Search NASA⌕ Search

SEARCH · Search NASA

Results for “Advanced Materials Processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

AFIP-6 Fabrication Summary Report

The AFIP-6 (ATR Full-size plate In center flux trap Position) experiment was designed to evaluate the performance of monolithic fuels at a scale prototypic of research reactor fuel plates. Two qualified fueled plates were fabricated for the AFIP-6 experiment; to be irradiated in the INL Advanced Test Reactor (ATR). This report provides details of the fuel fabrication efforts, including material selection, fabrication processes, and fuel plate qualification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of Harrell Monosodium Titanate Lot #s 46000606120, 46000722120, AND 46000808120

Monosodium titanate (MST) for use in the Actinide Removal Process (ARP) must be qualified and verified in advance. A single qualification sample for each batch of material is sent to SRNL for analysis, as well as a statistical sampling of verification samples. The Harrell Industries Lot #s 46000706120, 46000722120, and 460008081120 qualification and verification samples met each of the selected specification requirements that were tested with the exception of a few pails being marginally below the lower weight percent solids limit. These deviations from the specifications are viewed as negligible since the corresponding density of the slurries indicates no appreciable shortage of MST solids. Therefore, SRNL recommends acceptance and use of these pails.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Analysis of Harrell Monosodium Titanate Lot #46000908120

Monosodium titanate (MST) for use in the Actinide Removal Process (ARP) must be qualified and verified in advance. A single qualification sample for each batch of material is sent to SRNL for analysis, as well as a statistical sampling of verification samples. The Harrell Industries Lot #46000908120 qualification and the 16 verification samples failed to meet the specification for weight percent solids. All of the pails sampled and tested contained less than 15 wt % MST solids.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Analysis of Harrell Monosodium Titanate Lot #46000824120

Monosodium titanate (MST) for use in the Actinide Removal Process (ARP) must be qualified and verified in advance. A single qualification sample for each batch of material is sent to SRNL for analysis, as well as a statistical sampling of verification samples. The Harrell Industries Lot #46000824120 qualification and the 16 verification samples failed to meet the specification for weight percent solids. All of the pails sampled and tested contained less than 15 wt % MST solids.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Manufacturing Demonstration Facility: Low Temperature Materials Synthesis

The Manufacturing Demonstration Facility (MDF) low temperature materials synthesis project was established to demonstrate a scalable and sustainable process to produce nanoparticles (NPs) for advanced manufacturing. Previous methods to chemically synthesize NPs typically required expensive, high-purity inorganic chemical reagents, organic solvents and high temperatures. These processes were typically applied at small laboratory scales at yields sufficient for NP characterization, but insufficient to support roll-to-roll processing efforts or device fabrication. The new NanoFermentation processes described here operated at a low temperature (~60 C) in low-cost, aqueous media using bacteria that produce extracellular NPs with controlled size and elemental stoichiometry. Up-scaling activities successfully demonstrated high NP yields and quality in a 900-L pilot-scale reactor, establishing this NanoFermentation process as a competitive biomanufacturing strategy to produce NPs for advanced manufacturing of power electronics, solid-state lighting and sensors.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Engineering Analysis Baseline Model Requirements

The purpose of this document is to set requirements for the development, documentation, implementation, and maintenance of engineering analysis baseline models used by the Advanced Engineering and Analysis group to model and simulate systems. The intended audience of this document is the Engineering Technology and Design division Advanced Engineering and Analysis group—in particular the baseline model owners and users—and the Group Leaders and members of the Systems Engineering groups. Section 1 presents a discussion of general concepts related to engineering analysis models and baseline models, including definitions of common terms used in this requirements document. It also presents the purpose and intentions of creating and using baseline models and exposes some underlying assumptions about what baseline models are supposed to be. Section 2 presents requirements on the general categories of: the Advanced Engineering and Analysis Group Leader and the baseline model owner; parts, materials, and load cases; the process of generating and using the model; and how the baseline model will be stored, maintained, and documented. This document presents requirements on the baseline model as well as some aspects of the development process and the people responsible for the development; it does not address how the results of simulations utilizing these models will be used to make assessments

42 ENGINEERING↗

Basic Research Needs for Synthesis Science (Brochure)

The technology at our fingertips becomes more powerful each day. Smartphones are handheld computers, cameras, music players, boarding passes, and sometimes phones. Cars are ever more fuel-efficient, safer and loaded with computing power. LED lighting and solar panels are becoming common worldwide. None of these advances would have been possible without the capability to discover, develop, and create new materials and chemical processes. If the only limit to synthesizing new forms of matter were the imagination of scientists, then assemblies of atoms and molecules with unparalleled new architectures and capabilities would be possible—catalysts that turn garbage into fuels, solar cells to power buildings directly from sunlight, batteries with the energy density of gasoline, and materials that transport charge hundreds of times faster than silicon.

36 MATERIALS SCIENCE↗

AFIP-4 Fabrication Summary Report

The AFIP-4 (ATR Full –size-plate In center flux trap Position) experiment was designed to evaluate the performance of monolithic fuels at a scale prototypic of research reactor fuel plates. Twelve qualified fueled plates were fabricated for the AFIP-4 experiment; to be irradiated in the INL Advanced Test Reactor (ATR). This report provides details of the fuel fabrication efforts; including material selection, fabrication processes, and fuel plate qualification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Desorption lifetimes and activation energies influencing gas–surface interactions and multiphase chemical kinetics

Abstract. Adsorption and desorption of gases on liquid or solid substrates are involved in multiphase processes and heterogeneous chemical reactions. The desorption energy (Edes0), which depends on the intermolecular forces between adsorbate and substrate, determines the residence time of chemical species at interfaces. We show how Edes0 and temperature influence the net uptake or release of gas species, the rates of surface–bulk exchange and surface or bulk reactions, and the equilibration timescales of gas–particle partitioning. Using literature data, we derive a parameterization to estimate Edes0 for a wide range of chemical species based on the molecular mass, polarizability, and oxygen-to-carbon ratio of the desorbing species independent of substrate-specific properties, which is possible because of the dominant role of the desorbing species' properties. Correlations between Edes0 and the enthalpies of vaporization and solvation are rooted in molecular interactions. The relation between Edes0 and desorption kinetics reflects the key role of interfacial exchange in multiphase processes. For small molecules and semi-volatile organics (VOC, IVOC, SVOC), Edes0 values around 10–100 kJ mol−1 correspond to desorption lifetimes around nanoseconds to days at room temperature. Even higher values up to years are obtained at low temperatures and for low volatile organic compounds (LVOC, ELVOC/ULVOC) relevant for secondary organic aerosols (SOA). Implications are discussed for SOA formation, gas–particle partitioning, organic phase changes, and indoor surface chemistry. We expect these insights to advance the mechanistic and kinetic understanding of multiphase processes in atmospheric and environmental physical chemistry, aerosol science, materials science, and chemical engineering.

54 ENVIRONMENTAL SCIENCES↗

The role of the Long Duration Exposure Facility in the development of space systems

The Long Duration Exposure Facility (LDEF) presents the international, aerospace community with an unprecedented opportunity to examine the synergistic, long term, space environmental effects on systems and materials. The analysis of the data within appropriate environmental contexts is essential to the overall process of advancing the understanding of space environmental effects needed for the continuing development of strategies to improve the reliability and durability of space systems and to effectively deal with the future challenges that new space initiatives will likely present.

Sally A. Little↗

An Approach to Establishing System Benefits for Technology in NASA's Hypersonics Investment Area

NASA's has established long term goals for access-to-space. The third generation launch systems are to be fully reusable and operational around 2025. The goals for the third generation launch system are to significantly reduce cost and improve safety over current systems. The Advanced Space Transportation Program (ASTP) Office at the NASA's Marshall Space Flight Center in Huntsville, AL has the agency lead to develop space transportation technologies. Within ASTP, under the Hypersonics Investment Area, third generation technologies are being pursued. The Hypersonics Investment Area's primary objective is to mature vehicle technologies to enable substantial increases in the design and operating margins of third generation RLVs (current Space Shuttle is considered the first generation RLV) by incorporating advanced propulsion systems, materials, structures, thermal protection systems, power, and avionics technologies. The paper describes the system process, tools and concepts used to determine the technology benefits. Preliminary results will be presented along with the current technology investments that are being made by ASTP's Hypersonics Investment Area.

Hueter, Uwe↗

(abstract) Application of Neural Networks to Hyperspectral Unmixing

The emergence, in recent years, of hyperspectral sensors provides a tremendous opportunity for advancing the process of detailed and direct remote detection and identification from space of targets or surface materials. Such sensors exploit the uniqueness of the corresponding spectral reflectance signatures, which enables high resolution imaging spectrometer data to be processed on a pixel-by-pixel basis. This has implications both for defense-related applications (e.g., surveillance tasks) and in the civilian domain (e.g., for science applications). The purpose of this talk is to discuss a number of strong arguments that support neural networks as a choice for the generalized analysis (e.g., unmixing) of remotely sensed hyperspectral data.

signatures moving object detection surveillance co↗

Automated Ply-By-Ply Lamination and in-Situ Consolidation of Dry Carbon Fiber Non-Crimp Fabrics for High-Rate Aircraft Manufacturing of Structural Aircraft Components

NASA’s Hi-Rate Composites Aircraft Manufacturing (HiCAM) program addresses market needs to advance structural aircraft composite manufacturing technologies to significantly increase production rates. Dry, non-crimp fabric (NCF) carbon materials infused with advanced resin systems offer a promising solution to these manufacturing demands. Northrop Grumman’s Automated Stiffener Forming (ASF) technology has been adapted for ply-by-ply, in-situ processing of NCF materials. The modular ASF process accommodates flexibility in the laminate stacking, while allowing for ply drops, ply additions, and yaw, pitch, and roll in the laminate geometry. To adapt the ASF process for NCF materials, heating technologies and roller compaction processes were designed and tested on representative structural aircraft part geometries. Key success criteria for the ASF process with NCF materials is forming quality and preform compaction. Trials were performed with multiple NCF materials: unidirectional up to quad-axial formats. The NCF constituents, veils, stitching, and binders, were evaluated with the ASF process. The material performance in the ASF process and the resulting preform quality are presented.

dry carbon fiber materials↗

Automated Ply-By-Ply Lamination and in-Situ Consolidation of Dry Carbon Fiber Non-Crimp Fabrics for High-Rate Aircraft Manufacturing of Structural Aircraft Components

NASA’s Hi-Rate Composites Aircraft Manufacturing (HiCAM) program addresses market needs to advance structural aircraft composite manufacturing technologies to significantly increase production rates. Dry, non-crimp fabric (NCF) carbon materials infused with advanced resin systems offer a promising solution to these manufacturing demands. Northrop Grumman’s Automated Stiffener Forming (ASF) technology has been adapted for ply-by-ply, in-situ processing of NCF materials. The modular ASF process accommodates flexibility in the laminate stacking, while allowing for ply drops, ply additions, and yaw, pitch, and roll in the laminate geometry. To adapt the ASF process for NCF materials, heating technologies and roller compaction processes were designed and tested on representative structural aircraft part geometries. Key success criteria for the ASF process with NCF materials is forming quality and preform compaction. Trials were performed with multiple NCF materials: unidirectional up to quad-axial formats. The NCF constituents, veils, stitching, and binders, were evaluated with the ASF process. The material performance in the ASF process and the resulting preform quality are presented.

dry carbon fiber materials↗

Advanced Reactors Thermal Energy Transport for Process Industries

The operation temperature of advanced nuclear reactors is generally higher than commercial light water reactors and thermal energy from advanced nuclear reactor can be used for various purposes such as liquid fuel production, district heating, desalination, hydrogen production, and other process heat applications, etc. Some of the major technology challenges that must be overcome before the advanced reactors could be licensed on the reactor side are qualification of next generation of nuclear fuel, materials that can withstand higher temperature, improvement in power cycle thermal efficiency by going to combined cycles, SCO2 cycles, successful demonstration of advanced compact heat exchangers in the prototypical conditions, and from the process side application the challenge is to transport the thermal energy from the reactor to the process plant with maximum efficiency (i.e., with minimum temperature drop). The main focus of this study is on doing a parametric study of efficient heat transport system, with different coolants (mainly, water, He, and molten salts) to determine maximum possible distance that can be achieved.

42 ENGINEERING↗

Mobile Hot Cell Digital Twin: End-of-life Management of Disused High Activity Radioactive Sources – 23598

Sealed radioactive sources are utilized for a wide range of applications across nuclear facilities, universities, hospitals, and industry. When these sources reach the end of serviceable life, they become waste. As waste, this radioactive material then goes through a process of recapture and then transfer to long term storage. With the advancement of technology in conjunction with better accessibility of technology, industries are exploring the use of digital automation to enhance productivity, efficiency, and safety while minimizing operation and maintenance costs, health and environmental risks, and uncertainty in the project life cycles. One area for exploration is the use of a digital twin to help design a robust, versatile, and safe solution for recapturing spent sources. We believe this avenue can also provide further advantages in the operations aspect of end-of-life management of spent radioactive sources by reducing the deployment time, increasing operator safety, and reducing operation & maintenance cost. We present a novel digital twin framework for end-of-life management of disused high activity radioactive sources. We have designed and developed a framework that houses a digital twin for visualizing and monitoring the recapture process to inform the engineering and design of a new Mobile Hot Cell. Furthermore, we demonstrate the feasibility of the proposed framework by providing a prototypical implementation, supporting the Mobile Hot Cell and human-machine interface's virtual replication.

61 RADIATION PROTECTION AND DOSIMETRY↗

Surface Preparation of Additively Manufactured 316H Stainless Steel for Molten Salt Applications

Additive manufacturing (AM) has the potential to revolutionize the manufacturing process and speed up deployment of advance nuclear reactors. However, more information is needed on preparing AM materials for extreme reactor environments to qualify AM materials for nuclear applications. This project studies the surface preparation of AM 316H stainless steel using acid pickling and reports a successful procedure for descaling heat-treated AM material.

316H Stainless Steel↗

Development of Advanced Alloys using Fullerenes

Development of advanced alloys using fullerenes is currently underway to produce materials for use in the extravehicular mobility unit (EMU). These materials will be directed toward commercial usages as they are continually developed. Fullerenes (of which the most common is C(sub 60)) are lightweight, nanometer size, hollow molecules of carbon which can be dispersed in conventional alloy systems to enhance strength and reduce weight. In this research, fullerene interaction with aluminum is investigated and a fullerene-reinforced aluminum alloy is being developed for possible use on the EMU. The samples were manufactured using standard commercial approaches including powder metallurgy and casting. Alloys have been processed having 1.3, 4.0 and 8.0 volume fractions of fullerenes. It has been observed that fullerene dispersion is related to the processing approach and that they are stable for the processing conditions used in this research. Emphasis will be given to differential thermal analysis and wavelength dispersive analysis of the processed alloys. These two techniques are particularly useful in determining the condition of the fullerenes during and after processing. Some discussion will be given as to electrical properties of fullerene-reinforced materials. Although the aluminum and other advanced alloys with fullerenes are being developed for NASA and the EMU, the properties of these materials will be of interest for commercial applications where specific Dual-Use will be given.

Sims, J.↗