Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Electrochemical Corrosion of SIMFUEL: Effects of dissolved H2 and noble metal particles

This report describes the results from electrochemical corrosion tests that were conducted using simulated spent fuel (SIMFUEL) materials comprised of UO2 and surrogate fission products. Two SIMFUEL compositions were tested to quantify the effect of noble metal inclusions and dissolved H2 on the UO2 dissolution rate. One material consisted of UO2 with added lanthanide oxides (UO2 N) and the other consisted of UO2 with added lanthanide oxides and noble metals (UO2-H) at concentrations to simulate high burnup fuel. The electrochemical corrosion tests on the SIMFUEL materials were conducted in aqueous electrolyte solutions (pH 10) that were either saturated with air or purged with a H2/Ar gas mixture to maintain a constant dissolved H2 concentration. The results from electrochemical corrosion tests on SIMFUEL can be applied to qualitatively understand and also quantify the separate effects of water chemistry and fuel composition on the degradation behavior of the UO2 matrix. Open circuit potential (OCP) measurements on a SIMFUEL material of known composition (i.e., known fraction of NMPs at the fuel surface) immersed in a known solution chemistry (i.e., pH, Eh, [O2], [H2]) at known temperature provide qualitative insight into the degradation behavior of the UO2 matrix. If the OCP is above the threshold potential at which the oxidative dissolution of U(IV) to U(VI) occurs, the SNF is expected to degrade by oxidative processes under the experimental conditions. The net currents that are measured during potentiostatic tests, during which the surface potential of the SIMFUEL material is fixed by a potentiostat, can be used to quantify the UO2 degradation rate and optimize the rate constant values used in the Fuel Matrix Degradation Model (FMDM) for half reactions that occur on the SNF surface. Specifically, electrochemical measurements enable the estimation of the total anodic current at ECORR–which is the surface potential at which the total anodic and total cathodic currents are equal–so that the rate constant values for key reactions can be calculated. The open circuit potential measurements, potentiostatic tests, surface property measurements (scanning electron microscopy images and electrochemical impedence spectroscopy plots), and solution elemental composition analyses are being performed to update and optimize the FMDM. A case study is presented herein to show how electrochemical corrosion test results and accompanying characterization results for the UO2 N material in air-saturated solution can be used to validate the SNF surface reaction module of the FMDM. Future electrochemical tests will be conducted to provide quantitative information on the effects of NM content (burnup), H2 concentration, water chemistry, temperature, and galvanic couples with cladding and EBS alloys on UO2 degradation that can be used to improve the accuracy and functionality of the FMDM.

Thomas, Sara↗

Intercalation of Mg into a Few-Layer Phyllomanganate in Non-aqueous Electrolytes at Room Temperature

The use of oxide cathodes in Mg batteries would unlock a potential energy storage system that delivers high-energy density. However, poor kinetics of Mg diffusion in known solid oxide lattices strongly limits reversible intercalation, which motivates the sustained exploration of new candidates. Herein, nanocrystals of a few-layer phyllomanganate, reminiscent of the mineral vernadite, were shown to have considerable electrochemical activity toward Mg intercalation at room temperature, where it delivered similar to 190 mAh g- 1 at similar to 1.9 V (vs Mg/Mg 2+ ) in batteries paired with a Mg metal anode. Multimodal characterization confirmed the notable degree of reversible intercalation by probing the structural, compositional, and redox changes undertaken by the oxide. Distinct levels of Mg activity were also observed while varying the content of small amounts of lattice water and the temperature of the reaction. The results reaffirm the prospects for operational Mg batteries using oxide cathode in moderate conditions, overcoming current limits of performance of this prospective technology.

25 ENERGY STORAGE↗

Investigation of Nanoparticle Degradation in Hydrogen Fuel Cell Systems through Automated Electron Microscopy

Proton exchange membrane fuel cells (PEMFC) are promising devices for the deployment of hydrogen-powered heavy-duty vehicles, providing a higher efficiency for similar driving range and fueling time than the existing ones. However, PEMFCs still encounter durability challenges mainly due to catalyst degradation in the cathode. Mitigating these performance losses requires a better understanding of the degradation mechanisms under heavy-duty accelerated stress tests (ASTs) [1]. Scanning transmission electron microscopy (STEM) combined with energy dispersive X-ray spectroscopy (EDS) are key tools for the analysis of Pt and PtCo nanoparticle size, spatial distribution and composition [2]. Electron tomography is also used to determine the rate and type of degradation of catalyst nanoparticles as a function of their position on the carbon support. In this work, automated data acquisition software, paired with a custom Python code, have been used to study the effect of different accelerated stress tests (ASTs) on nanoparticle coarsening [2]. Figure 1 shows high-angle annular dark-field (HAADF)-STEM images and EDS maps comparing the cathodes of membrane electrode assemblies (MEAs) following an electrocatalyst AST performed under H2/N2 with that of the heavy-duty AST performed under H2/air. We will discuss how AST conditions affect considerably the spatial distribution of the nanoparticles across the electrode between the membrane and microporous layer. Although the median particle size increased more in the MEA aged under the heavy-duty AST, as determined using a high-throughput image analysis, the quantitative EDS measurements demonstrate that the electrocatalyst AST resulted in more Pt and Co dissolution from the cathode, which is another important indicator of electrocatalyst degradation. We will further present the impact of the relative humidity (% RH) on the degradation mechanisms demonstrated using the same approach. Electron tomography has been used to distinguish the Pt nanoparticles residing on the carbon support surface (exterior) from those within the pore structure (interior) in order to determine the relative stability of interior and exterior nanoparticles. As shown in Figure 2, we will compare the Pt catalyst particle size at the beginning of test (BOT) and end of test (EOT), and discuss the importance of automating the electron tomography workflow, i.e. acquisition, reconstruction, and visualization, to increase sampling and determine the standard deviation of these measurement. The outlook for utilizing low-dose cryo-tomography for limiting damage to the catalyst, support, and especially proton-conducting ionomer will also be discussed [3].

Amichi, Lynda↗

Intercalation of Ca into a Highly Defective Manganese Oxide at Room Temperature

The utilization of oxide frameworks as intercalation cathodes for non-aqueous Ca-ion batteries potentially unlocks a new energy storage system that delivers high energy density. However, the slow kinetics of Ca 2+ in oxide electrodes strongly handicaps their activity and reversibility at room temperature. Here, nanocrystals of layered MnO x containing a high concentration of atomic defects and lattice water are shown to have remarkable electrochemical activity towards Ca 2+ , amounting to a capacity of ~130 mAh/g at room temperature. Multimodal characterization revealed the notable degree of intercalation by probing the structural, compositional and redox changes undertaken by the defective MnO x nanocrystals. The results suggest that the existence of atomic defects and lattice water played a role in improving Ca 2+ diffusivity in the oxide. These outcomes reaffirm the prospects for functional Ca-ion batteries using oxide cathodes under moderate conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of MWCNT on prepared cathode material (Li{sub 2}Mn{sub (x)}Fe{sub (1-x)}SiO{sub 4}) for energy storage applications

The electrode material Li{sub 2}MnFeSiO{sub 4} was successfully synthesized by standard sol–gel method and further modified with multiwalled carbon nano tube (MWCNT) to achieve better electrochemical properties. Our strategy helps us to improve the performance and storage capacity as compared with the bared material. This novel composite structure constructs an efficient cation (Li{sup +}) and electron channel which significantly enhance the Li{sup +} ion diffusion coefficient and reduced charge transfer resistance. Hence leads to high conductivity and specific capacity. Characterization technique like Field emission scanning electron microscopy (FESEM) has been used to confirm its morphology, structure and particle size which comes out to be of the order of ∼20 to 30 nm. Lesser particle size reveals better electrochemical properties. Electrical conductivity (∼10{sup −5} Scm{sup −1}) of MWCNT doped oxide cathode materials was recorded using ac impedance spectroscopy technique which reflects tenfold increment when compared with pure oxide cathode materials. Cyclic voltametery analysis has been done to calculate specific capacity and potential window of materials with and without CNTs. The results obtained from different techniques are well correlated and suitable for energy storage applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Direction of CRT waste glass processing: Electronics recycling industry communication

Highlights: Black-Right-Pointing-Pointer Given a large flow rate of CRT glass {approx}10% of the panel glass stream will be leaded. Black-Right-Pointing-Pointer The supply of CRT waste glass exceeded demand in 2009. Black-Right-Pointing-Pointer Recyclers should use UV-light to detect lead oxide during the separation process. Black-Right-Pointing-Pointer Recycling market analysis techniques and results are given for CRT glass. Black-Right-Pointing-Pointer Academic initiatives and the necessary expansion of novel product markets are discussed. - Abstract: Cathode Ray Tube, CRT, waste glass recycling has plagued glass manufacturers, electronics recyclers and electronics waste policy makers for decades because the total supply of waste glass exceeds demand, and the formulations of CRT glass are ill suited for most reuse options. The solutions are to separate the undesirable components (e.g. lead oxide) in the waste and create demand for new products. Achieving this is no simple feat, however, as there are many obstacles: limited knowledge of waste glass composition; limited automation in the recycling process; transportation of recycled material; and a weak and underdeveloped market. Thus one of the main goals of this paper is to advise electronic glass recyclers on how to best manage a diverse supply of glass waste and successfully market to end users. Further, this paper offers future directions for academic and industry research. To develop the recommendations offered here, a combination of approaches were used: (1) a thorough study of historic trends in CRT glass chemistry; (2) bulk glass collection and analysis of cullet from a large-scale glass recycler; (3) conversations with industry members and a review of potential applications; and (4) evaluation of the economic viability of specific uses for recycled CRT glass. If academia and industry can solve these problems (for example by creating a database of composition organized by manufacturer and glass source) then the reuse of CRT glass can be increased.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

La 0.9-x Ca x Ce 0.1 CrO 3-δ as potential anode materials for solid oxide fuel cells

LaCrO3 doped with calcium and cerium on the A-site in the series of La0.9-xCaxCe0.1CrO3-δ (LCCC3060, LCCC4050, LCCC5040, LCCC6030 corresponding to x = 0.6, 0.5, 0.4, and 0.3 respectively), is synthesized by a sol–gel combustion method and evaluated as anode material for solid oxide fuel cells (SOFCs). Relatively higher Ca-doping on La in LaCrO3 is found to improve both electronic and ionic conductivity. LCCC compositions have demonstrated good chemical stability in reducing atmospheres. Evaluation of the LCCC material as anode in symmetrical cell configuration shows that the highest Ca-doping composition results in the lowest activation energy and the lowest polarization resistance. La0.8Sr0.2Ga0.83Mg0.17O3-δ (LSGM) electrolyte-supported single cells with LCCC3060 as the anode and La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) as the cathode show that LCCC3060 can be a potential anode material for H2, but not for CH4.

25 ENERGY STORAGE↗

Temperature Dependence of Aliovalent-vanadium Doping in LiFePO4 Cathodes

Vanadium-doped olivine LiFePO4 cathode materials have been synthesized by a novel low-temperature microwave-assisted solvothermal (MW-ST) method at 300 oC. Based on chemical and powder neutron/X-ray diffraction analysis, the compositions of the synthesized materials were found to be LiFe1-3x/2Vx x/2PO4 (0 x 0.2) with the presence of a small number of lithium vacancies charge-compensated by V4+, not Fe3+, leading to an average oxidation state of ~ 3.2+ for vanadium. Heating the pristine 15 % V-doped sample in inert or reducing atmospheres led to a loss of vanadium from the olivine lattice with the concomitant formation of a Li3V2(PO4)3 impurity phase; after phase segregation, a partially V-doped olivine phase remained. For comparison, V-doped samples were also synthesized by conventional ball milling and heating, but only ~ 10 % V could be accommodated in the olivine lattice in agreement with previous studies. The higher degree of doping realized with the MW-ST samples demonstrates the temperature dependence of the aliovalent-vanadium doping in LiFePO4.

Harrison, Katharine L↗

CoP as an Acid-Stable Active Electrocatalyst for the Hydrogen-Evolution Reaction: Electrochemical Synthesis, Interfacial Characterization and Performance Evaluation

Films of CoP have been electrochemically synthesized, characterized, and evaluated for performance as a catalyst for the hydrogen-evolution reaction (HER). The film was synthesized by cathodic deposition from a boric acid solution of Co 2+ and H 2 PO 2 – on copper substrates followed by operando remediation of exogenous contaminants. The films were characterized structurally and compositionally by scanning-electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and Raman spectrophotometry. The catalytic activity was evaluated by cyclic voltammetry and chronopotentiometry. Surface characterization prior to electrocatalysis indicated that the film consisted of micrometer-sized spherical clusters located randomly and loosely on a slightly roughened surface. The composition of both the clusters and surface consisted of cobalt in the metallic, phosphide, and amorphous-oxide forms (CoO·Co 2 O 3 ) and of phosphorus as phosphide and orthophosphate. The orthophosphate species, produced by air-oxidation, were eliminated upon HER electrocatalysis in sulfuric acid. The operando film purification yielded a functional electrocatalyst with a Co:P stoichiometric ratio of 1:1. After the HER, the surface was densely packed with micrometer-sized, mesa-like particles whose tops were flat and smooth. The CoP eletrodeposit exhibited an 85 mV overvoltage (η) for the HER at a current density of 10 mA cm –2 and was stable under operation in highly acidic solution, with an increase in η of 18 mV after 24 h of continuous operation. In conclusion, the comparative HER catalytic performance of CoP, film or nanoparticles, is as follows: ηPt < ηCoP film = ηCoP NP, ηNi 2 P < ηCoSe 2 < ηMoS 2 < ηMoSe 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding the critical chemistry to inhibit lithium consumption in lean lithium metal composite anodes

Lithium metal has been deemed by many as the “Holy Grail” of anode materials due to its high theoretical capacity (~3860 mA h g -1 ), redox potential of -3.040 V vs. SHE, and light weight. The goal of this work is to investigate the relationship between a lean lithium metal anode and its consumption as a function of host materials, electrochemical protocol and electrolyte composition. With the use of carbon nanofibers, lithium metal has been electrodeposited onto the host matrix and used in a battery with a LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode. The mass-loading of lithium can be easily controlled and utilized to investigate the practicality of an anode limited battery (i.e., limited lithium with an effective thickness <15 μm) in a high surface area matrix. We then quantify the consumption rate of active lithium using different electrolyte additives and current rates in full cells and observe that the lithium consumption behavior in an anode-limited cell is different from that in an anode-excess cell. Our results highlight the necessity of applying truly lithium-limited cells when evaluating the electrochemical properties of lithium anodes and electrolyte additives. By extending this method to a standard graphite host, full cells can retain 75% of their initial capacities after 1000 cycles. The present study demonstrates the importance of graphitic carbon in increasing the lifespan of limited lithium (<15 μm) for practical lithium metal batteries.

25 ENERGY STORAGE↗

First field test of a novel optical gas analyser in the exhaust of Wendelstein 7-X

A novel optical gas analyser, designed for isotope-resolved exhaust composition measurement, was field-tested at Wendelstein 7-X (W7-X) to validate its laboratory-proven concept under operational fusion experiment conditions. The system, Optix, comprises a cold cathode remote plasma generator and a high-resolution Fabry–Perot spectrometer and was deployed in the exhaust line of W7-X during the OP2.3 campaign. The injection of 3 He and 4 He for minority ion-cyclotron heating provided a test case for helium isotope discrimination. Despite limitations due to background gas and low partial pressures of the target species, isotope-resolved spectral signatures were successfully observed, demonstrating the fundamental viability of the Optix approach. Additionally, the spectrometer was evaluated for plasma emission measurements from both core and edge sightlines. While helium line emission was detectable, interpretation was hindered by complex background signals, highlighting the benefits of controlled remote plasma generators for spectroscopy. This first deployment provides critical insight into pressure requirements, spectral resolution, and operational constraints, informing future applications of optical exhaust diagnostics in fusion devices.

magnetic confinement fusion↗

Apollo scientific experiments data handbook

A brief description of each of the Apollo scientific experiments was described, together with its operational history, the data content and formats, and the availability of the data. The lunar surface experiments described are the passive seismic, active seismic, lunar surface magnetometer, solar wind spectrometer, suprathermal ion detector, heat flow, charged particle, cold cathode gage, lunar geology, laser ranging retroreflector, cosmic ray detector, lunar portable magnetometer, traverse gravimeter, soil mechanics, far UV camera (lunar surface), lunar ejecta and meteorites, surface electrical properties, lunar atmospheric composition, lunar surface gravimeter, lunar seismic profiling, neutron flux, and dust detector. The orbital experiments described are the gamma-ray spectrometer, X-ray fluorescence, alpha-particle spectrometer, S-band transponder, mass spectrometer, far UV spectrometer, bistatic radar, IR scanning radiometer, particle shadows, magnetometer, lunar sounder, and laser altimeter. A brief listing of the mapping products available and information on the sample program were also included.

Eichelman, W. F.↗

The indirect electrochemical refining of lunar ores

Recent work performed on an electrolytic cell is reported which addresses the implicit limitations in various approaches to refining lunar ores. The cell uses an oxygen vacancy conducting stabilized zirconia solid electrolyte to effect separation between a molten salt catholyte compartment where alkali metals are deposited, and an oxygen-evolving anode of composition La(0.89)Sr(0.1)MnO3. The cell configuration is shown and discussed along with a polarization curve and a steady-state current-voltage curve. In a practical cell, cathodically deposited liquid lithium would be continuously removed from the electrolytic cell and used as a valuable reducing agent for ore refining under lunar conditions. Oxygen would be indirectly electrochemically extracted from lunar ores for breathing purposes.

Semkow, Krystyna W.↗

Pitch Carbon-coated Ultrasmall Si Nanoparticle Lithium-ion Battery Anodes Exhibiting Reduced Reactivity with Carbonate-based Electrolyte

Silicon anodes for lithium-ion batteries (LIBs) have the potential for higher energy density compared to conventionally used graphite-based LIB anodes. However, silicon anodes exhibit poor cycle and calendar lifetimes due to mechanical instabilities and high chemical and electrochemical reactivity with the carbonate-based electrolytes that are typically used in LIBs. In this work, we synthesize a pitch carbon-coated silicon nanoparticle composite active material for LIB anodes that exhibits reduced chemical reactivity with carbonate-based electrolytes compared to an uncoated silicon anode. Silicon primary particle sizes less than 10 nm diameter minimize micro-scale mechanical degradation of the anode composite, while conformal coatings of pitch carbon minimize the parasitic reactions between the silicon and the electrolyte. When matched with a high voltage NMC622 (LiNi 0.6 Mn 0.2 Co 0.2 O 2 ) cathode, the pitch carbon-coated silicon anode retains approximately 75% of its initial capacity at the end of 1000 cycles. Increasing the areal loading of the pitch carbon-coated silicon anodes to realize energy density improvements over graphite anodes results in severe mechanical degradation on the electrode level, highlighting a remaining challenge to be addressed in future work.

25 ENERGY STORAGE↗

Electrochemical performance investigations on the hydrogen depolarized CO2 concentrator

An extensive investigation of anode and cathode polarization in complete cells and half cells was conducted to determine the factors affecting HDC electrode polarization and the nature of this polarization. Matrix-electrolyte-electrode interactions and cell electrolyte composition were also investigated. The electrodes were found to have normal performance capabilities. The HDC anode polarization characteristics were correlated with a theoretical kinetic analysis; and, except for some quantitative details, a rather complete understanding of the causes for HDC electrode polarization was formulated. One of the important finding resulting from the kinetic analysis was that platinum appears to catalyze the decomposition of carbonic acid to carbon dioxide and water. It was concluded that the abnormal voltage performance of the One Man ARS HDC cells was caused by insufficient cell electrolyte volume under normal operating conditions due to deficiencies in the reservoir to cell interfacing.

Aylward, J. R.↗

Ion beam enhancement in magnetically insulated ion diodes for high-intensity pulsed ion beam generation in non-relativistic mode

High-intensity pulsed ion beam (HIPIB) with ion current density above Child-Langmuir limit is achieved by extracting ion beam from anode plasma of ion diodes with suppressing electron flow under magnetic field insulation. It was theoretically estimated that with increasing the magnetic field, a maximal value of ion current density may reach nearly 3 times that of Child-Langmuir limit in a non-relativistic mode and close to 6 times in a highly relativistic mode. In this study, the behavior of ion beam enhancement by magnetic insulation is systematically investigated in three types of magnetically insulated ion diodes (MIDs) with passive anode, taking into account the anode plasma generation process on the anode surface. A maximal enhancement factor higher than 6 over the Child-Langmuir limit can be obtained in the non-relativistic mode with accelerating voltage of 200–300 kV. The MIDs differ in two anode plasma formation mechanisms, i.e., surface flashover of a dielectric coating on the anode and explosive emission of electrons from the anode, as well as in two insulation modes of external-magnetic field and self-magnetic field with either non-closed or closed drift of electrons in the anode-cathode (A-K) gap, respectively. Combined with ion current density measurement, energy density characterization is employed to resolve the spatial distribution of energy density before focusing for exploring the ion beam generation process. Consistent results are obtained on three types of MIDs concerning control of neutralizing electron flows for the space charge of ions where the high ion beam enhancement is determined by effective electron neutralization in the A-K gap, while the HIPIB composition of different ion species downstream from the diode may be considerably affected by the ion beam neutralization during propagation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modeling ammonia-fueled co-flow dual-channel protonic-ceramic fuel cells

This paper reports the model development for a dual-channel protonic-ceramic fuel cell (PCFC) operating on ammonia fuel. The model considers the coupled interactions of several physical and chemical processes, including three-dimensional heat conduction within the bipolar plates and the membrane-electrode assembly (MEA), one-dimensional flow within the fuel and air channels, detailed heterogeneous catalytic reactions within the porous composite anode structure, Butler–Volmer representation of the charge-transfer chemistry, and Nernst–Planck transport of three charged defects (protons, oxygen vacancies, and small polarons) within the dense electrolyte membrane. The membrane-electrode assembly is composed of a Ni-BCZYYb (BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3-δ ) anode, a BCZYYb electrolyte membrane, and a BCFZY (BaCo 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3-δ ) cathode. Chemical and physical parameters for the MEA model are established using previously published button-cell data. One aspect of the study is to investigate the partial ammonia decomposition upstream of the fuel cell. Such fuel cracking increases the H 2 content of the fuel entering the PCFC, which may have benefits. However, endothermic ammonia pyrolysis within the composite anode structure assists with thermal control of the cell. The dual-channel model can be considered as the unit cell of a full fuel-cell stack.

25 ENERGY STORAGE↗