Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Preliminary subsystem designs for the Assured Crew Return Vehicle (ACRV), volume 1

A series of design studies is presented concerning the Assured Crew Return Vehicle (ACRV) for Space Station Freedom. Four alternate designs are presented for the ACRV braking and landing system. Options presented include: ballistic and lifting body reentries; the use of high-lift, high-payload aerodynamic decelerators, as well as conventional parachutes; landing systems designed for water landings, land landings, or both; and an aerial recovery system. All four design options presented combine some or all of the above attributes, and all meet performance requirements established by the ACRV Program Office. Two studies of ACRV growth options are also presented. Use of the ACRV or a similarly designed vehicle in several roles for possible future space missions is discussed, along with the required changes to a basic ACRV to allow it to perform these missions optimally. The outcome of these studies is a set of recommendations to the ACRV Program Office describing the vehicle characteristics of the basic ACRV which lend themselves most readily to be adapted for use in other missions. Finally, the impacts on the design of the ACRV due to its role as a medical emergency vehicle were studied and are presented. The use of the ACRV in this manner will impact its shape, internal configuration, and equipment.

Source record↗
NASA NTRS1998

Synthesis and Characterization of Modified Phenylethynyl Imides

As an ongoing effort to develop structural adhesives for high-performance aerospace applications, recent work has focused on phenylethynyl terminated imide (PETI) oligomers. The work reported herein involves the synthesis and characterization of a series of phenylethynyl containing oligomers designated LARC(TM) MPEI (modified phenylethynyl imide). These oligomers presumably contain mixtures of linear, branched and star-shaped molecules. The fully imidized polymers exhibited minimum melt viscosities as low as 600 poise at 335 C, significantly lower than equivalent molecular weight linear materials. Ti/Ti lap shear specimens processed at 288 C under 15 psi showed tensile shear strengths as high as approx. 6000 psi and 5200 psi at ambient temperature and 177 C respectively. The chemistry and properties of these new MPEIs are presented and compared with an optimized linear PETI, LARC(TM)PETI-5.

Jensen, B. J.↗
NASA NTRS2004

Habitat Utilization Assessment - Building in Behaviors

Habitability, and the associated architectural and design attributes of an environment, is a powerful performance shaping factor. By identifying how inhabitants use an area, we can draw conclusions about what design or architectural attributes cause what behaviors and systematically design in desired human performance. We are analyzing how a crew uses a long duration habitat and work environment during a four-day underwater mission and identifying certain architectural and design attributes that are related to, and potential enablers of, certain crew behaviors. By identifying how inhabitants use the habitat, we can draw conclusions about what habitability attributes cause what behaviors and systematically design in desired human performance (applicable to NASA's Bioastronautics Human Behavior and Performance Critical Path Roadmap question 6.12). This assessment replicates a methodology reported in a chapter titled "Sociokinetic Analysis as a Tool for Optimization of Environmental Design" by C. Adams.' That study collected video imagery of certain areas of a closed habitat during a 91 day test and from that data calculated time spent in different volumes during the mission, and characterized the behaviors occurring in certain habitat volumes thus concluding various rules for design of such habitats. This study assesses the utilization of the Aquarius Habitat, an underwater station, which will support six Aquanauts for a fourteen-day mission during which the crew will perform specific scientific and engineering studies. Video is recorded for long uninterrupted periods of time during the mission and from that data the time spent in each area is calculated. In addition, qualitative and descriptive analysis of the types of behaviors in each area is performed with the purpose of identifying any behaviors that are not typical of a certain area. If a participant uses an area in a way different from expected, a subsequent analysis of the features of that area may result in conclusions of performance shaping factors. With the addition of this study, we can make comparisons between the two different habitats and begin drawing correlation judgments about design features and behavior. Ideally, this methodology should be repeated in additional Aquarius missions and other analog environments because the real information will come from comparisons between habitats.

Whitmore, Mihriban↗
NASA NTRS1974

Analytical solution of the optimal three dimensional reentry problem using Chapman's exact equations

This paper presents the general solution for the optimal three dimensional aerodynamic control of a lifting vehicle entering a planetary atmosphere. A set of dimensionless variables is introduced, and the resulting exact equations of motion have the distinctive advantage that they are completely free of the physical characteristics of the vehicle. Furthermore, a general lift-drag polar is used to define the aerodynamic control. Hence, the results obtained apply to any type of vehicle of arbitrary weight, dimensions and shape, having an arbitrary polar and entering any planetary atmosphere.

Vinh, N. X.↗
NASA NTRS1978

The practical impact of elastohydrodynamic lubrication

Elastohydrodynamic lubrication has had its most significant impact on, among all the types of concentrated contact mechanisms, rolling element bearings. EHL technology, through its inclusion in computer codes, now provides us with more effective methods for optimizing bearing design and for predicting bearing life, power loss, temperature and dynamic behavior. Bearing life prediction has advanced to a much more sophisticated level as compared to the calculation of fatigue life based on Lundberg-Palmgren theory. Application of elastohydrodynamics to gearing has, more or less, been limited to the calculation of pitch point film thicknesses. Techniques for calculating film thicknesses over the entire range of tooth meshes for arbitrarily shaped gear teeth (noninvolute, spur, helical, etc.) need to be developed. Elastomer seals with both unidirectional and reciprocating motion offer a fruitful application for the elastohydrodynamics of low modulus materials.

Anderson, W. J.↗
NASA NTRS1984

The accuracy of altimetric surfaces

Estimates of the shape of the sea surface as determined from satellite altimeters have become of increasing importance in geophysics, geodesy and physical oceanography. The most effective error reduction procedures used in producing these surfaces have been some version of a crossing-arc analysis. The problem with this procedure is the absence of an easy means of evaluating the noise structure of the final result. By recasting the problem as one of objective mapping (optimal estimation) the error reduction is optimized and an explicit estimate is obtained of the wave-number structure of the final altimetric surface. Examples, suitable to a small computer, have been generated to show that the error reduction along the sub-satellite tracks is very great, with most of the residual lying in long wavelengths.

Wunsch, C.↗
NASA NTRS1997

Validation of an Accurate Three-Dimensional Helical Slow-Wave Circuit Model

The helical slow-wave circuit embodies a helical coil of rectangular tape supported in a metal barrel by dielectric support rods. Although the helix slow-wave circuit remains the mainstay of the traveling-wave tube (TWT) industry because of its exceptionally wide bandwidth, a full helical circuit, without significant dimensional approximations, has not been successfully modeled until now. Numerous attempts have been made to analyze the helical slow-wave circuit so that the performance could be accurately predicted without actually building it, but because of its complex geometry, many geometrical approximations became necessary rendering the previous models inaccurate. In the course of this research it has been demonstrated that using the simulation code, MAFIA, the helical structure can be modeled with actual tape width and thickness, dielectric support rod geometry and materials. To demonstrate the accuracy of the MAFIA model, the cold-test parameters including dispersion, on-axis interaction impedance and attenuation have been calculated for several helical TWT slow-wave circuits with a variety of support rod geometries including rectangular and T-shaped rods, as well as various support rod materials including isotropic, anisotropic and partially metal coated dielectrics. Compared with experimentally measured results, the agreement is excellent. With the accuracy of the MAFIA helical model validated, the code was used to investigate several conventional geometric approximations in an attempt to obtain the most computationally efficient model. Several simplifications were made to a standard model including replacing the helical tape with filaments, and replacing rectangular support rods with shapes conforming to the cylindrical coordinate system with effective permittivity. The approximate models are compared with the standard model in terms of cold-test characteristics and computational time. The model was also used to determine the sensitivity of various circuit parameters including typical manufacturing dimensional tolerances and support rod permittivity. By varying the circuit parameters of an accurate model using MAFIA, these sensitivities can be computed for manufacturing concerns, and design optimization previous to fabrication, thus eliminating the need for costly experimental iterations. Several variations were made to a standard helical circuit using MAFIA to investigate the effect that variations on helical tape and support rod width, metallized loading height and support rod permittivity, have on TWT cold-test characteristics.

Kory, Carol L.↗
NASA NTRS2010

Mimas: Preliminary Evidence For Amorphous Water Ice from VIMS

We have conducted a statistical clustering analysis (1,2) on a mosaic of VIMS data cubes obtained on February 13, 2010, for Saturn s satellite Mimas. Seven VIMS cubes were geometrically projected and re-sampled to a common spatial resolution. The clustering technique consists of a partitioning algorithm coupled to a criterion that prevents sub-optimal solutions and tests for the influence of random noise in the measurements. The clustering technique is agnostic about the meaning of the clusters, and scientific interpretation requires their a posteriori evaluation. The preliminary results yielded five clusters, demonstrating that spectral variability across Mimas surface is statistically significant. The ratios of the means calculated for each of the clusters show structure within the 1.6- micron water ice band, as well as the shape and the central wavelength of the strong ice band at 2 micron, that map spatially in patterns apparently related to the topography of Mimas, in particular certain regions in and around Herschel crater. The mean spectra of the five clusters, show similarities with laboratory spectra of amorphous and crystalline H2O ice (3) that are suggestive of the presence of an amorphous ice component in certain regions of Mimas, notably on the central peak of Herschel, on the crater floor, and in faults surrounding the crater. This may represent a mixture of both ice phases, or perhaps a layer of amorphous ice on a base of crystalline ice. Another possible occurrence of amorphous ice appears southwest of Herschel, close to the south pole.

Cruikshank, Dale P.↗
NASA NTRS2019

Electron Beam Welding of Pure Tungsten Hex Cans for Nuclear Thermal Propulsion Engines

Nuclear thermal propulsion (NTP) is an in-space propulsion method currently being developed at the NASA Marshall Space Flight Center (MSFC). NTP systems are a high specific impulse (750–1,100 s), high thrust (15,000–250,000 lbf ) method of propulsion which have the potential to allow for faster transit times when optimizing for high ΔV. In the nuclear rocket engine, the heat from the nuclear fission reaction is transferred to a low molecular mass propellant (such as hydrogen). Hot propellant is expanded through a nozzle to generate thrust. Development of ceramic metal (cermet) fuel systems for NTP applications is currently ongoing at MSFC. In cermet fuel systems, ceramic fissile fuel particles such as uranium nitride or uranium dioxide are dispersed within a net-shaped, high-density structural matrix. The composite material is cladded by a protective metal structure to make up an NTP fuel element. Cladding materials must be able to withstand the demanding operating conditions required of the engine as well as retain a hermetic seal to allow for retention of fuel element structural integrity, prevent hydrogen attack or migration of the ceramic fuel, and limit release of fission products during operation. For NTP applications, tungsten is a prime material for both the metal matrix and cladding in cermet fuel systems because of its high melting point, high temperature strength, and compatibility with hot hydrogen. If a weld in tungsten with the capability of holding a hermetic seal is achievable, tungsten becomes a strong candidate for NTP applications. This Technical Memorandum focuses on determining the weldability of pure tungsten using electron beam welding (EBW). Tungsten appears well suited for NTP applications, but it has a high ductile to brittle transition temperature (DBTT) dependent upon chemical composition, structure/stress distribution, and mechanical conditions. Therefore, it is highly subject to brittle fracture. Because of its high susceptibility to brittle fracture, it is very difficult to weld. EBW was chosen for joining pure tungsten because of its low heat input compared to gas tungsten arc welding. Reduced heat input can be directly correlated with an increase in ductility of a tungsten weld. EBW is a high energy density welding process in which a stream of electrons penetrates a weld joint in a deep, narrow spike in contrast to a broad gas tungsten arc weld pool. The investigation initially focused on EBW of tungsten plates of both 0.01 in and 0.03 in thickness to determine if EBW could weld pure tungsten without the presence of visual defects—particularly cracking—in the welds. Variation in the weld procedure and post-weld heat treatment (PWHT) was used to improve the surface appearance of flat EBWs on a pure tungsten sheet. The investigation moved on to weld 0.05-in-thick hexagonal tungsten cans with a weld joint thickness of 0.025 in. The goal for welding the pure tungsten hex cans was to avoid any visual surface defects and generate a weld capable of a hermetic seal. This proved difficult. Cold welds commonly exhibited porosity that leaked air. Hot welds exhibited cracks, typically observed immediately after welding. Later welds were preheated to increase ductility and decrease the likelihood of through-thickness cracking. PWHT was used to arrest microcrack growth both in the flat weld samples and hexagonal weld samples.

Courtright, Z. S.↗
NASA NTRS2009

Control-Relevant Modeling, Analysis, and Design for Scramjet-Powered Hypersonic Vehicles

Within this paper, control-relevant vehicle design concepts are examined using a widely used 3 DOF (plus flexibility) nonlinear model for the longitudinal dynamics of a generic carrot-shaped scramjet powered hypersonic vehicle. Trade studies associated with vehicle/engine parameters are examined. The impact of parameters on control-relevant static properties (e.g. level-flight trimmable region, trim controls, AOA, thrust margin) and dynamic properties (e.g. instability and right half plane zero associated with flight path angle) are examined. Specific parameters considered include: inlet height, diffuser area ratio, lower forebody compression ramp inclination angle, engine location, center of gravity, and mass. Vehicle optimizations is also examined. Both static and dynamic considerations are addressed. The gap-metric optimized vehicle is obtained to illustrate how this control-centric concept can be used to "reduce" scheduling requirements for the final control system. A classic inner-outer loop control architecture and methodology is used to shed light on how specific vehicle/engine design parameter selections impact control system design. In short, the work represents an important first step toward revealing fundamental tradeoffs and systematically treating control-relevant vehicle design.

Rodriguez, Armando A.↗
NASA NTRS2016

Engineering Design Tools for Shape Memory Alloy Actuators: CASMART Collaborative Best Practices and Case Studies

The primary goal of the Consortium for the Advancement of Shape Memory Alloy Research and Technology (CASMART) is to enable the design of revolutionary applications based on shape memory alloy (SMA) technology. In order to help realize this goal and reduce the development time and required experience for the fabrication of SMA actuation systems, several modeling tools have been developed for common actuator types and are discussed herein along with case studies, which highlight the capabilities and limitations of these tools. Due to their ability to sustain high stresses and recover large deformations, SMAs have many potential applications as reliable, lightweight, solid-state actuators. Their advantage over classical actuators can also be further improved when the actuator geometry is modified to fit the specific application. In this paper, three common actuator designs are studied: wires, which are lightweight, low-profile, and easily implemented; springs, which offer actuation strokes upwards of 200 at reduced mechanical loads; and torque tubes, which can provide large actuation forces in small volumes and develop a repeatable zero-load actuation response (known as the two-way shape memory effect). The modeling frameworks, which have been implemented in the design tools, are developed for each of these frequently used SMA actuator types. In order to demonstrate the versatility and flexibility of the presented design tools, as well as validate their modeling framework, several design challenges were completed. These case studies include the design and development of an active hinge for the deployment of a solar array or foldable space structure, an adaptive solar array deployment and positioning system, a passive air temperature controller for regulation flow temperatures inside of a jet engine, and a redesign of the Corvette active hatch, which allows for pressure equalization of the car interior. For each of the presented case studies, a prototype or proof-of-concept was fabricated and the experimental results and lessons learned are discussed. This analysis presents a collection of CASMART collaborative best practices in order to allow readers to utilize the available design tools and understand their modeling principles. These design tools, which are based on engineering models, can provide first-order optimal designs and are a basic and efficient method for either demonstrating design feasibility or refining design parameters. Although the design and integration of an SMA-based actuation system always requires application- and environment-specific engineering considerations, common modeling tools can significantly reduce the investment required for actuation system development and provide valuable engineering insight.

Design tools↗
NASA NTRS1986

Czochralski growth of crystals - Simple models for growth rate and interface shape

A simple model for the crystal growth by the Czochralski (CZ) process has been proposed based on semiquantitative arguments. The model provides empirical relationships for the dependence of the pulling rate and the interface shape on the important process variables such as crystal radius, crucible temperature, height of the melt level, and the height of the exposed portion of the crucible wall. The parameters of the model can be evaluated by matching the results obtained from a detailed mathematical model of the CZ process or from extensive experimental data. The model has, therefore, the potential application for determining the best process conditions and for on-line control and optimization of the crystal puller to grow crystals with constant diameter and nearly planar interface.

Srivastava, R. K.↗
NASA NTRS2012

Deriving Plasma Densities and Elemental Abundances from SERTS Differential Emission Measure Analysis

We use high-resolution spectral emission line data obtained by the SERTS instrument during three rocket flights to demonstrate a new approach for constraining electron densities of solar active region plasma.We apply differential emission measure (DEM) forward-fitting techniques to characterize the multithermal solar plasma producing the observed EUV spectra, with constraints on the high-temperature plasma from the Yohkoh Soft X-ray Telescope. In this iterative process, we compare line intensities predicted by an input source distribution to observed line intensities for multiple iron ion species, and search a broad range of densities to optimize chi-square simultaneously for the many available density-sensitive lines. This produces a density weighted by the DEM, which appears to be useful for characterizing the bulk of the emitting plasma over a significant range of temperature. This "DEM-weighted density" technique is complementary to the use of density-sensitive line ratios and less affected by uncertainties in atomic data and ionization fraction for any specific line. Once the DEM shape and the DEM-weighted density have been established from the iron lines, the relative elemental abundances can be determined for other lines in the spectrum. We have also identified spectral lines in the SERTS wavelength range that may be problematic

corona↗
NASA NTRS2018

Polarization-Controlled Directional Multiphoton Photoemission from Hot Spots on Single Au Nanoshells

Directional photoemission from single Au nanoshells is demonstrated in the low-intensity, multiphoton regime. Thisdirectionality is shown to be due to the plasmonic excitation of highly photoemissive, nanometer scale surface regions, which are characterized by correlated momentum mapping, scanning electron microscopy (SEM), and laser polarization-dependence studies. Furthermore, the photoelectron flux from a single nanoshell can be systematically rotated by over 90° in momentum space simply by polarization-controlled coupling to different hot spots. Photoelectrondistributions are directly characterized in momentum space via velocity map imaging (VMI) of the two-dimensional transverse (px, py) momentum components for single nanoshells. For the majority of nanoshells studied, the photoemission is directionally orthogonal to the laser polarization, which implicates nanoscale crevice-shaped "hotspots" clearly observed in the correlated SEM/VMI studies, with the near-field plasmonic nature of these crevices clarified further via finite-element simulations. These results rationalize the large photoemission enhancements observed in previous Au nanoshell studies, but more importantly provide a novel experimental access to directionally tunable electron emission from nanoscale sources. The ability to control photoemission/photocurrent angular distributions at the nanoscale with only modest optical fields indicates a new parameter for optimizing nanoplasmonic system performance and suggests new plasmonic applications such as ultrafast, polarization-controlled photoelectric/photovoltaic switches.

Pettine, Jacob↗
NASA NTRS2010

An Interactive Preliminary Design System of High Speed Forebody and Inlet Flows

This paper demonstrates a simulation-based aerodynamic design process of high speed inlet. A genetic algorithm is integrated into the design process to facilitate the single objective optimization. The objective function is the total pressure recovery and is obtained by using a PNS solver for its computing efficiency. The system developed uses existing software of geometry definition, mesh generation and CFD analysis. The process which produces increasingly desirable design in each genetic evolution over many generations is automatically carried out. A generic two-dimensional inlet is created as a showcase to demonstrate the capabilities of this tool. A parameterized study of geometric shape and size of the showcase is also presented.

Liou, May-Fun↗
NASA NTRS2013

Circularly Polarized Microwave Antenna Element with Very Low Off-Axis Cross-Polarization

The goal of this work was to improve off-axis cross-polarization performance and ease of assembly of a circularly polarized microwave antenna element. To ease assembly, the initial design requirement of Hexweb support for the internal circuit part, as well as the radiating disks, was eliminated. There is a need for different plating techniques to improve soldering. It was also desirable to change the design to eliminate soldering as well as the need to use the Hexweb support. Thus, a technique was developed to build the feed without using solder, solving the lathing and soldering issue. Internal parts were strengthened by adding curvature to eliminate Hexweb support, and in the process, the new geometries of the internal parts opened the way for improving the off-axis cross-polarization performance as well. The radiating disks curvatures were increased for increased strength, but it was found that this also improved crosspolarization. Optimization of the curvatures leads to very low off-axis cross-polarization. The feed circuit was curved into a cylinder for improved strength, eliminating Hexweb support. An aperture coupling feed mechanism eliminated the need for feed pins to the disks, which would have required soldering. The aperture coupling technique also improves cross-polarization performance by effectively exciting the radiating disks very close to the antenna s central axis of symmetry. Because of the shape of the parts, it allowed for an all-aluminum design bolted together and assembled with no solder needed. The advantage of a solderless design is that the reliability is higher, with no single-point failure (solder), and no need for special plating techniques in order to solder the unit together. The shapes (curved or round) make for a more robust build without extra support materials, as well as improved offaxis cross-polarization.

Greem. David↗
NASA NTRS1980

Trajectories optimization in hypersonic flight

Equations of motion were derived for the three dimensional flight of a lifting vehicles, taking into consideration all the main effects of different forces acting on a vehicle at orbital speeds. A set of equations was formulated which are valid for both the flight with lift modulation inside a planetary atmosphere and the Keplerian motion in the vacuum. The equations are independent of the physical characteristics of the vehicle. The only parameters involved are the maximum lift to drag ratio of the vehicle and a constant characterizing the atmosphere. The results obtained can be applied without modifications to any future reentry vehicle, regardless of its size, shape, and mass.

Vinh, N. X.↗
NASA NTRS1980

Development of a vortex-lift-design method and application to a slender maneuver-wing configuration

A method has been developed to optimize the mean camber surface of a cranked slender wing having leading-edge vortex flow at transonic-maneuver conditions using the suction analogy. This type of flow was assumed because it was anticipated that the slenderness of the wing would preclude attached flow at the required lift coefficient. A constraint was imposed in that the camber deflections were to be restricted by a realistic structural-box requirement. The resulting application yielded mean-camber shapes which produced effective suction levels equivalent to 77 percent of the full-planar leading-edge value at the design lift coefficient.

Lamar, J. E.↗