Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Quantifying Reaction and Rate Heterogeneity in Battery Electrodes in 3D through Operando X-ray Diffraction Computed Tomography

In composite battery electrode architectures, local limitations in ionic and electronic transport can result in nonuniform energy storage reactions. Understanding such reaction heterogeneity is important to optimizing battery performance, including rate capability and mitigating degradation and failure. Here, we use spatially resolved X-ray diffraction computed tomography to map the reaction in a composite electrode based on the LiFePO 4 active material as it undergoes charge and discharge. Accelerated reactions at the electrode faces in contact with either the separator or the current collector demonstrate that both ionic and electronic transport limit the reaction progress. The data quantify how nonuniformity of the electrode reaction leads to variability in the charge/discharge rate, both as a function of time and position within the electrode architecture. Importantly, this local variation in the reaction rate means that the maximum rate that individual cathode particles experience can be substantially higher than the average, control charge/discharge rate, by a factor of at least 2-5 times. As a result, this rate heterogeneity may accelerate rate-dependent degradation pathways in regions of the composite electrode experiencing faster-than-average reaction and has important implications for understanding and optimizing rate-dependent battery performance. Benchmarking multiscale continuum model parameters against the observed reaction heterogeneity permits extension of these models to other electrode geometries.

25 ENERGY STORAGE↗

Experimental Investigation of Microstructure and Phase Transitions in Ag-Cu-Zn Brazing Alloys

Microstructure and phase transitions of selected brazing alloys from the Ag-Cu-Zn ternary system were investigated. Four ternary alloys with silver content in the compositional range from 25 to 60 wt.% were studied using x-ray diffraction (XRD) and scanning electron microscopy coupled with the energy-dispersive spectroscopy (SEM–EDS). Phase transitions of the investigated alloys were measured using differential scanning calorimetry (DSC). Experimentally obtained results were compared with the results of a thermodynamic calculation of the phase equilibria according to the CALPHAD method. The experiments confirmed the optimized thermodynamic parameters for the calculations from the thermodynamic assessment in literature. Phase compositions, liquidus and solidus temperatures were confirmed by the EDS and DTA methods. Additionally, the calculated solidification paths and predicted phase transformations were in agreement with the SEM images.

36 MATERIALS SCIENCE↗

Impact Sensitivity and Ignition Mechanisms of Nanoaluminum-poly(perfluorinated methacrylate) Nanocomposites

Nanoenergetic composites are of overwhelming interest to the Department of Defense because of the higher power output and the ability to finely tune the ignition thresholds of these composites. Recently, several variants of a nanoaluminum-poly(perfluorinated methacrylate) (AlFA) have been synthesized and optimized for a variety of applications including reactive warhead liners and bullet spotters. While conventional techniques such as thermal analysis and bomb calorimetry can be used to characterize the reaction mechanism and energy output of AlFA composites, characterizing their dynamic behaviour is more challenging. Bullet spotter applications require a material to be impact sensitive at very low velocities, yet be adequately insensitive. Several live-fire tests were conducted which revealed the AlFA 50 material reacted consistently upon target impact at high velocities, but unreliably at very low velocities. In an effort to better understand the fundamental impact ignition mechanism and to determine the impact velocity threshold of AlFA 50 a series of Taylor gas gun experiments were conducted. It was determined that the light-initiation mechanism was consistent with a pinch mechanism, and that the ignition velocity threshold was near 74 m/s. Based on these results, it was hypothesized that the addition of a filler material could be used to sensitize the AlFA 50 , and that Asay shear impact testing could be used to determine a more optimal shape of such inclusions. Experiments performed using the Asay shear impact test setup confirmed the pinch ignition mechanism, but observations also revealed that the size of the pinch point was important. It was shown that the addition of large glass beads (> 1mm in diameter) was effective at sensitizing the AlFA 50 material at high and low velocities, with ignition observed at impact velocities as low as 35 m/s.

36 MATERIALS SCIENCE↗

Building wet planets through high-pressure magma–hydrogen reactions

Close-in transiting sub-Neptunes are abundant in our Galaxy. Planetary interior models based on their observed radius–mass relationship suggest that sub-Neptunes contain a discernible amount of either hydrogen (dry planets) or water (wet planets) blanketing a core composed of rocks and metal. Water-rich sub-Neptunes have been believed to form farther from the star and then migrate inwards to their present orbits. Here we report experimental evidence of reactions between warm, dense hydrogen fluid and silicate melt that release silicon from the magma to form alloys and hydrides at high pressures. We found that oxygen liberated from the silicate melt reacts with hydrogen, producing an appreciable amount of water up to a few tens of weight per cent, which is much greater than previously predicted based on low-pressure ideal gas extrapolation. Consequently, these reactions can generate a spectrum of water contents in hydrogen-rich planets, with the potential to reach water-rich compositions for some sub-Neptunes, implying an evolutionary relationship between hydrogen-rich and water-rich planets. Therefore, detection of a large amount of water in exoplanet atmospheres may not be the optimal evidence for planet migration in the protoplanetary disk, calling into question the assumed link between composition and planet formation location.

Horn, H. W. [Arizona State University, Tempe, AZ (↗

In Situ Foaming of Porous (La 0.6 Sr 0.4 ) 0.98 (Co 0.2 Fe 0.8 ) O 3-δ (LSCF) Cathodes for Solid Oxide Fuel Cell Applications

A binder system containing polyurethane precursors was used to in situ foam (direct foam) a (La{sub 0.6}Sr{sub 0.4}){sub 0.98} (Co{sub 0.2} Fe{sub 0.8}) O{sub 3-{ delta}} (LSCF) composition for solid oxide fuel cell (SOFC) cathode applications. The relation between in situ foaming parameters on the final microstructure and electrochemical properties was characterized by microscopy and electrochemical impedance spectroscopy (EIS), respectively. The optimal porous cathode architecture was formed with a 70 vol% solids loading within a polymer precursor composition with a volume ratio of 8:4:1 (isocyanate: PEG: surfactant) in a terpineol-based ink vehicle. The resultant microstructure displayed a broad pore size distribution with highly elongated pore structure.

30 DIRECT ENERGY CONVERSION↗

Simultaneous “Clean-and-Repair” of Surfaces Using Smart Droplets

An autonomous self-healing system, inspired by transportation processes inherent to biology, is described for materials transportation and repair. The selected model system combines inorganic nanoparticles (NPs) on damaged substrates with functional emulsion droplets that pick up the particles from pristine portions of the substrate and deposit them into damaged regions. The droplets are stabilized by polymer surfactants containing phosphorylcholine groups, a polymer composition selected to impart surfactant properties for droplet stabilization as well as fouling resistance to prevent irreversible droplet adsorption on the substrates. Both the NP pickup (cleaning) and drop off (repair) steps are conducted in a system driven by an imposed flow and characterized by fluorescence microscopy. To evaluate and optimize the efficiency of this NP transportation process, the effect of both the chemical composition of the polymer surfactant and the NP surface chemistry is investigated in this work. Interfacial interactions proved enabling for these NP transportation processes, specifically those involving NP/droplet, NP/substrate, and droplet/substrate interactions. Ultimately, droplets capable of both picking up and dropping off NPs are realized by adjusting fluid/fluid and fluid/substrate interactions, with electrostatic interactions between NPs and droplets proving most effective.

36 MATERIALS SCIENCE↗

Rapid Carbon Fiber Prepreg Molding Technology for Automobile Structural Parts - "SEAHAWKS"

Carbon fiber reinforced plastics (CFRP) offer a variety of potential benefits to automotive parts vs. metals, mainly in the form of light-weighting, part consolidation, and corrosion resistance. However, complexities of composite manufacturing and lack of robust supply chain evolution and integration have hindered technological advancements to overcome high manufacturing costs, slow production rates and prolonged time to market. As a result, the use of CFRP in automotive structural parts has been limited to expensive “low to medium” volume platforms. The project overall investigates a concept of ecosystem-based composite manufacturing that enables rapid implementation of an integrated manufacturing system. Through partnering with individual organizations in the prepreg supply chain along with their respective technological advancements in materials, part designs, tool, equipment, recycling and repair, this project’s objective is to integrate these technologies into a manufacturing system through optimizing them individually and as a whole. Upon a successful delivery of a finished composite component to market, all associated technologies are evolved to production readiness levels not only individually but also in part of the integrated manufacturing system itself. Risks are mitigated effectively, as development costs and successes (and/or failures) are shared among all organizations. As a result, further cost reduction of the finished component is anticipated. Toray Composites (America) Inc. led the effort along with 13 other organizations to investigate and validate the concept. Phase I of this project via flat panel demonstrations focused on molding aspects of the integrated manufacturing system from several combinations of prepreg materials and molding methods used such as hydraulic press, RapidClave®, heated composite light tool (HCLT), light induction tool (LIT) and Quickstep. Other aspects such as automation equipment, recycling and component identification to further investigate and validate the concept via component demonstration in Phase II were also explored. It was found that several prepreg/process combinations could achieve a 3-6 min cure cycle time with panel thickness from 0.8 to 2.4 mm. This can be achieved under compaction pressure as low as vacuum, leading to composite panels that are void free, have good to excellent molded surfaces, Tg (by G’onset of DMA) ranging from 120-190 °C, and mechanical performance comparable to conventional autoclave cure.

36 MATERIALS SCIENCE↗

Active learning of ternary alloy structures and energies

Abstract Machine learning models with uncertainty quantification have recently emerged as attractive tools to accelerate the navigation of catalyst design spaces in a data-efficient manner. Here, we combine active learning with a dropout graph convolutional network (dGCN) as a surrogate model to explore the complex materials space of high-entropy alloys (HEAs). We train the dGCN on the formation energies of disordered binary alloy structures in the Pd-Pt-Sn ternary alloy system and improve predictions on ternary structures by performing reduced optimization of the formation free energy, the target property that determines HEA stability, over ensembles of ternary structures constructed based on two coordinate systems: (a) a physics-informed ternary composition space, and (b) data-driven coordinates discovered by the Diffusion Maps manifold learning scheme. Both reduced optimization techniques improve predictions of the formation free energy in the ternary alloy space with a significantly reduced number of DFT calculations compared to a high-fidelity model. The physics-based scheme converges to the target property in a manner akin to a depth-first strategy, whereas the data-driven scheme appears more akin to a breadth-first approach. Both sampling schemes, coupled with our acquisition function, successfully exploit a database of DFT-calculated binary alloy structures and energies, augmented with a relatively small number of ternary alloy calculations, to identify stable ternary HEA compositions and structures. This generalized framework can be extended to incorporate more complex bulk and surface structural motifs, and the results demonstrate that significant dimensionality reduction is possible in thermodynamic sampling problems when suitable active learning schemes are employed.

Chemistry↗

Solvent-Mediated Synthesis of Amorphous Li 3 PS 4 /Polyethylene Oxide Composite Solid Electrolytes with High Li + Conductivity

Solvent-mediated routes have emerged as an effective, scalable, and low-temperature method to fabricate sulfide-based solid-state electrolytes. However, tuning the synthesis conditions to optimize the electrolyte’s morphology, structure, and electrochemical properties is still underexplored. Here, we report a new class of composite solid electrolytes (SEs) containing amorphous Li 3 PS 4 synthesized in situ with a poly(ethylene oxide) (PEO) binder using a one-pot, solvent-mediated route. The solvent and thermal processing conditions have a dramatic impact on the Li 3 PS 4 structure. Conducting the synthesis in tetrahydrofuran resulted in crystalline β-Li 3 PS 4 whereas acetonitrile led to amorphous Li 3 PS 4 . Annealing at 140 °C increased the Li + conductivity of an amorphous composite (Li 3 PS 4 + 1 wt % PEO) by 3 orders of magnitude (e.g., from 4.5 × 10 –9 to 8.4 × 10 –6 S/cm at room temperature) because of: (i) removal of coordinated solvent and (ii) rearrangement of the polyanionic network to form P 2 S 7 4– and PS 4 3– moieties. The PEO content in these composites should be limited to 1–5 wt % to ensure reasonable Li+ conductivity (e.g., up to 1.1 × 10 –4 S/cm at 80 °C) while providing enough binder to facilitate scalable processing. Here, the results of this study highlight a new strategy to suppress crystallization in sulfide-based SEs, which has important implications for solid-state batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A multiscale microstructural approach to ductile-phase toughened tungsten for plasma-facing materials

Increasing fracture toughness and decreasing the ductile-brittle transition temperature of a tungsten-alloy has been shown to be feasible by ductile-phase toughening of tungsten. In this method, a ductile phase is included in a brittle tungsten matrix to prevent fracture propagation by crack bridging or crack deflection. This paper models the deformation behavior of ductile phase toughened tungsten materials such as tungsten-copper composites using a multiscale modeling approach that involves a microstructural dual-phase (copper-tungsten) region of interest where the constituent phases are finely discretized and are described by a continuum damage mechanics model. Large deformation, damage and fracture are allowed to occur and are modeled in this region that is connected to the adjacent homogenized elastic regions to form a macroscopic structure such as a test specimen. This paper illustrates such a multiscale modeling approach to analyze un-notched and single-edge notched (SENB) tungsten-copper composite specimens subjected to three-point bending. The predicted load-displacement responses and crack propagation patterns are compared to the corresponding experimental results to validate the model.

Nguyen, Ba Nghiep↗

Understanding Atom Probe Tomography of Oxide-Supported Metal Nanoparticles by Correlation with Atomic Resolution Electron Microscopy and Field Evaporation Simulation

Metal-dielectric composite materials, specifically metal nanoparticles supported on or embedded in metal oxides, are widely used in catalysis. The accurate optimization of such nanostructures warrants the need for detailed three-dimensional characterization. Atom probe tomography is uniquely capable of generating sub-nanometer structural and compositional data with part-per-million mass sensitivity, but there are reconstruction artifacts for composites containing materials with strongly differing fields of evaporation, as for oxide-supported metal nanoparticles. By correlating atom probe tomography with scanning transmission electron microscopy for Au nanoparticles embedded in an MgO support, deviations from an ideal topography during evaporation are demonstrated directly, and correlated with compositional errors in the reconstructed data. Finite element simulations of the field evaporation process confirm that protruding Au nanoparticles will evolve on the tip surface, and that evaporation field variations lead to an inaccurate assessment of the local composition, effectively lowering the spatial resolution of the final reconstructed dataset. Cross-correlating the experimental data with simulations results in a more detailed understanding of local evaporation aberrations during APT analysis of metal-oxide composites, paving the way towards a more accurate three-dimensional characterization of this technologically important class of materials.

Environmental Molecular Sciences Laboratory↗

Machine-learning-guided descriptor selection for predicting corrosion resistance in multi-principal element alloys

More than $270 billion is spent on combatting corrosion annually in the USA alone. As such, we present a machine-learning (ML) approach to down select corrosion-resistant alloys. Our focus is on a non-traditional class of alloys called multi-principal element alloys (MPEAs). Given the vast search space due to the variety of compositions and descriptors to be considered, and based upon existing corrosion data for MPEAs, we demonstrate descriptor optimization to predict corrosion resistance of any given MPEA. Our ML model with descriptor optimization predicts the corrosion resistance of a given MPEA in the presence of an aqueous environment by down selecting two environmental descriptors (pH of the medium and halide concentration), one chemical composition descriptor (atomic % of element with minimum reduction potential), and two atomic descriptors (difference in lattice constant (Δa) and average reduction potential). Our findings show that, while it is possible to down select corrosion-resistant MPEAs by using ML from a large search space, a larger dataset and higher quality data are needed to accurately predict the corrosion rate of MPEAs. This study shows both the promise and the perils of ML when applied to a complex chemical phenomenon like corrosion of alloys.

36 MATERIALS SCIENCE↗

Au x Pd (300‐ x ) Alloy Nanoparticles for the Oxygen Reduction Reaction in Alkaline Media

Abstract Au x Pd (300‐ x ) nanoalloys were prepared using a dendrimer‐templating method and their electrocatalytic efficiencies towards the oxygen reduction reaction (ORR) were analyzed in alkaline media. The composition‐dependent PdO x reduction potentials of the Au x Pd (300‐ x ) nanoalloys were correlated to the oxygen‐binding (O‐binding) energy of the catalysts. Multiple PdO x reduction peaks were present for the Au 150 Pd 150 and Au 50 Pd 250 catalysts. These peaks were assigned to the alloyed and bulk‐like Pd active sites on the alloyed surface. The results described here are significant because modulation of the O‐binding energies improved the ORR activity on the nanoalloys. Specifically, a linear trend in O‐binding energies of Au x Pd (300‐ x ) dendrimers (DENs) as a function of Pd composition resulted in a volcano‐shaped trend in ORR activity. The optimal O‐binding energy of Au 50 Pd 250 resulted in an approximate 89 mV shift in PdO x reduction relative to Pd 300 and a shift of approximately 76 mV in ORR peak potential.

Trindell, Jamie A.↗

Transient-Liquid-Phase Bonding of H230 Ni-Based Alloy Using Ni-P Interlayer: Microstructure and Mechanical Properties

Transient-liquid-phase bonding using Ni-P as an interlayer has been developed for H230 Ni-Cr-W solid-solution-strengthened Ni-based alloy. Two process parameters—composition of the interlayer and bonding time—have been varied to optimize the mechanical properties. H230 has been bonded into two sets of stacks (set I and II) for 8 and 4 hours using Ni-12P and Ni-6P interlayer, respectively, (wt pct) at 1423 K (1150 °C) and 12.7 MPa. The microstructure of both the stacks has three distinct regions—the joint centerline which showed the presence of pores, an isothermally solidified zone (ISZ) which did not have any carbide precipitates and base H230. Transmission electron microscopy and atom probe tomography showed a uniform microstructure, and an absence of any deleterious phases at the joint and in ISZ. Set I and set II had a yield strength of 76 and 86 pct of that of the H230 sheet, tested at 1023 K (750 °C). Here, the measured elongation at fracture was negligible, but the fracture surfaces revealed a ductile cup-and-cone-type fracture occurring through the ISZ/joint region. Examination of broken tensile samples revealed that the plastic strain was constrained to within one joint region through which fracture occurred.

14 SOLAR ENERGY↗

On Development and Wear Behavior of Microwave-Processed Functionally Graded Ni-SiC Clads on SS-304 Substrate

In this study, the functionally graded Ni-SiC claddings with gradual change in SiC contents were deposited on SS-304 substrate using microwave hybrid heating technique. Experimental trials were carried out inside a multimode domestic microwave device at 2.45 GHz and 900 W. The optimal exposure time of 900 W microwave power was varied with compositional gradient, and it was from 300 to 360 s. The developed functionally graded clad (FGC) was characterized by SEM/EDS, XRD and Vicker’s micro-hardness. Microstructural analysis results revealed that the FGC of approximately 2 mm thickness was developed and was free from any type of interfacial cracks and visible porosity. The maximum micro-hardness was at the top FGC layer, and its value was 1025 ± 30 HV. Three types of single-layer claddings were also developed to compare the tribological behavior of FGC. FGC exhibited 32 and 1.2 times more wear resistance than SS-304 substrate and Ni + 30% SiC layer, respectively. In the case of FGC, wear mainly occurs due to debonding of carbide particles from the matrix, while plastic deformation and strong abrasion are responsible for material loss in the case of the SS-304 substrate.

36 MATERIALS SCIENCE↗

Computational Design of Alloys for Energy Technologies

Advanced materials that maintain their mechanical performance under elevated temperatures, corrosive environments, and a range of static and evolving stresses are needed to improve the efficiency and reduce the environmental impact of a wide spectrum of energy technologies. For instance, cost-efficient alloys that can withstand high temperatures (e.g., 700 °C) have a critical role in improving the efficiency and economics of power generation to support decarbonization of the energy sector; such is true of both the nuclear and fossil energy sectors. Considering both the threats of the energy crisis, namely soaring costs of greenhouse gas emission-producing energy and climate change, it is essential to increase the pace of material discovery and enable rapid paths for material qualification to advance clean energy technologies. Conventionally, alloy development has followed a slow Edisonian process that uses repeated cycles of making, characterizing, and modifying to arrive at optimum composition and processing conditions to achieve the desired component performance. This optimization is followed by the necessary stepwise materials qualification. Furthermore, the increasing adoption of sound data management and physics-informed machine learning represents the next step in the acceleration of materials design and development. In the integrated computational materials engineering (ICME) approach, computational modeling and simulation data from different length and time scales can be combined with complex microstructural details from multimodal experimental characterization and selective property testing to close the design loop for rapid alloy development.

Computational Design Of Materials↗

The fourth spectrum of iridium (Ir IV)

The spectrum of three times ionized iridium, Ir IV, was investigated in the 650–2045 Å wavelength region. The analysis has led to the determination of the 5d{sup 6}, 5d{sup 5}6s and 5d{sup 5}6p configurations. Twenty-nine of 34 theoretically possible 5d{sup 6} levels, 44 of 74 possible 5d{sup 5}6s levels and 150 of 214 possible 5d{sup 5}6p levels have been established. The levels are based on 1348 classified spectral lines. The level structure and transition probabilities were calculated using the orthogonal operators technique. The energy parameters have been determined by the least squares fit to the observed levels. Calculated energy values and LS-compositions obtained from the fitted parameter values are given. The level optimization procedure and the determination of uncertainties of the obtained energy level values are discussed.

74 ATOMIC AND MOLECULAR PHYSICS↗

Structure-property relationships and recyclability of natural fiber insulation

Thermal insulation can significantly decrease the energy required to maintain internal temperatures within buildings, saving money and decreasing environmental impacts. Many industrially available insulation options utilize petroleum-derived materials, such as polyurethane, fiberglass, and polystyrene, which can be detrimental to the environment by emitting greenhouse gases during production. A sustainable alternative to these synthetic insulations is the use of renewable feedstocks to produce comparable insulation products. In this work, natural fibers such as flax and banana were bound with an epoxy system to produce natural-fiber insulation. Key experimental parameters for this study included evaluating the fiber lengths and processing methods while varying the viscosity of the epoxy binder solvent dissolution. Insulation performance was determined by comparing density, thermal conductivity, resilience, and compressive strength; these parameters were tested to further understand and investigate the structure- property relationships within the system and to understand how these composites compare to current commercial materials. Furthermore, from this characterization and optimization, a natural fiber sample with an R/in. >5 was achieved, making these materials competitive with commercial alternatives.

Compressive strength↗