Search NASA⌕ Search

SEARCH · Search NASA

Results for “INGESTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Piezoelectric Pushers Suppress Vibrations

Vibration-suppressing control systems including piezoelectric actuators undergoing development. Small, lightweight, and rugged. Requires simpler electronic control subsystems and does not require large electromagnet coils. Continues to provide support and some passive damping even when electronic control subsystems or power supplies fail. Intended primarily to enhance safety and prevent damage in rotating machinery by sensing and counteracting vibrations. Useful in suppressing unpredictable vibrations caused by changes in loads, losses of rotating components and consequent imbalances in rotors, and ingestion of foreign objects into turbines.

Kascak, Albert F.↗

Engine inlet distortion in a 9.2 percent scale vectored thrust STOVL model in ground effect

Advanced Short Takeoff/Vertical Landing (STOVL) aircraft which can operate from remote locations, damaged runways, and small air capable ships are being pursued for deployment around the turn of the century. To achieve this goal, NASA Lewis Research Center, McDonnell Douglas Aircraft, and DARPA defined a cooperative program for testing in the NASA Lewis 9- by 15-foot low speed wind tunnel (LSWT) to establish a database for hot gas ingestion, one of the technologies critical to STOVL. Results are presented which show the engine inlet distortions (both temperature and pressure) in a 9.2 percent scale vectored thrust STOVL model in ground effects. Results are shown for the forward nozzle splay angles of 0 degrees, -6 degrees, and 18 degrees. The model support system had 4 degrees of freedom, heated high pressure air for nozzle flow, and a suction system exhaust for inlet flow. The headwind (freestream) velocity was varied from 8 to 23 knots.

Johns, Albert L.↗

A numerical parametric study of a scramjet inlet in a Mach 6 arc heated test facility

A numerical study of the NASA Langley Arc Heated Scramjet Test Facility (AHSTF) is reported. The facility test flow through the Mach 6 quasi-two-dimensional nozzle was computed, and the flow through the Langley parametric inlet was calculated using different regions of the computed facility nozzle exit flow as inflow, exploring in more detail the effect of boundary layer ingestion on inlet performance. The potential advantage of using a quasi-two-dimensional nozzle in the Langley AHSTF versus the square cross-sectioned nozzle currently used for Scramujet engine tests is explored in terms of resulting inlet performance.

Sekar, B.↗

Engine inlet distortion in a 9.2 percent scaled vectored thrust STOVL model in ground effect

Advanced Short Takeoff/Vertical Landing (STOVL) aircraft which can operate from remote locations, damaged runways, and small air capable ships are being pursued for deployment around the turn of the century. To achieve this goal, a cooperative program has been defined for testing in the NASA Lewis 9- by 15-foot Low Speed Wind Tunnel (LSWT) to establish a database for hot gas ingestion, one of the technologies critical to STOVL. This paper presents results showing the engine inlet distortions (both temperature and pressure) in a 9.2 percent scale Vectored Thrust STOVL model in ground effects. Results are shown for the forward nozzle splay angles of 0, -6, and 18 deg. The model support system had 4 deg of freedom, heated high pressure air for nozzle flow, and a suction system exhaust for inlet flow. The headwind (freestream) velocity was varied from 8 to 23 kn.

Johns, Albert L.↗

A computational study of the impingement region of an unsteady subsonic jet

Vertical/Short Take-Off and Landing (V/STOL) aircraft may encounter operating difficulties while hovering near the ground. Lift loss, hot gas and debris ingestion, and landing surface damage are some of the potential problems which can result from the interaction of the propulsive jets with the airframe and ground. The purpose of the present work is to develop a detailed understanding of a flowfield, a jet exiting from a flat plate impacting a ground plane, that contains much of the essential physics of the complex flows encountered by V/STOL aircraft in hover. To achieve this, a high-resolution time-accurate numerical simulation of the impinging jet flow was performed. The numerical simulation is based on the solution of the laminar compressible Navier-Stokes equations using the Beam-Warming algorithm. Complex start-up and periodic jet and jet-induced vortex structures were captured, including the formation of primary and secondary jet-induced vortices and wall-jet separation. The formation and development of these phenomena are supported by experimental measurements and smoke visualization. Results are compared with appropriate experiments.

Jalamani, Zakaria A.↗

A rotating hot-wire technique for spatial sampling of disturbed and manipulated duct flows

A duct flow spatial sampling technique, in which an X-wire probe is rotated about the center of a cylindrical test section at a radius equal to one-half that of the test section in order to furnish nearly instantaneous multipoint measurements of the streamwise and azimuthal components, is presently evaluated in view of the control of flow disturbances downstream of various open inlet contractions. The effectiveness of a particular contraction in controlling ingested flow disturbances was ascertained by artificially introducing disturbances upstream of the contractions; control effectiveness if found to be strongly dependent on inlet contraction, with consequences for the reduction of passing-blade frequency noise during gas turbine engine ground testing.

Wark, C. E.↗

A numerical study of the effects of reverse sweep on a scramjet inlet performance

A comparative numerical study of performance parameters of a similar and an opposite sweep sidewall compression inlet is made. The focus of the study is the investigation of the impact of alternate backward-forward sweep on the compression sidewalls as opposed to back-ward sweep on all the sidewalls. Two equivalent scramjet inlet configurations are designed for this purpose. These inlets have the same wetted areas of compression and expansion and same height and width; but in one inlet all the compression surface are swept back (similar sweep inlet) whereas in the other inlet, alternate surfaces are swept backward and forward (opposite sweep inlet). The cowl closure in both cases begins at the start of the throat region. A three-dimensional Navier-Stokes code is used to calculate the flow through these inlets. Results of these calculations are used to compare the two designs for their performance and flow quality. Effects of boundary- layer ingestion on the performance and overall flow features are also investigated.

Kumar, Ajay↗

Simulation evaluation of transition and hover flying qualities of a mixed-flow, remote-lift STOVL aircraft

Using a generalized simulation model developed for piloted evaluations of STOVL aircraft, an initial fixed-base simulation of a mixed-flow, remote-lift configuration has been completed. Objectives were to evaluate the integration of the aircraft's flight and propulsion controls to achieve good flying qualities throughout the low-speed flight envelope; to determine control power used during transition, hover, and vertical landing; and to evaluate the transition flight envelope considering the influence of thrust deflection of the remote-lift component. Pilots' evaluations indicated that Level 1 flying qualities could be achieved for deceleration to hover in instrument conditions, for airfield landings, and for recovery to a small ship when attitude and velocity stabilization and command augmentation control modes were provided. Level 2 flying qualities were obtained for these same tasks when only the attitude command mode was used, leaving the pilot to perform the task of thrust management required to control the flight-path and speed in transition and the horizontal and vertical translational velocities in hover. Thrust margins were defined for vertical landing as a function of ground effect and hot-gas ingestion.

Franklin, James A.↗

Composite-Material Airflow Vane

"Alpha/beta" lightweight instrumentation vanes made of composite of phenolic, epoxy, and fiberglass stronger and more accurate than conventional vanes made partly of balsa wood. Absorbs little or no moisture and provides more repeatable measurements. Because weight same as balsa vanes, no instrumentation changes needed. If vane breaks away from stem, not likely to damage aircraft engine if ingested; more likely crumbles into low-density particles that pass through without causing harm.

Vranas, Thomas L.↗

A numerical study of the hot gas environment around a STOVL aircraft in ground proximity

The development of Short Takeoff Vertical Landing (STOVL) aircraft has historically been an empirical- and experienced-based technology. A 3-D turbulent flow CFD code was used to calculate the hot gas environment around an STOVL aircraft operating in ground proximity. Preliminary calculations are reported for a typical STOVL aircraft configuration to identify key features of the flow field, and to demonstrate and assess the capability of current 3-D CFD codes to calculate the temperature of the gases ingested at the engine inlet as a function of flow and geometric conditions.

Vanoverbeke, Thomas J.↗

Forces and pressures induced on circular plates by a single lifting jet in ground effect

NASA Ames is conducting a program to develop improved methods for predicting suckdown and hot-gas ingestion on jet V/STOL aircraft when they are in ground effect. As part of that program a data base is being created that provides a systematic variation of parameters so that current empirical prediction procedures can be modified. The first series of tests in this program is complete. This report is one of three that presents the data obtained from tests conducted at Lockheed Aeronautical Systems - Rye Canyon Facility and the High Bay area of the 40 by 80 foot Wind Tunnel at Ames Research Center. Suckdown on two circular plates is examined.

Bellavia, David C.↗

Suckdown, fountain lift, and pressures induced on several tandem jet V/STOL configurations

As part of a program to improve the methods for predicting the suckdown and hot gas ingestion for jet V/STOL aircraft in ground effect, a data base is being created that provides a systematic variation of parameters so that a new empirical prediction procedure can be developed. The first series of tests in this program was completed. Suckdown, fountain lift, and pressures induced on several two-jet V/STOL configurations are described. It is one of three reports that present the data obtained from tests conducted at Lockheed Aeronautical Systems-Rye Canyon Facility and in the High Bay area of the 40 by 80 foot wind tunnel complex at NASA Ames Research Center.

Bellavia, David C.↗

SEAPAK user's guide, version 2.0. Volume 1: System description

The SEAPAK is a user interactive satellite data analysis package that was developed for the processing and interpretation of Nimbus-7/Coastal Zone Color Scanner (CZCS) and the NOAA Advanced Very High Resolution Radiometer (AVHRR) data. Significant revisions were made to version 1.0 of the guide, and the ancillary environmental data analysis module was expanded. The package continues to emphasize user friendliness and user interactive data analyses. Additionally, because the scientific goals of the ocean color research being conducted have shifted to large space and time scales, batch processing capabilities for both satellite and ancillary environmental data analyses were enhanced, thus allowing large quantities of data to be ingested and analyzed in background.

Mcclain, Charles R.↗

SEAPAK user's guide, version 2.0. Volume 2: Descriptions of programs

The SEAPAK is a user-interactive satellite data analysis package that was developed for the processing and interpretation of Nimbus-7/Coastal Zone Color Scanner (CZCS) and the NOAA Advanced Very High Resolution Radiometer (AVHRR) data. Significant revisions were made since version 1.0, and the ancillary environmental data analysis module was greatly expanded. The package continues to be user friendly and user interactive. Also, because the scientific goals of the ocean color research being conducted have shifted to large space and time scales, batch processing capabilities for both satellite and ancillary environmental data analyses were enhanced, thus allowing for large quantities of data to be ingested and analyzed.

Mcclain, Charles R.↗

Numerical investigations in three-dimensional internal flows

The present study is a preliminary investigation into the behavior of the flow within a 28 degree total geometric turning angle hypothetical Mach 10 inlet as calculated with the full three-dimensional Navier-Stokes equations. Comparison between the two-dimensional and three-dimensional solutions have been made. The overall compression is not significantly different between the two-dimensional and center plane three dimensional solutions. Approximately one-half to two-thirds of the inlet flow at the exit of the inlet behave nominally two-dimensionally. On the other hand, flow field non-uniformities in the three-dimensional solution indicate the potential significance of the sidewall boundary layer flows ingested into the inlet. The tailoring of the geometry at the inlet shoulder and on the cowl obtained in the two-dimensional parametric design study have also proved to be effective at controlling the boundary layer behavior in the three-dimensional code. The three-dimensional inlet solution remained started indicating that the two-dimensional design had a sufficient margin to allow for three-dimensional flow field effects. Although confidence is being gained in the use of SCRAM3D (three-dimensional full Navier-Stokes code) as applied to similar flow fields, the actual effects of the three-dimensional flow fields associated with sidewalls and wind tunnel installations can require verification with ground-based experiments.

Rose, William C.↗

Viscous drag reduction via surface mass injection

Slot injection systems on the surfaces of aerodynamic bodies have been noted to consistently furnish substantial local skin friction reductions which are predictable on the basis of current numerical methods. Only crude systems studies, however, have been thus far completed. The most common configuration for slot ingestion in the literature involves tangential injection of air along a two-dimensional surface on which air constitutes the mainstream flow; attention is presently given to slot injection in low-speed and high-speed flows, as well as a discussion of aircraft applications and an evaluation of prospective possibilities for practical drag-reduction systems.

Hefner, Jerry N.↗

High rate science data handling on Space Station Freedom

A study by NASA's User Information System Working Group for Space Station Freedom (SSF) has determined that the proposed onboard Data Management System, as initially configured, will be incapable of handling the data-generation rates typical of numerous scientific sensor payloads; many of these generate data at rates in excess of 10 Mbps, and there are at least four cases of rates in excess of 300 Mbps. The SSF Working Group has accordingly suggested an alternative conceptual architecture based on technology expected to achieve space-qualified status by 1995. The architecture encompasses recorders with rapid data-ingest capabilities and massive storage capabilities, optical delay lines allowing the recording of only the phenomena of interest, and data flow-compressing image processors.

Handley, Thomas H., Jr.↗

Numerical study of twin-jet impingement upwash flow

Two horizontally spaced jets impinging normally on a flat surface create a fountain upwash flow due to the collision of the radially flowing wall jets. This fountain flow is of importance to the dynamics and propulsion of STOVL aircraft. The fountain flow influences the lift forces on the aircraft and the ingestion of hot gases and debris by the engine inlet. In this paper, a multigrid based finite-difference numerical procedure has been applied to solve the equations governing this three-dimensional flow. The standard k-epsilon turbulence model has been used. Comparisons with experimental data reveal that while the mean velocities are predicted with reasonable accuracy, the turbulent kinetic energies are seriously in error. The reasons for this discrepancy could be the intense unsteadiness and large-scale structures of the flow in the near-wall region, which cannot be captured well by any Reynolds-averaged turbulence model.

Pegues, W. J.↗