Search NASA⌕ Search

SEARCH · Search NASA

Results for “model structural error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Ball bearing vibrations amplitude modeling and test comparisons

Bearings generate disturbances that, when combined with structural gains of a momentum wheel, contribute to induced vibration in the wheel. The frequencies generated by a ball bearing are defined by the bearing's geometry and defects. The amplitudes at these frequencies are dependent upon the actual geometry variations from perfection; therefore, a geometrically perfect bearing will produce no amplitudes at the kinematic frequencies that the design generates. Because perfect geometry can only be approached, emitted vibrations do occur. The most significant vibration is at the spin frequency and can be balanced out in the build process. Other frequencies' amplitudes, however, cannot be balanced out. Momentum wheels are usually the single largest source of vibrations in a spacecraft and can contribute to pointing inaccuracies if emitted vibrations ring the structure or are in the high-gain bandwidth of a sensitive pointing control loop. It is therefore important to be able to provide an a priori knowledge of possible amplitudes that are singular in source or are a result of interacting defects that do not reveal themselves in normal frequency prediction equations. This paper will describe the computer model that provides for the incorporation of bearing geometry errors and then develops an estimation of actual amplitudes and frequencies. Test results were correlated with the model. A momentum wheel was producing an unacceptable 74 Hz amplitude. The model was used to simulate geometry errors and proved successful in identifying a cause that was verified when the parts were inspected.

Hightower, Richard A., III↗
NASA NTRS1998

Stratospheric Assimilation of Chemical Tracer Observations Using a Kalman Filter: Chi-Square Validated Results and Analysis of Variance and Correlation Dynamics - Pt. 2

A Kalman filter system designed for the assimilation of limb-sounding observations of stratospheric chemical tracers, which has four tunable covariance parameters, was developed in Part I (Menard et al. 1998) The assimilation results of CH4 observations from the Cryogenic Limb Array Etalon Sounder instrument (CLAES) and the Halogen Observation Experiment instrument (HALOE) on board of the Upper Atmosphere Research Satellite are described in this paper. A robust (chi)(sup 2) criterion, which provides a statistical validation of the forecast and observational error covariances, was used to estimate the tunable variance parameters of the system. In particular, an estimate of the model error variance was obtained. The effect of model error on the forecast error variance became critical after only three days of assimilation of CLAES observations, although it took 14 days of forecast to double the initial error variance. We further found that the model error due to numerical discretization as arising in the standard Kalman filter algorithm, is comparable in size to the physical model error due to wind and transport modeling errors together. Separate assimilations of CLAES and HALOE observations were compared to validate the state estimate away from the observed locations. A wave-breaking event that took place several thousands of kilometers away from the HALOE observation locations was well captured by the Kalman filter due to highly anisotropic forecast error correlations. The forecast error correlation in the assimilation of the CLAES observations was found to have a structure similar to that in pure forecast mode except for smaller length scales. Finally, we have conducted an analysis of the variance and correlation dynamics to determine their relative importance in chemical tracer assimilation problems. Results show that the optimality of a tracer assimilation system depends, for the most part, on having flow-dependent error correlation rather than on evolving the error variance.

Menard, Richard↗
NASA NTRS2005

Thermal Conductivity and Specific Heat Measurements of Candidate Structural Materials for the JWST Optical Bench

The James Webb Space Telescope will include an optical bench known as the integrated science instrument module (ISIM). Candidate structural materials for the ISIM must have low density, high stiffness, high thermal conductivity, and low thermal expansion coefficient at the operating temperature of 30 Kelvin. The specific heat is also important in modeling the on-orbit cooldown. We built two different systems for measuring the thermal conductivity and specific heat of samples between 4 Kelvin and 290 Kelvin. Both experiments were carefully designed to minimize potential errors due to radiative heat transfer. We chose the cooling system and instrumentation to allow long-term unattended operation. Software was developed to automate each experiment. It used an algorithm designed to ensure that each system was in thermal equilibrium before a measurement was taken. We describe the two experiments and present the data.

Canavan, E. R.↗
NASA NTRS2015

Wing Shape Sensing from Measured Strain

A new two-step theory is investigated for predicting the deflection and slope of an entire structure using strain measurements at discrete locations. In the first step, a measured strain is fitted using a piecewise least-squares curve fitting method together with the cubic spline technique. These fitted strains are integrated twice to obtain deflection data along the fibers. In the second step, computed deflection along the fibers are combined with a finite element model of the structure in order to interpolate and extrapolate the deflection and slope of the entire structure through the use of the System Equivalent Reduction and Expansion Process. The theory is first validated on a computational model, a cantilevered rectangular plate wing. The theory is then applied to test data from a cantilevered swept-plate wing model. Computed results are compared with finite element results, results using another strain-based method, and photogrammetry data. For the computational model under an aeroelastic load, maximum deflection errors in the fore and aft, lateral, and vertical directions are -3.2 percent, 0.28 percent, and 0.09 percent, respectively; and maximum slope errors in roll and pitch directions are 0.28 percent and -3.2 percent, respectively. For the experimental model, deflection results at the tip are shown to be accurate to within 3.8 percent of the photogrammetry data and are accurate to within 2.2 percent in most cases. In general, excellent matching between target and computed values are accomplished in this study. Future refinement of this theory will allow it to monitor the deflection and health of an entire aircraft in real time, allowing for aerodynamic load computation, active flexible motion control, and active induced drag reduction..

system equivalent reduction and expansion process↗
NASA NTRS1981

Structure of the solar chromosphere. III - Models of the EUV brightness components of the quiet-sun

The described investigation is concerned with the solution of the non-LTE optically thick transfer equations for hydrogen, carbon, and other constituents to determine semiempirical models for six components of the quiet solar chromosphere. For a given temperature-height distribution, the solution is obtained of the equations of statistical equilibrium, radiative transfer for lines and continua, and hydrostatic equilibrium to find the ionization and excitation conditions for each atomic constituent. The emergent spectrum is calculated, and a trial and error approach is used to adjust the temperature distribution so that the emergent spectrum is in best agreement with the observed one. The relationship between semiempirical models determined in this way and theoretical models based on radiative equilibrium is discussed by Avrett (1977). Harvard Skylab EUV observations are used to determine models for a number of quiet-sun regions.

Vernazza, J. E.↗
DOE OSTI2025

Turbulent Processes that Influence Boundary-Layer Cloud Structure (Final Technical Report)

Many models of the atmosphere simulate vertical profiles of observable fields, such as temperature, moisture, and vertical velocity. To assess the realism of such model output, it is important to evaluate the modeled profiles against observations. However, many extant evaluations consist of comparing time averaged profiles from the model and the observations. Such time averages can smooth out unrealistic features that appear in instantaneous profiles. In this way, the time averages may obscure certain model errors from detection. For instance, many models misrepresent turbulent processes, leading to profiles that are too smoothed out or too noisy. E.g., if a model has coarse vertical resolution and overly strong diffusion, then the model may be unable to produce observed sharp peaks. On the other hand, a model may have artificial approximations that produce spurious jumps in the vertical. Much can be learned by browsing through instantaneous snapshots of model output. But the volume of output produced by a global model is far too great to rely purely on visual inspection. In addition, we need a way to statistically characterize the profiles, so that anomalies can be detected more conveniently.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Comparison of Machine Learning Approaches for Prediction of the Equivalent Alkane Carbon Number for Microemulsions Based on Molecular Properties

The chemical properties of oils are vital in the design of microemulsion systems. The hydrophilic–lipophilic difference equation used to predict microemulsions’ phase behavior expresses the oils’ physiochemical properties as the equivalent alkane carbon number (EACN). The experimental determination of EACN requires knowledge of the temperature dependence of the microemulsion system and the effects of different surfactant concentrations. Thus, the experimental determination is time-intensive and tedious, requiring days to months for proper separations. Furthermore, the experiments require high purity of chemicals because microemulsions are sensitive to impurities. Our work focuses on the quick and reliable predictions of the EACN with machine learning (ML) models. Due to the immaturity of ML chemical predictions, we compare three graph neural networks (GNNs) and a gradient-boosted tree algorithm, known as XGBoost. The GNNs use the molecular structures represented as simplified molecular-input line-entry system (SMILES) codes for the initial input, which allows us to assess whether geometry optimization is necessary for reliable results. The XGBoost model also begins with the SMILES representations of the molecules but uses molecular descriptors instead of geometry optimizations. As a result, the best model tested (crystal graph convolutional neural network with Merck molecular force field-94) has an error of 1.15 EACN units of the true EACN for unknown data with the errors skewed toward zero and an R² score of 0.9

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Systematic analysis of magnetic equilibrium reconstruction with eddy currents on LTX- β

Magnetic equilibrium reconstruction in the Lithium Tokamak Experiment-Beta (LTX-β) is complicated by strong eddy currents and toroidal asymmetries arising from its segmented, close-fitting conducting shell. In the earlier experiment LTX, these three-dimensional (3D) conductor effects significantly distorted diagnostic signals and challenged conventional axisymmetric reconstruction methods. In this work, we demonstrate that accurate plasma equilibria can be recovered on LTX-β by incorporating a small number of dominant eddy current modes derived from realistic conductor models. Using the open-source $\tt{TokaMaker}$ Grad–Shafranov solver, we reconstruct equilibria across a systematically selected set of LTX-β discharges and validate them against the legacy $\tt{PSI-Tri}$ hybrid 2D-3D code. Our results show that fully 2D $\tt{TokaMaker}$ reconstructions achieve significantly improved agreement with flux loop and Mirnov probe measurements, reducing total chi-squared fitting errors, especially during startup. Finally, we develop new hybrid 2D-3D $\tt{TokaMaker}$ reconstructions by integrating the $\tt{ThinCurr}$ 3D eddy current model, which we optimize for significant further reduction of chi-squared in most scenarios. These findings underscore the importance of realistic wall-current modeling in short-pulse tokamaks, and establish a physics-based reconstruction framework that is extensible to devices with complex passive structures and 3D wall interactions.

Grad–Shafranov solver↗
NASA NTRS1984

The p-wave upper mantle structure beneath an active spreading centre - The Gulf of California

Over 1400 seismograms of earthquakes in Mexico are analyzed and data sets for the travel time, apparent phase velocity, and relative amplitude information are utilized to produce a tightly constrained, detailed model for depths to 900 km beneath an active oceanic ridge region, the Gulf of California. The data are combined by first inverting the travel times, perturbing that model to fit the p-delta data, and then performing trial and error synthetic seismogram modelling to fit the short-period waveforms. The final model satisfies all three data sets. The ridge model is similar to existing upper mantle models for shield, tectonic-continental, and arc-trench regimes below 400 km, but differs significantly in the upper 350 km. Ridge model velocities are very low in this depth range; the model 'catches up' with the others with a very large velocity gradient from 225 to 390 km.

Walck, M. C.↗
NASA NTRS1998

Experiment 1: Orbital Processing of High-Quality Zn-Alloyed CdTe Compound Semiconductors

Zinc-alloyed cadmium telluride (Zn:CdTe) crystals were grown in unit gravity and in microgravity for comparative analysis. Two crystals were grown on USML-1/STS-50 in 1992, and two additional crystals were grown on USML-2/STS-73 in 1995. The Crystal Growth Furnace (CGF) in the seeded Bridgman-Stockbarger crystal growth geometry was utilized on both missions. Crystals grown on USML-1/STS-50 were found to have solidified with partial wall contact due to the near-absence of the hydrostatic pressure in microgravity, a residual g-vector that was not axial, and the nonwetting sample/ampoule wetting conditions. Crystals grown on USML-2/STS-73 included: a sample/ampoule identical to the USML-1/STS-73 sample/ampoule, with the addition of a restraining spring to simulate hydrostatic pressure internally, and a tapered ampoule which accomplished 2.2 cm of crystal growth without wall contact. Infrared transmission of all ground and flight samples was found to be 63-66 percent, very close to the theoretical 66 percent, suggesting good stoichiometric control. Infrared microscopy confirmed that the primary precipitates were Te and their size (1-10 microns) and density suggested that the flight- and ground-base samples experienced similar thermal histories. Longitudinal macrosegregation, calculated using scaling analysis, was predicted to be low. Nearly diffusion controlled growth was achieved even in unit gravity and macrosegregation data could be fit with a diffusion controlled model. Radial segregation was monitored and was found to vary with fraction solidified, particularly through the shoulder region, where the sample cross section was varying significantly. It was also disturbed in the flight samples in regions where asymmetric wall contact was noted. In regions where a steady state was established, the radial segregation was invariant within our experimental measurement error. Flight samples were found to be much higher in structural perfection than samples processed in unit gravity under identical growth conditions. In regions where solidification had occurred without wall contact, the free surfaces evidenced virtually no twinning, although twins appeared in the flight samples in regions of wall contact and were pervasive in the ground samples. These results were confirmed using optical microscopy and synchrotron x-ray white beam topography. Full-width half-maximum rocking curve widths (FWHM), recorded in arc-seconds, were significantly reduced from 20 a-s (1 g) to 9 a-s (micro-g) for the best regions of the crystals. The 9 a-s (FWHM) rocking curve value in the unconfined flight samples equals the best value reported terrestrially for this material. The ground samples exhibited a fully developed (111)[110] dislocation mosaic structure, whereas dislocations within the flight samples were discrete and no mosaic structure was evident. The defect density was quantitatively reduced from 75,000 (1 g) to 800 (micro-g) +/-50 percent. Dislocation etch pit density results were confirmed using transmission synchrotron white beam and monochromated beam topography. The low defect density is thought to have resulted from the near absence of hydrostatic pressure, which allowed the molten boule to solidify with little or no wall contact. This minimized the transfer of hoop stresses during solidification and post-solidification processing.

Larson, D. J., Jr.↗
NASA NTRS2019

Estimation of coarse dead wood stocks in intact and degraded forests in the Brazilian Amazon using airborne lidar

Coarse dead wood is an important component of forest carbon stocks, but it is rarely measured in Amazon forests and is typically excluded from regional forest carbon budgets. Our study is based on line intercept sampling for fallen coarse dead wood conducted along 103 transects with a total length of 48 km matched with forest inventory plots where standing coarse dead wood was measured in the footprints of larger areas of airborne lidar acquisitions. We developed models to relate lidar metrics and Landsat time series variables to coarse dead wood stocks for intact, logged, burned, or logged and burned forests. Canopy characteristics such as gap area produced significant individual relations for logged forests. For total fallen plus standing coarse dead wood (hereafter defined as total coarse dead wood), the relative root mean square error for models with only lidar metrics ranged from 33 % in logged forest to up to 36 % in burned forests. The addition of historical information improved model performance slightly for intact forests (31 % against 35 % relative root mean square error), not justifying the use of a number of disturbance events from historical satellite images (Landsat) with airborne lidar data. Lidar-derived estimates of total coarse dead wood compared favorably with independent ground-based sampling for areas up to several hundred hectares. The relations found between total coarse dead wood and variables quantifying forest structure derived from airborne lidar highlight the opportunity to quantify this important but rarely measured component of forest carbon over large areas in tropical forests.

Brazilian Amazon↗
NASA NTRSDate not supplied

3D Geolocation of Simulated Lightning Sources from Low-Earth Orbit

The recent removal of the Lightning Imaging Sensor from the International Space Station has left an observational gap in lightning detection from low-Earth orbit (LEO). However, new studies have demonstrated the potential for 3D geolocation of lightning sources using orbiting sensors. The Cubespark mission concept aims to take advantage of these developments by deploying a constellation of satellites with radio frequency (RF) sensors and optical imagers to not only map lightning locations, but also to collect bi-spectral flash images. These new capabilities include mapping storm charge structure, flash channel structure, and distinguishing microphysical processes throughout flash development, helping link microphysics and convective processes with overall flash and storm structure around the globe from LEO. In this study, we simulate lightning RF sources in the very high frequency (VHF) band, extrapolate their signals to space-based detection using an improved ionospheric model, and reconstruct their 3D locations using a time-of-arrival (TOA) minimization algorithm. Various constellation configurations, locations, and atmospheric conditions are considered in order to identify and quantify the three main sources of geolocation error: geometric, ionospheric, and instrumental effects. The promising results of this study emphasize the potential of space-based 3D lightning mapping under diverse conditions. 3D resolution is shown to be better than 1-2 km in many cases, enabling new global applications in meteorology and climate sciences. Here we present a selection of these geolocation results as seen from space alongside recent advancements, paving the way for a future generation of LEO lightning mappers.

CubeSpark↗
NASA NTRSDate not supplied

Segmented Hexagonal Antenna Reflector Concentrically Stacked Using Shape Memory Composite Tubular Hinges

A new architecture for solid surface reflector antennas scalable to sizes greater than 10 m is presented. The design uses compact, light, and simple advanced deployable structures to create sub-reflectors that can be assembled in space into larger units using a robotic arm. The seven-panel hexagonal sub-reflector is divided into hexagonal panels that stack concentrically and vertically. The central panel is connected to each side panel on the back side by a pair of tubular shape memory composite hinges that enable the required deployment kinematics with controlled dynamics. A secondary mechanism closes the interpanel gap. The focus of the paper is on the development of the sub-reflector elements, namely the tubular hinges that use embedded heaters and sensors for triggering and control, the actuation mechanisms, and the lightweight sandwich construction reflector panels. A parametric study using finite element analyses was conducted to assess how design features of the hinge affect its stowage and deployment dynamics. The preliminary component fabrication and testing results for the two-panel assembly breadboard model are outlined. Finally, the results of the test campaign with the brassboard reflector model are presented. A comparison of deployed reflector surface deviation between the measured surface after the stowage and deployment process and the pre-test scans and the nominal surface revealed root mean square errors of less than 1 mm, as required by X-band radiofrequency transmission.

gravity offloading methods↗
DOE OSTI2020

On the possibility of baryon acoustic oscillation measurements at redshift z > 7.6 with the Roman space telescope

ABSTRACT The Nancy Grace Roman Space Telescope (RST), with its field of view and high sensitivity will make surveys of cosmological large-scale structure possible at high redshifts. We investigate the possibility of detecting baryon acoustic oscillations (BAO) at redshifts z > 7.6 for use as a standard ruler. We use data from the hydrodynamic simulation bluetides in conjunction with the gigaparsec-scale Outer Rim simulation and a model for patchy reionization to create mock RST High Latitude Survey grism data for Lyman α emission line selected galaxies at redshifts z = 7.4 to z = 10, covering 2280 deg2. We measure the monopoles of galaxies in the mock catalogues and fit the BAO features. We find that for a line flux of $L = 7\times 10^{-17} \ {\rm erg\, s^{-1}\, cm}^{-2}$, the 5σ detection limit for the current design, the BAO feature is partially detectable (measured in three out of four survey quadrants analysed independently). The resulting root mean square error on the angular diameter distance to z = 7.7 is 7.9 ${{\ \rm per\ cent}}$. If we improve the detection sensitivity by a factor of two (i.e. $L = 3.5\times 10^{-17} \ {\rm erg\, s^{-1}\, cm}^{-2}$), the distance error reduces to $1.4{{\ \rm per\ cent}}$. We caution that many more factors are yet to be modelled, including dust obscuration, the damping wing due to the intergalactic medium, and low redshift interlopers. If these issues do not strongly affect the results, or different observational techniques (such as use of multiple lines) can mitigate them, RST, or similar instruments may be able to constrain the angular diameter distance to the high redshift universe.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

On the discretization error of the discrete generalized quantum master equation

The transfer tensor method (TTM) [Cerrillo and Cao, Phys. Rev. Lett. 112 , 110401 (2014)] can be considered a discrete-time formulation of the Nakajima–Zwanzig quantum master equation (NZ-QME) for modeling non-Markovian quantum dynamics. A recent paper [Makri, J. Chem. Theory Comput. 21 , 5037 (2025)] raised concerns regarding the consistency of the TTM discretization, particularly a spurious term at the initial time t = 0. Here, this work presents a detailed analysis of the discretization structure of the TTM, clarifying the origin of the initial-time correction and establishing a consistent relationship between the TTM discrete-time memory kernel K N and the continuous-time NZ-QME kernel $\mathscr{K}$( N Δ t ). This relationship is validated numerically using the spin-boson model, demonstrating convergence of reconstructed memory kernels and accurate dynamical evolution as Δ t → 0. While the TTM provides a consistent discretization, we note that alternative schemes are also viable, such as the midpoint derivative/midpoint integral scheme proposed in Makri’s work. The relative performance of various schemes for either computing accurate $\mathscr{K}$( N Δ t ) from exact dynamics or obtaining accurate dynamics from exact $\mathscr{K}$( N Δ t ) warrants further investigation.

Density-matrix↗
DOE OSTI2026

Virtual refrigerant charge sensor for variable-speed heat pumps based on feature selection

The refrigerant charge level in heat pump systems significantly impacts their energy efficiency. Virtual refrigerant charge (VRC) sensing technology has been comprehensively investigated and well-established due to its lower cost compared to physical sensors. However, the previous VRC research often relied on expert judgment and physical reasoning for their variable selection, which can potentially select redundant (or highly correlated) or insignificant features, and it is also primarily focused on single-speed systems. To address these challenges, this study proposes a VRC algorithm for variable-speed heat pumps that selects features through a rigorous feature selection method in combination with physical insights. We also propose a piecewise linear model structure segmented by subcooling temperature to accurately predict charge levels, particularly when subcooling temperatures are substantially low. The proposed algorithm was evaluated using experimental data of a residential R410A heat pump, and the performance was compared with two baseline VRC algorithms. The results are: (1) The proposed algorithm outperforms for the case with subcooling temperature less than 1 °C. (2) The proposed algorithm achieves a tested mean absolute percentage error (MAPE) of 4.23%, and improves the overall accuracy for cooling conditions by approximately 60%, compared with the two baseline algorithms. (3) The proposed algorithm uses two fewer features and improves the accuracy for undercharge cooling conditions by 68.0%, compared with baseline algorithm 2. These improvements enhance prediction accuracy and prevent overfitting, providing a more reliable refrigerant charge level prediction and helping improve the heat pump energy efficiency.

Liang, Chenjiyu↗
DOE OSTI2026

Maximizing dynamic range and performance of anatase TiO 2 ECRAM through structure and programming

Here, in this study, we investigate the structure-dependent modulation characteristics of all-solid-state three-terminal electrochemical random-access memory (ECRAM) based on an anatase Li x TiO 2 channel. By directly comparing “asymmetric” and “symmetric” ECRAM device architectures, we reveal significant insight into the impact of a non-zero gate-drain open-circuit voltage and its influence on voltage vs. current-controlled gating. We also explore the impact of potentiation/depression write parameters on the symmetry, linearity, and dynamic range of the device response. Together, initial results from optimizing structure and programming approaches yielded unprecedented G max /G min ratios of >1,000 for ECRAM and hundreds of tunable memory states with excellent linearity and symmetry. Simulations based on these ECRAM devices further illustrate the promise of this analog memory technology, achieving near 2% classification error in the MNIST digit recognition benchmark for a range of training parameters compared to a theoretical best of 1.66% and outperforming other device models extracted from the literature.

AIHWKit↗
DOE OSTI2024

Bhatnagar-Gross-Krook subgrid model for neutrino quantum kinetics

Here, we present a new subgrid model for neutrino quantum kinetics, which is primarily designed to incorporate effects of collective neutrino oscillations into neutrino-radiation-hydrodynamic simulations for core-collapse supernovae and mergers of compact objects. We approximate the neutrino oscillation term in a quantum kinetic equation using the Bhatnagar-Gross-Krook (BGK) relaxation-time prescription, and the transport equation is directly applicable for classical neutrino transport schemes. The BGK model is motivated by recent theoretical indications that nonlinear phases of collective neutrino oscillations settle into quasisteady structures. We explicitly provide basic equations of the BGK subgrid model for both multiangle and moment-based neutrino transport to facilitate the implementation of the subgrid model in the existing neutrino transport schemes. We also show the capability of our BGK subgrid model by comparing it to fully quantum kinetic simulations for fast neutrino-flavor conversion. We find that the overall properties can be well reproduced in the subgrid model; the error of angular-averaged survival probability of neutrinos is within ~20%. By identifying the source of error, we also discuss perspectives to improve the accuracy of the subgrid model.

79 ASTRONOMY AND ASTROPHYSICS↗