Search NASA⌕ Search

SEARCH · Search NASA

Results for “Image Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Characterization of Roughness, Porosity and Thermal Resistances of Continuous Casting Mold Slag Layers Devitrified and Crystallized in Laboratory

This paper presents an experimental investigation about the variation, with temperature, of surface roughness, porosity, degree of crystallization and microstructure, occurring in solid layers of a commercial mold powder slag used for casting medium carbon steel thin slabs. Characterization is done with samples devitrified and crystallized at 698 K, 823 K, 898 K and 973 K (425 °C, 550 °C, 625 °C and 700 °C) for 10,800 seconds, in the furnace of a high-temperature confocal laser scanning microscope. As well as, with slag disks devitrified non-isothermally in a heat flow apparatus based on the application of Fourier's law in steady state conditions, where the high temperature surface is maintained at selected values, between 927 K and 1241 K (654 °C and 968 °C). Surface roughness and porosity determinations are performed by image analysis of confocal laser scanning and scanning electron micrographs, respectively. For the time considered and temperatures ≥ 823 K (550 °C) the slag crystallizes completely, and variations of roughness and porosity with temperature are associated with changes in size and packing of the primary crystalline-phase grains. Crystallization induced porosity is significant and causes slag layer expansion. Hence crystallization does not lead to gap formation with a neighboring surface (e.g., mold wall) by shrinkage. Instead, surface separation arises from development of roughness, and measurements with the heat flow apparatus confirm that interfacial thermal resistance between a slag layer and a metallic wall can be estimated from the sum of the means of maximum peak to valley height of their surfaces. Furthermore, the results establish that slag layers roughness and porosity increase with temperature and reveal effective thermal conductivities in the range of ~ 0.3 to ~ 0.5 W/m K. Low effective thermal conductivities must be a consequence of porous bands, whose porosity depends on temperature and reaches values as high as ~ 0.20 and ~ 0.50.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Characterization of the porous structures of the green body and sintered biomedical titanium scaffolds with micro-computed tomography

The present research was aimed at gaining an understanding of the porous structure changes from the green body through water leaching and sintering to titanium scaffolds. Micro-computed tomography (micro-CT) was performed to generate 3D models of titanium scaffold preforms containing carbamide space-holding particles and sintered scaffolds containing macro- and micro-pores. The porosity values and structural parameters were determined by means of image analysis. The result showed that the porosity values, macro-pore sizes, connectivity densities and specific surface areas of the titanium scaffolds sintered at 1200 °C for 3 h did not significantly deviate from those of the green structures with various volume fractions of the space holder. Titanium scaffolds with a maximum specific surface area could be produced with an addition of 60–65 vol% carbamide particles to the matrix powder. The connectivity of pores inside the scaffold increased with rising volume fraction of the space holder. The shrinkage of the scaffolds prepared with > 50 vol% carbamide space holder, occurring during sintering, was caused by the reductions of macro-pore sizes and micro-pore sizes as well as the thickness of struts. In conclusion, the final porous structural characteristics of titanium scaffolds could be estimated from those of the green body. - Highlights: •Porous structures of green body and sintered titanium scaffolds was studied. •Porous structures of both samples were quantitatively characterized with micro-CT. •Porous structures of scaffolds could be controlled from the green body. •Shrinkage mechanisms of titanium scaffolds during sintering was established.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Interactive lung segmentation in abnormal human and animal chest CT scans

Purpose: Many medical image analysis systems require segmentation of the structures of interest as a first step. For scans with gross pathology, automatic segmentation methods may fail. The authors’ aim is to develop a versatile, fast, and reliable interactive system to segment anatomical structures. In this study, this system was used for segmenting lungs in challenging thoracic computed tomography (CT) scans. Methods: In volumetric thoracic CT scans, the chest is segmented and divided into 3D volumes of interest (VOIs), containing voxels with similar densities. These VOIs are automatically labeled as either lung tissue or nonlung tissue. The automatic labeling results can be corrected using an interactive or a supervised interactive approach. When using the supervised interactive system, the user is shown the classification results per slice, whereupon he/she can adjust incorrect labels. The system is retrained continuously, taking the corrections and approvals of the user into account. In this way, the system learns to make a better distinction between lung tissue and nonlung tissue. When using the interactive framework without supervised learning, the user corrects all incorrectly labeled VOIs manually. Both interactive segmentation tools were tested on 32 volumetric CT scans of pigs, mice and humans, containing pulmonary abnormalities. Results: On average, supervised interactive lung segmentation took under 9 min of user interaction. Algorithm computing time was 2 min on average, but can easily be reduced. On average, 2.0% of all VOIs in a scan had to be relabeled. Lung segmentation using the interactive segmentation method took on average 13 min and involved relabeling 3.0% of all VOIs on average. The resulting segmentations correspond well to manual delineations of eight axial slices per scan, with an average Dice similarity coefficient of 0.933. Conclusions: The authors have developed two fast and reliable methods for interactive lung segmentation in challenging chest CT images. Both systems do not require prior knowledge of the scans under consideration and work on a variety of scans.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Measurement of Photovoltaic Module Deformation Dynamics During Hail Impact Using Digital Image Correlation

Stereo high-speed video of photovoltaic modules undergoing laboratory hail tests was processed using digital image correlation to determine module surface deformation during and immediately following impact. The purpose of this work was to demonstrate a methodology for characterizing module impact response differences as a function of construction and incident hail parameters. Video capture and digital image analysis were able to capture out-of-plane module deformation to a resolution of ±0.1 mm at 11 kHz on an in-plane grid of 10 × 10 mm over the area of a 1 × 2 m commercial photovoltaic module. With lighting and optical adjustments, the technique was adaptable to arbitrary module designs, including size, backsheet color, and cell interconnection. Furthermore, impacts were observed to produce an initially localized dimple in the glass surface, with peak deflection proportional to the square root of incident energy. Subsequent deformation propagation and dissipation were also captured, along with behavior for instances when the module glass fractured. Natural frequencies of the module were identifiable by analyzing module oscillations postimpact. Limitations of the measurement technique were that the impacting ice ball obscured the data field immediately surrounding the point of contact, and both ice and glass fracture events occurred within 100 μs, which was not resolvable at the chosen frame rate. Increasing the frame rate and visualizing the back surface of the impact could be applied to avoid these issues. Applications for these data include validating computational models for hail impacts, identifying the natural frequencies of a module, and identifying damage initiation mechanisms.

14 SOLAR ENERGY↗
DOE OSTI2016

Disky elliptical galaxies and the allegedly over-massive black hole in the compact massive “es” galaxy NGC 1271

While spiral and lenticular galaxies have large-scale disks extending beyond their bulges, and most local early-type galaxies with 10{sup 10} < M {sub *}/M {sub ⊙} < 2 × 10{sup 11} contain a disk (e.g., ATLAS{sup 3D}), the early-type galaxies do possess a range of disk sizes. The edge-on, intermediate-scale disk in the “disky elliptical” galaxy NGC 1271 has led to some uncertainty regarding its spheroidal component. Walsh et al. reported a directly measured black hole mass of (3.0{sub −1.1}{sup +1.0})×10{sup 9} M{sub ⊙} for this galaxy, which they remarked was an order of magnitude greater than what they expected based on their derivation of the host spheroid’s luminosity. Our near-infrared image analysis supports a small embedded disk within a massive spheroidal component with M{sub sph,∗}=(0.9±0.2)×10{sup 11} M{sub ⊙} (using M{sub ∗}/L{sub H}=1.4{sub −0.11}{sup +0.13} from Walsh et al.). This places NGC 1271 just 1.6σ above the near-linear M {sub bh}–M {sub sph,*} relation for early-type galaxies. Therefore, past speculation that there may be a systematic difference in the black hole scaling relations between compact massive early-type galaxies with intermediate-scale disks, i.e., ES galaxies such as NGC 1271, and early-type galaxies with either no substantial disk (E) or a large-scale disk (S0) is not strongly supported by NGC 1271. We additionally (1) show how ES galaxies fit naturally in the (“bulge”-to-total)-(morphological-type) diagram, while noting a complication with recent revisions to the Hubble-Jeans tuning-fork diagram, (2) caution about claims of over-massive black holes in other ES galaxies if incorrectly modeled as S0 galaxies, and (3) reveal that the compact massive spheroid in NGC 1271 has properties similar to bright bulges in other galaxies, which have grown larger-scale disks.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2016

Quasar variability in the mid-infrared

The Decadal IRAC Boötes Survey is a mid-IR variability survey of the ∼9 sq. deg. of the NDWFS Boötes Field and extends the time baseline of its predecessor, the Spitzer Deep, Wide-Field Survey (SDWFS), from 4 to 10 years. The Spitzer Space Telescope visited the field five times between 2004 and 2014 at 3.6 and 4.5 μm. We provide the difference image analysis photometry for a half a million mostly extragalactic sources. In mid-IR color–color plane, sources with quasar colors constitute the largest variability class (75%), 16% of the variable objects have stellar colors and the remaining 9% have the colors of galaxies. Adding the fifth epoch doubles the number of variable active galactic nuclei (AGNs) for the same false positive rates as in SDWFS, or increases the number of sources by 20% while decreasing the false positive rates by factors of 2–3 for the same variability amplitude. We quantify the ensemble mid-IR variability of ∼1500 spectroscopically confirmed AGNs using single power-law structure functions (SFs), which we find to be steeper (index γ≈0.45) than in the optical (γ≈0.3), leading to much lower amplitudes at short time-lags. This provides evidence for large emission regions, smoothing out any fast UV/optical variations, as the origin of infrared quasar variability. The mid-IR AGN SF slope γ seems to be uncorrelated with both the luminosity and rest-frame wavelength, while the amplitude shows an anti-correlation with the luminosity and a correlation with the rest-frame wavelength.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2014

TH-C-18A-05: Characteristics and Accuracy of CT Radiation Profile Width Measurements Using Radiochromic Films

Purpose: To investigate the impact of several acquisition and image analysis factors on the accuracy of CT beam width measurement using Gafchromic XR-QA2 film and an off the shelf document scanner. Methods: The film was carefully placed at the iso-center and exposed at various x-ray beam energies (80–140 kVp), exposure levels (50–400 mAs), and nominal beam widths (1.25, 5, and 10 mm). Films were scanned on a RICOH MP3501 flat-bed document scanner using reflection mode and various spatial resolutions (100 to 600 dpi) and locations within the scanner bed. Radiation dose profiles were derived by converting the net reflection measurements to dose values (in mGy) through film calibration (which is also described here). The beam widths were characterized by the FWHM and FWTM of the dose profiles and the deviations from the hybrid reference standards were quantified. The impact of x-ray beam energy, exposure intensity, film calibration, and the uniformity and spatial resolution of the document scanner were investigated. Results: The uncertainties in both FWHM and FWTM caused by varying beam energy, exposure level, and scanner uniformity were all within approximately 5%. Increasing scanner spatial resolution increased the uncertainty in both FWHM and FWTM (R2 = 0.35–0.71), with the FWTM affected by more than five times than the FWHM (28% vs. 4.9%). When uncalibrated dose profiles were used, the FWHM and FWTM were over-estimated by as much as 11.6% and 7.6%, respectively. Narrower beam width was more sensitive to the film calibration than the wider one (R2 = 0.68 and 0.85 for the FWHM and FWTM, respectively). Conclusion: Measurement of CT beam width using Gafchromic XR-QA2 films is robust against x-ray energy, exposure level, and scanner uniformity. It can provide adequate accuracy for all practical purposes with appropriate film calibration and scanner spatial resolution (100 dpi or less)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2017

Persistence of bubble outlets in soft, methane-generating sediments

Sediments submerged beneath many inland waterways and shallow oceans emit methane, a potent greenhouse gas, but the magnitude of the methane flux to the atmosphere remains poorly constrained. In many settings, the majority of methane is released through bubbling, and the spatiotemporal heterogeneity of this ebullition both presents challenges for measurement and impacts bubble dissolution and atmospheric emissions. In this paper, we present laboratory-scale experiments of methane ebullition in a controlled incubation of reconstituted sediments from a eutrophic lake. Image analysis of a 0.14 m 2 sediment surface area allowed identification of individual bubble outlets and resolved their location to ~1 cm. While ebullition events were typically concentrated in bursts lasting ~2 min, some major outlets showed persistent activity over the scale of days and even months. This persistence was surprising given the previously observed ephemerality of spatial structure at the field scale. This persistence suggests that, at the centimeter scale, conduits are reopened as a result of a drop in tensile strength due to deformation of sediments by the rising bubbles. Finally, the mechanistic insight from this work sheds light on the spatiotemporal distribution of methane venting from organic-rich sediments and has important implications for bubble survival in the water column and associated biogeochemical pathways of methane.

58 GEOSCIENCES↗
DOE OSTI2013

IMPACT OF PARTICLE AGGLOMERATION ON ACCUMULATION RATES IN THE GLASS DISCHARGE RISER OF HLW MELTER

The major factor limiting waste loading in continuous high-level radioactive waste (HLW) melters is an accumulation of particles in the glass discharge riser during a frequent and periodic idling of more than 20 days. An excessive accumulation can produce robust layers a few centimeters thick, which may clog the riser, preventing molten glass from being poured into canisters. Since the accumulation rate is driven by the size of particles we investigated with X-ray microtomography, scanning electron microscopy, and image analysis the impact of spinel forming components, noble metals, and alumina on the size, concentration, and spatial distribution of particles, and on the accumulation rate. Increased concentrations of Fe and Ni in the baseline glass resulted in the formation of large agglomerates that grew over the time to an average size of ~185±155 µm, and produced >3 mm thick layer after 120 h at 850 °C. The noble metals decreased the particle size, and therefore significantly slowed down the accumulation rate. Addition of alumina resulted in the formation of a network of spinel dendrites which prevented accumulation of particles into compact layers.

Accumulation↗
DOE OSTI2014

The effects of glass doping, temperature and time on the morphology, composition, and iron redox of spinel crystals

Precipitation of large crystals/agglomerates of spinel and their accumulation in the pour spout riser of a Joule-heated ceramic melter during idling can plug the melter and prevent pouring of molten glass into canisters. Thus, there is a need to understand the effects of spinel-forming components, temperature, and time on the growth of crystals in connection with an accumulation rate. In our study, crystals of spinel [Fe, Ni, Mn, Zn, Sn][Fe, Cr]₂O₄ were precipitated from simulated high-level waste borosilicate glasses containing different concentrations of Ni, Fe, and Cr by heat treating at 850 and 900°C for different times. These crystals were extracted from the glasses and analyzed with scanning electron microscopy and image analysis for size and shape, with inductively coupled plasma-atomic emission spectroscopy and atom probe tomography for concentration of spinel-forming components, and with wet colorimetry and Mössbauer spectroscopy for Fe²⁺/Fe total ratio. High concentrations of Ni, Fe, and Cr in glasses resulted in the precipitation of crystals larger than 100 µm in just two days. Crystals were a solid solution of NiFe₂O₄, NiCr₂O₄, and -Fe₂O₃ (identified only in the high-Ni-Fe glass) and also contained small concentrations of less than 1 at% of Li, Mg, Mn, and Al.

chemical analysis↗
DOE OSTI2024

High–Performance NiCo 2 O 4 /Graphene Quantum Dots for Asymmetric and Symmetric Supercapacitors with Enhanced Energy Efficiency

For the sustainable growth of future generations, energy storage technologies like supercapacitors and batteries are becoming more and more common. However, reliable and high-performance materials’ design and development is the key for the widespread adoption of batteries and supercapacitors. Quantum dots with fascinating and unusual properties are expected to revolutionize future technologies. However, while the recent discovery of quantum dots honored with a Nobel prize in Chemistry, their benefits for the tenacious problem of energy are not realized yet. In this context, herein, chemical-composition tuning enabled exceptional performance of NiCo 2 O 4 (NCO)/graphene quantum dots (GQDs) is reported, which outperform the existing similar materials, in supercapacitors. A comprehensive study is performed on the synthesis, characterization, and electrochemical performance evaluation of highly functional NCO/GQDs in supercapacitors delivering enhanced energy efficiency. The high-performance, functional NCO/GQDs electrode materials are synthesized by the incorporation of GQDs into NCO. The effect of variable amount of GQDs on the energy performance characteristics of NCO/GQDs in supercapacitors is studied systematically. In-depth structural and chemical bonding analyses using X-ray diffraction (XRD) and Raman spectroscopic studies indicate that all the NCO/GQDs composites crystallize in the spinel cubic phase of NiCo 2 O 4 while graphene integration evident in all the NCO/GQDs. The scanning electron microscopy imaging analysis reveals homogeneously distributed spherical particles with a size distribution of 5–9 nm validating the formation of QDs. The high-resolution transmission electron microscopy analyses reveal that the NCOQDs are anchored on graphene sheets, which provide a high surface area of 42.27 m 2 g –1 and high mesoporosity for the composition of NCO/GQDs-10%. In addition to establishing reliable electrical connection to graphene sheets, the NCOQDs provide reliable 3D-conductive channels for rapid transport throughout the electrode as well as synergistic effects. Chemical-composition tuning, and optimization yields NCO/GQDs-10% to deliver the best specific capacitance of 3940 Fg –1 at 0.5 Ag –1 , where the electrodes retain ≈98% capacitance after 5000 cycles. The NCO/GQD-10%//AC asymmetric supercapacitor device demonstrates outstanding energy density and power density values of 118.04 Wh kg –1 and 798.76 W kg –1 , respectively. The NCO/GQDs-10%//NCO/GQDs-10% symmetric supercapacitor device delivers excellent energy and power density of 24.30 Wh kg –1 and 500 W kg –1 , respectively. These results demonstrate and conclude that NCO/GQDs are exceptional and prospective candidates for developing next-generation high-performance and sustainable energy storage devices.

25 ENERGY STORAGE↗
DOE OSTI2023

Solid‐State Reaction Heterogeneity During Calcination of Lithium‐Ion Battery Cathode

Abstract During solid‐state calcination, with increasing temperature, materials undergo complex phase transitions with heterogeneous solid‐state reactions and mass transport. Precise control of the calcination chemistry is therefore crucial for synthesizing state‐of‐the‐art Ni‐rich layered oxides (LiNi 1‐x‐y Co x Mn y O 2 , NRNCM) as cathode materials for lithium‐ion batteries. Although the battery performance depends on the chemical heterogeneity during NRNCM calcination, it has not yet been elucidated. Herein, through synchrotron‐based X‐ray, mass spectrometry microscopy, and structural analyses, it is revealed that the temperature‐dependent reaction kinetics, the diffusivity of solid‐state lithium sources, and the ambient oxygen control the local chemical compositions of the reaction intermediates within a calcined particle. Additionally, it is found that the variations in the reducing power of the transition metals (i.e., Ni, Co, and Mn) determine the local structures at the nanoscale. The investigation of the reaction mechanism via imaging analysis provides valuable information for tuning the calcination chemistry and developing high‐energy/power density lithium‐ion batteries.

Chemistry↗
DOE OSTI2019

Fragmentation and film growth in supersonic nanoaggregate aerosol deposition

Aerosol deposition with gas phase-synthesized chain-like nanoaggregates can yield dense coatings from the impaction of particles on a substrate; however, dense coating formation is not well understood. Here, we study coating consolidation at the single nanoaggregate level. Flame spray pyrolysis-made tin oxide nanoaggregates are mobility (size) filtered, accelerated through a de Laval nozzle, and impacted on alumina substrates. TEM images obtained from low velocity collection and supersonic deposition are compared via quantitative image analysis, which reveals that upon supersonic impact nanoaggregates fragment into smaller aggregates. Furthermore, this suggests that fragmentation is a key step in producing coatings denser than the depositing nanoaggregates themselves. We supplement experiments with detailed particle trajectory calculations, which show that the impact energies per atom during nanoaggregate deposition are below 0.2 eV/molecule. These results suggest that fragmentation can only occur at locations where nanoaggregates bonded by van der Waals and capillary interactions.

36 MATERIALS SCIENCE↗
DOE OSTI2016

High-Throughput Screening of Catalytic H 2 Production

Hydrogenases, ferredoxins, and ferredoxin-NADP + reductases (FNR) are redox proteins that mediate electron metabolism in vivo, and are also potential components for biological H 2 production technologies. A high-throughput H 2 production assay device (H 2 PAD) is presented that enables simultaneous evaluation of 96 individual H 2 production reactions to identify components that improve performance. Using a CCD camera and image analysis software, H 2 PAD senses the chemo-optical response of Pd/WO 3 thin films to the H 2 produced. H 2 PAD-enabled discovery of hydrogenase and FNR mutants that enhance biological H 2 production is reported. From a library of 10 080 randomly mutated Clostridium pasteurianum [FeFe] hydrogenases, we found a mutant with nearly 3-fold higher H 2 production specific activity. From a library of 400 semi-randomly mutated Oryza sativa FNR, the top hit enabled a 60 % increase in NADPH-driven H 2 production rates. H 2 PAD can also facilitate elucidation of fundamental biochemical mechanisms within these systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Synthesis and characterization of porous polydimethylsiloxane structures with adjustable porosity and pore morphology using emulsion templating technique

Abstract Porous polydimethylsiloxane (PDMS) framework with adjustable pore structures has been fabricated by polymerization of the continuous phase in the emulsion templates. Different types of surfactants, including nonionic (Triton X‐100), cationic (Benzalkonium chloride), anionic (sodium dodecyl sulfate), and silicone‐based block copolymer were used to stabilize the water‐in‐oil emulsion system. Deionized water with a wide range of internal phases varying from 10% to 60% by weight was employed to make the low internal phase emulsion and medium internal phase emulsion. The effect of surfactant type, surfactant concentration, and the internal phase volume on the stability of the emulsion, pore morphology, and pore size distribution was explored. The stability of the emulsion was investigated by comparing the pore morphology of the cured sample at different set times, such as 0, 6, and 72 h. Scanning electron microscopy was employed for the characterization of the porous structures. The image analysis was conducted, and the pore size distribution, porosity, and open‐cell ratio of each sample were calculated. Interconnected pores have been seen in the porous PDMS made from emulsions with an internal phase larger than 30%. The results demonstrated that the frequency of open‐cell pores and the pore size is dependent on the surfactant types.

Abshirini, Mohammad↗
DOE OSTI2020

Uncertainty-based weighted least squares density integration for background-oriented schlieren

We propose an improved density integration methodology for Background-Oriented Schlieren (BOS) measurements that overcomes the noise sensitivity of the commonly used Poisson solver. Here, the method employs a weighted least-squares (WLS) optimization of the 2D integration of the density gradient field by solving an over-determined system of equations. Weights are assigned to the grid points based on density gradient uncertainties to ensure that a less reliable measurement point has less effect on the integration procedure. Synthetic image analysis with a Gaussian density field shows that WLS constrains the propagation of random error and reduces it by 80% in comparison to Poisson for the highest noise level. Using WLS with experimental BOS measurements of flow induced by a spark plasma discharge shows a 30% reduction in density uncertainty in comparison to Poisson, thereby increasing the overall precision of the BOS density measurements.

42 ENGINEERING↗
DOE OSTI2019

Investigation of Stress Field and Fracture Development During Shale Maturation Using Analog Rock Systems

The emergence of hydrocarbons within shale as a major recoverable resource has sparked interest in fluid transport through these tight mudstones. Recent studies suggest the importance to recovery of microfracture networks that connect localized zones with large organic content to the inorganic matrix. This paper presents a joint modeling and experimental study to examine the onset, formation, and evolution of microfracture networks as shale matures. Both the stress field and fractures are simulated and imaged. A novel laboratory-scale, phase-field fracture propagation model was developed to characterize the material failure mechanisms that play a significant role during the shale maturation process. The numerical model developed consists of coupled solid deformation, pore pressure, and fracture propagation mechanisms. Benchmark tests were conducted to validate model accuracy. Laboratory-grade gelatins with varying Young’s modulus were used as scaled-rock analogs in two dimensional Hele-Shaw cell apparatus. Yeast within the gelatin generates gas in a fashion analogous to hydrocarbon formation as shale matures. These setups allow study and visualization of host rock elastic-brittle fracture and fracture network propagation mechanisms. The experimental setup was fitted to utilize photoelasticity principles coupled with birefringence properties of gelatin to explore visually the stress field of the gelatin as the fracture network developed. Stress optics image analysis and Linear Elastic Fracture Mechanics (LEFM) principles for crack propagation were used to monitor fracture growth for each gelatin type. Observed and simulated responses suggest gas diffusion within and deformation of the gelatin matrix as predominant mechanisms for energy dissipation depending on gelatin strength. LEFM, an experimental estimation of principal stress development with fracture growth, at different stages was determined for each gelatin rheology. Here, the interplay of gas diffusion and material deformation determines the resulting frequency and pattern of fractures. Results correlate with Young’s modulus. Experimental and computed stress fields reveal that fractures resulting from internal gas generation are similar to, but not identical to, type 1 opening mode.

58 GEOSCIENCES↗
DOE OSTI2025

Evaluation of desiccation cracking characteristics of inorganic micro-fiber-reinforced engineered barrier material (IMEBM) for geological repository

Abstract Buffer material is crucial for the engineering barrier system to dispose of high-level radioactive waste in a geological repository. A reliable buffer material should be able to maintain good sealing characteristics and minimize desiccation cracking. In this study, the effectiveness of inorganic fiber-reinforced engineering barrier material in reducing desiccation cracks in bentonite was evaluated via desiccation tests, image analysis, and air permeability tests. The effects of fiber type (E-glass fiber and basalt fiber) and fiber content (0.0%, 0.5%, 1.0%, 1.5%, 3.0%, and 5.0% of dry weight of the bentonite) on the development of desiccation cracks in the fiber–bentonite mixtures with the same given initial moisture content were evaluated. The results indicated that the addition of fibers could significantly reduce the crack size and area in bentonite during the drying. Basalt fibers showed a slightly better reinforcement effect than E-glass fibers when the fiber content was lower than 3.0%. The addition of fibers prevented the development of penetrating cracks and significantly reduced the permeability of the bentonite after drying. The permeabilities of basalt fiber- and E-glass fiber-reinforced bentonite composites with 3% reinforcement were 5.81 × 10 –11 m 2 and 7.24 × 10 –11 m 2 , respectively, which were 64 and 51 times smaller than that of pure bentonite. X-ray–CT observation of the internal structure of the samples after drying showed that the addition of fibers significantly changed the crack morphology and potentially increased the tortuosity.

Feng, Yuan↗