Search NASA⌕ Search

SEARCH · Search NASA

Results for “structural modulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Laser Heated Oxide Fiber Growth Using Melt Modulation Technique

As a reinforcement for structural composites, single crystal alumina fibers offer low density, high modulus, and high creep resistance. In this study, the laser heated float zone approach was employed to grow c-axis Al2O3 continuous fibers of high purity and high strength. A new melt modulation technique, laser scanning, avoids the formation of surface induced ripples and allows the growth of 50 micro-m diameter sapphire fibers with strengths (approx. 7 GPa) significantly greater than either commercially available fibers grown by the edge-defined film growth process (approx. 2-3 GPa) or laboratory fibers grown by stationary laser heating (approx. 5 GPa). The present work suggests that surface striations are the predominant defects controlling the tensile strength of laser-scanned fibers at room temperature. Several possible mechanisms for inducing surface striations are systematically discussed for several oxide fiber compositions.

Sayir, Ali↗

Control-structure interaction study for the Space Station solar dynamic power module

The authors investigate the feasibility of using a conventional PID (proportional plus integral plus derivative) controller design to perform the pointing and tracking functions for the Space Station Freedom solar dynamic power module. Using this simple controller design, the control/structure interaction effects were also studied without assuming frequency bandwidth separation. From the results, the feasibility of a simple solar dynamic control solution with a reduced-order model, which satisfies the basic system pointing and stability requirements, is suggested. However, the conventional control design approach is shown to be very much influenced by the order of reduction of the plant model, i.e., the number of the retained elastic modes from the full-order model. This suggests that, for complex large space structures, such as the Space Station Freedom solar dynamic, the conventional control system design methods may not be adequate.

Cheng, J.↗

Mechanism of allosteric inhibition of human p97/VCP ATPase and its disease mutant by triazole inhibitors

Human p97 ATPase is crucial in various cellular processes, making it a target for inhibitors to treat cancers, neurological, and infectious diseases. Triazole allosteric p97 inhibitors have been demonstrated to match the efficacy of CB-5083, an ATP-competitive inhibitor, in cellular models. However, the mechanism is not well understood. This study systematically investigates the structures of new triazole inhibitors bound to both wild-type and disease mutant forms of p97 and measures their effects on function. These inhibitors bind at the interface of the D1 and D2 domains of each p97 subunit, shifting surrounding helices and altering the loop structures near the C-terminal α2 G helix to modulate domain-domain communications. A key structural moiety of the inhibitor affects the rotameric conformations of interacting side chains, indirectly modulating the N-terminal domain conformation in p97 R155H mutant. The differential effects of inhibitor binding to wild-type and mutant p97 provide insights into drug design with enhanced specificity, particularly for oncology applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Biogenesis of non-structural protein 1 (nsp1) and nsp1-mediated type I interferon modulation in arteriviruses

Type I interferons (IFNs-α/β) play a key role for the antiviral state of host, and the porcine arterivirus; porcine reproductive and respiratory syndrome virus (PRRSV), has been shown to down-regulate the production of IFNs during infection. Non-structural protein (nsp) 1 of PRRSV has been identified as a viral IFN antagonist, and the nsp1α subunit of nsp1 has been shown to degrade the CREB-binding protein (CBP) and to inhibit the formation of enhanceosome thus resulting in the suppression of IFN production. The study was expanded to other member viruses in the family Arteriviridae: equine arteritis virus (EAV), murine lactate dehydrogenase-elevating virus (LDV), and simian hemorrhagic fever virus (SHFV). While PRRSV–nsp1 and LDV–nsp1 were auto-cleaved to produce the nsp1α and nsp1β subunits, EAV–nsp1 remained uncleaved. SHFV–nsp1 was initially predicted to be cleaved to generate three subunits (nsp1α, nsp1β, and nsp1γ), but only two subunits were generated as SHFV–nsp1αβ and SHFV–nsp1γ. The papain-like cysteine protease (PLP) 1α motif in nsp1α remained inactive for SHFV, and only the PLP1β motif of nsp1β was functional to generate SHFV–nsp1γ subunit. All subunits of arterivirus nsp1 were localized in the both nucleus and cytoplasm, but PRRSV–nsp1β, LDV–nsp1β, EAV–nsp1, and SHFV–nsp1γ were predominantly found in the nucleus. All subunits of arterivirus nsp1 contained the IFN suppressive activity and inhibited both interferon regulatory factor 3 (IRF3) and NF-κB mediated IFN promoter activities. Similar to PRRSV–nsp1α, CBP degradation was evident in cells expressing LDV–nsp1α and SHFV–nsp1γ, but no such degradation was observed for EAV–nsp1. Regardless of CBP degradation, all subunits of arterivirus nsp1 suppressed the IFN-sensitive response element (ISRE)-promoter activities. Our data show that the nsp1-mediated IFN modulation is a common strategy for all arteriviruses but their mechanism of action may differ from each other. - Highlights: • LDV–nsp1 was cleaved to nsp1α and nsp1β whereas EAV–nsp1 was uncleaved. • SHFV–nsp1 was cleaved to nsp1αβ and nsp1γ. • PRRSV–nsp1β, LDV–nsp1β, EAV–nsp1, and SHFV–nsp1γ were nuclear proteins. • PRRSV–nsp1α, LDV–nsp1α, and SHFV–nsp1γ caused CBP degradation. • All nsp1 subunits contained interferon and ISRE suppressive activities.

60 APPLIED LIFE SCIENCES↗

Structure and mechanical properties of improved cast stainless steels for nuclear applications

Casting of stainless steels is a promising and cost saving way of directly producing large and complex structures, such a shield modules or divertors for the ITER. Here, a series of modified high-nitrogen cast steels has been developed and characterized. The steels, based on the cast equivalent of 316 composition, have increased N (0.14-0.36%) and Mn (2-5.1%) content; copper was added to one of the heats. Mechanical tests were conducted with non-irradiated and neutron irradiated specimens at 0.7 dpa. It was established that alloying by nitrogen significantly improves the yield stress of non-irradiated steels and the deformation hardening rate. Manganese tended to decrease yield stress, but increased radiation hardening. Furthermore, the role of copper on mechanical properties was negligibly small. Analysis of structure was conducted using SEM-EDS and the nature and compositions of the second phases and inclusions were analyzed in detail. We show that the modified steels, compared to reference material, exhibit significantly reduced elemental inhomogeneity and second phase formation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanistic Insights into Defect-Mediated Crystallization Revealed by Lattice Strain Evolution

Structural defects and lattice strain are intrinsic to many crystalline materials, yet their roles in controlling chemical reaction mechanisms and directing crystallization pathways remain poorly understood. Here, in this study, we revealed the three-dimensional evolution of strain and dislocation defects at the nanoscale during the growth of heterogeneously nucleated barite (BaSO 4 ) and calcite (CaCO 3 ) crystals by using coherent X-ray scattering, electron microscopy, and molecular simulations. Unlike barite, which formed with minimal internal strain, calcite developed dislocation defects and exhibited spatially varying strain that increased during growth. During growth in Sr-rich solutions, calcite likely incorporates Sr 2+ into the defects, which further modulates the local lattice structure and increases both the compressive and tensile strain. These findings suggest that calcite crystallization was likely dominated by attachment of precursor phases, which gave rise to defect-enriched domain structures not predicted by classical growth models. By linking defect formation to ion incorporation and growth dynamics, this work provides fundamental insight into how lattice-level strain heterogeneity governs the chemical reactivity of ionic crystals.

Bragg coherent diffractive imaging↗

Type I Collagen and Collagen Mimetics as Angiogenesis Promoting Superpolymers

Angiogenesis, the development of blood vessels from the pre-existing vasculature, is a key component of embryogenesis and tissue regeneration. Angiogenesis also drives pathologies such as tumor growth and metastasis, and hemangioma development in newborns. On the other hand, promotion of angiogenesis is needed in tissues with vascular insufficiencies, and in bioengineering, to endow tissue substitutes with appropriate microvasculatures. Therefore, much research has focused on defining mechanisms of angiogenesis, and identifying pro- and anti-angiogenic molecules. Type I collagen, the most abundant protein in humans, potently stimulates angiogenesis in vitro and in vivo. Crucial to its angiogenic activity appears to be ligation and possibly clustering of endothelial cell (EC) surface {alpha}1{beta}1/{alpha}2{beta}1 integrin receptors by the GFPGER502-507 sequence of the collagen fibril. However, additional aspects of collagen structure and function that may modulate its angiogenic properties are discussed. Moreover, type I collagen and fibrin, another angiogenic polymer, share several structural features. These observations suggest strategies for creating 'angiogenic superpolymers', including: modifying type I collagen to influence its biological half-life, immunogenicity, and integrin binding capacity; genetically engineering fibrillar collagens to include additional integrin binding sites or angiogenic determinants, and remove unnecessary or deleterious sequences without compromising fibril integrity; and exploring the suitability of poly(ortho ester), PEG-lysine copolymer, tubulin, and cholesteric cuticle as collagen mimetics, and suggesting means of modifying them to display ideal angiogenic properties. The collagenous and collagen mimetic angiogenic superpolymers described here may someday prove useful for many applications in tissue engineering and human medicine.

59 BASIC BIOLOGICAL SCIENCES↗

Strain-engineered growth of two-dimensional materials

The application of strain to semiconductors allows for controlled modification of their band structure. This principle is employed for the manufacturing of devices ranging from high-performance transistors to solid-state lasers. Traditionally, strain is typically achieved via growth on lattice-mismatched substrates. For two-dimensional (2D) semiconductors, this is not feasible as they typically do not interact epitaxially with the substrate. Here in this paper, we demonstrate controlled strain engineering of 2D semiconductors during synthesis by utilizing the thermal coefficient of expansion mismatch between the substrate and semiconductor. Using WSe 2 as a model system, we demonstrate stable built-in strains ranging from 1% tensile to 0.2% compressive on substrates with different thermal coefficient of expansion. Consequently, we observe a dramatic modulation of the band structure, manifested by a strain-driven indirect-to-direct bandgap transition and brightening of the dark exciton in bilayer and monolayer WSe 2 , respectively. The growth method developed here should enable flexibility in design of more sophisticated devices based on 2D materials.

36 MATERIALS SCIENCE↗

Interfacial Hydrogen-Bond Dynamics in Transition Metal Compounds

Understanding how water behaves when confined within atomic layers of active transition-metal carbides, nitrides, and carbonitrides is essential for uncovering the fundamental principles needed to engineer solid–liquid interfaces at the atomic scale. Yet, how lattice element chemistry and surface termination groups collectively regulate the structure and mobility of such interlayer water remains poorly understood. Here, we present a composition-controlled investigation of interlayer water dynamics in layered transition-metal nitride, carbide, and carbonitride systems using a systematic integration of quasi-elastic neutron scattering (QENS), ab initio molecular dynamics (AIMD) simulations, and density functional theory (DFT) calculations. QENS measurements show that nitride-rich systems host mobile, translationally diffusing water with thermally activated self-diffusion coefficients on the order of 10 –10 m 2 s –1 , whereas mixed C/N lattices confine water to localized, nontranslational motion that is insensitive to temperature. AIMD and DFT reveal that lattice C/N chemistry and surface functional group composition reshape the first hydration layer by modulating the surface electronic structure and termination-dependent hydrogen-bond networks, leading to pronounced differences in water ordering and thermal resilience. On the other hand, fully carbide systems exhibit intermediate behavior, highlighting that water mobility is not primarily controlled by the hydration level alone but by the coupling between lattice composition and surface chemistry. Overall, this study establishes how surface chemistry and lattice composition jointly control interfacial hydrogen bond dynamics, offering a mechanistic framework for designing transition-metal layered materials with tailored interfacial transport properties.

Hydration↗

Quantum Confined Stark Effect and Temperature Dependencies of Photoluminescence of InAs Quantum Dots Coupled with AlGaAs/GaAs Two Dimensional Electron Gas

In this work, Experimental study of the influence of internal electric field and the temperature on the photoluminescence of InAs self assembled quantum dots inserted in AlGaAs/GaAs modulation doped hetero-structure have been investigated. The internal electric field is controlled by an appropriate design of the hetero-structure. We have observed a red shift of the photoluminescence position peaks result from the quantum confined Stark effect due to the local electric field existing in the structure. Estimation values of the internal electric field have been obtained through carrier’s densities values in interface of AlGaAs/GaAs hetero-junction. An anomalous dependence of the full width at half maximum with temperature has been found, which attributed to the carrier’s dynamics between InAs quantum dots layer and the two-dimensional electron gas.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nonlinear Fano-Resonant Dielectric Metasurfaces

Strong nonlinear light matter interaction is highly sought-after for a variety of applications including lasing and all-optical light modulation. Recently, resonant plasmonic structures have been considered promising candidates for enhancing nonlinear optical processes due to their ability to greatly enhance the optical near-field; however, their small mode volumes prevent the inherently large nonlinear susceptibility of the metal from being efficiently exploited. We present an alternative approach that utilizes a Fano-resonant silicon metasurface. The metasurface results in strong near-field enhancement within the volume of the silicon resonator while minimizing two photon absorption. Here, we measure a third harmonic generation enhancement factor of 1.5 105 with respect to an unpatterned silicon film and an absolute conversion efficiency of 1.2 10 6 with a peak pump intensity of 3.2 GW cm 2. The enhanced nonlinearity, combined with a sharp linear transmittance spectrum, results in transmission modulation with a modulation depth of 36%. Finally, the modulation mechanism is studied by pump probe experiments

36 MATERIALS SCIENCE↗

Compositional dependence of disordered structures in Na½Bi½TiO3-BaTiO3 solid solutions

Highlights: • Diffuse X-ray scattering collected from 4 compositions of Na{sub ½}Bi{sub ½}TiO{sub 3}-x%BaTiO{sub 3}. • Oxygen octahedral tilts, atomic displacements and modulations existed. • All local disordered structures evolved across the morphotropic phase boundary. - Abstract: Disordered structures contribute to the relaxor ferroelectric properties of the lead-free system Na{sub ½}Bi{sub ½}TiO{sub 3}-(x)%BaTiO{sub 3}. Such structures are difficult to characterize with conventional structural analysis techniques. Here, diffuse X-ray scattering was used to analyze the disordered structures from four single-crystals of Na{sub ½}Bi{sub ½}TiO{sub 3}-(x)%BaTiO{sub 3}, with compositions of (x)% = 0%, 4%, 9% and 17%. Such a range of compositions allowed a distinction between the structures that occur across the morphotropic phase boundary, where enhanced electro-mechanical properties have been reported. Throughout the compositional range, the resulting diffuse scattering showed the modification of correlated atomic displacements, transformation of planar defects in the oxygen octahedral tilt-systems, and the presence of modulations of approximately 10 unit cells. The results reported here demonstrate an evolution of the short-range structures across the morphotropic phase boundary that may underpin the electro-mechanical properties of Na{sub ½}Bi{sub ½}TiO{sub 3}-(x)%BaTiO{sub 3}. This information will ultimately assist in tailoring disordered structures for next-generation piezoelectric materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DEPRECATED JacketSE (WISDEM®) [SWR-14-23]

THIS REPOSITORY IS DEPRECATED AND WAS ARCHIVED (READ-ONLY) on June 19, 2020. WISDEM has moved to a single, integrated repository at https://github.com/orgs/NLRWindSystems/repositories JacketSE is a DEPRECATED systems engineering model for 3 and 4-legged lattice structures (jackets) supporting tubular steel towers for offshore wind turbines. A module for static hydrodynamic, aerodynamic, and structural design and analysis of wind turbine jacket and towers within the Systems Engineering toolbox.

Damiani, Rick↗

Investigation of high hole mobility In{sub 0.41}Ga{sub 0.59}Sb/Al{sub 0.91}Ga{sub 0.09}Sb quantum well structures grown by molecular beam epitaxy

Modulation-doped In{sub 0.41}Ga{sub 0.59}Sb/Al{sub 0.91}Ga{sub 0.09}Sb quantum-well (QW) structures were grown by molecular beam epitaxy. Cross-sectional transmission electron microscopy and atomic force microscopy studies show high crystalline quality and smooth surface morphology. X-ray diffraction investigations confirm 1.94% compressive strain within In{sub 0.41}Ga{sub 0.59}Sb channel. High room temperature hole mobility with high sheet density of 1000 cm{sup 2}/Vs, 0.877 × 10{sup 12}/cm{sup 2}, and 965 cm{sup 2}/Vs, 1.112 × 10{sup 12}/cm{sup 2} were obtained with different doping concentrations. Temperature dependent Hall measurements show different scattering mechanisms on hole mobility at different temperature range. The sheet hole density keeps almost constantly from 300 K to 77 K. This study shows great potential of In{sub 0.41}Ga{sub 0.59}Sb/Al{sub 0.91}Ga{sub 0.09}Sb QW for high-hole-mobility device applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Application of OpenFOAM to Plume Impingement in Space Environments

After 30 years of continuous human presence in low-earth orbit, NASA is returning to the moon and eventually will go to Mars. Travelling beyond low earth orbit requires NASA to learn how humans can live in Deep Space environments – beyond the protection of Earth’s magnetosphere and at distances from Earth that prevent a quick return in case of trouble. To this end, NASA is constructing the Lunar Gateway, an ISS-like space station to be put in orbit around the moon to act as a home base for Lunar exploration for NASA astronauts. The Gateway Lunar outpost will be built incrementally, via modules which will arrive at separate times and dock to the existing structure. The incremental addition of Gateway modules, and the docking of visiting vehicles, is achieved via a sequence of firings from the approaching body’s onboard reaction control system (RCS) thrusters to achieve the required approach trajectory. The typical hypergolic chemical RCS thrusters work by firing hot gases to produce adverse thrust and the needed change in velocity to safely finish the docking process. The exhaust gas from the RCS thrusters form plumes that expand into the vacuum of space and can impinge onto the outer surfaces of the Lunar Gateway, causing unwanted forces and moments, heat loads, sediment deposition, and in extreme cases, even surface erosion - all mechanisms that can damage the Lunar Gateway and must be minimized. Both permanent and visiting modules will have this RCS thruster exhaust impingement problem. This research aims to establish existing OpenFOAM solvers as a methodology for improving simulation techniques of rocket exhaust plume impingement in space environments. The flow structure of a plume in a space environment is complex; a plume that originates from a hypergolic chemical RCS thruster and expands into a vacuum will experience several regimes of rarefication. This range includes the continuum flow in the rocket nozzle through the fully rarefied free molecular flow further from the nozzle. The flow physics is different at these two extremes, and as such, the simulation approach for plumes is generally divided into a traditional computational fluid dynamics (CFD) simulation in and near the nozzle which is coupled to a subsequent direct simulation Monte Carlo (DSMC) simulation. At this time, the scope of this research is developing, verifying, and validating a method using existing solvers in the OpenFOAM framework for performing coupled CFD/DSMC calculations to determine the extent of plume impingement loading on generic space structures. This presentation will detail code-to-code comparisons between the hyStrath dsmcFoam+ solver, developed using OpenFOAM and available as open-source, and NASA’s in-house DSMC Analysis Code (DAC). Comparisons to several open-source publication findings using DAC [3,4] are presented, and advantages of using an OpenFOAM based solver are also discussed. The presentation concludes with a discussion of future work, and a plan for coupling the dsmcFoam+ solver with CFD simulations of chemical rocket engines for unified coupled plume simulation.

DSMC↗

Pore space partition of metal-organic frameworks for gas storage and separation

Pore space partition (PSP) concept is a synthetic design concept and can also serve as a structure analysis method useful for next-step synthetic planning and execution. PSP provides an integrated chemistry-topology-focused tool to design new materials platforms. While PSP is no less effective for making large-pore materials, the growing importance of small-molecule gas storage and separation for green-energy applications provides impetus for developing small-pore materials for which the PSP strategy is uniquely suited. Currently, the best embodiment of the PSP concept is the partitioned-acs (pacs) platform in which both fine or coarse adjustments to the building blocks have sparked a transformation of a prototype framework into a huge and continuously expanding family of chemically robust materials with controllable pore metrics and functionalities suitable for tailored applications. The pacs compositional diversity results from the platform’s intrinsic multi-module nature, geometric flexibility and tolerance towards individual module variations, and mutual structure-directing effects among various modules, all of which combine to enable the molecular-level uniform co-assemblies of chemical components rarely seen together elsewhere. Here, in this contribution, we present an overview of different pore space engineering methods and how different MOF materials have contributed to important advances in chemical stability, industrial gas storage and gas separation. In particular, we will focus on synthetic assembly of the pacs system, highlighting the differences of pacs materials from other MOF platforms and advantages of pacs materials in enhancing various MOF properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modular structure of highly ordered eudialyte and its place among hydrated minerals of rastsvetaevite family

The crystal structure of a representative of eudialyte group, which was found by A.P. Khomyakov at the Rasvumchorr mountain of the Khibiny alkaline massif (Kola Peninsula), has been studied by X-ray diffraction. The trigonal unit-cell parameters are found to be a = 14.2328(5) Å, c = 60.217(2) Å, V = 10564.08(3) Å3, sp. gr. R3m. The structure has been refined with the isotropic and anisotropic approximation displacement parameters to the total reliability factor R = 5.6%, based on 2989 reflections with |F| > 4σ(F). The idealized formula (Z = 3) is determined as [(H{sub 3}O){sub 11}Na{sub 10}K5]Cа{sub 12}(Na{sub 3}Fe{sub 2}Mn)Si{sub 4}Zr{sub 6}(Si{sub 48}O{sub 144})(OH,Cl){sub 5}(H{sub 2}O){sub 5}. The unit cell of the mineral is doubled due to the presence of two modules of different composition and structure in it (alluaivite-and kentbrooksite-like ones) and the formation of a polyhedral cluster in the kentbrooksite module. A comparison with two hydrated minerals having a modular structure shows that these minerals, being similar in their chemical composition, differ in the cation ordering over the sites of the two modules. The sample under study contains potassium in only one module, while oxonium groups are distributed in both modules but over different sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Spectrally Selective Mirrors with Combined Optical and Thermal Benefit for Photovoltaic Module Thermal Management

Waste heat generated during daytime operation of a solar module will raise its temperature and reduce cell efficiency. In addition to thermalization and carrier recombination, one major source of excess heat in modules is the parasitic absorption of light with sub-bandgap energy. Parasitic absorption can be prevented if sub-bandgap radiation is reflected away from the module. We report on the design considerations and projected changes to module energy yield for photonic reflectors capable of reflecting a portion of sub-bandgap radiation while maintaining or improving transmission of light with energy greater than the semiconductor bandgap. Using a previously developed, self-consistent opto-electro-thermal finite-element simulation, we calculate the total additional energy generated by a module, including various photonic reflectors, and decompose these benefits into thermal and optical effects. We show that the greatest total energy yield improvement comes from photonic mirrors designed for the outside of the glass, but that mirrors placed between the glass and the encapsulant can have significant thermal benefit. We then show that optimal photonic mirror design requires consideration of all angles of incidence, despite unequal amounts of radiation arriving at each angle. We find that optimized photonic mirrors will be omnidirectional in the sense that they have beneficial performance, regardless of the angle of incidence of radiation. By fulfilling these criteria, photonic mirrors can be used at different geographic locations or different tilt angles than their original optimization conditions with only marginal changes in performance. We show designs that improve energy output in Golden, Colorado by 3.7% over a full year. This work demonstrates the importance of considering real-world irradiance and weather conditions when designing optical structures for solar applications.

14 SOLAR ENERGY↗