SEARCH · Search NASA

Results for “Experimental evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Effect of Residual Noncondensables on Pressurization and Pressure Control of a Zero-Boil-Off Tank in Microgravity

The Zero-Boil-Off Tank (ZBOT) Experiment is a small-scale experiment that uses a transparent ventless Dewar and a transparent simulant phase-change fluid to study sealed tank pressurization and pressure control with applications to on-surface and in-orbit storage of propellant cryogens. The experiment will be carried out under microgravity conditions aboard the International Space Station in the 2014 timeframe. This paper presents preliminary results from ZBOT's ground-based research that focuses on the effects of residual noncondensable gases in the ullage on both pressurization and pressure reduction trends in the sealed Dewar. Tank pressurization is accomplished through heating of the test cell wall in the wetted and un-wetted regions simultaneously or separately. Pressure control is established through mixing and destratification of the bulk liquid using a temperature controlled forced jet flow with different degrees of liquid jet subcooling. A Two-Dimensional axisymmetric two-phase CFD model for tank pressurization and pressure control is also presented. Numerical prediction of the model are compared to experimental 1g results to both validate the model and also indicate the effect of the noncondensable gas on evolution of pressure and temperature distributions in the ullage during pressurization and pressure control. Microgravity simulations case studies are also performed using the validated model to underscore and delineate the profound effect of the noncondensables on condensation rates and interfacial temperature distributions with serious implications for tank pressure control in reduced gravity.

Marangoni and Natural Convection↗

NASA NTRS2017

Experimental Study into the Partitioning Behavior of Fluorine, Chlorine, Hydroxyl, and Sulfur (S2-) Between Apatite and a Synthetic Kreep Basalt Melt

The mineral apatite (Ca5 (PO4)3(F, Cl, OH)) is known for its ability to constrain the petrogenesis of the rock in which it is hosted and for its ubiquity throughout the Solar System, as it is found in lunar, martian, and terrestrial rocks alike (McCubbin et. al, 2015). The abundance of volatile elements, and for this particular study, the elevated abundance of sulfur (S2-) in high-Al basalt samples bearing apatite, could provide more insight for inquiries posed about the behavior of volatiles in lunar and martian magmatic systems (Boyce et. al, 2010). Oxygen fugacity will be an important parameter for these experiments, as the Moon, Mars, and Earth have different redox states (Herd, 2008). The objective of this experimental endeavor is to determine apatite-melt partition coefficients for the volatile elements (F-, Cl-, OH-, S2-) that make up the X-site (i.e., the typically monovalent anion site) in the mineral apatite in a lunar melt composition under lunar oxygen fugacity conditions approx.1-2 log units below the iron-wüstite buffer). All experiments will be conducted at NASA, Johnson Space Center in the High Pressure Experimental Petrology Laboratory. In order to conduct apatite-melt partition experiments with oxygen fugacity as an additional parameter, we will create a synthetic mix of the lunar KREEP basalt 15386, a sample retrieved during Apollo 15 that is believed to represent an indigenous volcanic melt derived from the lunar interior (Rhodes, J.M et. al, 2006). Other geochemically significant elements including C, Co, Ni, Mo, and rare earth elements will be included in the mix at trace abundances in order to assess their partitioning behavior without effecting the overall behavior of the system. The synthetic mix will then be loaded into a piston cylinder, an apparatus used to simulate high-pressure/high-temperature conditions of planetary interiors, and exposed to 0.5 GPa of pressure, the pressure observed in the upper mantle of the Moon, and heated to the melting temperature of the materials. To make sure crystals grow large enough for the necessary analyses, the sample will be kept at the crystallization temperature for 8 hours. This extended run time should also allow the sample to achieve a steady state which is necessary to accurately assess the partitioning of these elements between apatite and melt. The results from this experimental study will allow us to determine the fate of F-, Cl-, OH-, and S2- during the magmatic evolution of the Moon.

Turner, Amber↗

NASA NTRS2017

An Experimental Flow-Through Assessment of Acidic Fe/Mg Smectite Formation on Early Mars

Orbital observations have detected the phyllosilicate smectite in layered material hundreds of meters thick, intracrater depositional fans, and plains sediments on Mars; however, the detection of carbonate deposits is limited. Instead of neutral/alkaline conditions during the Noachian, early Mars may have experienced mildly acidic conditions derived from volcanic acid-sulfate solutions that allowed Fe/Mg smectite formation but prevented widespread carbonate formation. The detection of acid sulfates (e.g., jarosite) associated with smectite in Mawrth Vallis supports this hypothesis. Previous work demonstrated smectite (saponite) formation in closed hydrologic systems (batch reactor) from basaltic glass at pH 4 and 200°C (Peretyazhko et al., 2016 GCA). This work presents results from alteration of basaltic glass from alkaline to acidic conditions in open hydrologic systems (flow-through reactor). Preliminary experiments exposed basaltic glass to deionized water at 190°C at 0.25 ml/min where solution pH equilibrated to 9.5. These initial high pH experiments were conducted to evaluate the flow-through reactor system before working with lower pHs. Smectite at this pH was not produced and instead X-ray diffraction results consistent with serpentine was detected. Experiments are in progress exposing basaltic glass from pH 8 down to pH 3 to determine what range of pHs could allow for smectite formation in this experimental opensystem. The production of smectite under an experimental open-system at low pHs if successful, would support a significant paradigm shift regarding the geochemical evolution of early Mars: Early Mars geochemical solutions were mildly acidic, not neutral/alkaline. This could have profound implications regarding early martain microbiology where acid conditions instead of neutral/alkaline conditions will require further research in terrestrial analogs to address the potential for biosignature preservation on Mars.

Sutter, Brad↗

NASA NTRS2020

Turbulent mixing in supercritical jets: effect of compressibility factor and inflow condition

Fuel injection and turbulent mixing at supercritical pressures determines ignition and combustion in numerous engineering applications. Flow evolution under such conditions is characterized by strong non-linear coupling between dynamics, transport coefficients, and thermodynamics. Experimental studies observe that the jets injected at supercritical pressures exhibit significantly different dynamics from the jets at subcritical conditions, owing to the lack of distinct liquid and gas phases in supercritical state. Thus, the averaged flow quantities such as the potential core length, jet spatial growth rate and velocity decay profiles differ in the two conditions, resulting in different mixed-fluid distributions. In this study, turbulent jet direct numerical simulations (DNS) are performed to examine the variations in flow statistics between injection of Nitrogen (N₂) in Nitrogen (N₂) at both subcritical (perfect-gas) and supercritical conditions. In all cases, isothermal round jets at Reynolds number (Re_{D}), based on jet diameter (D) and jet orifice velocity (U₀), of 5000 are considered. For mixing analyses, a passive scalar transported with the flow is examined.

Sharan, Nek↗

DOE OSTI2025

Effect of Loading Frequency on Fatigue Behavior of Additively Manufactured Short Fiber Thermoplastics via Infrared Thermography

Fracture, Fatigue, Failure, Damage Evolution and Thermomechanics & Infrared Imaging, Volume 4 of the Proceedings of the 2025 SEM Annual Conference & Exposition on Experimental and Applied Mechanics, the fourth volume of five from the Conference, brings together contributions to this important area of research and engineering. The collection presents early findings and case studies on a wide range of areas, including: • 3D Deformation and Failure • In-situ Techniques and Microscale Effects on Mechanical Behavior • Vibration and Cyclic Fatigue • Integration of Models and Experiments • Interface-Mediated Damage and Failure • Fracture and Fatigue in Brittle Materials • Material Characterizations Using Thermography • Fatigue, Damage & Fracture Evaluation Using Infrared Thermography

Pathak, Pharindra [Auburn University]↗

DOE OSTI2022

Persistent exchange splitting in the chiral helimagnet $\mathrm{Cr}_{1/3}\mathrm{NbS}_2$

Here, using high-resolution angle-resolved photoemission spectroscopy and ab initio calculation, we systematically investigate the electronic structure of the chiral helimagnet Cr 1/3 NbS 2 and its temperature evolution. The comparison with NbS 2 suggests that the electronic structure of Cr 1/3 NbS 2 is strongly modified by the intercalation of Cr atoms. Our ab initio calculation, consistent with experimental results, suggests strong hybridization between Nb- and Cr-derived states near the Fermi level. In the chiral helimagnetic state (below the Curie temperature, T c ), we observe exchange splitting of the energy bands crossing the Fermi level, which follows the temperature evolution of the magnetic moment, suggesting a strong interaction between the conduction electrons and Cr spin moments. Interestingly, the exchange splitting persists far above T c with weak temperature dependence, in drastic contrast to the itinerant ferromagnetism described by the Stoner model, indicating the existence of short-range magnetic order. Our results provide important insights into the interplay between the electronic structure and magnetism in Cr 1/3 NbS 2 , which is helpful for understanding the microscopic mechanism of chiral helimagnetic ordering.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2021

White paper on NIF Discovery Science and frontier regimes of HEDP

Over the past two decades, experimental capabilities at high energy density (HED) facilities such as the National Ignition Facility (NIF), Omega, and Omega EP lasers, and the Z pulsed power facility are able to make precision measurements of fundamental quantities such as equations of state (EOS), material phase, opacities, and ionization levels Z. Flow based quantities are also being studied, such as hydrodynamic instabilities, evolution into turbulence, turbulent dynamo magnetic field amplification, magnetic reconnection; plasma instabilities, plasma wakefield particle acceleration; and relativistic plasma phenomena, such as (e + ,e - ) pair creation. Experimental regimes can be created that reproduce conditions relevant to planetary and exoplanet interiors, stellar interiors, the interiors of brown dwarfs, and the envelope conditions of white dwarf stars. Diagnostic techniques have been developed hand in hand with these new experimental regimes that can be accessed. In this white paper, a brief summary of key experimental achievements from the NIF Discovery Science (basic science) program will be presented; followed by a discussion of current challenges, needs, and potential paths forward.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2017

Evolution of Morphological and Physical Properties of Laboratory Interstellar Organic Residues with Ultraviolet Irradiation

Refractory organic compounds formed in molecular clouds are among the building blocks of the solar system objects and could be the precursors of organic matter found in primitive meteorites and cometary materials. However, little is known about the evolutionary pathways of molecular cloud organics from dense molecular clouds to planetary systems. In this study, we focus on the evolution of the morphological and viscoelastic properties of molecular cloud refractory organic matter. We found that the organic residue, experimentally synthesized at ∼10 K from UV-irradiated H{sub 2}O-CH{sub 3}OH-NH{sub 3} ice, changed significantly in terms of its nanometer- to micrometer-scale morphology and viscoelastic properties after UV irradiation at room temperature. The dose of this irradiation was equivalent to that experienced after short residence in diffuse clouds (≤10{sup 4} years) or irradiation in outer protoplanetary disks. The irradiated organic residues became highly porous and more rigid and formed amorphous nanospherules. These nanospherules are morphologically similar to organic nanoglobules observed in the least-altered chondrites, chondritic porous interplanetary dust particles, and cometary samples, suggesting that irradiation of refractory organics could be a possible formation pathway for such nanoglobules. The storage modulus (elasticity) of photo-irradiated organic residues is ∼100 MPa irrespective of vibrational frequency, a value that is lower than the storage moduli of minerals and ice. Dust grains coated with such irradiated organics would therefore stick together efficiently, but growth to larger grains might be suppressed due to an increase in aggregate brittleness caused by the strong connections between grains.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS2022

Nonlinear Evolution of Instability in a Laminar Separation Bubble at Hypersonic Mach Number

The development of both convective stationary perturbation as well as global instabilities in the vicinity of a laminar separation bubble above an axisymmetric compression corner in a hypersonic flow is investigated using numerical simulations. The flow configuration of primary interest corresponds to the cone-cylinder-flare model used in experimental measurements in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. For a flare angle of 10 degrees and a unit Reynolds number of 11.5 x 10 6 m -1 , their surface flow visualizations identified the presence of streamwise elongated thermal streaks near the reattachment position and the dominant azimuthal spacing between the streaks was determined to be approximately 10 degrees (i.e., an azimuthal mode number of 36). Previous linear stability analyses predicted that the amplification characteristics of small amplitude, unsteady, convective instabilities within this flow were consistent with the surface pressure fluctuations measured in the experiment. However, their accompanying analysis of global instabilities had found the separation bubble to be weakly unstable at the 10 degrees flare angle, with the most unstable global mode corresponding to a stationary disturbance with an azimuthal wavenumber of m ≈ 5, which was well below the measured wavenumber of m = 36. Besides confirming the presence of the global instability at these flow conditions, the present numerical simulations quantify the details of the stationary equilibrium state associated with the supercritical bifurcation resulting from the nonlinear saturation of the unstable global mode. Although velocity perturbations associated with the saturated global mode are dominated by the fundamental spanwise wavelength associated with the linear global instability, the surface heat flux downstream of reattachment is dominated by m = 36 in agreement with experimental measurements. However, the shorter wavelength peak ( m = 36) in the azimuthal spectrum is not manifested as streaks with an azimuthal spacing of 10 degrees. An additional simulation of the combined evolution of both unsteady convective and global instabilities indicates that the nonlinear interactions between a broadband spectrum of oblique Mack’s first mode instabilities generate stationary vortex modes with a higher dominant wavenumber ( m = 60) as that observed in the experiments. Additional analyses are performed to predict the global mode behavior at other flare angles and how it differs from the convective centrifugal instability due to concave streamline curvature over the compression corner.

High speed flow↗

DOE OSTI2024

Full-field quantitative visualization of shock-driven pore collapse and failure modes in PMMA

The dynamic collapse of pores under shock loading is thought to be directly related to hot spot generation and material failure, which is critical to the performance of porous energetic and structural materials. However, the shock compression response of porous materials at the local, individual pore scale is not well understood. This study examines, quantitatively, the collapse phenomenon of a single spherical void in PMMA at shock stresses ranging from 0.4 to 1.0 GPa. Using a newly developed internal digital image correlation technique in conjunction with plate impact experiments, full-field quantitative deformation measurements are conducted in the material surrounding the collapsing pore for the first time. The experimental results reveal two failure mode transitions as shock stress is increased: (i) the first in situ evidence of shear localization via adiabatic shear banding and (ii) dynamic fracture initiation at the pore surface. Numerical simulations using thermo-viscoplastic dynamic finite element analysis provide insights into the formation of adiabatic shear bands (ASBs) and stresses at which failure mode transitions occur. Further numerical and theoretical modeling indicates the dynamic fracture to occur along the weakened material inside an adiabatic shear band. Finally, analysis of the evolution of pore asymmetry and models for ASB spacing elucidate the mechanisms for the shear band initiation sites, and elastostatic theory explains the experimentally observed ASB and fracture paths based on the directions of maximum shear.

42 ENGINEERING↗

DOE OSTI2017

Experimental and numerical analysis of the performance and wake of a scale–model horizontal axis marine hydrokinetic turbine

Here, this paper presents an experimental and numerical study of a scale-model Horizontal Axis Hydrokinetic Turbine (HAHT). The model turbine is based on the U.S. Department of Energy Reference Model 1 (RM1), with the blade geometry modified to reproduce the design C p –TSR performance curve of the RM1 at the flume scale Reynolds numbers (5 × 10 4 –10 × 10 5 ). The performance and wake structure of a 45:1 scale turbine were measured using a load cell (torque applied on shaft) and a magnetic angular encoder (rotor rpm), and by planar particle image velocimetry, respectively. The details of the rotor flow field and three-dimensional wake evolution are analyzed from the numerical solution of the RANS equations solved around a computational model of the turbine. The comparison of experimental and numerical results highlights the strengths and limitations of the experimental and numerical analyses in the characterization of HAHT. Useful guidelines for developing experimental flume scale data and using them for validating numerical tools, as well as for performing a similar type of analysis and design validation of full scale devices as pilot projects start to go in the water in the United States, are provided.

13 HYDRO ENERGY↗

NASA NTRS2022

Nonlinear Evolution of Instabilities in a Laminar Separation Bubble at a Hypersonic Mach Number

Hypersonic flow↗

DOE OSTI2017

Predictive characterization of aging and degradation of reactor materials in extreme environments. Final report, December 20, 2013 - September 20, 2017

Understanding of reactor material behavior in extreme environments is vital not only to the development of new materials for the next generation nuclear reactors, but also to the extension of the operating lifetimes of the current fleet of nuclear reactors. To this end, this project conducted a suite of unique experimental techniques, augmented by a mesoscale computational framework, to understand and predict the long-term effects of irradiation, temperature, and stress on material microstructures and their macroscopic behavior. The experimental techniques and computational tools were demonstrated on two distinctive types of reactor materials, namely, Zr alloys and high-Cr martensitic steels. These materials are chosen as the test beds because they are the archetypes of high-performance reactor materials (cladding, wrappers, ducts, pressure vessel, piping, etc.). To fill the knowledge gaps, and to meet the technology needs, a suite of innovative in situ transmission electron microscopy (TEM) characterization techniques (heating, heavy ion irradiation, He implantation, quantitative small-scale mechanical testing, and various combinations thereof) were developed and used to elucidate and map the fundamental mechanisms of microstructure evolution in both Zr and Cr alloys for a wide range environmental boundary conditions in the thermal-mechanical-irradiation input space. Knowledge gained from the experimental observations of the active mechanisms and the role of local microstructural defects on the response of the material has been incorporated into a mathematically rigorous and comprehensive three-dimensional mesoscale framework capable of accounting for the compositional variation, microstructural evolution and localized deformation (radiation damage) to predict aging and degradation of key reactor materials operating in extreme environments. Predictions from this mesoscale framework were compared with the in situ TEM observations to validate the model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

How are Heterogeneous Nucleation Rate Observations Influenced by Instrument Resolution?

Experimental measurements of the heterogeneous nucleation rate rely on counting the number of nuclei with time. However, the size of a thermodynamically stable nucleus is often a few nanometers in diameter and is below the resolution of most (in situ) measurement techniques that provide a statistically valid sample. Due to the finite resolution of the instruments and analysis methods, it is challenging to capture the incipient nuclei and the subsequent evolution of nuclei density over time. In this work, we demonstrate the impact of instrument resolution on observed nuclei densities by comparing numerical modeling with experimental results. Further, to achieve this, we implemented heterogeneous nucleation within the pore-scale reactive transport modeling framework using classical nucleation theory (CNT). We compared the modeling results with nucleation rates measured using X-ray nanotomography (XnT) and evaluated how these impact the apparent values of the prefactor and interfacial energy based on CNT and the crystal growth rate. Specifically, we applied a resolution threshold (artificial resolution limit) in the model during nuclei counting to resemble an experimental resolution, ranging from 15 to 500 nm. The findings reveal that the instrument resolution significantly impacts the apparent prefactor and interfacial energy. Both apparent prefactor and interfacial energy decrease with a decrease in the instrument resolution. While deviation in the prefactor due to resolution is anticipated, those in the interfacial energy are unexpected. The approach described here allows one to correct apparent nucleation rates that depend on the instrument’s resolution to derive “intrinsic” CNT parameters for the prefactor and interfacial energy.

47 OTHER INSTRUMENTATION↗

DOE OSTI2023

CrysFieldExplorer : rapid optimization of the crystal field Hamiltonian

A new approach to the fast optimization of crystal electric field (CEF) parameters to fit experimental data is presented. This approach is implemented in a lightweight Python-based program, CrysFieldExplorer. The main novelty of the method is the development of a unique loss function, referred to as the spectrum characteristic loss (L Spectrum ), which is based on the characteristic polynomial of the Hamiltonian matrix. Particle swarm optimization and a covariance matrix adaptation evolution strategy are used to find the minimum of the total loss function. It is demonstrated that CrysFieldExplorer can perform direct fitting of CEF parameters to any experimental data such as a neutron spectrum, susceptibility or magnetization measurements etc. CrysFieldExplorer can handle a large number of non-zero CEF parameters and reveal multiple local and global minimum solutions. Crystal field theory, the loss function, and the implementation and limitations of the program are discussed within the context of two examples.

42 ENGINEERING↗

DOE OSTI2018

Isotropic neutrino flux from supernova explosions in the universe

Neutrinos of all types are emitted from the gravitational collapse of massive star cores, and have been amassed in the Universe throughout the history of evolution of galaxies. The isotropic and stable flux of these neutrinos is a source of information on the spectra of neutrinos from individual supernovae and on their redshift distribution. The prospects for detecting the isotropic neutrino flux with the existing and upcoming experimental facilities and the current upper limits are discussed in this paper.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2026

Effect of macroscopic surface defects on dynamic damage: An experimental and numerical study

This study examines the impact of macroscopic surface defects on the dynamic ductile damage behavior of polycrystalline metals using plate-impact experiments. Defects of various shapes (flat, round, and point) were manufactured on the free or impact surfaces of annealed copper specimens. The experiments were diagnosed with photon Doppler velocimetry measurements and soft recovery techniques. The experimental results revealed that defect shape and location significantly affect velocity–time profiles and void distribution. In order to understand the dynamics of shock propagation and corresponding ductile damage evolution within the target specimens, the impact experiments were modeled with a calibrated Tepla model, a dynamic ductile damage model for polycrystalline metals [Nguyen et al., Int. J. Solids Struct. 329, 113833 (2026)]. Overall, our resulting simulated velocity showed good agreement with measured velocity, and our simulated porosity distributions qualitatively matched experimental data. Based on our simulation results, defects on the free surface were found to distort rarefaction waves and therefore the corresponding spall planes. On the other hand, defects on the impact surface generated a delayed shock when the flyer plate and the defected target area were in contact, leading to distortion of the spall plane. The distortion of the spall plane resulted in a non-uniform distribution of voids within the defected specimens. Lastly, we examined the role of local work hardening due to the defect manufacturing process on the velocity and porosity distribution, using Tepla simulations with a simplified representation of local hardening. This investigation highlights the importance of defect geometry, location, and local hardening associated with defect generation in dynamic ductile damage processes.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Charge breeders: Development of diagnostic tools to probe the underlying physics

Charge breeders were developed more than 20 years ago in the context of radioactive ion beam (RIB) production. The main goal is to boost the charge state of a singly charged RIB to a higher value matching the A/Q of a post-accelerator. In that way, the RIB produced at some tens of keV can efficiently be accelerated to energies in a range of few MeV/u up to several tens of MeV/u, which is of interest for nuclear structure and nuclear astrophysics experiments. Two families of charge breeders have been developed: one based on Electron Cyclotron Resonance Ion Sources (ECRISs) suitable for Continuous Wave (CW) operation and another built around Electron Beam Ion Sources (EBISs) used for pulsed post-accelerators. For many years, experimental studies have been carried out to enhance the charge breeding process and improve the extracted beam quality, i.e., purity, intensity, emittance, and time structure. The evolution of the charge breeders is also closely related to the emergence of new facilities delivering even more exotic beams. Diagnostic tools, such as Faraday cups, beam profile monitors, and emittance scanners, are mandatory to tune the machines and evaluate their performances. However, to go beyond that, a better understanding of plasma physics (in ECRIS) and electron-ion interactions (in EBIS), as well as the 1+ beam characteristics, for instance, energy spread transverse emittance, is needed. Therefore, simulation codes modeling the physics phenomena in both type of charge breeders were developed to support the understanding of experimental outputs and to gain insights into non-observable parameters. Nevertheless, more sophisticated diagnostic tools are required to improve the charge breeding performance and to extend the potential applications toward new RIB facilities. This Review will present the two kinds of charge breeders and their technical evolutions. It will review the diagnostic tools and simulation codes employed for operation and evaluation of the internal physics processes.

47 OTHER INSTRUMENTATION↗