Search NASA⌕ Search

SEARCH · Search NASA

Results for “Power Generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

10 MWE CDCL Large Pilot Plant – pre-FEED Study

Coal Direct Chemical Looping (CDCL) is an advanced oxy-combustion technology that has the potential to substantially reduce the energy penalty and the cost of electricity (COE) for coal-fired power generation with CO₂ capture. The Babcock & Wilcox Company (B&W) and The Ohio State University (OSU) have been collaborating on the development of an iron oxide oxygen-carrier based chemical looping technology for clean power generation with inherent carbon capture. In this process, coal is dried and pulverized prior to being transported into a moving-bed reducer. In the reducer, coal reacts with the oxygen-carrier particles, forming combustion byproducts, predominantly CO₂ and H₂O, while reducing the iron oxide oxidation state from Fe₂O₃ to a mixture of FeO and Fe. The reduced state particles are then transported to a combustor reactor and re-oxidized with air. Following the oxidation, the oxygen-carrier particles are regenerated, and a large amount of heat is released for steam production. The produced steam is sent to a turbine for electricity generation. Meanwhile, the CO₂–rich stream leaving the reducer is cooled, cleaned, and compressed for subsequent pipeline transportation and sequestration. By combining air separation and fuel conversion into a single system, the CDCL technology enables the intensification of oxy-combustion processes by eliminating the energy and cost intensive cryogenic air separation unit and thereby results in higher overall plant efficiencies and lower COE’s. The use of a moving-bed reducer results in high conversions of volatile hydrocarbons and high CO₂ purity, which reduces the cost of downstream CO₂ purification for sequestration or utilization. The Babcock & Wilcox Company in collaboration with The Ohio State University, Johnson & Matthey, The Electric Power Research Institute, and Dover Light & Power completed a Preliminary Front-End Engineering and Design (Pre-FEED) study of a 10 MWe coal-direct chemical looping (CDCL) pilot plant. The planned system is a modular 10 MWe CDCL large pilot facility consisting in 4 modules of 2.5 MWe each, working in parallel and to be hosted within the current structure at the City of Dover’s Municipal Power Plant. The CDCL system can achieve auto-thermal operation and includes a sub-critical steam cycle for power generation. The pilot system was designed to demonstrate full commercial operation at a reduced scale. The coal distribution per plan area is a representative slice of larger commercial arrangements. The system includes a CO₂ recycle system, but it does not include a compression system. The large pilot includes all the environmental control equipment and oxygen carrier and ash handling systems. As part of the project, the Team performed laboratory testing and carried out multiple pilot test campaigns to obtain design and performance information at the 250 kWth CDCL pilot facility at the Babcock & Wilcox Company’s Research Center. The Team demonstrated sustained operations at designed coal inputs, high coal conversion, high CO₂ purity, heat generation on the combustor, low carbon carryover between reactors and low particle attrition. Emissions generated in the reducer reactor were identified as SO₂ and NO x . The commercial manufacturing cost of oxygen carrier particle was evaluated by JM. A particle manufacturing report was generated and submitted to the DOE. Based on the results from the pilot tests and the pre-FEED design efforts, a techno-economic analysis was performed. The study shows that the CDCL process is a promising carbon-friendly technology capable of producing electricity with high efficiency. The estimated COE of the supercritical CDCL plant is $83.3 / MWh, which meets DOE’s target of less than 30% increase in COE when compared to a supercritical PC plant without CO₂ capture. This is the lowest among the existing carbon capture technologies (post-combustion and oxy-combustion) for fossil fuel power plant. CDCL is evaluated to be the most promising technology for carbon capture from the economic aspect.

01 COAL, LIGNITE, AND PEAT↗

iROSA Computational Model Development and Integration for the International Space Station

The power generation capability of the International Space Station (ISS) is being augmented with the installation of new solar arrays. The new solar arrays, named iROSA (ISS Roll Out Solar Array), are installed in front of original main truss solar arrays and integrate into the existing structure and electrical power system of the ISS. However, iROSA represents significant changes in technology for solar arrays compared to the original solar arrays on the ISS main truss. Knowing the power capabilities of the augmented solar arrays is critical for near-term and long-term mission planning and utilization. This new iROSA installation thus requires updates to be made to the prior-day methods of calculating power generation capability for the ISS. New types of solar cells and array designs, both electrically and structurally, present challenges for concurrent computational modeling of both the original solar arrays and the newer iROSA. This presentation will detail the development and integration of the computational models to calculate the power for the augmented arrays on ISS and the evaluation of the model to ensure that it functions with and without iROSA and returns accurate predictions of power generation in nominal and off-nominal conditions.

International Space Station↗

Chapter 6: Wind Energy: Effects on Bats

Utility-scale wind energy facilities require no fuel, consume no water, and produce no greenhouse gas emissions or other pollutants during energy production. Wind power currently supplies approximately 6.4% of the electricity consumed in the United States (U.S.), with continued growth expected in the coming years. Although further expansion of wind power is anticipated to provide environmental and economic benefits, there are increasing concerns about bat fatalities occurring at wind energy facilities across North America. Recent estimates place the number of bat fatalities in the several hundreds of thousands on an annual basis, and that number is projected to rise. As a result, population-level impacts of wind turbine-caused mortality are of increasing concern. For example, modeling efforts for a widespread species, the hoary bat (Lasiurus cinereus), indicate that the population could decline by 90% within 50 years, assuming no growth in installed wind power capacity and no significant implementation of conservation measures. Given increasing demand for wind energy and increasing evidence suggesting that bats are attracted to wind turbines, the need to develop cost-effective and practical impact minimization strategies is a high priority. Current strategies include siting restrictions and operational minimization, both of which limit wind power generation. Potential solutions that do not limit power generation include broadcasting ultrasound from wind turbines or using ultraviolet (UV) light to deter bats from approaching and entering the rotor-swept area where fatalities occur. Another possible solution is the development of turbine-surface materials that reduce the relative attractiveness of wind turbine towers to bats. In this chapter, we provide a succinct summary of known impacts of wind energy on bats and present current and future research priorities. We also describe the challenges and opportunities associated with developing and implementing effective solutions to minimize wind turbine-caused bat fatality.

17 WIND ENERGY↗

Carbon Molecular Sieve Membrane as a True One Box Unit for Large Scale Hydrogen Production

IGCC coal-fired power plants show promise for environmentally-benign power generation. In these plants coal is gasified to syngas then processed in a water gas-shift (WGS) reactor to maximize the hydrogen/CO 2 content. The gas stream can then be separated into a hydrogen rich stream for power generation and/or further purified for sale as a chemical and a CO 2 rich stream for the purpose of carbon capture and storage (CCS). Today, the separation is accomplished using conventional absorption/desorption processes with post CO 2 compression. However, significant process complexity and energy penalties accrue with this approach, accounting for ~20% of the capital cost and ~27% parasitic energy consumption. Ideally, a one-box process is preferred in which the syngas is fed directly to the WGS reactor without gas pre-treatment, converting the CO to hydrogen in the presence of H 2 S and other impurities and delivering a clean hydrogen product for power generation or other uses. The development of such a process is the primary goal of this project.

01 COAL, LIGNITE, AND PEAT↗

Solid State Energy Conversion Energy Alliance (SECA)

The overall objective is to develop a solid oxide fuel cell (SOFC) stack that can be economically produced in high volumes and mass customized for different applications in transportation, stationary power generation, and military market sectors. In Phase I, work will be conducted on system design and integration, stack development, and development of reformers for natural gas and gasoline. Specifically, Delphi-Battelle will fabricate and test a 5 kW stationary power generation system consisting of a SOFC stack, a steam reformer for natural gas, and balance-of-plant (BOP) components, having an expected efficiency of 35 percent (AC/LHV). In Phase II and Phase III, the emphasis will be to improve the SOFC stack, reduce start-up time, improve thermal cyclability, demonstrate operation on diesel fuel, and substantially reduce materials and manufacturing cost by integrating several functions into one component and thus reducing the number of components in the system. In Phase II, Delphi-Battelle will fabricate and demonstrate two SOFC systems: an improved stationary power generation system consisting of an improved SOFC stack with integrated reformation of natural gas, and the BOP components, with an expected efficiency of ≥40 percent (AC/LHV), and a mobile 5 kW system for heavy-duty trucks and military power applications consisting of an SOFC stack, reformer utilizing anode tailgate recycle for diesel fuel, and BOP components, with an expected efficiency of ≥30 percent (DC/LHV). Finally, in Phase III, Delphi-Battelle will fabricate and test a 5 kW Auxiliary Power Unit (APU) for mass-market automotive application consisting of an optimized SOFC stack, an optimized catalytic partial oxidation (CPO) reformer for gasoline, and BOP components, having an expected efficiency of 30 percent (DC/LHV) and a factory cost of ≤$400/kW.

30 DIRECT ENERGY CONVERSION↗

Solid State Energy Conversion Energy Alliance (SECA)

The overall objective is to develop a Solid Oxide Fuel Cell (SOFC) stack that can be economically produced in high volumes and mass customized for different applications in transportation, stationary power generation, and military market sectors. In Phase I, work will be conducted on system design and integration, stack development, and development of reformers for natural gas and gasoline. Specifically, Delphi-Battelle will fabricate and test a 5 kW stationary power generation system consisting of a SOFC stack, a steam reformer for natural gas, and balance-of-plant (BOP) components, having an expected efficiency of ≥ 35 percent (AC/LHV). In Phase II and Phase III, the emphasis will be to improve the SOFC stack, reduce start-up time, improve thermal cyclability, demonstrate operation on diesel fuel, and substantially reduce materials and manufacturing cost by integrating several functions into one component and thus reducing the number of components in the system. In Phase II, Delphi-Battelle will fabricate and demonstrate two SOFC systems: an improved stationary power generation system consisting of an improved SOFC stack with integrated reformation of natural gas, and the BOP components, with an expected efficiency of ≥ 40 percent (AC/LHV), and a mobile 5 kW system for heavy-duty trucks and military power applications consisting of an SOFC stack, reformer utilizing anode tailgate recycle for diesel fuel, and BOP components, with an expected efficiency of ≥ 30 percent (DC/LHV). Finally, in Phase III, Delphi-Battelle will fabricate and test a 5 kW Auxiliary Power Unit (APU) for mass-market automotive application consisting of an optimized SOFC stack, an optimized catalytic partial oxidation (CPO) reformer for gasoline, and BOP components, having an expected efficiency of ≥ 30 percent (DC/LHV) and a factory cost of ≤ $400/kW.

30 DIRECT ENERGY CONVERSION↗

Evaluation of a Combined Cyclone and Gas Filtration System for Particulate Removal in the Gasification Process

The Wabash gasification facility, owned and operated by sgSolutions LLC, is one of the largest single train solid fuel gasification facilities in the world capable of transforming 2,000 tons per day of petroleum coke or 2,600 tons per day of bituminous coal into synthetic gas for electrical power generation. The Wabash plant utilizes Phillips66 proprietary E-Gas™ Gasification Process to convert solid fuels such as petroleum coke or coal into synthetic gas that is fed to a combined cycle combustion turbine power generation facility. During plant startup in 1995, reliability issues were realized in the gas filtration portion of the gasification process. To address these issues, a slipstream test unit was constructed at the Wabash facility to test various filter designs, materials and process conditions for potential reliability improvement. The char filtration slipstream unit provided a way of testing new materials, maintenance procedures, and process changes without the risk of stopping commercial production in the facility. It also greatly reduced maintenance expenditures associated with full scale testing in the commercial plant. This char filtration slipstream unit was installed with assistance from the United States Department of Energy (built under DOE Contract No. DE-FC26-97FT34158) and began initial testing in November of 1997. It has proven to be extremely beneficial in the advancement of the E-Gas™ char removal technology by accurately predicting filter behavior and potential failure mechanisms that would occur in the commercial process. After completing four (4) years of testing various filter types and configurations on numerous gasification feed stocks, a decision was made to investigate the economic and reliability effects of using a particulate removal gas cyclone upstream of the current gas filtration unit. A paper study had indicated that there was a real potential to lower both installed capital and operating costs by implementing a char cyclone-filtration hybrid unit in the E-Gas™ gasification process. These reductions would help to keep the E-Gas™ technology competitive among other coal-fired power generation technologies. The Wabash combined cyclone and gas filtration slipstream test program was developed to provide design information, equipment specification and process control parameters of a hybrid cyclone and candle filter particulate removal system in the E-Gas™ gasification process that would provide the optimum performance and reliability for future commercial use. The test program objectives were as follows: 1. Evaluate the use of various cyclone materials of construction; 2. Establish the optimal cyclone efficiency that provides stable long term gas filter operation; 3. Determine the particle size distribution of the char separated by both the cyclone and candle filters. This will provide insight into cyclone efficiency and potential future plant design; 4. Determine the optimum filter media size requirements for the cyclone-filtration hybrid unit; 5. Determine the appropriate char transfer rates for both the cyclone and filtration portions of the hybrid unit; 6. Develop operating procedures for the cyclone-filtration hybrid unit; and, 7. Compare the installed capital cost of a scaled-up commercial cyclone-filtration hybrid unit to the current gas filtration design without a cyclone unit, such as currently exists at the Wabash facility.

01 COAL, LIGNITE, AND PEAT↗

Separation of CO2 from flue gas using electrochemical cells

Past research with high temperature molten carbonate electrochemical cells has shown that carbon dioxide can be separated from flue gas streams produced by pulverized coal combustion for power generation. However, the presence of trace contaminants, i.e., sulfur dioxide and nitric oxides, will impact the electrolyte within the cell. If a lower temperature cell could be devised that would utilize the benefits of commercially-available, upstream desulfurization and denitrification in the power plant, then this CO2 separation technique can approach more viability in the carbon sequestration area. Recent work has led to the assembly and successful operation of a low temperature electrochemical cell. In the proof-of-concept testing with this cell, an anion exchange membrane was sandwiched between gas-diffusion electrodes consisting of nickel-based anode electrocatalysts on carbon paper. When a potential was applied across the cell and a mixture of oxygen and carbon dioxide was flowed over the wetted electrolyte on the cathode side, a stream of CO2 to O2 was produced on the anode side, suggesting that carbonate/ bicarbonate ions are the CO2 carrier in the membrane. Since a mixture of CO2 and O2 is produced, the possibility exists to use this stream in oxy-firing of additional fuel. From this research, a novel concept for efficiently producing a carbon dioxide rich effluent from combustion of a fossil fuel was proposed. Carbon dioxide and oxygen are captured from the flue gas of a fossilfuel combustor by one or more electrochemical cells or cell stacks. The separated stream is then transferred to an oxy-fired combustor which uses the gas stream for ancillary combustion, ultimately resulting in an effluent rich in carbon dioxide. A portion of the resulting flow produced by the oxy-fired combustor may be continuously recycled back into the oxy-fired combustor for temperature control and an optimal carbon dioxide rich effluent

Keywords: Carbon dioxide sequestration Carbon capt↗

Ability of the total strain version of strainrange partitioning to characterize thermomechanical fatigue behavior

Strainrange partitioning (SRP) was originally developed on an inelastic strain basis for isothermal fatigue in the high-strain regime where the inelastic strainrange could be determined accurately. However, most power-generating equipment operates in the regime where the inelastic strains are small and difficult to determine with any degree of accuracy. This shortcoming led to the development of the total strain version of SRP (TS-SRP). Power-generating equipment seldom operates under isothermal conditions, and isothermal life prediction methods cannot be depended on to predict the lives of anisothermal cycles. To overcome this shortcoming, a method was proposed for extending TS-SRP to characterize anisothermal fatigue behavior and to predict the lives of thermomechanical fatigue (TMF) cycles using apppropriate anisothermal data. The viability of this method, referred to as TMF/TS-SRP, was demonstrated using TMF data for two high-temperature aerospace alloys. In this report, data from the literature are used to examine the ability of TMF/TS-SRP to characterize the failure and flow behavior of three low-strength, high-ductility alloys widely used for ground-based power-generating equipment. The three alloys are type 304 stainless steel, 1Cr-1Mo-0.25V steel, and 2.25Cr-1Mo steel. Because of the limited nature of the data, it was possible to evaluate the characterization, but not the predictive capability of TMF/TS-SRP.

Saltsman, James F.↗

Near-term implications of a ban on new coal-fired power plants in the United States

Large numbers of proposed new coal power generators in the United States have been cancelled, and some states have prohibited new coal power generators. We examine the effects on the U.S. electric power system of banning the construction of coal-fired electricity generators, which has been proposed as a means to reduce U.S. CO{sub 2} emissions. The model simulates load growth, resource planning, and economic dispatch of the Midwest Independent Transmission System Operator (ISO), Inc., Electric Reliability Council of Texas (ERCOT), and PJM under a ban on new coal generation and uses an economic dispatch model to calculate the resulting changes in dispatch order, CO{sub 2} emissions, and fuel use under three near-term (until 2030) future electric power sector scenarios. A national ban on new coal-fired power plants does not lead to CO{sub 2} reductions of the scale required under proposed federal legislation such as Lieberman-Warner but would greatly increase the fraction of time when natural gas sets the price of electricity, even with aggressive wind and demand response policies. 50 refs., 5 figs., 4 tabs.

20 FOSSIL-FUELED POWER PLANTS↗

Control of hybrid boosting in highly diluted internal combustion engines

A novel hybrid system enabling both flexible supercharging and limited torque assist is studied to mitigate transient response challenges of a turbocharged spark ignition engine equipped with low pressure exhaust gas recirculation. The hybrid system, called a power split supercharger (SC), is configured with a planetary gear set that splits the supercharging power between a small low-voltage electric motor and the engine crankshaft. The air path controller relies on the coordination of four actuators on the engine side and three low-level actuators on the hybrid boosting device. A decentralized control scheme is used in this work, in which the master–slave structure of the boost pressure controller decreases the turbo-lag associated with exhaust gas recirculation, while minimizing the SC operation for fuel economy. A vector reference governor is used to prevent compressor surge during engine tip-outs. In addition, the desired intake manifold pressure is modified to provide time for evacuating the exhaust gas recirculation and avoiding misfires when transitioning to low load, while the hybrid capability of the power split SC is used to recuperate the unwanted generated power. All controllers are validated on both a mean value engine model and a high-fidelity engine model. Practical challenges of implementing the vector reference governor to the highly nonlinear engine air path with pressure pulsations originating from the engine reciprocation are discussed and some solutions are proposed.

Engineering↗

WindSENSE Project Summary: FY2009-2011

Renewable resources, such as wind and solar, are providing an increasingly larger percentage of our energy needs. To successfully integrate these intermittent resources into the power grid while maintaining its reliability, we need to better understand the characteristics and predictability of the variability associated with these power generation resources. WindSENSE, a three year project at Lawrence Livermore National Laboratory, considered the problem of scheduling wind energy on the grid from the viewpoint of the control room operator. Our interviews with operators at Bonneville Power Administration (BPA), Southern California Edison (SCE), and California Independent System Operator (CaISO), indicated several challenges to integrating wind power generation into the grid. As the percentage of installed wind power has increased, the variable nature of the generation has become a problem. For example, in the Bonneville Power Administration (BPA) balancing area, the installed wind capacity has increased from 700 MW in 2006-2007 to over 1300 MW in 2008 and more than 2600 MW in 2009. To determine the amount of energy to schedule for the hours ahead, operators typically use 0-6 hour ahead forecasts, along with the actual generation in the previous hours and days. These forecasts are obtained from numerical weather prediction (NWP) simulations or based on recent trends in wind speed in the vicinity of the wind farms. However, as the wind speed can be difficult to predict, especially in a region with complex terrain, the forecasts can be inaccurate. Complicating matters are ramp events, where the generation suddenly increases or decreases by a large amount in a short time (Figure 1, right panel). These events are challenging to predict, and given their short duration, make it difficult to keep the load and the generation balanced. Our conversations with BPA, SCE, and CaISO indicated that control room operators would like (1) more accurate wind power generation forecasts for use in scheduling and (2) additional information that can be exploited when the forecasts do not match the actual generation. To achieve this, WindSENSE had two areas of focus: (1) analysis of historical data for better insights, and (2) observation targeting for improved forecasts. The goal was to provide control room operators with an awareness of wind conditions and energy forecasts so they can make well-informed scheduling decisions, especially in the case of extreme events such as ramps.

17 WIND ENERGY↗

Electrojet-independent ionospheric extremely low frequency/very low frequency wave generation by powerful high frequency waves

Results of extremely low frequency/very low frequency (ELF/VLF) wave generation by intensity-modulated high frequency (HF) heaters of 3.2 MHz in Gakona, Alaska, near local solar noon during a geomagnetic quiet time, are presented to support an electrojet-independent ELF/VLF wave generation mechanism. The modulation was set by splitting the HF transmitter array into two subarrays; one was run at cw full power and the other run alternatively at 50% and 100% power modulation by rectangular waves of 2.02, 5, 8, and 13 kHz. The most effective generation was from the X-mode heater with 100% modulation. While the 8 kHz radiation has the largest wave amplitude, the spectral intensity of the radiation increases with the modulation frequency, i.e., 13 kHz line is the strongest. Ionograms recorded significant virtual height spread of the O-mode sounding echoes. The patterns of the spreads and the changes of the second and third hop virtual height traces caused by the O/X-mode heaters are distinctively different, evidencing that it is due to differently polarized density irregularities generated by the filamentation instability of the O/X-mode HF heaters.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Small-RPS Enabled Mars Rover Concept

Both the MER and the Mars Pathfinder rovers operated on Mars in an energy-limited mode, since the solar panels generated power during daylight hours only. At other times the rovers relied on power stored in batteries. In comparison, Radioisotope Power Systems (RPS) offer a power-enabled paradigm, where power can be generated for long mission durations (measured in years), independently from the Sun, and on a continuous basis. A study was performed at PL to assess the feasibility of a small-RPS enabled MER-class rover concept and any associated advantages of its mission on Mars. The rover concept relied on design heritage from MER with two significant changes. First, the solar panels were replaced with two single GPHS module based small-RPSs. Second, the Mossbauer spectroscope was substituted with a laser Raman spectroscope, in order to move towards MEPAG defined astrobiology driven science goals. The highest power requirements were contributed to mobility and telecommunication type operating modes, hence influencing power system sizing. The resulting hybrid power system included two small-RPSs and two batteries. Each small-RPS was assumed to generate 50We of power or 62OWh/sol of energy (BOL), comparable to that of MER. The two 8Ah batteries were considered available during peak power usage. Mission architecture, power trades, science instruments, data, communication, thermal and radiation environments, mobility, mass issues were also addressed. The study demonstrated that a new set of RPS-enabled rover missions could be envisioned for Mars exploration within the next decade, targeting astrobiology oriented science objectives, while powered by 2 to 4 GPHS modules.

Mars exploration↗

Electrical Systems of Pumped Storage Hydropower Plants: Electrical Generation, Machines, Power Electronics, and Power Systems

Adjustable-speed (AS) pumped storage hydropower (PSH) technology has the potential to become a large, consistent contributor to grid stability enabling higher penetrations of wind and solar energy on the future U.S. power system. AS-PSH has high-value characteristics, such as fast response to provide ancillary services to the grid, because it is a power converter interface with the grid (like battery storage), but at the same time it has the energy content large enough to supply both short-term (seconds-to-minutes) and long-term (minutes-to-hours) of energy needs, like more conventional power plants. However, designs must be optimized to lower the capital expenditure (CapEx) and to provide a high-quality grid interface capability (e.g. power quality, ancillary service provider, fault-tolerant or fault ride-through capability), which is a primary factor in the acceptance of AS-PSH into a utility’s generation mix. This CapEx will be greatly affected by the cost savings associated with the civil structure, turbine design, power electronics, control systems, or unique generator designs. A holistic design must be considered to get a full picture of the benefits of the technology proposed. The AS-PSH can be controlled to reduce the impact of transient disturbance on a power system and at the same time can be controlled to minimized subsequent component fatigue and potential oscillation modes within the plant, with the overall impact in reducing the operational expenditures (OpEx).Generating clean power to meet standards such as Institute of Electrical and Electronics Engineers (IEEE) 519 and International Electrotechnical Commission (IEC) 1000-3-2 will be a continuing challenge. For many technology developers, however, improved AS-PSH technologies will become a key component of generator-storage systems of the future given the prospects of increased performance and decreasing costs, and the ever-increasing penetration of renewables (e.g wind power and solar power).

13 HYDRO ENERGY↗

NASA's Habitation Development Status: Current Concepts and ISRU Opportunities

Introduction: The National Aeronautics and Space Administration (NASA) is embarking on a bold journey to return humankind to the Moon and onward to Mars with innovative commercial, international, and academic partnerships. Under the Artemis series of missions, NASA seeks to establish sustained human exploration of deep space through an objectives-based approach. This approach drives the identification of needed system functionality and the current and future capabilities which will eventually allow humanity to sustainably live beyond Earth. Providing evolvable and scalable habitation is a cornerstone function that calls for the collection and integration of current, developmental, and future technologies that can meet near-term exploration needs while growing into long-term sustained presence. NASA is advancing in-space habitation through its Next Space Technologies for Exploration Partnerships (NextSTEP) model while designing lunar, Mars transit, and Mars surface habitat government reference concepts for Artemis missions. These efforts have unveiled possible near-term opportunities for the in-space resource utilization community if human habitation is considered a future customer of space resources. NextSTEP Habitation Development: NASA is closely working with commercial partners under its NextSTEP Appendix A model to advance habitation systems in the arena of inflatable and composite habitation structures. Such efforts promise efficiencies in volumetric packaging and overall spacecraft mass respectively. Recent testing by commercial partners have helped to quantify possible failure mechanisms for inflatable structures while advancing their technology towards eventual flight certification. The advancement of such Class II habitation structures, in which the habitat is only fully deployed once in-space or on a planetary surface, is critical to providing increased habitable volume for long-duration missions with no additional mass penalties. The progression of such technology is infused into NASA’s government reference concepts for notional deep space habitation concepts. Current Government Reference Concepts: To best inform the formulation of future collaborative solicitations, NASA employs the practice of internally developing reference concepts for future exploration elements. These concepts aid in identifying the functions and capabilities needed to complete NASA missions as well as feasible solutions within the timeframe needed. Government reference concepts for a lunar Surface Habitat, Mars Transit Habitat, and Mars Sur-face Habitat are continuously being developed and updated to better guide the Agency’s overall exploration architecture. Lunar Surface Habitat. As NASA returns to the Moon, it is evaluating possible lunar surface habitation concepts. The Surface Habitat (SH) reference concept entails a hybrid metallic-inflatable structure capable of initially housing two crew for surface stays of up to 30 days in duration. While initial missions may span ~7 days in duration, consideration is being given to expanding SH’s capability to support a crew of four for up to 60 days over its 15-year design life. Functionally, the SH serves as a ‘hub’ for all Artemis crewed surface operations, providing internal volume for maintenance, medical, logistics, science utilization, and extravehicular activity (EVA) support in addition to core habitation functionality such as environmental control and life support (ECLS) and power generation and distribution among many others. Additionally, NASA has entered a study agreement with the Italian Space Agency (Agenzia Spaziale Italiana – ASI) to investigation a possible Multi-Purpose Habitat (MPH) as an additional or augmenting habit-able element for the lunar surface. Mars Transit Habitat. NASA’s current architectural concept for initial human missions to Mars entails the utilization of a transit habitat (TH) to transport a four-person crew to and from Mars orbit, departing from and returning to a lunar near-rectilinear halo orbit (NRHO), over the course of a ~1,200-day mission. While holding a similar 15-year design lifetime, TH will also support a series of analog mission activities in NRHO to gradually test the systems and interaction with lunar surface elements, some of which may be adapted for Mars surface exploration. Holding similar functional capabilities as SH, TH is sized to support much longer durations in space and greater logistical independence. Mars Surface Habitat. NASA is still exploring the concept of operations for initial crewed missions to Mars. As such, the Mars Surface Habitat (MSH) concept is still in its infancy as options for mobile, pressurized habitation and stationary habitats are being explored. It is expected MSH will leverage heavily from the lunar SH and possible lunar pressurized rover, however the very different Martian environment will likely necessitate modifications. ISRU Opportunities: Despite the advancements under NASA’s NextSTEP habitation work and continually optimized reference concepts, NASA is facing near-term mass and power challenges that may create opportunities to the ISRU community by providing yet another possible customer for space resources. While NASA desires to use regenerative ECLS systems (ECLSS) for all habitation concepts, their operation comes with initial mass penalties and maintenance overheads when compared to simpler open-loop architectures. Because of this, NASA is currently pro-posing an open-loop, consumables-based architecture for its surface habitats to achieve initial launch and delivery lander mass targets while scarring for the in-corporation of regenerative ECLSS to meet longer mission durations and sustained presence. With such an architecture, oxygen and potable water are needed consumables, which initial ISRU systems may be able to provide in a pilot capacity. Although the TH is expecting to utilize regenerative ECLSS, advancements in lunar surface-based ISRU and possible re-supply of spacecraft in lunar or Mars orbit could significantly reduce the logistical need for ECLSS related spares on TH and possibly allow a similar open-loop and consumables-based architecture. In addition to ECLSS mass concerns, the SH is facing challenges with energy storage to support operations over periods of darkness exceeding 100 hours. Both battery and fuel cell-based power architectures are being traded, opening options for external power generation and energy storage. One possibility is ISRU-produced H2 and O2 feeding external primary fuel cell systems which could supplement habitation power generation while reducing initial mass and volume until much more powerful fission power systems might be deployed. Conclusion: Significant advancements are being made in evolvable habitation concepts that span from near-term technologies, such as inflatable structures under NextSTEP, to potentially revolutionary capabilities like the lunar surface construction as funded through the Moon-to-Mars Planetary Autonomous Construction Technologies (MMPACT) project. As NASA investigates both heritage capabilities and rap-idly advancing, disruptive technologies, there are likely many near-term opportunities for initial ISRU capabilities to significantly aid human habitation and increase self-sufficiency beyond Earth.

habitation↗

NASA's Habitation Development Status: Current Concepts and ISRU Opportunities

Introduction: The National Aeronautics and Space Administration (NASA) is embarking on a bold journey to return humankind to the Moon and onward to Mars with innovative commercial, international, and academic partnerships [1]. Under the Artemis series of missions, NASA seeks to establish sustained human exploration of deep space through an objectives-based approach [2]. This approach drives the identification of needed system functionality and the current and future capabilities which will eventually allow humanity to sustainably live beyond Earth. Providing evolvable and scalable habitation is a cornerstone function that calls for the collection and integration of current, developmental, and future technologies that can meet near-term exploration needs while growing into long-term sustained presence. NASA is advancing in-space habitation through its Next Space Technologies for Exploration Partnerships (NextSTEP) model while designing lunar, Mars transit, and Mars surface habitat government reference concepts for Artemis missions. These efforts have unveiled possible near-term opportunities for the in-space resource utilization community if human habitation is considered a future customer of space resources. NextSTEP Habitation Development: NASA is closely working with commercial partners under its NextSTEP Appendix A model to advance habitation systems in the arena of inflatable and composite habitation structures. Such efforts promise efficiencies in volumetric packaging and overall spacecraft mass respectively. Recent testing by commercial partners have helped to quantify possible failure mechanisms for inflatable structures while advancing their technology towards eventual flight certification. The advancement of such Class II habitation structures, in which the habitat is only fully deployed once in-space or on a planetary surface [3], is critical to providing increased habitable volume for long-duration missions with no additional mass penalties. The progression of such technology is infused into NASA’s government reference concepts for notional deep space habitation concepts. Current Government Reference Concepts: To best inform the formulation of future collaborative solicitations, NASA employs the practice of internally developing reference concepts for future exploration elements. These concepts aid in identifying the functions and capabilities needed to complete NASA missions as well as feasible solutions within the timeframe needed. Government reference concepts for a lunar Surface Habitat, Mars Transit Habitat, and Mars Sur-face Habitat are continuously being developed and updated to better guide the Agency’s overall exploration architecture. Lunar Surface Habitat. As NASA returns to the Moon, it is evaluating possible lunar surface habitation concepts. The Surface Habitat (SH) reference concept entails a hybrid metallic-inflatable structure capable of initially housing two crew for surface stays of up to 30 days in duration [4]. While initial missions may span ~7 days in duration, consideration is being given to expanding SH’s capability to support a crew of four for up to 60 days over its 15-year design life [5]. Functionally, the SH serves as a ‘hub’ for all Artemis crewed surface operations, providing internal volume for maintenance, medical, logistics, science utilization, and extravehicular activity (EVA) support in addition to core habitation functionality such as environmental control and life support (ECLS) and power generation and distribution among many others. Additionally, NASA has entered a study agreement with the Italian Space Agency (Agenzia Spaziale Italiana – ASI) to investigation a possible Multi-Purpose Habitat (MPH) as an additional or augmenting habit-able element for the lunar surface [6]. Mars Transit Habitat. NASA’s current architectural concept for initial human missions to Mars entails the utilization of a transit habitat (TH) to transport a four-person crew to and from Mars orbit, departing from and returning to a lunar near-rectilinear halo orbit (NRHO), over the course of a ~1,200-day mission [5]. While holding a similar 15-year design lifetime, TH will also support a series of analog mission activities in NRHO to gradually test the systems and interaction with lunar surface elements, some of which may be adapted for Mars surface exploration. Holding similar functional capabilities as SH, TH is sized to support much longer durations in space and greater logistical independence. Mars Surface Habitat. NASA is still exploring the concept of operations for initial crewed missions to Mars. As such, the Mars Surface Habitat (MSH) concept is still in its infancy as options for mobile, pressurized habitation and stationary habitats are being explored. It is expected MSH will leverage heavily from the lunar SH and possible lunar pressurized rover, however the very different Martian environment will likely necessitate modifications. ISRU Opportunities: Despite the advancements under NASA’s NextSTEP habitation work and continually optimized reference concepts, NASA is facing near-term mass and power challenges that may create opportunities to the ISRU community by providing yet another possible customer for space resources. While NASA desires to use regenerative ECLS systems (ECLSS) for all habitation concepts, their operation comes with initial mass penalties and maintenance overheads when compared to simpler open-loop architectures. Because of this, NASA is currently pro-posing an open-loop, consumables-based architecture for its surface habitats to achieve initial launch and delivery lander mass targets while scarring for the in-corporation of regenerative ECLSS to meet longer mission durations and sustained presence. With such an architecture, oxygen and potable water are needed consumables, which initial ISRU systems may be able to provide in a pilot capacity. Although the TH is expecting to utilize regenerative ECLSS, advancements in lunar surface-based ISRU and possible re-supply of spacecraft in lunar or Mars orbit could significantly reduce the logistical need for ECLSS related spares on TH and possibly allow a similar open-loop and consumables-based architecture. Table 1 Notional ECLSS consumables per mission use for SH and TH [5]. SH (28-day) Open Loop: Water (kg) 288 | Oxygen (kg) 30 TH (1110-day) Closed-Loop: Water (kg) 182 | Oxygen (kg) 123 In addition to ECLSS mass concerns, the SH is facing challenges with energy storage to support operations over periods of darkness exceeding 100 hours. Both battery and fuel cell-based power architectures are being traded, opening options for external power generation and energy storage. One possibility is ISRU-produced H2 and O2 feeding external primary fuel cell systems which could supplement habitation power generation while reducing initial mass and volume until much more powerful fission power systems might be deployed. Conclusion: Significant advancements are being made in evolvable habitation concepts that span from near-term technologies, such as inflatable structures under NextSTEP, to potentially revolutionary capabilities like the lunar surface construction as funded through the Moon-to-Mars Planetary Autonomous Construction Technologies (MMPACT) project [7]. As NASA investigates both heritage capabilities and rap-idly advancing, disruptive technologies, there are likely many near-term opportunities for initial ISRU capabilities to significantly aid human habitation and increase self-sufficiency beyond Earth.

habitation↗

Underwater thermomagnetic generator for remote marine thermal energy harvesting and sensing

Thermomagnetic generators offer a promising approach for sustainable power generation in remote marine environments. Here, this study presents the design, thermal modeling, and experimental validation of a passively driven underwater thermomagnetic generator developed for powering ocean observation and monitoring sensors. The generator was evaluated under varying working fluids, thermal boundary conditions, and extended operation to assess real-world applicability. Two fluids, deionized water and silicone-based Thermal C5, were tested under simulated shallow- and deep-ocean conditions. Deionized water outperformed Thermal C5, especially in colder environments (~5°C), achieving a peak output of 2.7 mW due to larger temperature gradients and enhanced convective-evaporative heat transfer. Long-duration tests revealed a transient evaporation-condensation cycle that temporarily reduced rotor immersion and performance before stabilizing. The generator powered commercial marine sensors for over 6 h without external batteries, demonstrating the viability of compact, passively cooled thermomagnetic systems for autonomous, off-grid marine sensing.

13 HYDRO ENERGY↗