Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

AlSb thin films as negative electrodes for Li-ion and Na-ion batteries

The electrochemical reactions between Li and Na with amorphous/nanocrystalline AlSb thin films prepared by magnetron sputtering are reported for the first time. The films are composed of AlSb and Sb nanoparticles embedded into an amorphous matrix with an overall Sb/Al ratio of 1.13. The reaction with Li proceeds with an average reaction potential of 0.65 V, a reversible capacity of 750 mAh g-1, and very fast reaction kinetics. For instance, a storage capacity close to 500 mAh g-1, corresponding to 70% of the maximum capacity, is achieved at 125 C-rate. In addition, there is only a small increase in overpotentials with increasing current: ~0.15 V at 12 C and ~0.7 V at 125 C. In contrast, the reaction with Na results in average reaction potential of 0.5 V and a storage capacity of 500 mAh g-1 obtained at low currents. The capacity retention and reaction kinetics are presently not satisfactory with pronounced capacity losses upon cycling and large overpotentials with increasing current. The capacity retention can be improved by using fluoroethylene carbonate additive in the Na-ion electrolyte, which highlights that the Solid Electrolyte Interphase plays an important role for the electrode cycling stability. The reaction kinetics is relatively poor and an increase in overpotentials of about 0.9 V at 2 C is observed (retained capacity of about 350 mAh g-1 or 66% of the maximum). The study of the reaction mechanism on thick films (3-5 m) by X-ray diffraction reveals that the electrode material remains amorphous at all potentials. The presence of broad humps, located at the positions expected for Li-Al and Li-Sb line compounds, suggests that during the reaction with Li the atomic short range ordering is similar to the expected phases.

Baggetto, Loic↗

Growth of single crystalline TaON on yttria-stabilized zirconia (YSZ)

Owing to its high stability in aqueous solution and high quantum efficiency, tantalum based oxyntride (TaON) has attracted increasing attentions for application as visible light photocatalyst. However, despite the recent progress in photocatalytic studies, its bulk charge transport mechanisms are yet to be discovered because of the lack of single crystal sample. In this paper, high quality single crystalline TaON(100) thin film was prepared on cubic YSZ(100) surface by reactive RF magnetron sputtering to avail the understandings of charge transport mechanism so as to improve the device efficiency. The stoichiometry, crystal phase and structure were examined in situ by x-ray photoelectron spectroscopy (XPS) and ex situ by x-ray diffraction (XRD) and transmission electron microscopy (TEM). The TaON film crystallizes in monoclinic β-phase with its [010]/[001] directions aligned to those of the substrate. The small band gap of 2.5 eV as well as the high structure perfection suggests better performance for visible light water splitting. The method can be used to prepare other surface orientations to elucidate fundamental surface structure dependent photoactivities. - Graphical abstract: Structure of single crystalline β-TaON and its diffraction pole figure. Highlights: • High quality single crystal TaON(100) thin film were grown on YSZ(100) surface. • β-phase monoclinic TaON film is formed. • Its [010]/[001] directions are aligned to those of the substrate. • The small band gap and structure perfection suggest visible light photo-activity.

36 MATERIALS SCIENCE↗

Electron doping of NdNiO 3 thin films using dual chamber CaH 2 annealing

Hydrogen donor doping has been exploited as a strategy to manipulate the electronic structure and electrical properties of functional oxide systems. Especially, the development of synthetic methods to achieve electron doping of perovskite rare-earth nickelate thin films utilizing interstitial hydrogen is highly desirable considering the rich electronic phase diagram hosting several functional properties. Here, in this work, we present the hydrogenation of NdNiO 3 (NNO) thin films using CaH 2 annealing and the resulting giant modulation of electrical resistivity in hydrogenated NNO (H–NNO) thin films. Magnetron sputtering was employed to deposit epitaxial ~60 nm-thin NNO films on single crystal LaAlO 3 (LAO) substrates. The formation of the pristine perovskite NNO phase was realized after annealing the films at 500 °C for 24 h. CaH 2 annealing of NNO thin films for time durations ranging from 1 to 6 h was performed in a vacuumed ampule with two interconnected chambers at 280 °C. The two-chamber design enables a simple and clean approach for hydrogen doping without physical contact between the powder and sample of interest. X-ray diffraction and Raman spectroscopy revealed the formation of NNO in pristine samples, and the subsequent hydrogen incorporation upon CaH 2 annealing without forming any impurity phases. The conversion of the oxidation state of Ni towards +2 upon CaH 2 annealing was probed using X-ray photoelectron spectroscopy and X-ray absorption spectroscopy. Consequently, a substantial increase in the room-temperature resistivity was observed upon CaH 2 annealing indicating the formation of a strongly correlated electronic configuration of Ni in H–NNO due to electron doping. Overall, the findings of this study highlight the versatility of CaH 2 annealing as an electron doping method to tune the electrical properties of correlated oxides at low temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Corrosion behavior of Ti-Al-N/Ti-Al duplex coating on AZ31 magnesium alloy in NaCl aqueous solution

In this study, Ti-Al-N/Ti-Al duplex coating was deposited on AZ31 magnesium alloy by magnetron sputtering with a Ti/Al composite target. Scanning electron microscopy and Auger electron spectroscopy were applied to investigate the morphology and elemental concentration of the obtained coating, respectively. The top layer was Ti-Al-N film with a Ti:Al:O:N ratio of 0.32:0.84:0.08:1, and the bottom layer was Ti-Al film with a Ti:O:Al ratio of 1.94:0.12:1. Each layer of this coating presented a developed columnar structure. The polarization test and immersion test were used to investigate corrosion behavior of the coated sample in 3.5 wt.% NaCl aqueous solution. The results showed that this duplex coating could protect the substrate effectively in NaCl aqueous solution. Nevertheless, several through-thickness micropores in the coating finally induced the failure of the coated AZ31 in the immersion test.

36 MATERIALS SCIENCE↗

Microstructural characterisation of nanocomposite nc-MeC/a-C coatings on oxygen hardened Ti-6Al-4V alloy

Nanocomposite coatings are novel, important systems composed of two or more nanocrystalline, or nanocrystalline and amorphous, phases. Such coatings offer a possibility of tailoring the coating microstructure and achieving new improved properties of coated materials. In this work a duplex surface treatment, consisting of an oxygen diffusion treatment and deposition of low friction nanocomposite nc-MeC/a-C (Me = transition metal, Ti, W or Cr) coatings, was applied for improvement of the Ti-6Al-4V alloy properties. The coatings composed of nanocrystallites of transition metal carbides (TiC or Cr{sub x}C{sub y} or WC) embedded in hydrogen-free amorphous carbon (a-C) matrix were deposited onto the surface of an oxygen hardened Ti-6Al-4 V alloy substrate by means of a simple DC magnetron sputtering. A nano/microstructure of the substrate material and coatings has been examined by scanning- and transmission electron microscopy complemented with the results of X-ray diffraction analyses. It was found that the nanocomposite coatings are composed of different carbide nanocrystals (with sizes of a few nanometres) embedded in an amorphous carbon matrix. The results of qualitative and quantitative analyses of the nanocrystalline phase in the coatings with use of high-resolution transmission electron microscopy combined with image analysis are given in the paper. An effect of the nano/microstructure parameters of the coated alloy onto its micro-mechanical (nanohardness and Young's modulus) and tribological properties (wear resistance and friction coefficient) is discussed in the paper.

36 MATERIALS SCIENCE↗

Thin film ceria–bismuth bilayer electrolytes for intermediate temperature solid oxide fuel cells with La0.85Sr0.15MnO3-δ–Y0.25Bi0.75O1.5 cathodes

Thin film electrolytes of bilayer bismuth oxide/ceria are developed for intermediate temperature solid oxide fuel cells. Y0.25Bi0.75O1.5 is deposited via Direct Current magnetron sputtering technique on an Sm0.2Ce0.8O1.90 electrolyte film which is prepared by a dry-pressing process on an NiO–Sm0.2Ce0.8O1.90 substrate. La0.85Sr0.15MnO3-δ–Y0.25Bi0.75O1.5 composite is applied onto the Y0.25Bi0.75O1.5 film as the cathode to form a single cell. Cells with 6-μm-thick Y0.25Bi0.75O1.5 and 26-μm-thick Sm0.2Ce0.8O1.90 bilayer electrolytes exhibit improved open circuit voltages and power density compared with those obtained with only Sm0.2Ce0.8O1.90 electrolytes. The open circuit voltages are comparable and power densities are higher than those previously reported for solid oxide fuel cells with thick bilayer electrolytes using noble metals such as Pt as the electrodes. Impedance spectra show that the change of electrolyte resistance is negligible while the cathodic interfacial polarization resistance decreased significantly when the Y0.25Bi0.75O1.5 layer is added to form the Sm0.2Ce0.8O1.90/Y0.25Bi0.75O1.5 bilayer electrolytes.

36 MATERIALS SCIENCE↗

The effect of annealing temperature on the electrical characterization of Co/n type GaP Schottky diode

The Co/n-GaP nano-Schottky diodes have been fabricated to investigate effect of annealing temperature on the characteristics of the device. DC Magnetron sputtering technique has been used for Co metallic contact. The samples have been annealed for three minutes at 400 °C and 600 °C. XRD analyzes of the devices subjected to thermal annealing process have been investigated. Surface images have been taken with atomic force microscopy (AFM) in order to examine the morphology of the surface of the metal layer before and after the annealing the sample. The current–voltage (I–V) measurements taken at room temperature have shown that the ideality factor and series resistance decrease with the increasing annealing temperature. The ideality factor was found to be 1.02 for sample annealed at 400 °C. Before and after annealing, depending on the temperature measurement, the capacitance–frequency (C–f), and conductance–frequency (G–f) have been measured, and graphs have been plotted.

36 MATERIALS SCIENCE↗

High (1 1 1) orientation poly-Ge film fabricated by Al induced crystallization without the introduction of AlO{sub x} interlayer

High (1 1 1) orientation poly-Ge film was fabricated by Al induced crystallization (AIC), where Al and amorphous Ge (a-Ge) layers were continuously deposited by magnetron sputtering, avoiding the deliberate introduction of an AlO{sub x} interlayer. To improve the quality of poly-Ge film, the ratio of thicknesses of Al and a-Ge was adjusted. Electron backscattered diffraction (EBSD) results revealed that the (1 1 1) fraction of poly-Ge film reached 97% and the average crystal grain size surpassed 100 μm.

36 MATERIALS SCIENCE↗

Fabrication and characterization of metal–semiconductor–metal ultraviolet photodetector based on rutile TiO{sub 2} nanorod

The fabrication and characterization of a metal–semiconductor–metal ultraviolet photodetector are studied. The photodetector is based on TiO{sub 2} nanorods (NRs) grown on p-type (1 1 1)-oriented silicon substrate seeded with a TiO{sub 2} layer is synthesized by radio frequency reactive magnetron sputtering. A chemical bath deposition is used to grow TiO{sub 2} NRs on Si substrate. The structural and optical properties of the obtained sample are analyzed by using X-ray diffraction and field emission-scanning electron microscopy. Results show a tetragonal rutile structure of the synthesized TiO{sub 2} NRs. Optical properties are further examined using photoluminescence spectroscopy. A sharp and high-intensity UV peak at 367 nm is observed in comparison with visible defect peaks centered at 432 and 718 nm. Upon exposure to 365 nm light (2.3 mW/cm) at 5 V bias, the device displays 76.06 × 10{sup 2} sensitivity, internal photodetector gain of 77.06, photocurrent of the device is 2.62 × 10{sup −5} A and photoresponse peak of 69.7 mA/W. The response and recovery times are calculated as 18.5 and 19.1 ms upon illumination to a pulse UV light (365 nm, 2.3 mW/cm{sup 2}) at 5 V applied bias. These results demonstrate that the fabricated high-quality photodiode is a promising candidate as a low-cost UV photodetector for commercially-integrated photoelectronic applications.

36 MATERIALS SCIENCE↗

Wettability, structural and optical properties investigation of TiO{sub 2} nanotubular arrays

Graphical abstract: FESEM images of the TiO 2 nanotube layers formed at 0.5 wt% NH4F/ glycerol. - Highlights: • Structural property investigation of TiO{sub 2} nanotube. • Evaluation of wettability of TiO{sub 2} nanotube. • Study on optical properties of TiO{sub 2} nanotube. • The effect of anatase phase on optical and wettability properties of TiO{sub 2.} - Abstract: In this study, the effect of microstructural evolution of TiO{sub 2} nanotubular arrays on wettability and optical properties was investigated. Pure titanium was deposited on silica glass by PVD magnetron sputtering technique. The Ti coated substrates were anodized in an electrolyte containing NH{sub 4}F/glycerol. The structures of the ordered anodic TiO{sub 2} nanotubes (ATNs) as long as 175 nm were studied using field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD). The result shows a sharp peak in the optical absorbance spectra around the band gap energy, 3.49–3.42 eV for annealed and non-annealed respectively. The thermal process induced growth of the grain size, which influence on the density of particles and the index of refraction. Furthermore, the wettability tests' result displays that the contact angle of intact substrate (θ = 74.7°) was decreased to 31.4° and 17.4° after anodization for amorphous and heat treated (450 °C) ANTs coated substrate, respectively.

36 MATERIALS SCIENCE↗

Ti{sub 2}AlN thin films synthesized by annealing of (Ti+Al)/AlN multilayers

Highlights: • Epitaxial thin films of the MAX phase Ti{sub 2}AlN are obtained by thermal annealing. • A new metastable (Ti,Al,N) solid solution with the structure of α-T is evidenced. • The formation of the MAX phase occurs at low temperature (600 °C). - Abstract: Single-phase Ti{sub 2}AlN thin films were obtained by annealing in vacuum of (Ti + Al)/AlN multilayers deposited at room temperature by magnetron sputtering onto single-crystalline (0001) 4H-SiC and (0001) Al{sub 2}O{sub 3} substrates. In-situ X-ray diffraction experiments combined with ex-situ cross-sectional transmission electron microscopy observations reveal that interdiffusion processes occur in the multilayer at a temperature of ∼400 °C leading to the formation of a (Ti, Al, N) solid solution, having the hexagonal structure of α-Ti, whereas the formation of Ti{sub 2}AlN occurs at 550–600 °C. Highly oriented (0002) Ti{sub 2}AlN thin films can be obtained after an annealing at 750 °C.

36 MATERIALS SCIENCE↗

Investigation of CrMnV and CrMnTiV multi principal element alloys thin films for use as exit windows of electron beam accelerators

Here, this study explores CrMnV and CrMnTiV multi principal element alloy (MPEA) films as candidates for electron beam exit windows in industrial, high-power accelerators. Films were deposited via magnetron sputtering on various substrates and exposed to 66 kGy of 10 MeV e-beam irradiation. Structural and mechanical properties were analyzed using FESEM, XRD, and nanoindentation. CrMnTiV films exhibited superior grain uniformity and hardness, regardless of the substrate type. Compared to bulk materials, both MPEA films demonstrated higher hardness and excellent radiation resistance. These results highlight the potential of MPEA films as durable, radiation-tolerant materials for high-performance accelerator exit window applications.

Electron Beam Irradiation↗

The microstructure and He + ion irradiation behavior of novel low-activation W-Ta-Cr-V refractory high entropy alloy for nuclear applications

Microstructure and nanohardness of a nearly equimolar W-Ta-Cr-V high entropy alloy (HEA), as well as its irradiation response under He + irradiation, were investigated. The single-phase body-centered cubic nanostructured alloy with a 1 µm thick layer was fabricated on a silicon substrate using a magnetron sputtering method. The HEA film has a complex microstructure consisting of micrometric domains that exhibit internal nanostructure controlled by their crystal orientation. The measured nanohardness of the W-Ta-Cr-V alloy is 13 ± 2 GPa, which significantly exceeds the hardness of nanocrystalline tungsten as a result of the high solid-solution strengthening effect. In order to evaluate the irradiation resistance of the HEA film, the material was irradiated with 200 keV He + ions at room temperature, with two different ion fluences: 1 × 10 16 and 5 × 10 16 ions/cm 2 . Using transmission electron microscopy, a high density of extremely fine He bubbles is observed that were uniformly distributed in the matrix. The increase of He + ion fluence increased the density of bubbles, whereas their size remained at a similar level, which indicates that the damage proceeds by the nucleation of additional He bubbles, not by their growth.

36 MATERIALS SCIENCE↗

Durability enhancement of all-solid-state electrochromic devices by adjusting the charge density ratio between electrochromic and counter electrode layers

Here, owing to an increase in global warming, smart-window devices based on charge-balanced electrochromic devices (ECDs), which exhibit high potential to increase the thermal efficiency of buildings, have gained prominence. However, studies on the fabrication and cycling stability of charge-balanced ECDs are scarce. In this study, WO 3 and NiO x films were deposited on indium-tin-oxide (ITO)-coated glass substrates by reactive direct-current magnetron sputtering, and the deposition time was varied to control the thickness and charge density of the thin films. Subsequently, the NiO x /ITO/glass and WO 3 /ITO/glass substrates were laminated with a Li-based polymeric electrolyte to fabricate all-solid-state ECDs comprising electrochromic (EC) and counter-electrode (CE) layers in charge-density ratios of 12.6, 6.4, 2.3, and 1.1. Changes in the electrochromic properties, device-layer microstructure, crystal structure, and elemental composition of the as-constructed ECDs before and after degradation were investigated to understand the influence of the charge-density ratio of the EC and CE layers on the long-term durability of ECDs. Increasing the charge-density ratio decreased the cycling stability of the device owing to changes in the microstructure and crystal structure of the NiO x layer in the microstructural deep-trap sites. Among all the ECDs, those comprising EC and CE layers with similar charge densities showed the most stable optical modulation and highest long-term durability. Finally, based on the aforementioned results, a degradation mechanism for charge-imbalanced all-solid-state ECDs was proposed. This study is expected to open new frontiers in designing optimal-performance electrochemical devices with a wide variety of potential applications.

14 SOLAR ENERGY↗

Effect of the addition of Si into V 2 O 5 coatings: Structure and tribo-mechanical properties

Vanadium oxide (V2O5) is one of the lubricious oxides with the potential to be used as a solid lubricant at elevated temperatures. However, the material itself is not hard wear-resistant, so most of the research has focused on adding V into hard nitride coatings that could lead to the formation of a self-lubricating V(2)O(5)layer when heated. The other possible solution, which has been less studied, is to look for mechanisms to enhance the hardness of the oxide coating. In this research, we investigate the effect of the addition of Si into the V2O5 coatings, aiming to find conditions that lead to enhance hardness and/or reduced wear while keeping the high temperature lubricity of the V2O5 structure. For this, Si modified V2O5 coatings were deposited using a dual magnetron sputtering system. The results showed that small additions of Si (< 2.0 at%) improved the hardness of the V2O5 coatings up to 5 times while keeping the same temperature dependence of the coefficient of friction than V2O5. Dry sliding experiments using the pin-on-disc configuration against silicon nitride balls were performed at 25, 300 and 600 degrees C. Wear factors in the 10(-7) mm(3)/Nm range were obtained, indicating a good wear resistance. Further addition of Si into the V2O5 structure led to a loss of the crystalline ordering and a significant reduction in the hardness.

Hall-Petch↗

Correlating high temperature mechanical and tribological properties of CrAlN and CrAlSiN hard coatings

CrAlN and CrAlSiN hard coatings deposited by magnetron sputtering were analyzed for their high temperature mechanical and tribological properties. High temperature nanoindentation measurements on both coatings were performed from room temperature up to 700 °C in steps of 100 °C where a reduction in hardness H and elastic modulus E* from their initial values was noticed. In addition, high temperature tribological tests were conducted in inert atmosphere in the same temperature range to obtain information about the coefficient of friction and the wear coefficient. In order to link the tribological behavior to the obtained mechanical properties, the H/E* ratio was calculated and compared to the high temperature wear from the current and other studies with similar coatings. Finally, the evolution of the mechanical and tribological properties at high temperature is discussed based on the current knowledge available in literature.

Drnovšek, Aljaž↗

High temperature fracture toughness of single-layer CrAlN and CrAlSiN hard coatings

Hardness and toughness are among of the most important physical properties of hard coatings and it is important to analyze them at temperatures present during coating applications. CrAlN and CrAlSiN are hard coating materials frequently used in high temperature applications. Here, while both possess high oxidation resistance and thermal stability, they differ in their microstructure. In this work, the fracture toughness of magnetron-sputtered single-layer CrAlN and CrAlSiN hard coatings was determined up to 700 °C by in-situ scanning electron microscopy micro-cantilever deflection tests. The results show a decreasing trend of the fracture toughness with increasing temperature. While both coatings' fracture toughness trends are similar up to 400 °C, they diverge at higher temperatures. In general, the evolution of the fracture toughness with increasing temperature shows similarities to the observed changes in hardness in the same temperature range.

36 MATERIALS SCIENCE↗