Search NASA⌕ Search

SEARCH · Search NASA

Results for “accelerometers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Computer programs for the calculation of dual sting pitch and roll angles required for an articulated sting to obtain angles of attack and sideslip on wind-tunnel models

Two programs were developed to calculate the pitch and roll position of the conventional sting drive and the pitch of a high angle articulated sting to position a wind tunnel model at the desired angle of attack and sideslip and position the model as near as possible to the centerline of the tunnel. These programs account for the effects of sting offset angles, sting bending angles, and wind-tunnel stream flow angles. In addition, the second program incorporates inputs form on-board accelerometers that measure model pitch and roll with respect to gravity. The programs are presented and a description of the numerical operation of the programs with a definition of the variables used in the programs is given.

Peterson, John B., Jr.↗

Final STS-35 Columbia descent BET products and results for LaRC OEX investigations

Final STS-35 'Columbia' descent Best Estimate Trajectory (BET) products have been developed for Langley Research Center (LaRC) Orbiter Experiments (OEX) investigations. Included are the reconstructed inertial trajectory profile; the Extended BET, which combines the inertial data and, in this instance, the National Weather Service atmospheric information obtained via Johnson Space Center; and the Aerodynamic BET. The inertial BET utilized Inertial Measurement Unit 1 (IMU1) dynamic measurements for deterministic propagation during the ENTREE estimation process. The final estimate was based on the considerable ground based C-band tracking coverage available as well as Tracking Data and Relay Satellite System (TDRSS) Doppler data, a unique use of the latter for endo-atmospheric flight determinations. The actual estimate required simultaneous solutions for the spacecraft position and velocity, spacecraft attitude, and six IMU parameters - three gyro biases and three accelerometer scale factor correction terms. The anchor epoch for this analysis was 19,200 Greenwich Mean Time (GMT) seconds which corresponds to an initial Shuttle altitude of approximately 513 kft. The atmospheric data incorporated were evaluated based on Shuttle derived considerations as well as comparisons with other models. The AEROBET was developed based on the Extended BET, the measured spacecraft configuration information, final mass properties, and the final Orbiter preoperation databook. The latter was updated based on aerodynamic consensus incrementals derived by the latest published FAD. The rectified predictions were compared versus the flight computed values and the resultant differences were correlated versus ensemble results for twenty-two previous STS entry flights.

Oakes, Kevin F.↗

Fiber-optic push-pull sensor systems

Fiber-optic push-pull sensors are those which exploit the intrinsically differential nature of an interferometer with concommitant benefits in common-mode rejection of undesired effects. Several fiber-optic accelerometer and hydrophone designs are described. Additionally, the recent development at the Naval Postgraduate School of a passive low-cost interferometric signal demodulator permits the development of economical fiber-optic sensor systems.

Gardner, David L.↗

Suborbital missions: The Joust

Joust 1 will carry a payload of 10 experiments. The experiments in the payload module will be mated with a service module containing accelerometers, avionics, a low gravity rate control system, and battery packs. This suborbital mission will last approximately 21 minutes, providing at least 13 minutes of microgravity time. The experiments are as follow: study into polymer membrane processes; polymer curing; plasma particle generation; automated generic bioprocessing apparatus; biomodule; thin films; materials dispersion apparatus; foam formation; electrodeposition process; and powdered materials processing.

Ferguson, Bruce W.↗

A review of Space Shuttle payload-bay lift-off flight data and analysis comparisons

The design evolution of Space Shuttle payloads to be launched requires structural analyses and testing, based on Shuttle load environments, to ensure flight safety and mission success. The adequacy of predicted load environments is continually assessed against flight and ground measured data. The Space Shuttle program has utilized extensive flight measurements to assess payload bay environments. As part of the orbital flight test program on STS-1 through STS-5, the orbiter Columbia was equipped with a broad range of instrumentation, including accelerometers and microphone in the payload bay. The orbiter Challenger was equipped with payload bay measurement systems on six of its flights, and the orbiter Discovery was similarly instrumented beginning with STS-26. The payload bay data, along with other measurements recorded on these flights, are compared to design load requirements for payloads, and updates are made as necessary.

Hamilton, David A.↗

RMS active damping augmentation

The topics are presented in viewgraph form and include: RMS active damping augmentation; potential space station assembly benefits to CSI; LaRC/JSC bridge program; control law design process; draper RMS simulator; MIMO acceleration control laws improve damping; potential load reduction benefit; DRS modified to model distributed accelerations; accelerometer location; Space Shuttle aft cockpit simulator; simulated shuttle video displays; SES test goals and objectives; and SES modifications to support RMS active damping augmentation.

Michael G Gilbert↗

Development of a residual acceleration data reduction and dissemination plan

A major obstacle in evaluating the residual acceleration environment in an orbiting space laboratory is the amount of data collected during a given mission: gigabytes of data will be available as SAMS units begin to fly regularly. Investigators taking advantage of the reduced gravity conditions of space should not be overwhelmed by the accelerometer data which describe these conditions. We are therefore developing a data reduction and analysis plan that will allow principal investigators of low-g experiments to create experiment-specific residual acceleration data bases for post-flight analysis. The basic aspects of the plan can also be used to characterize the acceleration environment of earth orbiting laboratories. Our development of the reduction plan is based on the following program of research: the identification of experiment sensitivities by order of magnitude estimates and numerical modelling; evaluation of various signal processing techniques appropriate for the reduction, supplementation, and dissemination of residual acceleration data; and testing and implementation of the plan on existing acceleration data bases. The orientation of the residual acceleration vector with respect to some set of coordinate axes is important for experiments with known directional sensitivity. Orientation information can be obtained from the evaluation of direction cosines. Fourier analysis is commonly used to transform time history data into the frequency domain. Common spectral representations are the amplitude spectrum which gives the average of the components of the time series at each frequency and the power spectral density which indicates the power or energy present in the series per unit frequency interval. The data reduction and analysis scheme developed involves a two tiered structure to: (1) identify experiment characteristics and mission events that can be used to limit the amount of accelerator data an investigator should be interested in; and (2) process the data in a way that will be meaningful to the experiment objectives. A general outline of the plan is given.

Rogers, Melissa J. B.↗

Development of and flight results from the Space Acceleration Measurement System (SAMS)

Described here is the development of and the flight results from the Space Acceleration Measurement System (SAMS) flight units used in the Orbiter middeck, Spacelab module, and the Orbitercargo bay. The SAMS units are general purpose microgravity accelerometers designed to support a variety of science experiments with microgravity acceleration measurements. A total of six flight units have been fabricated; four for use in the Orbiter middeck and Spacelab module, and two for use in the Orbiter cargo bay. The design of the units is briefly described. The initial two flights of SAMS units on STS-40 (June 1991) and STS-43 (August 1991) resulted in 371 megabytes and 2.6 gigabytes of data respectively. Analytical techniques developed to examine this quantity of acceleration data are described and sample plots of analyzed data are illustrated. Future missions for the SAMS units are listed.

Delombard, Richard↗

Spacecraft dynamics characterization and control system failure detection. Volume 3: Control system failure monitoring

We discuss the application of Generalized Parity Relations to two experimental flexible space structures, the NASA Langley Mini-Mast and Marshall Space Flight Center ACES mast. We concentrate on the generation of residuals and make no attempt to implement the Decision Function. It should be clear from the examples that are presented whether it would be possible to detect the failure of a specific component. We derive the equations from Generalized Parity Relations. Two special cases are treated: namely, Single Sensor Parity Relations (SSPR) and Double Sensor Parity Relations (DSPR). Generalized Parity Relations for actuators are also derived. The NASA Langley Mini-Mast and the application of SSPR and DSPR to a set of displacement sensors located at the tip of the Mini-Mast are discussed. The performance of a reduced order model that includes the first five models of the mast is compared to a set of parity relations that was identified on a set of input-output data. Both time domain and frequency domain comparisons are made. The effect of the sampling period and model order on the performance of the Residual Generators are also discussed. Failure detection experiments where the sensor set consisted of two gyros and an accelerometer are presented. The effects of model order and sampling frequency are again illustrated. The detection of actuator failures is discussed. We use Generalized Parity Relations to monitor control system component failures on the ACES mast. An overview is given of the Failure Detection Filter and experimental results are discussed. Conclusions and directions for future research are given.

Vanschalkwyk, Christiaan M.↗

RL-34 ring laser gyro laboratory evaluation for the Deep Space Network antenna application

The overall results of this laboratory evaluation are quite encouraging. The gyro data is in good agreement with the system's overall pointing performance, which is quite close to the technical objectives for the Deep Space Network (DSN) application. The system can be calibrated to the levels required for millidegree levels of pointing performance, and initialization performance is within the required 0.001 degree objective. The blind target acquisition performance is within a factor of two of the 0.0001 degree objective, limited only by a combination of the slow rate (0.5 deg/sec) and the existing production quantization logic (0.38 arc-sec/pulse). Logic circuitry exists to better this performance such that it will better the objective by 50 percent. Representative data with this circuitry has been provided for illustration. Target tracking performance is about twice the one millidegree objective, with several factors contributing. The first factor is the bias stability of the gyros, which is exceptional, but will limit performance to the 0.001 and 0.002 degree range for long tracking periods. The second contributing factor is the accelerometer contributions when the system is elevated. These degrade performance into the 0.003 to 0.004 degree range, which could be improved upon with some additional changes. Finally, we have provided a set of recommendations to improve performance closer to the technical objectives. These recommendations include gyro, electronics, and system configurational changes that form the basis for additional work to achieve the desired performance. In conclusion, we believe that the RL-34 ring laser gyro-based advanced navigation system demonstrated performance consistent with expectations and technical objectives, and it has the potential for even further enhancement for the DSN application.

Source record↗

Improved HIRAP flight calibration technique

A method of removing non-aerodynamic acceleration signals and calibrating the High Resolution Accelerometer Package (HiRAP) has been developed and improved. Twelve HiRAP mission data sets have been analyzed applying the improved in-flight calibration technique. The application of flight calibration factors to the data sets from these missions produced calibrated acceleration levels within +/- 5.7 micro-g of zero during a time in-flight when the acceleration level was known to be less than 1 g. To validate the current in-flight calibration technique, the atmospheric density results, specifically the normal-to-axial density ratios, have been compared with the analysis results obtained with the previous in-flight calibration technique. This comparison shows an improvement (up to 12.4 percent per flight) in the density ratio when the updated in-flight calibration technique is used.

Moats, Christina D.↗

Analysis of Spacelab 3 residual acceleration data

A data reduction plan is being developed to efficiently process residual acceleration data, making such data more accessible to principal investigators of low-gravity experiments. Accelerometer data collected during the Spacelab 3 mission is being processed using a prototype version of this plan. The plan addresses various aspects of acceleration data analysis: the identification of disturbances that are intolerable to experiments, the investigation of acceleration orientations, the definition and characterization of the background acceleration corresponding to a given experiment time line, the isolation and examination of particular significant disturbances, and the identification of disturbance sources. Acceleration magnitude, frequency, and orientation are discussed: transient accelerations can have magnitudes as large as 0.01 g with frequency components no greater than 0.001 g. These accelerations fluctuate rapidly in orientation. The occurrence of disturbance sources in an orbiter is tentatively identified as a random process, whereas the response of the orbiter to given accelerations is considered deterministic. The need to continue monitoring of residual accelerations in orbiting space laboratories is stressed.

Rogers, Melissa J. B.↗

Comprehensive helicopter rotor instrumentation - A retrofit approach using miniature transducers

This paper reports an approach used to retrofit a set of full-scale main rotor blades with 290 miniature pressure transducers, 46 strain gages, and 24 miniature accelerometers. Normally, in order to avoid disturbing the aerodynamics of the rotor flow field, the pressure instrumentation must be integrally built into the body of the rotor blades. However, using a method developed with NASA, miniature pressure transducers are mounted to the blade exterior surface without degrading the quality of the blade aerodynamics. Moreover, it is estimated that this approach reduced costs by more than 50 percent over building a set of pressure instrumented blades. The aerodynamic measurement objectives are presented as are instrumentation design considerations, type of instrumentation used, assembly process, and the installed instrumentation characteristics.

Jacklin, Stephen A.↗

Development of and flight results from the Space Acceleration Measurement System (SAMS)

This paper describes the development of and flight results from the Space Acceleration Measurement System (SAMS) flight units used in the Orbiter middeck, Spacelab module and the Orbiter cargo bay. The SAMS units are general purpose microgravity accelerometers designed to support a variety of science experiments with microgravity acceleration measurements. A total of six flight units have been fabricated; four for use in the Orbiter middeck and Spacelab module, and two for use in the Orbiter cargo bay. The design of the units is briefly described. The initial two flights of SAMS units on STS-40 (June 1991) and STS-43 (August 1991) resulted in 371 megabytes and 2.6 gigabytes of data, respectively. Analytical techniques developed to examine this quantity of acceleration data are described and sample plots of analyzed data are illustrated. Future missions for the SAMS units are listed.

Delombard, Richard↗

The process of control design for the NASA Langley Minimast structure

The design process used to select sensors for feedback and performance weights on the Minimast facility is discussed. Initially, a series of controllers are synthesized using H2 optimal control techniques for the given structural model, a variety of sensor locations and performance criteria to determine the best displacement sensor and/or accelerometers to be used for feedback. Upon selection of the sensors, controllers are formulated to determine the affect of using a reduced-order model of the Minimast structure instead of the higher-order structural analysis model for control design and the relationship between the actuator torque level and the closed-loop performance. Based on this information, controllers are designed using micro-synthesis techniques and implemented on the Minimast structure. Results of the implementation of these controllers on the Minimast experimental facility are presented.

Balas, Gary J.↗

Damping in coupled bending and torsion - An experiment

Traditional experimental modal testing methods are used to determine the damping properties of a Euler-Bernoulli beam with offset inertial tip mass. Both viscous and strain rate damping models are considered in bending and in torsion. A partial differential equation model of the coupled system is used. Eigenfunctions are derived for the coupled system by using a Green's function approach to derive the approximate uncoupled eigenfunctions. These eigenfunctions are used in a decoupled fashion with experimental modal data to estimate the damping parameters of the coupled system. The experimental modal data were obtained from both free and impulse responses using a combined translational and rotational accelerometer.

Umland, Jeffrey W.↗

Residual acceleration data analysis for Spacelab missions

A two-level reduction plan is developed analytically with references to existing experimental data that can be used to develop accelerometer databases for postflight experiment analyses. Residual-acceleration data from previous experiments are studied with attention given to the differences in magnitude among the databases. First-level processing is based on the identification of instances in which tolerable acceleration levels are exceeded so that the time intervals requiring further scrutiny are found. Acceleration time histories including magnitude and orientation are utilized with frequency data for the second level of processing, and the data required for a given time window are reduced by means of data decimation. The identification and processing of limited windows of acceleration data facilitates the characterization of the acceleration environment. These characterizations are of use in the design, location, and utilization of low-gravity laboratory equipment.

Rogers, Melissa J. B.↗

Second-order state estimation experiments using acceleration measurements

The estimation of dynamic states for feedback control of structural systems using second-order differential equations and acceleration measurements is described. The formulation of the observer model, and the design of the observer gains is discussed in detail. It is shown the second-order observer is highly stable because the stability constraints on the observer gains are model independent. The limitation of the proposed observer is the need for 'nearly' collocated actuators and accelerometers. Experimental results using a control-structure interaction testbed are presented that show the second-order observer provided more stability than a Kalman filter estimator without decreasing closed-loop performance.

Belvin, W. K.↗