Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

High-precision calculation of the strange nucleon electromagnetic form factors

We report a direct lattice QCD calculation of the strange nucleon electromagnetic form factors G s E and G s M in the kinematic range 0 ≤ Q 2 ≤ 1.2GeV 2 . For the first time, both G s E and G s M are shown to be nonzero with high significance. This work uses closer-to-physical lattice parameters than previous calculations, and achieves an unprecented statistical precision by implementing a recently proposed variance reduction technique called hierarchical probing . We perform model-independent fits of the form factor shapes using the z-expansion and determine the strange electric and magnetic radii and magnetic moment. As a result, we compare our results to parity-violating electron-proton scattering data and to other theoretical studies.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Dual-Wavelength Y-Branch DBR Lasers With 100 mW of CW Power Near 2 μm

In this study, the interband GaSb-based diode lasers emitting simultaneously in two narrow bands separated by either ~1.6 or ~3.3 THz were designed, fabricated and characterized. The device active region contained one asymmetric tunnel-coupled double quantum well with separation between two lowest electron subbands controlled by thickness of the tunnel barrier. The Y-branch 6th order distributed Bragg reflector devices have been fabricated with either deep or shallow etched ridge waveguides. The increase of the deeply etched ridge waveguide width from 10 to 20 μm improved laser threshold and efficiency thanks to reduction of the relative role of the sidewall defect recombination. Further improvement of the device performance parameter was achieved by shallow etching. The shallow etched lasers with stable dual-wavelength emission spectrum generated 100 mW of continuous wave output power at 20 °C

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Impact of using linear optimization models in dose planning for HDR brachytherapy

Purpose: Dose plans generated with optimization models hitherto used in high-dose-rate (HDR) brachytherapy have shown a tendency to yield longer dwell times than manually optimized plans. Concern has been raised for the corresponding undesired hot spots, and various methods to mitigate these have been developed. The hypotheses upon this work is based are (a) that one cause for the long dwell times is the use of objective functions comprising simple linear penalties and (b) that alternative penalties, as these are piecewise linear, would lead to reduced length of individual dwell times. Methods: The characteristics of the linear penalties and the piecewise linear penalties are analyzed mathematically. Experimental comparisons between the two types of penalties are carried out retrospectively for a set of prostate cancer patients. Results: When the two types of penalties are compared, significant changes can be seen in the dwell times, while most dose-volume parameters do not differ significantly. On average, total dwell times were reduced by 4.2%, with a reduction of maximum dwell times by 25%, when the alternative penalties were used. Conclusions: The use of linear penalties in optimization models for HDR brachytherapy is one cause for the undesired long dwell times that arise in mathematically optimized plans. By introducing alternative penalties, a significant reduction in dwell times can be achieved for HDR brachytherapy dose plans. Although various measures for mitigating the long dwell times are already available, the observation that linear penalties contribute to their appearance is of fundamental interest.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Plasma Synthesized Doped Boron Nanopowder for MgB 2 Superconductors

Under this program, a process to synthesize nano-sized doped boron powder by a plasma synthesis process was developed and scaled up from 20 gram batches at program start to over 200 grams by program end. Over 75 batches of boron nanopowder were made by RF plasma synthesis. Particle sizes were typically in the 20-200 nm range. The powder was synthesized by the reductive pyrolysis of BCl 3 in hydrogen in an RF plasma. A wide range of process parameters were investigated including plasma power, torch geometry, gas flow rates, and process pressure. The powder-in-tube technique was used to make monofilament and multifilament superconducting wires. MgB 2 wire made with Specialty Materials plasma synthesized boron nanopowder exhibited superconducting properties that significantly exceeded the program goals. Superconducting critical currents, J c , in excess of 10 5 A cm -2 at magnetic fields of 8 tesla were reproducibly achieved. The upper critical magnetic field in wires fabricated with program boron powder were H c2 (0) = 37 tesla, demonstrating the potential of these materials for high field magnet applications. T c in carbon-doped MgB 2 powder showed a systematic decrease with increasing carbon precursor gas flows, indicating the plasma synthesis process can give precise control over dopant concentrations. Synthesis rates increased by a factor of 400% over the course of the program, demonstrating the scalability of the powder synthesis process. The plasma synthesis equipment at Specialty Materials has successfully and reproducibly made high quality boron nanopowder for MgB 2 superconductors. Research and development from this program enabled Specialty Materials to successfully scale up the powder synthesis process by a factor of ten and to double the size of its powder pilot plant. Thus far the program has been a technical success. It is anticipated that continued systematic development of plasma processing parameters, dopant chemistry and concentration, wire processing technology, and collection technology will lead to the commercialization of boron nanopowder as a precursor for MgB 2 superconductors. Potential commercial applications include magnets for magnetic resonance imaging (MRI), fault current limiters, wind turbine generators.

08 HYDROGEN↗

The sensitivity of core-collapse supernovae to nuclear electron capture

A weak-rate library aimed at investigating the sensitivity of astrophysical environments to variations of electron-capture rates on medium-heavy nuclei has been developed. With this library, the sensitivity of the core-collapse and early post-bounce phases of core-collapse supernovae to nuclear electron capture is examined. The rates are adjusted by factors consistent with uncertainties indicated by comparing theoretical rates to those deduced from charge-exchange and β-decay measurements. To ensure a model-independent assessment, sensitivity studies across a comprehensive set of progenitors and equations of state are performed. We find a +16/−4% range in the mass of the inner core at shock formation and a ±20% range of peak ν{sub e} luminosity during the deleptonization burst. These ranges are five times as large as those seen from a separate progenitor study, where we evaluate the sensitivity of these parameters to 32 presupernova models. Additionally, the simulations are found to be more sensitive to a reduction in electron-capture rates than an enhancement, and specifically to the reduction in rates for neutron-rich nuclei near the N = 50 closed neutron shell. As measurements for medium-heavy (A>65) and neutron-rich nuclei are sparse, and because accurate theoretical models that account for nuclear structure considerations of individual nuclei are not readily available, rates for these nuclei may be overestimated. If more accurate estimates confirm this, results from this study indicate that significant changes to the core-collapse trajectory are expected. For this reason, experimental and theoretical efforts should focus on this region of the nuclear chart.

79 ASTRONOMY AND ASTROPHYSICS↗

An Optical/Near-infrared Investigation of HD 100546 b with the Gemini Planet Imager and MagAO

In this paper, we present H band spectroscopic and Hα photometric observations of HD 100546 obtained with the Gemini Planet Imager and the Magellan Visible AO camera. We detect H band emission at the location of the protoplanet HD 100546 b, but show that the choice of data processing parameters strongly affects the morphology of this source. It appears point-like in some aggressive reductions, but rejoins an extended disk structure in the majority of the others. Furthermore, we demonstrate that this emission appears stationary on a timescale of 4.6 years, inconsistent at the 2σ level with a Keplerian clockwise orbit at 59 au in the disk plane. The H band spectrum of the emission is inconsistent with any type of low effective temperature object or accreting protoplanetary disk. It strongly suggests a scattered-light origin, as this is consistent with the spectrum of the star and the spectra extracted at other locations in the disk. A non-detection at the 5σ level of HD 100546 b in differential Hα imaging places an upper limit, assuming the protoplanet lies in a gap free of extinction, on the accretion luminosity of 1.7 × 10 -4 L ⊙ and $M\dot{M}\lt 6.3\times {10}^{-7}\,{M}_{\mathrm{Jup}}^{2}\,{\mathrm{yr}}^{-1}$ for 1 R Jup . These limits are comparable to the accretion luminosity and accretion rate of T-Tauri stars or LkCa 15 b. Taken together, these lines of evidence suggest that the H band source at the location of HD 100546 b is not emitted by a planetary photosphere or an accreting circumplanetary disk but is a disk feature enhanced by the point-spread function subtraction process. Lastly, this non-detection is consistent with the non-detection in the K band reported in an earlier study but does not exclude the possibility that HD 100546 b is deeply embedded.

79 ASTRONOMY AND ASTROPHYSICS↗

An aerodynamic study of scramjet fuel injectors

The aerodynamic drag and fuel distribution patterns of injectors designed for a supersonic combustion ramjet were measured at Mach numbers of 2, 2.5, and 3. The most significant parameter effecting the drag was found to be the injector thickness ratio. A two-fold reduction in the thickness ratio caused a 65 percent decrease in drag. Changing the injector sweep angle a factor of 2 resulted in only a small change in drag. A reversal of injector sweep, from sweepback to sweepforward, did not change the measured drag. Helium gas was injected through the struts to simulate the penetration and spreading patterns of hydrogen. Sampling measurements were made at approximately 2 duct heights downstream of the combustor. The spacing required between fuel injectors was found to be about 10 jet diameters. The effect of gas injection on the measured drag was found to be minor.

Povinelli, L. A.↗

A theoretical study of the application of jet flap circulation control for reduction of rotor vibratory forces

The results of a study to investigate the theoretical potential of a jet-flap control system for reducing the vertical and horizontal non-cancelling helicopter rotor blade root shears are presented. A computer simulation describing the jet-flap control rotor system was developed to examine the reduction of each harmonic of the transmitted shears as a function of various rotor and jet parameters, rotor operating conditions and rotor configurations. The computer simulation of the air-loads included the influences of nonuniform inflow and blade elastic motions. (no hub motions were allowed.) The rotor trim and total rotor power (including jet compressor power) were also determined. It was found that all harmonics of the transmitted horizontal and vertical shears could be suppressed simultaneously using a single jet control.

Piziali, R. A.↗

An improved lunar moment of inertia determination - A proposed strategy

A strategy for determining an improved lunar moment of inertia is proposed. An improved uncertainty in the lunar inhomogeneity parameter could reduce the core density error from 4.20 gr/cu cm to 0.1 gm/cu cm for the case of a lunar density model having a 300 km core radius. The current error of 0.0025 for the lunar inhomogeneity parameter is mostly due to the uncertainties in the C20 and C22 gravity harmonics. An optimum reduction strategy for obtaining an order of magnitude improvement in the gravity estimates is based on covariance analyses of Doppler data. The long-arc reduction method is shown to provide better results than the short-arc technique, and the use of an orbit with a 7000 km semimajor axis along with certain terms of up to degree and order eight is recommended.

Ananda, M. P.↗

Approximation theory for boundary layer suction through individual slits

The basic concepts of influencing boundary layers are summarized, especially the prevention of flow detachment and the reduction of frictional resistance. A mathematical analysis of suction through a slit is presented with two parameters, for thickness and for shape of the boundary layer, being introduced to specify the flow's velocity profile behind the slit. An approximation of the shape parameter produces a useful formula, which can be used to determine the most favorable position of the slit. An aerodynamic example is given.

Walz, A.↗

Space station power semiconductor package

A package of high-power switching semiconductors for the space station have been designed and fabricated. The package includes a high-voltage (600 volts) high current (50 amps) NPN Fast Switching Power Transistor and a high-voltage (1200 volts), high-current (50 amps) Fast Recovery Diode. The package features an isolated collector for the transistors and an isolated anode for the diode. Beryllia is used as the isolation material resulting in a thermal resistance for both devices of .2 degrees per watt. Additional features include a hermetical seal for long life -- greater than 10 years in a space environment. Also, the package design resulted in a low electrical energy loss with the reduction of eddy currents, stray inductances, circuit inductance, and capacitance. The required package design and device parameters have been achieved. Test results for the transistor and diode utilizing the space station package is given.

Balodis, Vilnis↗

Model reduction for discrete bilinear systems

A model reduction method for discrete bilinear systems is developed which matches q sets of Volterra and covariance parameters. These parameters are shown to represent both deterministic and stochastic attributes of the discrete bilinear system. A reduced order model which matches these q sets of parameters is defined to be a q-Volterra covariance equivalent realization (q-Volterra COVER). An algorithm is presented which constructs a class of q-Volterra COVERs parameterized by solutions to a Hermitian, quadratic, matrix equation. The algorithm is applied to a bilinear model of a robot manipulator.

King, A. M.↗

A parametric study of transonic blade-vortex interaction noise

Several parameters of transonic blade-vortex interactions (BVI) are being studied and some ideas for noise reduction are introduced and tested using numerical simulation. The model used is the two-dimensional high frequency transonic small disturbance equation with regions of distributed vorticity (VTRAN2 code). The far-field noise signals are obtained by using the Kirchhoff method with extends the numerical 2-D near-field aerodynamic results to the linear acoustic 3-D far-field. The BVI noise mechanisms are explained and the effects of vortex type and strength, and angle of attack are studied. Particularly, airfoil shape modifications which lead to noise reduction are investigated. The results presented are expected to be helpful for better understanding of the nature of the BVI noise and better blade design.

Lyrintzis, A. S.↗

Vibration reduction in helicopter rotors using an active control surface located on the blade

A feasibility study of vibration reduction in a four-bladed helicopter rotor using individual blade control (IBC), which is implemented by an individually controlled aerodynamic surface located on each blade, is presented. For this exploratory study, a simple offset-hinged spring restrained model of the blade is used with fully coupled flap-lag-torsional dynamics for each blade. Deterministic controllers based on local and global system models are implemented to reduce 4/rev hub loads using both an actively controlled aerodynamic surface on each blade as well as conventional IBC, where the complete blade undergoes cyclic pitch change. The effectiveness of the two approaches for simultaneous reduction of the 4/rev hub shears and hub moments is compared. Conventional IBC requires considerably more power to achieve approximately the same level of vibration reduction as that obtained by implementing IBC using an active control surface located on the outboard segment of the blade. The effect of blade torsional flexibility on the vibration reduction effectiveness of the actively controlled surface was also considered and it was found that this parameter has a very substantial influence.

Millott, T. A.↗

A parameter estimation algorithm for spatial sine testing - Theory and evaluation

This paper presents the theory and an evaluation of a spatial sine testing parameter estimation algorithm that uses directly the measured forced mode of vibration and the measured force vector. The parameter estimation algorithm uses an ARMA model and a recursive QR algorithm is applied for data reduction. In this first evaluation, the algorithm has been applied to a frequency response matrix (which is a particular set of forced mode of vibration) using a sliding frequency window. The objective of the sliding frequency window is to execute the analysis simultaneously with the data acquisition. Since the pole values and the modal density are obtained from this analysis during the acquisition, the analysis information can be used to help determine the forcing vectors during the experimental data acquisition.

Rost, R. W.↗

A miniature fatigue test machine

The objective is to enable the student to generate statistically sound fatigue data sets on wire specimens of varying diameter, microstructure, or material. The student can then assess the effect of these parameters of fatigue resistance. The student can also be exposed to ASTM techniques for fatigue data reduction and presentation. Experiments involving variable amplitude block loading are also easily conducted.

Tipton, Steven M.↗

The Effect of Fiber-Angle Fidelity on the Linear Response of Tow-steered Composite Plates

Composite laminate tailoring is traditionally performed by uniformly changing the in-plane ply orientation to obtain the desired mechanical performance. The emergence of tow-steered plies, where the fibers follow a prescribed curvilinear path, have increased the tailorability of composite laminates. However, characterizing the behavior of tow-steered laminates using finite element analysis is challenging because additional, and often numerous, orientation definitions may be required. The additional orientation definitions detrimentally increase the computational cost and hinder the use of advanced analysis techniques, such as Monte Carlo or uncertainty quantification, in the design process. To reduce computational cost without adversely affecting mechanics-based performance, the results of a parametric study that was used to investigate the effects of fiber-angle fidelity, element size, and tow-steered radius-of-curvature on various loading scenarios for tow-steered composite plates are presented. The three loading scenarios that were analyzed using finite element analysis included an axial tension load, an applied constant through-thickness-direction pressure load, and an axial compression load. Results for mechanics-based metrics of interest are presented and discussed for each loading scenario. Little sensitivity (less than one percent difference) to the effect of fiber-angle fidelity is observed in the mechanics-based metrics until the coarse-end of the considered range. Sensitivity to element size generally dominates the observed results for the mechanics-based metrics. Notable reductions in the preprocessing time are observed for increasingly coarse element size and fiber-rounding parameters. The preprocessing times decreased up to three orders of magnitude from a few thousand seconds to a few seconds without loss of accuracy in the mechanics-based metrics. Such increased computational performance is of particular interest to the structural design and analysis communities that may be conducting large counts of finite-element analyses, such as in other parametric studies, Monte-Carlo analyses, uncertainty quantification, or tow-steered optimization.

tow-steered composites↗