Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Fractional watt Vuillemier cryogenic refrigerator program engineering notebook. Volume 2: Stress analysis

A structural analysis performed on the 1/4-watt cryogenic refrigerator. The analysis covered the complete assembly except for the cooling jacket and mounting brackets. Maximum stresses, margin of safety, and natural frequencies were calculated for structurally loaded refrigerator components shown in assembly drawings. The stress analysis indicates that the design is satisfactory for the specified vibration environment, and the proof, burst, and normal operating loads.

Miller, W. S.↗

Strain intensity factor approach for predicting the strength of continuously reinforced metal matrix composites

A method was previously developed to predict the fracture toughness (stress intensity factor at failure) of composites in terms of the elastic constants and the tensile failing strain of the fibers. The method was applied to boron/aluminum composites made with various proportions of 0 to + or - 45 deg plies. Predicted values of fracture toughness were in gross error because widespread yielding of the aluminum matrix made the compliance very nonlinear. An alternate method was developed to predict the strain intensity factor at failure rather than the stress intensity factor because the singular strain field was not affected by yielding as much as the stress field. Strengths of specimens containing crack-like slits were calculated from predicted failing strains using uniaxial stress-strain curves. Predicted strengths were in good agreement with experimental values, even for the very nonlinear laminates that contained only + or - 45 deg plies. This approach should be valid for other metal matrix composites that have continuous fibers.

Poe, C. C., Jr.↗

ON HYDROMAGNETIC STRESSES IN ACCRETION DISK BOUNDARY LAYERS

Detailed calculations of the physical structure of accretion disk boundary layers, and thus their inferred observational properties, rely on the assumption that angular momentum transport is opposite to the radial angular frequency gradient of the disk. The standard model for turbulent shear viscosity satisfies this assumption by construction. However, this behavior is not supported by numerical simulations of turbulent magnetohydrodynamic (MHD) accretion disks, which show that angular momentum transport driven by the magnetorotational instability (MRI) is inefficient in disk regions where, as expected in boundary layers, the angular frequency increases with radius. In order to shed light on physically viable mechanisms for angular momentum transport in this inner disk region, we examine the generation of hydromagnetic stresses and energy density in differentially rotating backgrounds with angular frequencies that increase outward in the shearing-sheet framework. We isolate the modes that are unrelated to the standard MRI and provide analytic solutions for the long-term evolution of the resulting shearing MHD waves. We show that, although the energy density of these waves can be amplified significantly, their associated stresses oscillate around zero, rendering them an inefficient mechanism to transport significant angular momentum (inward). These findings are consistent with the results obtained in numerical simulations of MHD accretion disk boundary layers and challenge the standard assumption of efficient angular momentum transport in the inner disk regions. This suggests that the detailed structure of turbulent MHD accretion disk boundary layers could differ appreciably from those derived within the standard framework of turbulent shear viscosity.

79 ASTRONOMY AND ASTROPHYSICS↗

Four-point Bend Testing of Irradiated Monolithic U-10Mo Fuel

This paper presents results of recently completed studies aimed at characterizing the mechanical properties of irradiated U-10Mo fuel in support of monolithic base fuel qualification. Mechanical properties were evaluated in four-point bending. Specimens were taken from fuel plates irradiated in the RERTR-12 and AFIP-6 Mk. II irradiation campaigns, and tests were conducted in the Hot Fuel Examination Facility (HFEF) at Idaho National Laboratory (INL). The monolithic fuel plates consist of a U-10Mo fuel meat covered with a Zr diffusion barrier layer fabricated by co-rolling, clad in 6061 Al using a hot isostatic press (HIP) bonding process. Specimens exhibited nominal (fresh) fuel meat thickness ranging from 0.25 mm to 0.64 mm, and fuel plate average burnup ranged from approximately 0.4 x 1021 fissions/cm 3 to 6.0 x 1021 fissions/cm 3 . After sectioning the fuel plates, the 6061 Al cladding was removed by dissolution in concentrated NaOH. Pre- and post-dissolution dimensional inspections were conducted on test specimens to facilitate accurate analysis of bend test results. Four-point bend testing was conducted on the HFEF Remote Load Frame at a crosshead speed of 0.1 mm/min using custom-designed test fixtures and calibrated load cells. All specimens exhibited substantially linear elastic behavior and failed in a brittle manner. The influence of burnup on the observed slope of the stress-strain curve and the calculated fracture strength is discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Implementation of equivalent domain integral method in the two-dimensional analysis of mixed mode problems

An equivalent domain integral (EDI) method for calculating J-intergrals for two-dimensional cracked elastic bodies is presented. The details of the method and its implementation are presented for isoparametric elements. The total and product integrals consist of the sum of an area of domain integral and line integrals on the crack faces. The line integrals vanish only when the crack faces are traction free and the loading is either pure mode 1 or pure mode 2 or a combination of both with only the square-root singular term in the stress field. The EDI method gave accurate values of the J-integrals for two mode I and two mixed mode problems. Numerical studies showed that domains consisting of one layer of elements are sufficient to obtain accurate J-integral values. Two procedures for separating the individual modes from the domain integrals are presented. The procedure that uses the symmetric and antisymmetric components of the stress and displacement fields to calculate the individual modes gave accurate values of the integrals for all problems analyzed. The EDI method when applied to a problem of an interface crack in two different materials showed that the mode 1 and mode 2 components are domain dependent while the total integral is not. This behavior is caused by the presence of the oscillatory part of the singularity in bimaterial crack problems. The EDI method, thus, shows behavior similar to the virtual crack closure method for bimaterial problems.

Raju, I. S.↗

Lubrication of nonconformal contacts

Minimum film thickness results for piezoviscous-rigid regime of lubrication are developed for a compressible Newtonian fluid with Roelands viscosity. The results provide a basis for the analysis and design of a wide range of machine elements operating in the piezoviscous-rigid regime of lubrication. A new numerical method of calculating elastic deformation in contact stresses is developed using a biquadratic polynomial to approximate the pressure distribution on the whole domain analyzed. The deformation of every node is expressed as a linear combination of the nodal pressures whose coefficients can be combined into an influence coefficient matrix. This approach has the advantages of improved numerical accuracy, less computing time and smaller storage size required for influence matrix. The ideal elastohydrodynamic lubrication is extended to real bearing systems in order to gain an understanding of failure mechanisms in machine elements. The improved elastic deformation calculation is successfully incorporated into the EHL numerical scheme. Using this revised numerical technique and the flow factor model developed by Patir and Cheng (1978) the surface roughness effects on the elastohydrodynamic lubrication of point contact is considered. Conditions typical of an EHL contact in the piezoviscous-elastic regime entrained in pure rolling are investigated. Results are compared with the smooth surface solutions. Experiments are conducted to study the transient EHL effects in instrument ball bearings.

Jeng, Y. R.↗

Strain intensity factor approach for predicting the strength of continuously reinforced metal matrix composites

A method was previously developed to predict the fracture toughness (stress intensity factor at failure) of composites in terms of the elastic constants and the tensile failing strain of the fibers. The method was applied to boron/aluminum composites made with various proportions of 0 deg and +/- 45 deg plies. Predicted values of fracture toughness were in gross error because widespread yielding of the aluminum matrix made the compliance very nonlinear. An alternate method was develolped to predict the strain intensity factor at failure rather than the stress intensity factor because the singular strain field was not affected by yielding as much as the stress field. Far-field strains at failure were calculated from the strain intensity factor, and then strengths were calculated from the far-field strains using uniaxial stress-strain curves. The predicted strengths were in good agreement with experimental values, even for the very nonlinear laminates that contained only +/- 45 deg plies. This approach should be valid for other metal matrix composites that have continuous fibers.

Poe, Clarence C., Jr.↗

Flat-space holography and correlators of Robinson–Trautman stress tensor

We propose a quasi-local stress tensor for the four-dimensional asymptotically flat Robinson–Trautman geometries by taking the flat-space limit from the corresponding asymptotically AdS solutions. This stress tensor results in the correct charges of the generators of BMS symmetry if we define conformal infinity by an anisotropic scaling of the metric components. Using flat-space holography this stress tensor is related to expectation values of the stress tensor in a dual field theory called BMS-invariant field theory (BMSFT). We also calculate the two and three point functions of the proposed stress tensor.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Bearing tester data compilation, analysis, and reporting and bearing math modeling

The Shaberth bearing analysis computer program was developed for the analysis of jet engine shaft/bearing systems operating above room temperature with normal hydrocarbon lubricants. It is also possible to use this tool to evaluate the shaft bearing systems operating in cryogenics. Effects such as fluid drag, radial temperature gradients, outer race misalignments and clearance changes were simulated and evaluated. In addition, the speed and preload effects on bearing radial stiffness was evaluated. The Shaberth program was also used to provide contact stresses from which contact geometry was calculated to support other analyses such as the determination of cryogenic fluid film thickness in the contacts and evaluation of surface and subsurface stresses necessary for bearing failure evaluation. This program was a vital tool for the thermal analysis of the bearing in that it provides the heat generation rates at the rolling element/race contacts for input into a thermal model of the bearing/shaft assembly.

Source record↗

The Distribution of Lift Over Wing Tips and Ailerons

This investigation was carried out in the 5-foot wind tunnel of the Langley Memorial Aeronautical Laboratory for the purpose of obtaining more complete information on the distribution of lift between the ends of wing spars, the stresses in ailerons, and the general subject of airflow near the tip of a wing. It includes one series of tests on four models without ailerons, having square, elliptical, and raked tips respectively, and a second series of positively and negatively raked wings with ailerons adjusted to different settings. The results show that negatively raked tips give a more uniform distribution of air pressure than any of the other three arrangements, because the tip vortex does not disturb the flow at the trailing edge. Aileron loads are found to be less severe on wings with negative application to the calculation of aileron and wing stresses and also to facilitate the proper distribution of load in sand testing. Contour charts show in great detail the complex distribution lift over the wing.

Bacon, David L↗

Analysis of wing truss stresses including the effect of redundancies

Airplane wing trusses are generally designed to contain redundant members (stagger wires and external drag wires) which, according to common practice, are not taken into account in calculations, so as to simplify the stress analysis by rendering the structure statically determinate. A more accurate method, in which the redundancies are included, involves a solution by means of Castigliano's method of least work. For the purpose of demonstrating the practical application of the method of least work this report presents examples for stresses of several cases of loading worked out for a structure similar to that of the Curtiss JN-4h. Case 1 was taken as the condition of velocity of 100 miles per hour combined with the angle of attack of maximum lift. Case 1a assumed the same loading but neglected the distortion of wooden members in the least-work analysis. So little error was involved in case 1a that this simplified method was employed for each succeeding case. Case 2 assumed a diving speed of 120 miles per hour and an angle of attack of no lift. Case 3 was worked out for the conditions imposed by the sand load recommended in NACA technical note no. 6.

Warner, E P↗

An equivalent domain integral for analysis of two-dimensional mixed mode problems

An equivalent domain integral (EDI) method for calculating J-integrals for two-dimensional cracked elastic bodies subjected to mixed mode loading is presented. The total and product integrals consist of the sum of an area or domain integral and line integrals on the crack faces. The EDI method gave accurate values of the J-integrals for two mode I and two mixed mode problems. Numerical studies showed that domains consisting of one layer of elements are sufficient to obtain accurate J-integral values. Two procedures for separating the individual modes from the domain integrals are presented. The procedure that uses the symmetric and antisymmetric components of the stress and displacement fields to calculate the individual modes gave accurate values of the integrals for all the problems analyzed.

Raju, I. S.↗

Elastic-plastic conductor damage evaluation at over 0.4% strain using a high-stress REBCO coil

Abstract Recent reports on screening current stress simulations of high-field REBCO magnets frequently present peak stresses over 1 GPa. However, this result is probably an unrealistic artifact of purely elastic calculations, considering the macroscopic yield and fracture stresses of approximately 900 MPa and less than 1.1 GPa for Hastelloy substrate-coated conductors. Here, we evaluate elastic-plastic conductor damage at over 0.4% strain using a high-stress REBCO coil exposed to a high field to explore this elastic-plastic regime. The coil was located off-center in a low-temperature superconductor magnet so as to induce a significant screening current in the enhanced radial field. Voltage taps, a Hall sensor, and two strain gauges were used for the instrumentation. We obtained strains exceeding 0.4% near the outward edge during the coil current charge from 350 A to 390 A, where the coil was exposed to external axial and radial magnetic fields of 13 T and 0.5 T. Post mortem results showed wavy plastic deformation, electrical damage, and REBCO defects. An elastic-plastic simulation reproduced the measured strains and predicted that ∼1 GPa stress is sufficient to induce ∼0.9% strain, thus validating our initial concerns with purely elastic models. This paper provides our experimental and simulation results.

Bang, Jeseok (ORCID:0000000247616334)↗

On-Orbit Glass Stress Measurement Tool Development

Exposed window surfaces on-orbit are vulnerable to a variety of damage including impacts. These impacts impart stress into the panes and reduce the remaining life of the window. Spacecraft windows are evaluated before and after flight to determine the minimum strength of the glass prior to launch. Currently, no method exists to accurately evaluate the windows on-orbit. An on-orbit optical system is under development to evaluate spacecraft windowpane material for remaining flight life by directly measuring the stress in the glass. This optical system builds on the industry-standard practice of calculating the amount of impact-induced stress through birefringence measurement. In industry, the birefringence is imaged through the pane with a detector and light source on opposite sides. On-orbit, there is only access to one side of the pane. This system has been designed to image birefringence by reflecting the light off the pane to a detector on the same side of the glass. Previous studies have shown a correlation between material stress distribution and the associated K-value. This system is designed to determine low strength areas which can be caused by defects due to impact damage. Glass samples will be imaged and broken in order to correlate impact-induced stress to the fracture strength of the material. Once this correlation is determined, a quantitative assessment of the stress areas in spacecraft windows will occur prior to and during mission operations to reliably determine the overall strength of the glass.

Max J Schneiderman↗

Development of Constitutive Relationship for Thermomechanical Processing of Al-SiC Composite Eliminating Deformation Heating

Constitutive equations are useful for computational or numerical tools in describing the thermomechanical behavior of Al/SiC composites to develop the lightweight component using bulk metal forming. In this study, the uniaxial compression test of powder metallurgy-based Al/7 vol.% SiCp composite samples in the temperature range of 250-500 °C and at the strain rates of 0.001, 0.007, 0.05, 0.3, 2.2 and 15 s{sup −1} was performed on a Gleeble-3800 thermomechanical simulator. An equation correlating actual (measured) temperature with the true stress in real time has been established for each of the strain rates. Further, the true stress was corrected by eliminating the effect of deformation heating using this equation based on the experimental observations. The temperature-corrected true stress data were then used for development of constitutive equations using the Arrhenius model, strain-compensated Arrhenius model and modified Johnson–Cook (m-JC) model. The material parameters in the m-JC model were calculated at different combinations of temperatures and strain rates. The established constitutive equations are validated with temperature-corrected true stress from the experiment. Further, these equations are verified with the experimental true stress that was obtained using different inputs of temperatures and strain rates in a compression test. The correlation coefficient (R) and absolute average relative error reflect the accuracy of constitutive models. The result indicates that the calculated true stress by the established strain-compensated Arrhenius model is in good agreement with that of experimentally measured true stress with a correlation coefficient of 0.996 and relative error of 3.83%.

36 MATERIALS SCIENCE↗

Effect of crack curvature on stress intensity factors for ASTM standard compact tension specimens

The stress intensity factors (SIF) are calculated using the method of lines for the compact tension specimen in tensile and shear loading for curved crack fronts. For the purely elastic case, it was found that as the crack front curvature increases, the SIF value at the center of the specimen decreases while increasing at the surface. For the higher values of crack front curvatures, the maximum value of the SIF occurs at an interior point located adjacent to the surface. A thickness average SIF was computed for parabolically applied shear loading. These results were used to assess the requirements of ASTM standards E399-71 and E399-81 on the shape of crack fronts. The SIF is assumed to reflect the average stress environment near the crack edge.

Alam, J.↗

Experimental Studies of Anisotropy on Borehole Breakouts in Mancos Shale

Calculating the size and orientation of borehole breakouts is one of the key methods for determining the orientation and magnitudes of the in situ stresses in the subsurface. To better understand the effects of anisotropy on borehole breakouts, experiments were conducted on Mancos Shale, a finely laminated mudrock. A novel testing configuration was developed to conduct borehole breakout experiments in a standard triaxial vessel and load frame. Samples were prepared at three different orientations and deformed under 6.9 to 20.7 MPa confining pressure. The results show a variation of peak strength and breakout geometry depending on the lamination orientation. Samples deformed parallel to laminations failed at a higher maximum compressive stress than samples deformed perpendicular to laminations, which were stronger than inclined samples. These relationships are quantified by a cosine-based failure envelope. Observed breakout shapes in perpendicular samples are V-shaped and symmetric around the borehole, which advance as a series of fractures of increasing size into the sidewalls. In inclined samples, fractures form along weaker laminations planes and grow in an en echelon pattern towards the axial stress direction. In parallel samples, long fractures grow from the wellbore towards the axial stress direction. The observed geometries point to potential sources of error in calculating in situ stresses from borehole breakouts.

58 GEOSCIENCES↗

Large-scale patterns of eolian sediment transport on Venus - Predictions for Magellan

The atmosphere of Venus is likely to exert a major influence on the surface. Arecibo and Venera 15/16 observations of the population of impact craters with bright halos give direct evidence of surface modification, on the scale of centimeters, to smooth the surface on time scales of 50 - 250 my. Both chemical and mechanical modifications probably occur. Diurnal winds in the planetary boundary layer can transport particles. Using boundary layer theory, including the effects of topography, surface stresses and resulting transport and deposition of sand-size particles are calculated. Regional slopes are sites of largest surface stresses. Sand will be generally transported downhill, although there is a preferential net transport from east to west, in the same direction as the atmospheric superrotation. It is predicted here that streaks may be seen in the Magellan radar images which will indicate directions of net eolian transport on the surface of Venus.

Saunders, R. S.↗