designed the aqueous LIBs with widened voltage window. We reported a cheap and non-flammable ternary eutectic electrolyte that can form a robust solid electrolyte interface (SEI)so that the cathodic limiting potential can be decreased to <1.5 V for Li 4 Ti 5 O 12 anodes, while maintaining both a high ionic conductivity of >10 -3 S cm –1 and a low viscosity. We demonstrated the super-stable2.5V LiMn 2 O 4 ||Li 4 Ti 5 O 12 pouch cell with mass loading of 2.5 mAh/cm. Further, LiCl-LiBr-Graphite/Li full cells were designed with high energy density. Finally, we use a bi-layer design to enlarge the voltage window of aqueous electrolyte, which can endow the stable cycling of aqueous Lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Safe Electrolytes for Batteries

The demand for reliable and safe lithium-ion batteries (LIBs) for electric vehicles (EVs) and energy storage systems (ESS) necessitates the exploration of nonflammable phosphorus-based electrolytes as alternatives to the traditional flammable carbonate-based ones. However, integrating phosphorus-based electrolyte poses challenges, including capacity fading and compatibility issues with graphite material. Here, a high-throughput (HTP) electrochemical characterization method, similar to PH test paper, is introduced to fast screen compatible phosphorus-based electrolyte for use with graphite. Among 1,740 combinations of phosphorus-based electrolytes and graphite materials, 101 promising combinations are identified for further evaluation. These identified phosphorus-based electrolytes and graphite materials are evaluated and optimized in Li/Graphite half-cells and Graphite/LiFePO 4 (LFP) full-cells using commercial-level electrodes. The desolvation energy of a complex with one Li+ and four solvent molecules of phosphate or carbonate is calculated by density functional theory (DFT). Key parameters such as viscosity, ionic conductivity, and flammability of the electrolytes are thoroughly tested and optimized. The modified phosphate-dominant electrolyte (2 M LiFSI TEP/DME/EC (6/2/2, volume ratio) + 5 wt.% VEC + 5 wt.% FEC) demonstrates excellent thermal stability with lithiated graphite and showcases superior cycling performance in the Graphite/LFP full cell, surpassing prior research findings in phosphate-dominant electrolytes. By the rapid HTP screening and identification of compatible electrolyte-graphite combinations, this approach contributes to expediting the development of safer LIBs for EVs and ESS.

25 ENERGY STORAGE↗
DOE OSTI2023

First Principles Modeling of Cluster-Based Solid Electrolytes (Final Technical Report)

Given the trend of global warming and the urgent need to transition from fossil fuels to green energy, lithium-ion batteries continue to be an integral part of our lives. Design, development, and understanding of novel solid-state electrolyte materials play the key role for achieving next-generation all-solid-state batteries with high energy and great safety. The current modeling schemes to develop advanced solid electrolytes are focusing on materials in which the building blocks are individual atoms. Our theoretical approach is a paradigm shift in solid-state electrolyte design. Instead of atoms, we focus on clusters as the building blocks and model these solid electrolytes and their interfaces with electrodes, especially Li-metal anode, for their successful implementation in solid-state batteries. The advantage of using the cluster ions to replace elemental ions is that the size, composition, and shape of the former can be tailored to achieve higher ionic conductivity at room temperature, electrochemical stability, and charge transfer across solid-solid interfaces than conventional materials. Specifically, the project includes: (1) Developing cluster-based solid electrolytes, where the halogen components are replaced by cluster ions that mimic the chemistry of halogens but are characterized by additional degrees of freedom, including the size, shape, composition, and motional dynamics under excitation. (2) Providing a fundamental understanding of the ion conduction mechanism in the developed cluster-based solid electrolytes; (3) Modeling the interfacial properties (i.e., structural, chemical, and transport properties) between the cluster-based solid electrolytes and electrodes at the atomic level. For the cluster-based solid electrolytes incompatible with the Li-metal anode or cathode materials, potential candidates for interfacial coatings are identified and studied. (4) Providing a theoretical framework towards optimizing critical parameters of the solid-state electrolytes that guides experimentalists to attain desired cathode-electrode interface for cluster-based solid-state electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2023

Development of 3D Printing Techniques for Solid-State Lithium Batteries: Energy Storage Internship (Final Report)

The goal of this internship was to develop a solid polymer electrolyte with a suitable ionic conductivity and mechanical properties and integrate it with 3D printed cathode for solid state lithium batteries. While liquid electrolytes will have much higher conductivities and therefore higher power densities than solid electrolytes, batteries with such electrolytes suffer from extreme dendritic growth, short-circuiting, and general failure. Typically, batteries prevent this by including a solid yet porous separator somewhere between the anode and cathode to suppress dendritic growth. Solid polymer electrolyte acts as the conductive medium between electrodes as well as the separator that prevents failure from short-circuiting. The specific system explored is a vinyl ethylene carbonate (VEC) and polyethylene glycol diacrylate (PEGDA) mixed polymer solution using both 2,2’-azobis(2-methylpropionitrile) (AIBN) and Irgacure 819, respectively as thermal and photo- initiators. Electrochemical and rheological techniques were used to determine the optimal polymer solution and curing conditions. Through this research, multiple new pathways of exploration have been determined to create a usable solid polymer electrolyte through a combination of varying cure intensities and initiator concentrations.

25 ENERGY STORAGE↗
DOE OSTI2023

VTO FY23 Annual Progress Report on 3D Printing of All-Solid-State Lithium Batteries

All-solid-state lithium metal batteries (ASSLBs) have attracted attention due to their potential for mitigating safety issues and addressing energy density limitations of conventional lithium-ion batteries (LIBs). While solid state electrolytes (SSEs) with room-temperature ionic conductivities greater than that of their liquid electrolyte counterparts have been discovered, integration of the different solid components of ASSLBs is not trivial. Taking garnet Li 7 La 3 Zr 2 O 12 (LLZO) electrolyte as an example, problems for this SSE include brittleness, high temperature processing for densification, poor contact with electrodes, and lack of scalable manufacturing methods. These obstacles must be overcome before LLZO becomes commercially viable for ASSLB applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Electrical, structural and thermomechanical properties of doped-LaCrO3 ceramics for high temperature electronics and sensing applications.

Many important electrical and sensor applications require stable conductors under working temperatures up to 1500oC various redox environments. Common high temperature conductors such as nitrides and carbides are not stable under oxidizing atmospheres, for this reason low redox behavior materials would be more attractive. In this work, further dopant studies of the LaCrO3 system were completed in order to control the electronic and ionic conductivity, as well as the relative chemical and microstructural stability. Neodymium and Niobium dopants were initially studied to control the p-type, and potentially n-type conductive mechanisms, respectively, but other dopants strategies were also investigated. The electrical conductivity and Seebeck coefficient were characterized up to 1500oC under varying oxygen partial pressures. The phase and microstructural evolution of each material was also investigated for these compositions by XRD and SEM. The materials showing the best electrical and thermomechanical performance were included within thick films sensors and were tested.

20 FOSSIL-FUELED POWER PLANTS↗