Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computational optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Optimization of contoured hypersonic scramjet inlets with a least-squares parabolized Navier-Stokes procedure

A new optimization procedure, in which a parabolized Navier-Stokes solver is coupled with a non-linear least-squares optimization algorithm, is applied to the design of a Mach 14, laminar two-dimensional hypersonic subscale flight inlet with an internal contraction ratio of 15:1 and a length-to-throat half-height ratio of 150:1. An automated numerical search of multiple geometric wall contours, which are defined by polynomical splines, results in an optimal geometry that yields the maximum total-pressure recovery for the compression process. Optimal inlet geometry is obtained for both inviscid and viscous flows, with the assumption that the gas is either calorically or thermally perfect. The analysis with a calorically perfect gas results in an optimized inviscid inlet design that is defined by two cubic splines and yields a mass-weighted total-pressure recovery of 0.787, which is a 23% improvement compared with the optimized shock-canceled two-ramp inlet design. Similarly, the design procedure obtains the optimized contour for a viscous calorically perfect gas to yield a mass-weighted total-pressure recovery value of 0.749. Additionally, an optimized contour for a viscous thermally perfect gas is obtained to yield a mass-weighted total-pressure recovery value of 0.768. The design methodology incorporates both complex fluid dynamic physics and optimal search techniques without an excessive compromise of computational speed; hence, this methodology is a practical technique that is applicable to optimal inlet design procedures.

Korte, J. J.↗

Propulsion-Airframe Integration for Conceptual Redesign of a Low-Boom Supersonic Transport

A low-boom supersonic transport was generated in a previous low-boom multidisciplinary optimization (MDO) study that used computational fluid dynamics (CFD) off-body pressure to compute the undertrack sonic boom ground signature and calibrated low-fidelity aerodynamics analyses to compute the mission performance metrics. This low-boom aircraft, referred to as the Mach 1.7 40-PAX concept, can carry 40 passengers for a low-boom overland mission with cruise Mach 1.7 for the airport pairs over the continental US and has the potential to achieve an undertrack sonic boom ground noise level below 70 perceived level of decibels at the start of overland cruise (SOC). The engine for the Mach 1.7 40-PAX concept was designed using the Numerical Propulsion System Simulation (NPSS) for the mission analysis and modeled as a flow-through nacelle for CFD-based sonic boom analysis. To understand how the engine plume affects the undertrack ground signature, the Mach 1.7 40-PAX concept is redesigned in this paper after replacing the flow-through nacelles by CFD engines for sonic boom analysis using aeropropulsive CFD simulation. A process is developed for approximation of the NPSS engine at SOC by a CFD engine for aeropropulsive CFD simulation. The generated CFD engine has the identical nozzle boundary conditions and approximately the same mass flow and thrust as those of the NPSS engine at SOC. Then, the outer mold line of the configuration with the CFD engines is redesigned to approximately restore the low-boom characteristics of the Mach 1.7 40-PAX concept at SOC. Finally, the CFD simulation data for the redesigned concept with the CFD engines is used to calibrate the low-fidelity aerodynamic analyses for mission analysis of this concept. The cyclic dependency of the involved disciplinary analyses is resolved using an iteration method for a consistent coupling of the mission analysis, NPSS engine analysis, and low-boom redesign using the aeropropulsive CFD simulation. This low-boom redesign study is used as an example to demonstrate how the propulsion-airframe integration could be implemented for conceptual design of supersonic transports that satisfy both the low-boom and mission performance requirements.

Low-boom supersonic transport↗

A random search algorithm for laboratory computers

The small laboratory computer is ideal for experimental control and data acquisition. Postexperimental data processing is often performed on large computers because of the availability of sophisticated programs, but costs and data compatibility are negative factors. Parameter optimization can be accomplished on the small computer, offering ease of programming, data compatibility, and low cost. A previously proposed random-search algorithm ('random creep') was found to be very slow in convergence. A method is proposed (the 'random leap' algorithm) which starts in a global search mode and automatically adjusts step size to speed convergence. A FORTRAN executive program for the random-leap algorithm is presented which calls a user-supplied function subroutine. An example of a function subroutine is given which calculates maximum-likelihood estimates of receiver operating-characteristic parameters from binary response data. Other applications in parameter estimation, generalized least squares, and matrix inversion are discussed.

Curry, R. E.↗

Expansion and orthogonalization of measured modes for structure identification

The purpose was to investigate a new simultaneous expansion/orthogonalization method in comparison with two previously published expansion methods and a widely used orthogonalization technique. Each expansion method uses data from an analytical model of the structure to complete the estimate of the mode shape vectors. Berman and Nagy used Guyan expansion in their work with improving analytical models. In this method, modes are expanded one at a time, producing a set not orthogonal with respect to the mass matrix. Baruch and Bar Itzhack's optimal orthogonalization procedure was used to subsequently adjust the expanded modes. A second expansion technique was presented by O'Callahan, Avitabile, and Reimer and separately by Kammer. Again, modes are expanded individually and orthogonalized after expansion with the same optimal technique as above. Finally, a simultaneous expansion/orthogonalization method was developed from the orthogonal Procrustes problem of computational mathematics. In this method modes are optimally expanded as a set and orthogonal with respect to the mass matrix as a result. Two demonstation problems were selected for the comparison of the methods described. The first problem is an 8 degree of freedom spring-mass problem first presented by Kabe. Several conditions were examined for expansion method including the presence of errors in the measured data and in the analysis models. As a second demonstration problem, data from tests of laboratory scale model truss structures was expanded for system identification. Tests with a complete structure produced a correlated analysis model and the stiffness and mass matrices. Tests of various damaged configurations produced measured data for 6 modes at 14 dof locations.

Smith, Suzanne Weaver↗

Elimination sequence optimization for SPAR

SPAR is a large-scale computer program for finite element structural analysis. The program allows user specification of the order in which the joints of a structure are to be eliminated since this order can have significant influence over solution performance, in terms of both storage requirements and computer time. An efficient elimination sequence can improve performance by over 50% for some problems. Obtaining such sequences, however, requires the expertise of an experienced user and can take hours of tedious effort to affect. Thus, an automatic elimination sequence optimizer would enhance productivity by reducing the analysts' problem definition time and by lowering computer costs. Two possible methods for automating the elimination sequence specifications were examined. Several algorithms based on the graph theory representations of sparse matrices were studied with mixed results. Significant improvement in the program performance was achieved, but sequencing by an experienced user still yields substantially better results. The initial results provide encouraging evidence that the potential benefits of such an automatic sequencer would be well worth the effort.

Hogan, Harry A.↗

CFD Evaluation of a 3rd Generation LDI Combustor

An effort was undertaken to perform CFD analysis of fluid flow in Lean-Direct Injection (LDI) combustors with axial swirl-venturi elements for next-generation LDI-3 combustor design. The National Combustion Code (NCC) was used to perform non-reacting and two-phase reacting flow computations for a nineteen-element injector array arranged in a three-module, 7-5-7 element configuration. All computations were performed with a consistent approach of mesh-optimization, spray-modeling, ignition and kinetics-modeling with the NCC. Computational predictions of the aerodynamics of the injector were used to arrive at an optimal injector design that meets effective area and fuel-air mixing criteria. LDI-3 emissions (EINOx, EICO and UHC) were compared with the previous generation LDI-2 combustor experimental data at representative engine cycle conditions.

injectors↗

Optimization of thermal protection systems for the space shuttle vehicle. Volume 1: Final report

A study performed to continue development of computational techniques for the Space Shuttle Thermal Protection System is reported. The resulting computer code was used to perform some additional optimization studies on several TPS configurations. The program was developed in Fortran 4 for the CDC 6400, and it was converted to Fortran 5 to be used for the Univac 1108. The computational methodology is developed in modular fashion to facilitate changes and updating of the techniques and to allow overlaying the computer code to fit into approximately 131,000 octal words of core storage. The program logic involves subroutines which handle input and output of information between computer and user, thermodynamic stress, dynamic, and weight/estimate analyses of a variety of panel configurations. These include metallic, ablative, RSI (with and without an underlying phase change material), and a thermodynamic analysis only of carbon-carbon systems applied to the leading edge and flat cover panels. Two different thermodynamic analyses are used. The first is a two-dimensional, explicit precedure with variable time steps which is used to describe the behavior of metallic and carbon-carbon leading edges. The second is a one-dimensional implicity technique used to predict temperature in the charring ablator and the noncharring RSI. The latter analysis is performed simply by suppressing the chemical reactions and pyrolysis of the TPS material.

Source record↗

Shape optimization of pressure gradient microphones

Recently developed finite element computer programs were utilized to investigate the influence of the shape of a body on its scattering field with the aim of determining the optimal shape for a Pressure Gradient Microphone (PGM). Circular cylinders of various aspect ratios were evaluated to choose the length to diameter ratio best suited for a dual element PGM application. Alterations of the basic cylindrical shape by rounding the edges and recessing at the centerline were also studied. It was found that for a + or - 1 db deviation from a linear pressure gradient response, a circular cylinder of aspect ratio near 0.5 was most suitable, yielding a useful upper frequency corresponding to ka = 1.8. The maximum increase in this upper frequency limit obtained through a number of shape alterations was only about 20 percent. An initial experimental evaluation of a single element cylindrical PGM of aspect ratio 0.18 utilizing a piezoresistive type sensor was also performed and is compared to the analytical results.

Norum, T. D.↗

Solid-State Architecture Batteries for Enhanced Rechargeability and Safety (SABERS) Beyond Li-Ion: Technology to Enable Next-Generation Sustainable Electric

All-electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The primary barrier to overcome is developing an energy storage system that meets rigorous aerospace safety and performance criteria. The performance metrics for eVTOL vehicles are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for the safe operation of commercial electric aero vehicles. The SABERS concept proposes a battery that meets the critical performance criteria by developing a solid-state architecture battery utilizing a high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. This hybrid cathode will be developed using NASA-patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte will be used as a safe, non-flammable replacement for the highly flammable liquid organic electrolytes currently in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed in a serial stacking configuration to enable the dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, the optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150°C, providing the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. The SABERS team employed novel materials development, computational modeling, and design-of-experiments (DOE) optimization studies in their research. This presentation will show the results of these studies and demonstrate a feasible path for solid-state cells with a specific energy greater than 400 Wh/kg to enable electric aircraft.

Computational Modeling↗

Sizing of complex structure by the integration of several different optimal design algorithms

Practical design of large-scale structures can be accomplished with the aid of the digital computer by bringing together in one computer program algorithms of nonlinear mathematical programing and optimality criteria with weight-strength and other so-called engineering methods. Applications of this approach to aviation structures are discussed with a detailed description of how the total problem of structural sizing can be broken down into subproblems for best utilization of each algorithm and for efficient organization of the program into iterative loops. Typical results are examined for a number of examples.

Sobieszczanski, J.↗

Mascot - A new concept in guidance

Trajectory algorithm for complete trajectory from liftoff to landing with optimal control and onboard flight computer for use in manned space shuttle

Baker, C. D.↗

Analysis and design of a capsule landing system and surface vehicle control system for Mars exporation

The problems related to the design and control of a mobile planetary vehicle to implement a systematic plan for the exploration of Mars were investigated. Problem areas receiving attention include: vehicle configuration, control, dynamics, systems and propulsion; systems analysis; navigation, terrain modeling and path selection; and chemical analysis of specimens. The following specific tasks were studied: vehicle model design, mathematical modeling of dynamic vehicle, experimental vehicle dynamics, obstacle negotiation, electromechanical controls, collapsibility and deployment, construction of a wheel tester, wheel analysis, payload design, system design optimization, effect of design assumptions, accessory optimal design, on-board computer subsystem, laser range measurement, discrete obstacle detection, obstacle detection systems, terrain modeling, path selection system simulation and evaluation, gas chromatograph/mass spectrometer system concepts, chromatograph model evaluation and improvement and transport parameter evaluation.

Frederick, D. K.↗

Analysis and design of a capsule landing system and surface vehicle control system for Mars exploration

Investigation of problems related to the design and control of a mobile planetary vehicle to implement a systematic plan for the exploration of Mars has been undertaken. Problem areas receiving attention include: vehicle configuration, control, dynamics, systems and propulsion; systems analysis; terrain modeling and path selection; and chemical analysis of specimens. The following specific tasks have been under study: vehicle model design, mathematical modeling of a dynamic vehicle, experimental vehicle dynamics, obstacle negotiation, electromechanical controls, collapsibility and deployment, construction of a wheel tester, wheel analysis, payload design, system design optimization, effect of design assumptions, accessory optimal design, on-board computer sybsystem, laser range measurement, discrete obstacle detection, obstacle detection systems, terrain modeling, path selection system simulation and evaluation, gas chromatograph/mass spectrometer system concepts, chromatograph model evaluation and improvement.

Frederick, D. K.↗