Search NASA⌕ Search

SEARCH · Search NASA

Results for “substructuring”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Orientation gradients in relation to grain boundaries at varying strain level and spatial resolution

The resolution dependence of orientation gradients was studied in a well-annealed 99.9995% pure polycrystalline copper pulled to failure in tension. Owing to the well developed neck, different regions in the sample correspond to different tensile strains. Post-mortem characterization was performed using EBSD on cross-sections containing the tensile axis. Kernel average misorientation (KAM) was calculated as a metric to establish correlation between defect accumulation and microstructural features, with a threshold of 5° to focus on intra-granular gradients. The region with the lowest strain (2%) showed high KAM values adjacent to grain boundaries compared to the grain interior, regardless of the point spacing, i.e. the spatial resolution. However, in the region with the highest strain (13%) a strong dependence on resolution was found. For point spacings of 0.5 μm or smaller, the same correlation of high KAM with locations near boundaries was found. At coarse spacings i.e. low spatial resolution, by contrast, the reverse was found in that the highest KAM values appear in the grain interiors, as previously observed in X-ray microscopy on the same sample which had a similar coarse resolution. An analysis of orientation gradients parallel to, and perpendicular to boundaries suggested that the latter tend to be the larger of the two. This helps to explain why boundary-adjacent points have low KAM values. The conclusion is that measurement of local orientation gradient requires a resolution that is comparable to the dislocation substructure.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Microstructures and mechanical properties of compositionally complex Co-free FeNiMnCr 18 FCC solid solution alloy

Recently, a structurally-simple but compositionally-complex FeNiCoMnCr high entropy alloy was found to have excellent mechanical properties (e.g., high strength and ductility). To understand the potential of using high entropy alloys as structural materials for advanced nuclear reactor and power plants, it is necessary to have a thorough understanding of their structural stability and mechanical properties degradation under neutron irradiation. Furthermore, this requires us to develop a similar model alloy without Co because material with Co will make post-neutron-irradiation testing difficult due to the production of the 60 Co radioisotope. In order to achieve this goal, a FCC-structured single-phase alloy with a composition of FeNiMnCr 18 was successfully developed. This near-equiatomic FeNiMnCr 18 alloy has good malleability and its microstructure can be controlled by thermomechanical processing. By rolling and annealing, the as-cast elongated-grained-microstructure is replaced by homogeneous equiaxed grains. The mechanical properties (e.g., strength and ductility) of the FeNiMnCr 18 alloy are comparable to those of the equiatomic FeNiCoMnCr high entropy alloy. Both strength and ductility increase with decreasing deformation temperature, with the largest difference occurring between 293 and 77 K. Extensive twin-bands which are bundles of numerous individual twins are observed when it is tensile-fractured at 77 K. No twin bands are detected by EBSD for materials deformed at 293 K and higher. Ultimately the unusual temperature-dependencies of UTS and uniform elongation could be caused by the development of the dense twin substructure, twin-dislocation interactions and the interactions between primary and secondary twinning systems which result in a microstructure refinement and hence cause enhanced strain hardening and postponed necking.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Sensitivity of polycrystal plasticity to slip system kinematic hardening laws for Al 7075-T6

The prediction of formation and early growth of microstructurally small fatigue cracks requires use of constitutive models that accurately estimate local states of stress, strain, and cyclic plastic strain. However, few research efforts have attempted to systematically consider the sensitivity of overall cyclic stress-strain hysteresis and higher order mean stress relaxation and plastic strain ratcheting responses introduced by the slip system back-stress formulation in crystal plasticity, even for face centered cubic (FCC) crystal systems. This paper explores the performance of two slip system level kinematic hardening models using a finite element crystal plasticity implementation as a User Material Subroutine (UMAT) within ABAQUS, with fully implicit numerical integration. The two kinematic hardening formulations aim to reproduce the cyclic deformation of polycrystalline Al 7075-T6 in terms of both macroscopic cyclic stress-strain hysteresis loop shape, as well as ratcheting and mean stress relaxation under strain- or stress-controlled loading with mean strain or stress, respectively. The first formulation is an Armstrong-Frederick type hardening-dynamic recovery law for evolution of the back stress. This approach is capable of reproducing observed deformation under completely reversed uniaxial loading conditions, but overpredicts the rate of cyclic ratcheting and associated mean stress relaxation. The second formulation corresponds to a multiple back stress Ohno-Wang type hardening law with nonlinear dynamic recovery. The adoption of this back stress evolution law greatly improves the capability to model experimental results for polycrystalline specimens subjected to cycling with mean stress or strain. As a result, the relation of such nonlinear dynamic recovery effects are related to slip system interactions with dislocation substructures.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effects of Alloying and Processing Modifications on Precipitation Behavior and Elevated Temperature Strength in 9% Cr Ferritic/Martensitic Steels

Two low-carbon 9-Cr ferritic-martensitic steels were designed here with the aim of decreasing M 23 C 6 and maintaining or increasing MX phase fraction. A low-carbon (LC) alloy and a low-carbon, zero-niobium (0 Nb) alloy were fabricated, their designs based upon the P92 alloy system. Solutionizing temperatures to maximize V and Nb in solution while avoiding δ-ferrite were determined to be 1170 °C for the P92 alloy and 1050 °C for LC and 0 Nb, significantly lower than predicted using ThermoCalc ® modelling. As was intended, the M 23 C 6 phase fraction was reduced for LC and 0 Nb alloys after both heat treating and aging relative to the base P92 alloy, as determined by wide angle x-ray scattering (WAXS) analysis. Dislocation density measurements from x-ray line broadening in P92 and LC suggest these alloys had more stable dislocation substructures than 0 Nb at lower temperature and shorter time aging conditions. While LC exhibited lower microhardness than P92 at room temperature, the tensile properties were comparable at 650 °C, suggesting that elevated temperature strength can be achieved with lower carbon contents. Aging studies showed that P92 had a more stable microstructure for higher temperature and longer time aging conditions. The P92 alloy also had a longer stress rupture life, implying that the M 23 C 6 precipitate contribution to thermal stability is important. Evidence of Z-phase was discovered for the LC alloy aged 10,000 h at 650 °C, corresponding to decreased strength and increased ductility. Overall, the stress rupture lives of the modified heat-treatment variations of P92 and LC compare favorably to literature values for 9% Cr steels with conventional heat treatments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Strain-rate dependent deformation mechanisms in single-layered Cu, Mo, and multilayer Cu/Mo thin films

Here, strain-rate sensitivity and rate-dependent hardness, over a range of 10 -2 to 10 2 s -1 , of sputter-deposited single-layered Cu, Mo, and 5 nm Cu/ 5 nm Mo, and 100 nm Cu/ 100 nm Mo multilayer films with a total film thickness of 5 μm were measured using nanoindentation. The plastic zone underneath the nanoindents was characterized via cross-sectional transmission electron microscopy (XTEM). The multilayer films exhibited enhanced hardness but slightly reduced strain-rate sensitivity with decreasing layer thickness from 100 nm to 5 nm. Only the 5 nm Cu/ 5 nm Mo multilayer film exhibited shear bands underneath the nanoindents, and the size of the shear bands increased with increasing strain rate. In contrast, the 100 nm Cu/ 100 nm Mo multilayer film exhibited material pile-up around the indents and significant nanotwinning within Cu grains. The effect of strain rate and layer thickness on the hardness and strain rate sensitivity of the multilayer thin films is interpreted using a modified confined layer slip (CLS) model. The reduced rate sensitivity at 5 nm as compared to 100 nm correlates with abundant growth nanotwins in the Cu grains in 100 nm and formation of shear bands in 5 nm multilayers. In single layer films, a substructure with a high density of dislocations was observed consistent with the plastic strain gradient in the indent plastic zone. No evidence of deformation twins was noted in any of the samples.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Post-build stress-relief optimization for laser powder bed fusion 316H stainless steel

Nuclear energy remains a critical component of a diversified and efficient energy portfolio, offering reliable, high-capacity, and low-carbon power. However, in the U.S., aging infrastructure and the slow qualification and deployment of advanced materials and manufacturing techniques hinder progress in next-generation reactor technologies. This study explores the application of laser powder bed fusion (LPBF) additive manufacturing for stainless steel 316H, with a focus on optimizing post-build heat treatments to enhance material properties for high-temperature nuclear applications. The research targets the optimization of stress-relief temperatures to alleviate postbuild residual stresses, ensuring improvements in the microstructural corelated properties. A series of microstructural and mechanical evaluations were performed on LPBF-printed SS-316H samples which were subjected to annealing at temperatures varying between 650 °C and 850 °C. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses revealed that increasing the heattreatment temperature accelerated dislocation recovery. Vickers microhardness measurements showed an initial reduction in values, followed by stabilization over extended durations at all the temperatures. While higher temperatures facilitated faster recovery, they also promoted carbide precipitation along grain and solidification cell boundaries, narrowing the safe processing window. In contrast, heat treatment at 650°C preserved the cellular substructure and enabled controlled carbide precipitation over time. In conclusion, these findings highlight the importance of time–temperature optimization and suggest that 650°C for up to 2 h provides the most favorable balance between recovery and carbide control for a stress-relief treatment.

316 stainless steel↗
DOE OSTI2023

Effect of Fermi surface topology change on the Kagome superconductor CeRu 2 under pressure

The cubic Laves phase compound CeRu 2 with a Kagome substructure of Ru has been investigated to understand myriad fascinating phenomena resulting from competition among its various physical and geometric features. Such phenomena include flat bands, van Hove singularities, Dirac cones, reentrant superconductivity, magnetism, the Fulde–Ferrell–Larkin–Ovchinnikov state, valence fluctuations, time-irreversible anisotropic s-state superconductivity, etc. Extensive studies have thus been carried out since 1958 when the highly unusual coexistence of superconductivity and ferromagnetism was proposed for the mixed compounds (Ce,Gd)Ru 2 . Activity has accelerated in recent years due to increasing interest in topological states in superconductors. However, there has been little investigation of the mutual influence of these fascinating states. Therefore, we systematically investigated the superconductivity and possible Fermi surface topological change in CeRu 2 via magnetic, resistivity, and structural measurements under pressure up to ~168 GPa. An unusual phase diagram that suggests an intriguing interplay between the compound’s superconducting order and Fermi surface topological order has been constructed. A resurgence in its superconducting transition temperature was observed above 28 GPa. Our experiments have identified a structural transition above 76 GPa and a few tantalizing phase transitions driven by high pressure. Our high-pressure results further suggest that superconductivity and Fermi surface topology in CeRu 2 are strongly intertwined.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Seismic isolation: A pathway to standardized advanced nuclear reactors

Standardizing advanced nuclear reactors is a pathway to substantially reducing their overnight capital cost and achieving parity with other power sources, including renewables and fossil fuels. The seismic load case has thwarted standardization of nuclear power plants because site-specific seismic hazard and local near-surface geology has triggered soil-structure-interaction analysis, design, equipment qualification, regulatory review, and licensing, ensuring that each build is different. To achieve standardized or site-independent certified advanced reactor designs, the impact of the seismic load case on the engineering and construction cost and time must be substantially mitigated. Seismic isolation is a mature technology that has been used for more than 30 years in non-nuclear sectors to substantially reduce earthquake demands in buildings and other infrastructure. In this paper, seismic isolation is used to enable standardization of advanced reactor designs, aimed at the complete re-use of a site-independent, certified design and repeated procurement of safety-class equipment. A pathway to standardized designs using seismic isolation is demonstrated for two fundamentally different advanced reactors: a molten salt reactor and a high temperature gas reactor. Each reactor building is equipped with three specialized pieces of safety-class equipment, namely, a reactor vessel, a steam generator, and a control rod drive mechanism housing that is attached to the reactor head. Analysis is performed per ASCE and ASME standards to design the buildings and the equipment for two base conditions: conventional (fixed base) and base isolated. The impact of the seismic load case is characterized for the reinforced concrete walls in the buildings and for the equipment, measured using vessel wall thickness and horizontal accelerations. Here the analysis results show that the fixed-base buildings, designed for a site of low seismic hazard (peak ground acceleration, PGA = 0.15 g) could be constructed at a site of much greater seismic hazard (PGA = 0.7 g) if seismic base isolation is employed. Importantly, the scope of the site-specific analysis, design, and qualification would be limited to the seismic isolators and the isolated substructure, drastically reducing plant-specific engineering, review, and licensing, and time to construction start. Regulatory challenges and opportunities with standardized reactor designs are identified.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

QCD factorization and universality of jet cross sections in heavy-ion collisions

In this work, we review a recently proposed phenomenological framework to establish the notions of QCD factorization and universality of jet cross sections in the heavy-ion environment. First results of a global analysis of the nuclear modification factor of inclusive jets are presented where we extract medium modified jet functions using a Monte Carlo sampling approach. We observe that gluon jets are significantly more suppressed than quark jets. In addition, we study the jet radius dependence of the inclusive jet cross section in heavy-ion collisions and comment on a recent measurement from CMS. By considering for example jet substructure observables it will be possible to test the universality of the extracted medium jet functions. We thus expect that the presented results will eventually allow for extractions of medium properties with a reduced model bias.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Directly probing the Higgs-top coupling at high scales

We explore the sensitivity to new physics for the coupling of the Higgs boson (h) and top quark (t) at high energy scales with the process ${pp}$→ $t\bar{t}h$ at the high-luminosity LHC. This process probes the coupling in both the space-like and time-like domains at a high scale, complementary to the off-shell Higgs processes in the time-like domain. The effects from physics beyond the Standard Model are parametrized in terms of the effective field theory framework and a non-local Higgs-top form factor. Focusing on the boosted Higgs regime in association with jet substructure techniques, we show that the present search can directly probe the Higgs-top coupling to good precision, providing a strong sensitivity to the new physics scale

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Search for new particles in an extended Higgs sector with four b quarks in the final state at $\sqrt{s}$ = $\mathrm{13 TeV}$

A search for a massive resonance X decaying to a pair of spin-0 bosons φ that themselves decay to pairs of bottom quarks, is presented. The analysis is restricted to the mass ranges m φ from 25 to 100 GeV and m x from 1 to 3 TeV. For these mass ranges, the decay products of each φ boson are expected to merge into a single large-radius jet. Jet substructure and flavor identification techniques are used to identify these jets. The search is based on CERN LHC proton-proton collision data at $\sqrt{s}$ = 13 TeV, collected with the CMS detector in 2016–2018, corresponding to an integrated luminosity of 138 fb -1 Model-specific limits, where the two new particles arise from an extended Higgs sector, are set on the product of the production cross section and branching fraction for X → φφ → ($b\bar{b}$)($b\bar{b}$) as a function of the resonances' masses, where both the X → φφ → and φ → $b\bar{b}$ branching fractions are assumed to be 100%. These limits are the first of their kind on this process, ranging between 30 and 1fb at 95% confidence level for the considered mass ranges.

2HDM↗
DOE OSTI2024

Measurement of (anti)alpha production in central Pb–Pb collisions at $\sqrt{s_{NN}} = 5.02$ TeV

In this letter, measurements of (anti)alpha production in central (0–10%) Pb–Pb collisions at a center-of-mass energy per nucleon–nucleon pair of $\sqrt{s_{NN}} = 5.02$ TeV are presented, including the first measurement of an antialpha transverse-momentum spectrum. Owing to its large mass, the production of (anti)alpha is expected to be sensitive to different particle production models. The production yields and transverse-momentum spectra of nuclei are of particular interest because they provide a stringent test of these models. The averaged antialpha and alpha spectrum is compared to the spectra of lighter particles, by including it into a common blast-wave fit capturing the hydrodynamic-like flow of all particles. This fit is indicating that the (anti)alpha also participates in the collective expansion of the medium created in the collision. A blast-wave fit including only protons, (anti)alpha, and other light nuclei results in a similar flow velocity as the fit that includes all particles. A similar flow velocity, but a significantly larger kinetic freeze-out temperature is obtained when only protons and light nuclei are included in the fit. The coalescence parameter B 4 is well described by calculations from a statistical hadronization model but significantly underestimated by calculations assuming nucleus formation via coalescence of nucleons. Similarly, the (anti)alpha-to-proton ratio is well described by the statistical hadronization model. On the other hand, coalescence calculations including approaches with different implementations of the (anti)alpha substructure tend to underestimate the data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Medium-induced modification of groomed and ungroomed jet mass and angularities in Pb–Pb collisions at $\sqrt{s_{NN}}$ = 5.02 TeV

The ALICE Collaboration presents a new suite of jet substructure measurements in Pb–Pb and pp collisions at a center-of-mass energy per nucleon pair $\sqrt{s_{NN}}$ = 5.02 TeV. These measurements provide access to the internal structure of jets via the momentum and angle of their constituents, probing how the quark–gluon plasma modifies jets, an effect known as jet quenching. Jet grooming additionally removes soft wide-angle radiation to enhance perturbative accuracy and reduce experimental uncertainties. We report the groomed and ungroomed jet mass m jet and jet angularities λ$^{κ}_{α}$ using κ = 1 and α > 0. Charged-particle jets are reconstructed at midrapidity using the anti-k T algorithm with resolution parameter R = 0.2. A narrowing of the jet mass and angularity distributions in Pb–Pb collisions with respect to pp is observed and is enhanced for groomed results, confirming modification of the jet core. By using consistent jet definitions and kinematic cuts between the mass and angularities for the first time, previous inconsistencies in the interpretation of quenching measurements are resolved, rectifying a hurdle for understanding how jet quenching arises from first principles and highlighting the importance of a well-controlled baseline. These results are compared with a variety of theoretical models of jet quenching, providing constraints on jet energy-loss mechanisms in the quark–gluon plasma.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Symmetric-asymmetric collision comparison: Disentangling nuclear structure and subnucleonic structure effects for small system flow

Previous flow measurements in small collision systems were mostly based on highly asymmetric collisions (p+Pb, p+Au, d+Au, 3 He+Au), where both nuclear structure and subnucleonic fluctuations are important. Comparing these asymmetric systems with the newly available symmetric 16 O+ 16 O collisions at RHIC and LHC provides a unique opportunity to disentangle these two contributions. Using Glauber models incorporating both nucleon and quark-level substructure, we analyze multiplicity distributions and initial-state estimators: eccentricities ε n for anisotropic flow ν n and inverse transverse size d ⟂ for radial flow. We find that subnucleonic fluctuations impact O+O collisions differently from asymmetric systems, creating specific patterns in flow observables that enable disentangling the competing contributions. Such experimental comparisons will reduce uncertainties in the initial conditions and improve our understanding of the properties of the QGP-like medium produced in small systems.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Search for a new heavy resonance decaying to a top quark and a neutral scalar boson in proton-proton collisions at $\sqrt{s}$ = 13 TeV

A first search at the LHC for a new heavy resonance decaying to a top quark and a neutral scalar boson ϕ in the fully hadronic final state is presented, where the ϕ boson is identified by its decay into a bottom quark-antiquark pair. The search is focused on final states in which the decay products of the highly Lorentz boosted top quark and ϕ boson are each reconstructed as a single, large-radius jet with distinct substructure. The analysis is performed using proton-proton collision data at a center-of-mass energy of 13 TeV, corresponding to an integrated luminosity of 138 fb −1 , recorded with the CMS detector at the LHC in 2016–2018. The single production of a vector-like top quark, T′, is used as a benchmark model for the signal process. The results of this search are combined with those of a previous CMS search in which semileptonic decays of the top quark were used. No significant excess of data is observed with respect to the background prediction. For the case where the neutral scalar is a standard model Higgs boson and the T′ quark width is 5% of its mass, T′ quark masses between 0.85 and 1.3 TeV are excluded at 95% confidence level and the most stringent limits to date are set for masses above 2 TeV . For other ϕ boson masses, upper limits as low as 0.1 fb are set on the product of the T′ quark production cross section and branching fraction for its decay to a top quark and a ϕ boson.

Boosted↗
DOE OSTI2017

Dark matter self-interactions and small scale structure

We review theories of dark matter (DM) beyond the collisionless paradigm, known as self-interacting dark matter (SIDM), and their observable implications for astrophysical structure in the Universe. Self-interactions are motivated, in part, due to the potential to explain long-standing (and more recent) small scale structure observations that are in tension with collisionless cold DM (CDM) predictions. Simple particle physics models for SIDM can provide a universal explanation for these observations across a wide range of mass scales spanning dwarf galaxies, low and high surface brightness spiral galaxies, and clusters of galaxies. At the same time, SIDM leaves intact the success of $Λ$CDM cosmology on large scales. This report covers the following topics: (1) small scale structure issues, including the core–cusp problem, the diversity problem for rotation curves, the missing satellites problem, and the too-big-to-fail problem, as well as recent progress in hydrodynamical simulations of galaxy formation; (2) N-body simulations for SIDM, including implications for density profiles, halo shapes, substructure, and the interplay between baryons and self-interactions; (3) semi-analytic Jeans-based methods that provide a complementary approach for connecting particle models with observations; (4) merging systems, such as cluster mergers (e.g., the Bullet Cluster) and minor infalls, along with recent simulation results for mergers; (5) particle physics models, including light mediator models and composite DM models; and (6) complementary probes for SIDM, including indirect and direct detection experiments, particle collider searches, and cosmological observations. In conclusion, we provide a summary and critical look for all current constraints on DM self-interactions and an outline for future directions.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Review and status of tool tip frequency response function prediction using receptance coupling

This paper provides a chronological review of publications that implement and advance the receptance coupling substructure analysis (RCSA) approach first applied to tool tip receptance (or frequency response function) prediction for milling applications in 2000. The review topics mimic the RCSA approach, where the tool, holder, and spindle-machine receptances are coupled analytically, and include: tool-holder receptance modeling; connection modeling; spindle-machine receptances; and applications. The review paper summarizes contributions from multiple, international authors (198 papers) to these topics. Additionally, it provides a comprehensive resource for those beginning an investigation into RCSA.

42 ENGINEERING↗