Search NASA⌕ Search

SEARCH · Search NASA

Results for “conduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Breakthrough Conductivity Enhancement in Deep Eutectic Solvents via Grotthuss–Type Proton Transport

There is an increasing demand for the development of ion-conducting electrolytes for energy storage systems. Much attention is directed toward deep eutectic solvents as potential candidates. In the search for highly conductive systems, the possibility of designing deep eutectic solvents with Grotthuss-type proton transport is widely overlooked. Herein, ethaline, a mixture of choline chloride and ethylene glycol is used in a 1:2 molar ratio, to induce a significant conductivity increase with the addition of water and sulfuric acid (H 2 SO 4 ). The achieved breakthrough conductivity is analyzed experimentally and simulated with ab initio molecular dynamics (AIMD). At sufficient water content, an H-bonding network is formed that leads to a significant breakthrough conductivity based on H 2 SO 4 -derived proton transfer following the long-established Grotthuss proton transport mechanism. This result is substantiated by the positive deviation from the ideal KCl line in the Walden plot. Specifically, the data series positioned above the reference line indicates a Grotthuss mechanism in action. The AIMD simulations demonstrate proton transfer between water and ethylene glycol, supported by simulation frames captured at various times.

36 MATERIALS SCIENCE↗

Engineering Electrical Transport by Implantation‐Induced Defects in CrN Films Without Affecting Thermal Conductivity

The transport properties of CrN thin films deposited on sapphire have been tailored through structural modifications induced by cumulative argon implantation. As-grown samples experience the typical structural transition in CrN films from orthorhombic at low temperature to cubic above the Néel temperature (≈280 K) and exhibit a metallic-like conduction in both phases. With increasing implantation dose, the conduction mode shifts to a semiconductor-like behavior in both phases, albeit at different damage levels. Analysis of the results suggests that hopping conduction becomes dominant beyond a given damage threshold. The results highlight a promising correlation between defect engineering and conduction mechanisms, offering valuable insights into the versatile electrical properties of CrN films. These implantation-induced defects scatter carriers, leading to a decrease in their mobility. As the implantation dose increases, the defect landscape evolves, modifying the density of states. However, up to a dose of 0.050 dpa, no significant influence on phonon scattering is observed. This approach demonstrates that ion implantation enables precise tuning of CrN's electrical properties without affecting thermal conductivity, offering valuable insights into defect engineering in transition metal nitrides and underscoring its potential for transport properties decorrelation.

defects↗

Anomalously Suppressed Thermal Conduction by Electron-Phonon Coupling in Charge-Density-Wave Tantalum Disulfide

Charge and thermal transport in a crystal is carried by free electrons and phonons (quantized lattice vibration), the two most fundamental quasiparticles. Above the Debye temperature of the crystal, phonon-mediated thermal conductivity ( κ L ) is typically limited by mutual scattering of phonons, which results in κ L decreasing with inverse temperature, whereas free electrons play a negligible role in κ L . Here, an unusual case in charge-density-wave tantalum disulfide (1T-TaS 2 ) is reported, in which κ L is limited instead by phonon scattering with free electrons, resulting in a temperature-independent κ L . In this system, the conventional phonon–phonon scattering is alleviated by its uniquely structured phonon dispersions, while unusually strong electron-phonon (e-ph) coupling arises from its Fermi surface strongly nested at wavevectors in which phonons exhibit Kohn anomalies. The unusual temperature dependence of thermal conduction is found as a consequence of these effects. The finding reveals new physics of thermal conduction, offers a unique platform to probe e-ph interactions, and provides potential ways to control heat flow in materials with free charge carriers. The temperature-independent thermal conductivity may also find thermal management application as a special thermal interface material between two systems when the heat conduction between them needs to be maintained at a constant level.

36 MATERIALS SCIENCE↗

Thickness-Dependent Thermal Conductivity and Phonon Mean Free Path Distribution in Single-Crystalline Barium Titanate

Nanosized perovskite ferroelectrics are widely employed in several electromechanical, photonics, and thermoelectric applications. Scaling of ferroelectric materials entails a severe reduction in the lattice (phonon) thermal conductivity, particularly at sub-100 nm length scales. Such thermal conductivity reduction can be accurately predicted using the information of phonon mean free path (MFP) distribution. The current understanding of phonon MFP distribution in perovskite ferroelectrics is still inconclusive despite the critical thermal management implications. Here, high-quality single-crystalline barium titanate (BTO) thin films, a representative perovskite ferroelectric material, are grown at several thicknesses. Using experimental thermal conductivity measurements and first-principles based modeling (including four-phonon scattering), the phonon MFP distribution is determined in BTO. The simulation results agree with the measured thickness-dependent thermal conductivity. The results show that the phonons with sub-100 nm MFP dominate the thermal transport in BTO, and phonons with MFP exceeding 10 nm contribute ≈35% to the total thermal conductivity, in significant contrast to previously published experimental results. The experimentally validated phonon MFP distribution is consistent with the theoretical predictions of other complex crystals with strong anharmonicity. This work paves the way for thermal management in nanostructured and ferroelectric-domain-engineered systems for oxide perovskite-based functional materials.

36 MATERIALS SCIENCE↗

Significantly Promoting the Thermal Conductivity and Machinability of Negative Thermal Expansion Alloy via In Situ Precipitation of Copper Networks

Rapid advancements in electronic devices yield an urgent demand for high-performance electronic packaging materials with high thermal conductivity, low thermal expansion, and great mechanical properties. However, it is a great challenge for current design philosophies to fulfill all the requirements simultaneously. Here, an effective strategy is proposed for significantly promoting the thermal conductivity and machinability of negative thermal expansion alloy (Zr,Nb)Fe 2 through eutectic precipitation of copper networks. The eutectic dual-phase alloy exhibits an isotropic chips-matched thermal expansion coefficient and a thermal conductivity enhancement exceeding 200% compared with (Zr,Nb)Fe 2 , along with an ultimate compressive strength of 550 MPa. The addition of copper reorganizes the composition of (Zr,Nb)Fe 2 , which smooths the magnetic transition and shifts it toward higher temperature, resulting in linear low thermal expansion in a wide temperature range. The highly fine eutectic copper lamellae construct high thermal conductivity networks within (Zr,Nb)Fe 2 , serving as highways for heat transfer electrons and phonons. The in situ forming of eutectic copper lamellae also facilitates the mechanical properties by enhancing interfacial bonding and bearing additional stress after yielding of (Zr,Nb)Fe 2 . This work provides a novel strategy for promoting thermal conductivity and mechanical properties of negative thermal expansion alloys via eutectic precipitation of copper networks.

36 MATERIALS SCIENCE↗

Isoreticular Linker Substitution in Conductive Metal–Organic Frameworks with Through–Space Transport Pathways

The extension of reticular chemistry concepts to electrically conductive three-dimensional metal–organic frameworks (MOFs) has been challenging, particularly for cases in which strong interactions between electroactive linkers create the charge transport pathways. Here, we report the successful replacement of tetrathiafulvalene (TTF) with a nickel glyoximate core in a family of isostructural conductive MOFs with Mn 2+ , Zn 2+ , and Cd 2+ . Different coordination environments of the framework metals lead to variations in the linker stacking geometries and optical properties. Single-crystal conductivity data are consistent with charge transport along the linker stacking direction, with conductivity values only slightly lower than those reported for the analogous TTF materials. Lastly, these results serve as a case study demonstrating how reticular chemistry design principles can be extended to conductive frameworks with significant intermolecular contacts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal conductivity of salvaged fused cast alumina used in the glass industry

Fused cast alumina (FCA) has been and continues to be used as a refractory material in energy intensive industries such as glass melting and chemical processing. In-service degradation due to high temperature exposure in harsh environment affects the designed furnace thermal profiles and energy consumption. Phase transformation may occur at the refractory hot face during glass melting altering the properties. Three FCA blocks recovered from industrial furnaces were investigated in this study. The as-received FCA consists primarily of a mixture of alpha (α) and beta (β) alumina that has a thermal conductivity value of 5–6 W/mK. The Hot Disk method was used to obtain thermal conductivity directly on the refractory blocks. At the hot face, a transformation from β to α alumina occurred and was confirmed by an X-ray diffraction study. Thermal conductivity measurements as a function of position also showed a clear transition from β to α alumina at both ends of a complete block with no voids. Thermal conductivity of the α alumina tripled compared to β alumina. This study provides important information of heat transfer and thermal conductivity evolution to refractory manufacturers and users.

36 MATERIALS SCIENCE↗

Comparison of Different Upscaling Methods for Predicting Thermal Conductivity of Complex Heterogeneous Materials System: Application on Nuclear Waste Forms

To develop a strategy in thermal conductivity prediction of a complex heterogeneous materials system, loaded nuclear waste forms, the computational efficiency and accuracy of different upscaling methods have been evaluated. The effective thermal conductivity, obtained from microstructure information and local thermal conductivity of different components, is critical in predicting the life and performance of waste form during storage. Several methods, including the Taylor model, Sachs model, self-consistent model, and statistical upscaling method, were developed and implemented. Microstructure based finite element method (FEM) prediction results were used to as benchmark to determine the accuracy of the different upscaling methods. Micrographs from waste forms with varying waste loadings were used in the prediction of thermal conductivity in FEM and homogenization methods. Prediction results demonstrated that in term of efficiency, boundary models (e.g., Taylor model and Sachs model) are stronger than the self-consistent model, statistical upscaling method, and finite element method. However, when balancing computational efficiency and accuracy, statistical upscaling is a useful method in predicting effective thermal conductivity for nuclear waste forms.

36 MATERIALS SCIENCE↗

Experimental Study on Electrical Conductivity of MnO-CaO-SiO{sub 2} Slags at 1723 K to 1823 K (1450 °C to 1550 °C) and Various Oxygen Potentials

The electrical conductivity of molten slag has many important and practical effects in modeling and operating the electric smelting furnace. In the present study, the electrical conductivities (total and electronic/ionic properties) of MnO-CaO-SiO{sub 2} slags were measured by a four-electrode method at different oxygen potentials and temperatures. Experimental results show that the effects of temperature on the total, electronic, and ionic conductivities obey the Arrhenius law, and all conductivities increase when increasing the temperature. The stepped potential chronoamperometry method was used to measure the electronic transference number, which is affected strongly by oxygen potential but is unaffected by temperature. The total electrical, electronic, and ionic conductivities present similar increasing trends when increasing the CO/CO{sub 2} ratio, which resulted from increasing Mn{sup 2+}.

36 MATERIALS SCIENCE↗

An International Round-Robin Study, Part II: Thermal Diffusivity, Specific Heat and Thermal Conductivity

For bulk thermoelectrics, figure-of-merit, ZT, still needs to improve from the current value of 1.0 - 1.5 to above 2 to be competitive to other alternative technologies. In recent years, the most significant improvements in ZT were mainly due to successful reduction of thermal conductivity. However, thermal conductivity cannot be measured directly at high temperatures. The combined measurements of thermal diffusivity and specific heat and density are required. It has been shown that thermal conductivity is the property with the greatest uncertainty and has a direct influence on the accuracy of the figure of merit. The International Energy Agency (IEA) group under the implementing agreement for Advanced Materials for Transportation (AMT) has conducted two international round-robins since 2009. This paper is Part II of the international round-robin testing of transport properties of bulk bismuth telluride. The main focuses in Part II are on thermal diffusivity, specific heat and thermal conductivity.

specific heat↗

Microstructure Evolution and Failure Analysis of an Aluminum–Copper Cathode Conductive Head Produced by Explosive Welding

In this paper, microstructure evolution and failure analysis of the aluminum-copper interface of cathode conductive heads during their use were studied. The interface morphologies, compositions, conductivity and mechanical properties were investigated and analyzed. Obvious corrosion was found on the surface of the contact interface, which was more prevalent on an Al matrix. The crack increased sharply in the local metallurgical bonding areas on the interface, with the compound volume having no significant change. The phase transformation occurred on the interface during use, which was investigated using the elemental composition and x-ray diffraction pattern. The microhardness near the interface increased accordingly. An obvious electrical conductivity decrease appeared on the Al/Cu interface of the cathode conductive head after use over a specific time interval. Therefore, the deterioration of the microstructures and corrosion are the primary factors that affect the electrical conductivity and effective bonding, which will lead to eventual failure.

36 MATERIALS SCIENCE↗

A Study on Thermal Conductivity and Stability of Nanofluids Containing Chemically Synthesized Nanoparticles for Advanced Thermal Applications

This study presents easy methods of synthesizing silver (Ag) and copper (Cu) nanoparticles through chemical route in an aqueous medium under atmospheric condition at ambient temperature. The synthesized nanoparticles have been characterized with different techniques, such as x-ray diffraction, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, energy-dispersive x-ray spectroscopy, high-resolution transmission electron microscopy, UV–visible spectroscopy and dynamic light scattering measurements. Experimental observations have revealed the absence of any metal oxide layer around the nanoparticles which are found to remain stable under ambient conditions. The featured properties, such as narrow size distribution, stability, make these nanoparticles potential candidates for the synthesis of effective nanofluids. The nanofluids have been prepared by dispersing the nanoparticles synthesized through chemical route in a suitable base fluid. The thermal conductivity of nanofluids with different nanoparticles loading has been measured by transient hot-wire method, and the results have shown that the increasing trend of enhancement in thermal conductivity with respect to nanoparticles concentration is attainable only when the nanoparticles concentration is below some limiting value depending on the type of nanofluid. Beyond this limiting value of loading, the thermal conductivity of the nanofluid decreases due to pronounced agglomeration effect. The measurements of thermal conductivity of nanofluids over varying temperatures for a given volume fraction loading of nanoparticles have shown that the thermal conductivity increases markedly with the increase in temperature. Hence, nanofluids are likely to be much more promising at high-temperature applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of magnesia-to-phosphate molar ratio on microstructures, mechanical properties and thermal conductivity of magnesium potassium phosphate cement paste with large water-to-solid ratio

This paper describes the influence of the magnesia-to-phosphate (M/P) molar ratios ranging from 4 to 12, on the properties and microstructures of magnesium potassium phosphate cement (MKPC) pastes with a large water-to-solid ratio (w/s) of 0.50. The setting behavior, compressive strength, tensile bonding strength and thermal conductivity of the MKPC pastes, were investigated. The results show that an increase in the M/P ratio can slow down the setting reaction, and clearly degrade the mechanical strengths, but clearly improve the thermal conductivity of MKPC pastes. Furthermore, micro-characterizations including X-ray diffraction, scanning electron microscopy and thermogravimetric analysis, on the MKPC pastes reveal that a lower M/P ratio can facilitate better crystallization of the resultant magnesium potassium phosphate hexahydrate (MKP) and a denser microstructure. Moreover, strong linear correlations are found between the mechanical strengths and the MKP-to-space ratio, and between thermal conductivity and the volume ratio of the unreacted magnesia to the MKP. - Highlights: • Increase of M/P molar ratio causes clear mechanical degradations on MKPC pastes. • Thermal conductivity of MKPC pastes is improved with increase of M/P molar ratio. • Lower M/P ratio leads to better MKP crystallization and denser microstructure. • Strengths of MKPC pastes are linearly correlated to the MKP-to-space ratios. • Thermal conductivity is affected by the volume ratio of unreacted magnesia to MKP.

36 MATERIALS SCIENCE↗

Simulated lightning strike investigation of CFRP comprising a novel Polyaniline/Phenol based electrically conductive resin matrix

Traditional carbon fiber reinforced plastics (CFRPs) have been reported to exhibit lower electrical conductivity in the through-thickness direction, and have since paved the path for developing new resin systems to improve the through-thickness electrical conductivity and functionality of CFRP laminates. This work designs and investigates a novel Polyaniline (PANI)/Phenol resin, which possesses high electrical conductivity and mechanical strength. The CFRP manufactured by this PANI/Phenol resin with an addition of up to (~23.30%) phenol resulted in 0.6 S/cm through-thickness conductivity and demonstrated flexural strength and modulus values of 477 MPa and 59.2 GPa, respectively. We further evaluate the effectiveness of lightning strike protection of PANI/Phenol-based conductive CFRP laminates with a simulated lightning strike test. In essence, this research reports on PANI/Phenol-based CFRP's effectiveness as a material for lightning suppression without applying traditional metal-based lightning strike protection (LSP) systems.

36 MATERIALS SCIENCE↗

Tailored crosslinking of Poly(ethylene oxide) enables mechanical robustness and improved sodium-ion conductivity

We report that sodium-based energy storage systems are promising candidates for electric vehicles and grid-level energy storage applications. The advancement of sodium-based energy storage systems relies on the development of high performance sodium-ion conducting electrolytes and membranes that exhibit high ionic conductivity and mechanical stability. A crosslinked poly(ethylene oxide) based polymer electrolyte was developed that demonstrates high ionic conductivity, as well as excellent mechanical stability over a wide temperature range. Ionic conductivities up to 2.0 × 10 -4 S/cm at 20 °C and 7.1 × 10 -4 S/cm at 70 °C are achieved for the plasticized membrane, almost four orders of magnitude greater than that of the non-plasticized membrane. The membranes are mechanically robust, and the storage modulus of the membrane is maintained at ~1 MPa from -20 to 180 °C even with the addition of plasticizer. In conclusion, this study provides a synthesis approach towards the design of highly ion conducting, mechanically robust gel polymer electrolytes for Na-ion batteries, non-aqueous flow batteries, and many other applications.

25 ENERGY STORAGE↗

Experimental investigations and theoretical determination of thermal conductivity and viscosity of Al{sub 2}O{sub 3}/water nanofluid

Experimental investigations and theoretical determination of effective thermal conductivity and viscosity of Al{sub 2}O{sub 3}/H{sub 2}O nanofluid are reported in this paper. The nanofluid was prepared by synthesizing Al{sub 2}O{sub 3} nanoparticles using microwave assisted chemical precipitation method, and then dispersing them in distilled water using a sonicator. Al{sub 2}O{sub 3}/water nanofluid with a nominal diameter of 43 nm at different volume concentrations (0.33-5%) at room temperature were used for the investigation. The thermal conductivity and viscosity of nanofluids are measured and it is found that the viscosity increase is substantially higher than the increase in thermal conductivity. Both the thermal conductivity and viscosity of nanofluids increase with the nanoparticle volume concentration. Theoretical models are developed to predict thermal conductivity and viscosity of nanofluids without resorting to the well established Maxwell and Einstein models, respectively. The proposed models show reasonably good agreement with our experimental results. (author)

36 MATERIALS SCIENCE↗

Measurements of the thermal conductivity of reference liquids using a modified transient hot-wire needle probe

Many power generation processes feature some type of working fluid that plays a critical role in the transfer of heat throughout the system. To optimize thermal efficiencies, an accurate characterization of the temperature-dependent thermal conductivity of the fluid is needed. Herein, this study develops a time-domain Modified Transient Hot-wire Needle Probe to overcome phenomena that have impaired traditional measurement techniques when the fluid is both corrosive and at an elevated temperature. First, the physical design of the instrument is presented to demonstrate features that limit interference from corrosion, electrical conduction, and convective and radiative heat transfer. Next, a governing equation for 1D (radial) heat conduction is fully developed using the thermal quadrupoles technique. A finite-element study is performed for validation. A sensitivity analysis is done to assess the time-dependent influence of critical parameters in the governing equation for several samples. Finally, thermal conductivity measurements are presented for seven different liquid substances by fitting the thermal model to experimental data across a range of temperatures. Reference correlations are included for comparison. The sample thermal conductivity and ambient temperature of the experimental conditions range from 0.125–16.5$\frac{W}{m·K}$ and 10–400°C, respectively. The total uncertainty, comprised of both the experimental design and fitting process, of all measurements is quantified.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Room temperature thermal conductivity measurements of neat MOF-5 compacts with high pressure hydrogen and helium

Metal-organic frameworks (MOFs) are a highly porous crystalline material with potential in various applications including on-board vehicle hydrogen storage for fuel cell vehicles. The thermal conductivity of MOFs is an important parameter in the design and ultimate performance of an on-board hydrogen storage system. However, in-situ thermal conductivity measurements have not been previously reported. The present study reports room temperature thermal conductivity and thermal diffusivity measurements performed on neat MOF-5 cylindrical compacts (ρ = 0.4 g/mL) as a function of pressure (0.27–90 bar) and gas type (hydrogen and helium). The transient plane source technique was used to measure both the non-directional thermal properties (isotropic method) and the directional thermal properties (anisotropic method). High pressure measurements were made using our in-house built low-temperature, high pressure thermal conductivity sample cell. The intrinsic thermal properties of neat MOF-5 measured under vacuum were—Isotropic: k isotropic = 0.1319 W/m K, α isotropic = 0.4165 mm 2 /s; Anisotropic: k axial = 0.1477 W/m K, k radial = 0.1218 W/m K, α axial = 0.5096 mm 2 /s, and α radial = 0.4232 mm 2 /s. The apparent thermal properties of neat MOF-5 increased with increasing hydrogen and helium pressure, with the largest increase occurring in the narrow pressure range of 0–10 bar and then monotonically asymptoting with increasing pressures up to around 90 bar. On average, a greater than two-fold enhancement in the apparent thermal properties was observed with neat MOF-5 in the presence of helium and hydrogen compared to the intrinsic values of neat MOF-5 measured under vacuum. The apparent thermal properties of neat MOF-5 measured with hydrogen were higher than those measured with helium, which were directly related to the gas-specific thermal properties of helium and hydrogen. Neat MOF-5 exhibited a small degree of anisotropy under all conditions measured with thermal conductivities and diffusivities in the axial direction being higher than those in the radial direction. As a result, the low temperature specific heat capacities of neat MOF-5 were also measured and reported for the temperature range of 93–313 K (–180–40 °C).

36 MATERIALS SCIENCE↗