Search NASA⌕ Search

SEARCH · Search NASA

Results for “Additive Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Additive Manufacturing Fabrication of PEEK Counter-Current Centrifugal Contactor Components

Additive manufacturing (AM, also known as 3D printing) offers significant advantages for the fabrication of annular centrifugal contactor-separator (CCS) stages, particularly when complemented by post-processing via traditional machining. The shortcomings of 3D printing of CCSs are offset by its low cost, quick turnaround, and ability to manufacture enhanced mixing sections and multistage modules. High-density acrylic materials show promise for improved chemical resistance and mechanical properties. The demonstration of the MOEX process using acrylic AM CCS stages confirmed their full functionality and showed significant flexibility in geometry design while using relatively low-cost plastic materials. Over the past two years, AM has been used to produce low-cost centrifugal contactor components, ranging from bench-scale laboratory testing to a full-scale industrial process with on-hand availability of spare parts and great flexibility in design modifications and quick testing and implementation. However, the shortcomings of stereo lithography assembly (SLA)-printed acrylic components became apparent rather quickly. By the completion of the initial MOEX demonstration using the 9-stage 2-cm CCS bank, nearly half of the rotors had begun to fail from pitting and cracking. These problems were most likely caused by swelling of the rotor due to liquid absorption, resulting in improper excess run out, mechanical abrasion, and chemical exposure of the roughened surface. Additional deterioration of the acrylic stages was later discovered when the interiors of the acrylic housings began to experience flaking and delamination as the plastic dried out several weeks after the tests. All of these issues caused severe limitations to the lifespan of the CCS stages, which are acceptable for R&D but undesirable for commercial-scale production.

42 ENGINEERING↗
DOE OSTI2017

Evaluation of Advanced Polymers for Additive Manufacturing

The goal of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Oak Ridge National Laboratory (ORNL) and PPG Industries, Inc. (PPG) was to evaluate the feasibility of using conventional coatings chemistry and technology to build up material layer-by-layer. The PPG-ORNL study successfully demonstrated that polymeric coatings formulations may overcome many limitations of common thermoplastics used in additive manufacturing (AM), allow lightweight nozzle design for material deposition, and increase build rate. The materials effort focused on layer-by-layer deposition of coatings with each layer fusing together. The combination of materials and deposition results in an additively manufactured build that has sufficient mechanical properties to bear the load of additional layers, yet is capable of bonding across the z-layers to improve build direction strength. The formulation properties were tuned to enable a novel, high-throughput deposition method that is highly scalable, compatible with high loading of reinforcing fillers, and inherently low-cost.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Using Large-Scale Additive Manufacturing for Wind Turbine Blade Core Structures

This report describes the techno-economic potential of using additive manufacturing technologies to design large wind turbine blade structures. After considering all additive technologies, the authors identified large-scale, polymer-based, material extrusion as the three-dimensional (3D) printing technology best suited to meet modern wind turbine blade manufacturing costs, cycle times, and geometric scale. Due to the lower structural performance requirements and the opportunity to reduce resin uptake mass penalties within the blade, the core material within the sandwich composite sections of the wind turbine blade is established as a logical entry point into advanced wind turbine blade manufacturing.

17 WIND ENERGY↗
DOE OSTI2018

Template-free preparation and morphology evolution of (Cu, Ni) honeycomb structure via etching additive manufactured Fe-Cu-Ni alloy

Highlights: • (Cu, Ni) honeycomb structure with pore size of ~11 μm and wall thickness of ~200 nm was prepared. • The morphology evolution and the potential formation mechanism of the (Cu, Ni) honeycomb structure were investigated. • A new template-free method of additive manufacturing combined with etching was proposed to prepare ordered porous structure. • This work provides important insights into the preparation of ordered porous structure without template. - Abstract: Metallic ordered porous structures have attracted increasing attention due to their wide range of applications, but their preparation is usually accompanied with the employing of consumable templates. The development of template-free method to prepare metallic ordered porous structure can significantly reduce the cost as well as streamline the procedures. In the present work, a new template-free method of additive manufacturing combined with etching was proposed to prepare ordered porous structures. (Cu, Ni) honeycomb structure with pore size of ~11 μm and wall thickness of ~200 nm was successfully prepared from the Fe-Cu-Ni precursor alloy. The morphology evolution and the potential formation mechanism of the (Cu, Ni) honeycomb structure were studied. This work provides important insights into the preparation of ordered metallic porous structure without template.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Exceptional thermal stability of additively manufactured CoCrFeMnNi high-entropy alloy with cellular dislocation structures

CoCrFeMnNi high-entropy alloy (HEA) was additively manufactured (AM) by laser powder-bed fusion (L-PBF). The AM CoCrFeMnNi has prominent cellular dislocation structures with a small number of Mn-rich oxides. The thermal stability of the AM CoCrFeMnNi was investigated by isochronal annealing treatment at various temperatures from 400 to 1300°C for 1h. Microstructural analysis shows slow dislocation recovery, retarded recrystallization process, and precipitation of additional Cr-Mn based oxides during thermal annealing, resulting in exceptional thermal stability and retained high hardness at elevated temperatures. Further, by thermodynamic calculations, a low stored energy of 1.31 MJ/m 3 and a high activation energy of 353 kJ/mol for recrystallization were estimated for the AM CoCrFeMnNi. The exceptional thermal stability of the AM CoCrFeMnNi HEA is mechanistically attributed to the low crystallographic misorientations across the dislocation cell walls, sluggish atomic diffusion, and the pinning effects of the oxide nanoprecipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Response of solidification cellular structures in additively manufactured 316 stainless steel to heavy ion irradiation: an in situ study

In-core or cladding structural materials exposed to heavy ion irradiation often suffer serious irradiation-induced damages. Introducing defect sinks can effectively mitigate irradiation-induced degradation in materials. Here, we investigated the radiation response of additively manufactured 316 austenitic stainless steel with high-density solidification cellular structures via in situ Kr ++ irradiation at 400°C to 5dpa. The study shows that the trapped dislocations along with the cellular walls can serve as effective defect sinks, thus reduce dislocation loop density compared with the conventional coarse-grained counterparts. This study provides a positive step for the potential applications of radiation-resistant, additively manufactured steels in advanced nuclear reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2024

An additively manufactured near-eutectic Al-Ce-Ni-Mn-Zr alloy with high creep resistance

A new additively manufactured (AM) Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt.%) near-eutectic alloy is reported, which shows unprecedented creep resistance up to 400 °C (a homologous temperature of 0.72). The eutectic solidification microstructure comprises ~ 27 vol% of coarsening-resistant second phase network with an ultrafine (<100 nm) inter-phase spacing. Both Mn and Zr contribute to creep resistance of the alloy. Small amount of Mn addition promotes selection of coarsening resistant phases without compromising the alloy processability. Zr not only improves hot-tearing resistance, but further enhances the second phase coarsening resistance resulting in improved creep resistance. Neutron diffraction performed during creep deformation reveals that the underlying mechanism for creep resistance in this alloy is impedance to dislocation motion stemming from the ultrafine eutectic solidification microstructure, whereas load transfer strengthening becomes less effective as the creep temperature increases. The second phase forms a continuous network in the as-fabricated condition, which is maintained during long-term creep at 300 °C. However, this network is fragmented into fine dispersoids at higher temperatures. It is proposed that the rate-limiting deformation mechanism at 300–400 °C is (i) dislocation climb for the alloy with fragmented second phase dispersoids and (ii) Orowan looping for the alloy with a continuous second phase network. In conclusion, the present design of an AM-processable multicomponent eutectic alloy with high creep resistance can be applied to other metallic systems exhibiting eutectic reactions, with expected extreme creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Molecular dynamics simulations of radiation cascade evolution near cellular dislocation structures in additively manufactured stainless steels

The dislocation dense cellular structures observed in additively manufactured (AM) stainless steels can allow these materials to have enhanced strength and ductility compared to conventionally manufactured materials. Effective design of radiation resistant materials often necessitates creating microstructures containing of a high density of dislocations that act as sinks for radiation induced defects. This work uses molecular dynamics simulations to study the impact of pre-existing defects on radiation damage in stainless steel 316L fabricated by the laser powder bed fusion process. The evolution of synthetically generated dislocations in a crystal system in response to multiple radiation collision cascades suggest that dislocation dense regions reduce the probability of surviving point defects forming clusters. This finding seems to result from the dislocation cores’ ability to absorb point defects, thereby limiting the formation of clusters during the recombination phase. However, after successive cascades, the ability of the dislocation entanglement to prevent defect formation is diminished and defect cluster formation trends to an equilibrium. Accordingly, it is hypothesized that in an experimental setting the dislocation cells will initially act as neutral sinks for point defects, potentially delaying the onset of radiation damage effects; but, these structures will be degraded due to radiation-enhanced diffusion and lose their effectiveness at doses above 1.5–2 displacements per atom. Nevertheless, the ability to produce complex and feature-specific microstructures suggests promise for the design of radiation tolerant materials using AM methods.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Localized orientation gradients in additively manufactured stainless steel 316H structures

The high solidification rates during additive manufacturing cause highly localized thermal and strain gradients. The effect of these gradients on the evolution of local orientation misorientations within a grain is not well understood. In this study, stainless steel 316H parts were fabricated via laser powder bed fusion using three different energy densities: 43, 71, and 135 J/mm 3 . Electron backscatter diffraction showed that the maximum misorientations of the grains can be up to 25° along the build direction. Misorientation gradients (RM g ) within grains are process-dependent and can change from 0.036°/μm to 0.015°/μm with increased volumetric energy densities. In conclusion, the characterized misorientation gradients are an indication of the level of dislocations and, to an extent, the plastic deformation resulting from the rapid solidification during laser powder bed fusion.

316H↗
DOE OSTI2024

Clarifying the formation of equiaxed grains and microstructural refinement in the additive manufacturing of Ti-Cu

Controlling microstructural evolution in metallic additive manufacturing (AM) is difficult, especially in producing refined as-built grains instead of coarse, directional grains. Traditional solutions involve adding inoculants to AM feedstocks, but titanium (Ti) alloys cannot employ this approach without producing detrimental secondary phases. Ti-Cu (Ti-copper) alloys offer a solution through constitutional supercooling and/or solid state thermal cycling under AM conditions. This work analyzes a compositionally graded directed energy deposition (DED) Ti-Cu build, single-melt laser tracks, and dilatometric heat treatments to evaluate if, when, and by what mechanism(s) microstructural refinement occurs. Refinement by inoculation of unmelted powder particles was also considered. Constitutional supercooling produced no net microstructural refinement as any equiaxed dendrites which form are remelted with new deposition. This finding agreed with solidification modeling of powder bed fusion-laser beam (PBF-LB) and DED builds. Solid state thermal cycling refined microstructures only during ex-situ dilatometric heat treatments, suggesting build parameter optimization is needed to achieve refinement in-situ. Accidental heterogeneous nucleation on unmelted Ti powder, originating from the different thermophysical properties of Ti and Cu, provided the most significant microstructural refinement. This work systematically assesses the microstructural refinement mechanisms of Ti-Cu in AM builds and offers insights into microstructural control in eutectoid alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Process monitoring of additive manufacturing by using optical tomography

Parts fabricated by means of additive manufacturing are usually of complex shape and owing to the fabrication procedure by using selective laser melting (SLM), potential defects and inaccuracies are often very small in lateral size. Therefore, an adequate quality inspection of such parts is rather challenging, while non-destructive-techniques (NDT) are difficult to realize, but considerable efforts are necessary in order to ensure the quality of SLM-parts especially used for aerospace components. Thus, MTU Aero Engines is currently focusing on the development of an Online Process Control system which monitors and documents the complete welding process during the SLM fabrication procedure. A high-resolution camera system is used to obtain images, from which tomographic data for a 3dim analysis of SLM-parts are processed. From the analysis, structural irregularities and structural disorder resulting from any possible erroneous melting process become visible and may be allocated anywhere within the 3dim structure. Results of our optical tomography (OT) method as obtained on real defects are presented.

42 ENGINEERING↗
DOE OSTI2017

Volumetric Additive Manufacturing of Polymer Structures by Holographically Projected Light Fields

As additive manufacturing technologies proliferate and mature, overcoming some of their process limitations becomes increasingly important for the continued expansion of practical applications. Two such limitations that arise from layer-based fabrication are slow speed and geometric constraints (which include poor surface quality and challenges fabricating span, cantilever, and overhang elements). Moving beyond point-by-point and layer-by-layer approaches, the ability to generate a complex 3D volume as a unit operation has the potential to overcome these limitations. Since holography has been extensively studied as a means for storage and retrieval of 3D geometrical information, this dissertation explores the use of holographically-shaped light fields for producing three-dimensional structures in a “volume at once” approach. Leveraging advances in spatial light modulator (SLM) technology, phase-controlled light fields are projected into photopolymer resin to cure a desired geometry. By overlapping multiple sub-regions of a single light field within the target volume, the successful fabrication of non-periodic complex 3D geometries is demonstrated by single exposures on timescales of seconds. This dissertation presents a complete prototype platform that makes this approach possible, comprising a suitable hardware configuration along with the computational algorithms necessary to calculate and optimize the required optical fields. A study of the photopolymerization kinetics is also carried out, to determine the boundaries of usable process parameters such as resin absorbance and available light intensity. The results indicate that low-absorbing resins containing ~0.1% photoinitiator, illuminated at modest powers (~10-100 mW) may be used to produce full 3D structures from 1-10 second exposures, with volume build rates exceeding 100 cm3/hr, without layering and with no need for a substrate or support material.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural Modification and Healing of Additively Manufactured Parts by Electropulsing

For many applications, the promises of additive manufacturing (AM) of rapid development cycles and fabrication of ready-to-use, geometrically-complex parts cannot be realized because of cumbersome thermal postprocessing. This postprocessing is necessary when the nonequilibrium microstructures produced by AM lead to poor material properties. This study investigated if electropulsing, the process of sending high-current-density electrical pulses through a metallic part, could be used to modify the material properties of AM parts. This process has been used to modify conventional wrought materials but has never been applied to AM materials. Two representative AM materials were examined: 316L stainless steel and A1Si10Mg. Two hours of annealing are needed to remove chemical microsegregation in AM 316L; using electropulsing, this was accomplished in 200 seconds. The ductility of AlSil0Mg parts was increased above that of the as-built material using electropulsing. This study demonstrated that electropulsing can be used to modify the microstructures of AM metals.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Detection of Defects in Additively Manufactured Metallic Materials with Machine Learning of Pulsed Thermography Images

Additive manufacturing (AM) is an emerging method for cost-efficient fabrication of nuclear reactor parts. AM of metallic structures for nuclear energy applications is currently based on laser powder bed fusion (LPBF) process, which can introduce internal material flaws, such as pores and anisotropy. Integrity of AM structures needs to be evaluated nondestructively because material flaws could lead to premature failures due to exposure to high temperature, radiation and corrosive environment in a nuclear reactor. Quality control (QC) requires nondestructive evaluation (NDE) of actual AM structures. Pulsed thermography is a potentially promising QC technique because it is scalable to arbitrary structure size. However, detection sensitivity of this method is limited by noises. We investigate separation of signal from noise in thermography images using several machine learning (ML) methods, including new spatio-temporal blind source separation (STBSS) and spatio-temporal sparse dictionary learning (STSDL) methods. Performance of the ML methods is benchmarked using thermography data obtained from imaging stainless steel 316L and Inconel 718 specimens produced LPBF method with imprinted calibrated porosity defects. The ML methods are ranked by F-score and execution runtime. The ML methods with higher accuracy require longer run time. However, this runtime is sufficiently short to perform QC within a realistic time frame.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

In Situ, Real-Time Diagnostic to Improve the Liquid Metal Jetting Additive Manufacturing Process [Poster]

Liquid Metal Jetting (LMJ) is a metal additive manufacturing technique that involves jetting molten metal droplets at high frequencies to build solid metal parts. As an alternative to industry standard Lazer Powder Bed Fusion (LPBF) and Direct Metal Writing (DMW) techniques, LMJ poses significant advantages including no powder feed stock, no post sintering process, very high deposition rates, and the capability to print various metals. This summer, I was tasked with improving my old system to process at much higher resolution, Increasing the capture rate, and implementing this diagnostic on various LMJ setups. This system provides a vital longitudinal study to understand individual droplets in the LMJ process.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Additively Manufactured Pressure Limiting Irradiation Capsule for the High Flux Isotope Reactor

The Advanced Materials and Manufacturing Technologies (AMMT) program previously demonstrated an additively manufactured (AM) irradiation capsule (commonly referred to as a “rabbit”) from 316H stainless steel (SS) for insertion into the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL)1. This report details efforts to design and fabricate an AM pressure limiting structure (PLS) into one of the end caps of a rabbit capsule and qualify it for insertion into HFIR. The PLS includes a thin cylindrical rupture wall, a shield, and internal supports to facilitate printing and ensure mechanical integrity. Its overall dimensions are 9-mm tall and 10-mm in diameter— equivalent to about one-fourth of the size of a AAA battery. The PLS maintains safe internal operating pressures for a rabbit capsule while in the reactor. Although this application is specific to HFIR, the approach lends itself to further applications in industrial, aeronautical, advanced space and power generation environments. Several PLS rabbits capsules have been successfully designed, fabricated, pressure tested, and qualified for future insertion into the HFIR for irradiation and post-irradiation evaluation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗