Excess-Entropy Scaling for Gas Diffusivity in Nanoporous Materials
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The impact of Al protection on the electrochemical performance of high-voltage lithium-ion chemistries was studied using LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC 622) as a model material. A thin-layer of AlPO 4 coating was prepared on Al current collectors to act as an artificial barrier against Al corrosion at high potentials. This coating was characterized by SEM, FTIR, and XPS. The coated Al showed higher electrochemical stability and was more resistive to corrosion compared to the bare foil. This beneficial effect was further confirmed by depth-dependent XPS studies. NMC 622/Li half-cells with coated and bare Al current collectors were constructed and a direct correlation between the cyclability of NMC 622 and the corrosion of Al was confirmed. The AlPO 4 coating suppressed Al corrosion and improved cell performance. A more substantial enhancement was achieved under a high temperature-high current cycling condition. The cell with AlPO 4 coating on Al exhibited smaller impedance, better capacity retention, and higher coulombic efficiency over cycling. In conclusion, these properties of the AlPO 4 coating are highly desirable and can provide the same beneficial effects for all other high-voltage cathodes with different chemistries.
We devise a model to explain why twisted bilayer graphene exhibits insulating behavior when ν = 2 or 3 charges occupy a unit moiré cell, a feature attributed to Mottness per previous work but not for ν = 1, clearly inconsistent with Mott insulation. We compute $r_s$ = EU/EK, where EU and EK are the potential and kinetic energies, respectively, and show that (i) the Mott criterion lies at a density larger than experimental values by a factor of 104 and (ii) a transition to a series of Wigner crystalline states exists as a function of ν. We find that, for ν = 1, $r_s$ fails to cross the threshold ($r_s$ = 37) for the triangular lattice, and metallic transport ensues. However, for ν = 2 and ν = 3, the thresholds $r_s$ = 22 and $r_s$ = 17, respectively, are satisfied for a transition to Wigner crystals (WCs) with a honeycomb (ν = 2) and a kagome (ν = 3) structure. We posit that such crystalline states form the correct starting point for analyzing superconductivity.
The recently developed contact-corrected density functional theory is applied to an electric double layer containing a valence and size symmetric electrolyte. The restricted primitive model is used to describe the electrolyte, and a non-polarisable, smooth, planar, uniformly charged hard surface is used to model the electrode. Comparison with Monte Carlo simulation results for this system shows that the theory satisfies the first contact value relation in line with the premise of the approach. Additionally, the theory is found to satisfy the semi-empirical second contact value relation quite closely. This is a welcome result, since no reference is made to this second relation nor is the relation used in the theoretical development. The second contact relation is closely related to the anomalous positive temperature derivative of the double layer capacitance at low temperature, low ion concentration, and low electrode charge, and indeed, the contact-corrected density functional theory predicts this effect.
Vertical stacking is widely viewed as a promising approach for designing advanced functionalities using two-dimensional (2D) materials. Combining crystallographically commensurate materials in these 2D stacks has been shown to result in rich new electronic structure, magnetotransport, and optical properties. In this context, vertical stacks of crystallographically incommensurate 2D materials with well-defined crystallographic order are a counterintuitive concept and, hence, fundamentally intriguing. We show that crystallographically dissimilar and incommensurate atomically thin MoS 2 and Bi 2 Se 3 layers can form rotationally aligned stacks with long-range crystallographic order. Our first-principles theoretical modeling predicts heterocrystal electronic band structures, which are quite distinct from those of the parent crystals, characterized with an indirect bandgap. Experiments reveal striking optical changes when Bi 2 Se 3 is stacked layer by layer on monolayer MoS 2 , including 100% photoluminescence (PL) suppression, tunable transmittance edge (1.1→0.75 eV), suppressed Raman, and wide-band evolution of spectral transmittance. Disrupting the interface using a focused laser results in a marked the reversal of PL, Raman, and transmittance, demonstrating for the first time that in situ manipulation of interfaces can enable “reconfigurable” 2D materials. We demonstrate submicrometer resolution, “laser-drawing” and “bit-writing,” and novel laser-induced broadband light emission in these heterocrystal sheets.
A low cost, flexible and modular spacecraft power system design was developed in response to a call for an architecture that could accommodate multiple missions in the small to medium load range. Three upcoming satellites will use this design, with one launch date in 1999 and two in the year 2000. The design consists of modular hardware that can be scaled up or down, without additional cost, to suit missions in the 200 to 600 Watt orbital average load range. The design will be applied to satellite orbits that are circular, polar elliptical and a libration point orbit. Mission unique adaptations are accomplished in software and firmware. In designing this advanced, adaptable power system, the major goals were reduction in weight volume and cost. This power system design represents reductions in weight of 78 percent, volume of 86 percent and cost of 65 percent from previous comparable systems. The efforts to miniaturize the electronics without sacrificing performance has created streamlined power electronics with control functions residing in the system microprocessor. The power system design can handle any battery size up to 50 Amp-hour and any battery technology. The three current implementations will use both nickel cadmium and nickel hydrogen batteries ranging in size from 21 to 50 Amp-hours. Multiple batteries can be used by adding another battery module. Any solar cell technology can be used and various array layouts can be incorporated with no change in Power System Electronics (PSE) hardware. Other features of the design are the standardized interfaces between cards and subsystems and immunity to radiation effects up to 30 krad Total Ionizing Dose (TID) and 35 Mev/cm(exp 2)-kg for Single Event Effects (SEE). The control algorithm for the power system resides in a radiation-hardened microprocessor. A table driven software design allows for flexibility in mission specific requirements. By storing critical power system constants in memory, modifying the system code for other programs is simple. These constants can be altered also by ground command, or in response to an anomolous event. All critical power system functions have backup hardware functions to prevent a software or computer glitch from propagating. A number of battery charge control schemes can be implemented by selecting the proper control terms in the code. The architecture allows the design engineer to tune the system response to various system components and anticipated load profiles without costly alterations. A design trade was made with the size, weight and power dissipation of the electronics versus the performance of the power bus to load variations. Linear, fine control is maintained with a streamlined electronics design. This paper describes the hardware design as well as the software control algorithm. The challenges of closing the system control loop digitally is discussed. Control loop margin and power system performance is presented. Lab measurements are shown and compared to the system response of a hardware model running actual flight software.
Small amounts of an impurity may affect the key properties of an ionic liquid and such effects can be dramatically amplified when the electrolyte is under confinement. Here the classical density functional theory is employed to investigate the impurity effects on the microscopic structure and the performance of ionic-liquid-based electrical double-layer capacitors, also known as supercapacitors. Using a primitive model for ionic species, we study the effects of an impurity on the double layer structure and the integral capacitance of a room temperature ionic liquid in model electrode pores and find that an impurity strongly binding to the surface of a porous electrode can significantly alter the electric double layer structure and dampen the oscillatory dependence of the capacitance with the pore size of the electrode. Meanwhile, a strong affinity of the impurity with the ionic species affects the dependence of the integral capacitance on the pore size. Up to 30% increase in the integral capacitance can be achieved even at a very low impurity bulk concentration. By comparing with an ionic liquid mixture containing modified ionic species, we find that the cooperative effect of the bounded impurities is mainly responsible for the significant enhancement of the supercapacitor performance.
This presentation uses a vehicle simulator and economics model called the Battery Ownership Model to examine the levelized cost per mile of conventional (CV) and hybrid electric vehicles (HEVs) in comparison with the cost to operate an electric vehicle (EV) under a service provider business model. The service provider is assumed to provide EV infrastructure such as charge points and swap stationsto allow an EV with a 100-mile range to operate with driving profiles equivalent to CVs and HEVs. Battery cost, fuel price forecast, battery life, and other variables are examined to determine under what scenarios the levelized cost of an EV with a service provider can approach that of a CV. Scenarios in both the United States as an average and Hawaii are examined. The levelized cost ofoperating an EV with a service provider under average U.S. conditions is approximately twice the cost of operating a small CV. If battery cost and life can be improved, in this study the cost of an EV drops to under 1.5 times the cost of a CV for U.S. average conditions. In Hawaii, the same EV is only slightly more expensive to operate than a CV.
A proposed thermoelectric device would exploit natural temperature differences between air and soil to harvest small amounts of electric energy. Because the air/soil temperature difference fluctuates between nighttime and daytime, it is almost never zero, and so there is almost always some energy available for harvesting. Unlike photovoltaic cells, the proposed device could operate in the absence of sunlight. Unlike a Stirling engine, which could be designed to extract energy from the air/soil temperature difference, the proposed device would contain no moving parts. The main attractive feature of the proposed device would be high reliability. In a typical application, this device would be used for low-power charging of a battery that would, in turn, supply high power at brief, infrequent intervals for operating an instrumentation package containing sensors and communication circuits. The device (see figure) would include a heat exchanger buried in soil and connected to a heat pipe extending up to a short distance above the ground surface. A thermoelectric microgenerator (TEMG) would be mounted on top of the heat pipe. The TEMG could be of an advanced type, now under development, that could maintain high (relative to prior thermoelectric generators) power densities at small temperature differentials. A heat exchanger exposed to the air would be mounted on top of the TEMG. It would not matter whether the air was warmer than the soil or the soil warmer than the air: as long as there was a nonzero temperature difference, heat would flow through the device and electricity would be generated. A study of factors that could affect the design and operation of the device has been performed. These factors include the thermal conductances of the soil, the components of the device, the contacts between the components of the device, and the interfaces between the heat exchangers and their environments. The study included experiments that were performed on a model of the device to demonstrate feasibility. Because a TEMG suitable for this device was not available, a brass dummy component having a known thermal conductance of 1.68 W/K was substituted for the TEMG in the models to enable measurement of heat flows. The model included a water-based heat pipe 30 in. (76.2 cm) long and 1 in. (2.54 cm) in diameter, wrapped with polyethylene insulation to reduce radial heat flow. Several different side heat exchangers were tested. On the basis of the measurements, it was predicted that if a prototype of the device were equipped with a TEMG, daily temperature fluctuations would cause its output power to fluctuate between 0 and about 0.1 mW, peaking to 0.35 mW during early afternoon.
The energy density of an electric double layer (EDL) capacitor, a type of supercapacitor, depends on the ion distribution within the micropores of electrodes that are typically made of amorphous carbon. By using coarse-grained models and the classical density functional theory, we investigate the distributions of ionic species among different idealized nanopores in contact with an asymmetric ionic liquid mixture and the effects of the bulk electrolyte composition on capacitive energy storage. We find that a charged pore is always small-ion selective, provided all ions have the same valence and similar non-electrostatic interactions. While small ions enhance both the EDL capacitance and the accessibility of micropores, an ionic mixture containing ions of different sizes may yield a capacitance higher than those corresponding to pure ionic liquids. Furthermore, the increased capacitance may be attributed to more efficient ion packing near the charged surface. At certain conditions, the improvement is on a par with the anomalous capacitance rise for pure ionic liquids in electrodes with ultranarrow pores.
A multi-scale mathematical model, which accounts for mass transport on the crystal and agglomerate length-scales, is used to investigate the electrochemical performance of lithium-magnetite electrochemical cells. Experimental discharge and voltage recovery data are compared to three sets of simulations, which incorporate crystal-only, agglomerate-only, or multi-scale transport effects. Mass transport diffusion coefficients are determined by fitting the simulated voltage recovery times to experimental data. In addition, a further extension of the multi-scale model is proposed which accounts for the impact of agglomerate size distributions on electrochemical performance. The results of the study indicate that, depending on the crystal size, the low utilization of the active material is caused by transport limitations on the agglomerate and/or crystal length-scales. For electrodes composed of small crystals (6 and 8 nm diameters), it is concluded that the transport limitations in the agglomerate are primarily responsible for the long voltage recovery times and low utilization of the active mass. In the electrodes composed of large crystals (32 nm diameter), the slow voltage recovery is attributed to transport limitations on both the agglomerate and crystal length-scales.
Battery wear in plug-in electric vehicles (PEVs) is a complex function of ambient temperature, battery size, and disparate usage. Simulations capturing varying ambient temperature profiles, battery sizes, and driving patterns are of great value to battery and vehicle manufacturers. A predictive battery wear model developed by the National Renewable Energy Laboratory captures the effects ofmultiple cycling and storage conditions in a representative lithium chemistry. The sensitivity of battery wear rates to ambient conditions, maximum allowable depth-of-discharge, and vehicle miles travelled is explored for two midsize vehicles: a battery electric vehicle (BEV) with a nominal range of 75 mi (121 km) and a plug-in hybrid electric vehicle (PHEV) with a nominal charge-depleting rangeof 40 mi (64 km). Driving distance distributions represent the variability of vehicle use, both vehicle-to-vehicle and day-to-day. Battery wear over an 8-year period was dominated by ambient conditions for the BEV with capacity fade ranging from 19% to 32% while the PHEV was most sensitive to maximum allowable depth-of-discharge with capacity fade ranging from 16% to 24%. The BEV and PHEV werecomparable in terms of petroleum displacement potential after 8 years of service, due to the BEV?s limited utility for accomplishing long trips.
One of the most fundamental design considerations for any space vehicle is its power supply system. Many options exist, including batteries, fuel cells, nuclear reactors, radioisotopic thermal generators (RTGs), and solar panel arrays. Solar arrays have many advantages over other types of power generation. They are lightweight and relatively inexpensive, allowing more mass and funding to be allocated for other important devices, such as scientific instruments. For Mars applications, solar power is an excellent option, especially for long missions. One might think that dust storms would be a problem; however, while dust blocks some solar energy, it also scatters it, making it diffuse rather than beamed. Solar cells are still able to capture this diffuse energy and convert it into substantial electrical power. For these reasons, solar power was chosen to be used on the 1997 Mars Pathfinder mission. The success of this mission set a precedent, as NASA engineers have selected solar power as the energy system of choice for all future Mars missions, including the Mars Exploration Rover (MER) Project. Solar sells have their drawbacks, however. They are difficult to manufacture and are relatively fragile. In addition, solar cells are highly sensitive to different parts of the solar spectrum, and finding the correct balance is crucial to the success of space missions. Another drawback is that the power generated is not a constant with respect to time, but rather changes with the relative angle to the sun. On Mars, dust accumulation also becomes a factor. Over time, dust settles out of the atmosphere and onto solar panels. This dust blocks and shifts the frequency of the incoming light, degrading solar cell performance. My goal is to analyze solar panel telemetry data from the two MERs (Spirit and Opportunity) in an effort to accurately model the effect of dust accumulation on solar panels. This is no easy process due to the large number of factors involved. Changing solar flux (the amount of solar energy reaching the planet), solar spectrum, solar angle, rover tilt, and optical depth (the opacity of the atmosphere due to dust) were the most significant. Microsoft Excel and Visual Basic are used for data analysis. The results of this work will be used to improve the dust accumulation and atmosphere effects model that was first created after the Mars Pathfinder mission. This model will be utilized and applied when considering the design of solar panel array systems on future Mars projects. Based on this data, and depending upon the tenure and application of the mission, designers may also elect to employ special tools to abate dust accumulation, or decide that the expected level of accumulation is acceptable.
Explore the source record for details and available documents.
In this work, we show that the pressure-induced metal-insulator transition (MIT) in LaMnO 3 is fundamentally different from the Mott-Hubbard transition and is percolative in nature, with the measured resistivity obeying the percolation scaling laws. Using the Gutzwiller method to treat correlation effects in a model Hamiltonian that includes both Coulomb and Jahn-Teller interactions, we show, one, that the MIT is driven by a competition between electronic correlation and the electron-lattice interaction, an issue that has been long debated, and two, that with compressed volume, the system has a tendency towards phase separation into insulating and metallic regions, consisting, respectively, of Jahn-Teller distorted and undistorted octahedra. This tendency manifests itself in a mixed phase of intermixed insulating and metallic regions in the experiment. Conduction in the mixed phase occurs by percolation and the MIT occurs when the metallic volume fraction, steadily increasing with pressure, exceeds the percolation threshold v c ≈ 0.29. Finally, measured high-pressure resistivity follows the percolation scaling laws quite well, and the temperature dependence follows the Efros-Shklovskii variable-range hopping behavior for granular materials.
Based on the random phase approximation (RPA), RPA renormalization is a robust many-body perturbation theory that works for molecules and materials because it does not diverge as the Kohn-Sham gap approaches zero. Additionally, RPA renormalization enables the simultaneous calculation of RPA and beyond-RPA correlation energies since the total correlation energy is the sum of a series of independent contributions. The first-order approximation (RPAr1) yields the dominant beyond-RPA contribution to the correlation energy for a given exchange-correlation kernel, but systematically underestimates the total beyond-RPA correction. For both the homogeneous electron gas model and real systems, we demonstrate numerically that RPA renormalization beyond first order converges monotonically to the infinite-order beyond-RPA correlation energy for several model exchange-correlation kernels and that the rate of convergence is principally determined by the choice of the kernel and spin polarization of the ground state. The monotonic convergence is rationalized from an analysis of the RPA renormalized correlation energy corrections, assuming the exchange-correlation kernel and response functions satisfy some reasonable conditions. In this work, for spin-unpolarized atoms, molecules, and bulk solids, we find that RPA renormalization is typically converged to 1 meV error or less by fourth order regardless of the band gap or dimensionality. Most spin-polarized systems converge at a slightly slower rate, with errors on the order of 10 meV at fourth order and typically requiring up to sixth order to reach 1 meV error or less. Slowest to converge, however, open-shell atoms present the most challenging case and require many higher orders to converge.
Covalent tethering of PPh2NC6H4C=CH2 ligands (PPh2NC6H4C=CH2 = 1,5-di-(4-ethynylphenyl)-3,7-diphenyl-1,5-diaza-3,7-diphosphacyclooctane) to planar, azide-terminated glassy carbon electrode surfaces has been accomplished using a CuI-catalyzed alkyne-azide cycloaddition (CuAAC) as the coupling reaction, using a BH3?P protection-deprotection strategy. Deprotected, surface-confined ligands were metallated using [NiII(MeCN)6](BF4)2. X-ray photoelectron spectroscopic measurements demonstrate that metallation introduced 1.3 equivalents NiII per diphosphine onto the electrode surface. Exposure of the surface to a second diphosphine ligand, PPh2NPh2, resulted in the removal of Ni from the surface. Protection, coupling, deprotection, and metallation conditions were optimized using solution-phase model systems, with benzyl azide as a model for the azide-terminated carbon surface; these reactions generate a [NiII(diphosphine)2]2+ complex. Acknowledgment. This research was supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences. The XPS measurements were performed at the Environmental Molecular Sciences Laboratory (EMSL), a national scientific user facility sponsored by the U. S. Department of Energy, Office of Science, Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory. The x-ray crystal structure analysis was carried out by S.L., who was supported by a grant to Wendy J. Shaw from the Early Career Research Program through the U.S. Department of Energy, Office of Science. Pacific Northwest National Laboratory is operated by Battelle for the U.S. Department of Energy.