Search NASA⌕ Search

SEARCH · Search NASA

Results for “coordinated response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Nonlinear Interface Reduction for Time-Domain Analysis of Hurty/Craig-Bampton Superelements with Frictional Contact

Virtual prototyping in engineering design relies today on modern numerical models of contacting structures with accurate resolution of interface mechanics, which strongly affect the system-level stiffness and energy dissipation due to frictional losses. High-fidelity modeling within the localized interfaces is required to resolve local quantities of interest that may drive design decisions. The high-resolution finite element meshes necessary to resolve inter-component stresses tend to be computationally expensive, particularly when the analyst is interested in response time histories. The Hurty/Craig-Bampton (HCB) transformation is a widely used method in structural dynamics for reducing the interior portion of a finite element model while having the ability to retain all nonlinear contact degrees of freedom (DOF) in physical coordinates. These models may still require many DOF to adequately resolve the kinematics of the interface, leading to inadequate reduction and computational savings. This study proposes a novel interface reduction method to overcome these challenges by means of system-level characteristic constraint (SCC) modes and properly orthogonal interface modal derivatives (POIMDs) for transient dynamic analyses. Both SCC modes and POIMDs are computed using the reduced HCB mass and stiffness matrices, which can be directly computed from many commercial finite element analysis software. Comparison of time history responses to an impulse-type load in a mechanical beam assembly indicate that the interface-reduced model correlates well with the HCB truth model. Localized features like slip and contact area are well-represented in the time domain when the beam assembly is loaded with a broadband excitation. The proposed method also yields reduced-order models with greater critical timestep lengths for explicit integration schemes.

42 ENGINEERING↗

Coordinated Control of Wind Turbine and Energy Storage System for Reducing Wind Power Fluctuation

This paper proposes a method for the coordinated control of a wind turbine and an energy storage system (ESS). Because wind power (WP) is highly dependent on wind speed, which is variable, severe stability problems can be caused in power systems, especially when the WP has a high penetration level. To solve this problem, many power generation corporations or grid operators have begun using ESSs. An ESS has very quick response and good performance for reducing the impact of WP fluctuation; however, its installation cost is high. Therefore, it is important to design the control algorithm by considering both the ESS capacity and WP fluctuation. Thus, we propose a control algorithm to mitigate the WP fluctuation by using the coordinated control between the wind turbine and the ESS by considering the ESS capacity and the WP fluctuation. Using de-loaded control, according to the WP fluctuation and ESS capacity, we can expand the ESS lifespan and improve grid reliability by avoiding the extreme value of state of charge (SoC) (i.e., 0 or 1 pu). The effectiveness of the proposed method was validated via MATLAB/Simulink by considering a small power system that includes both a wind turbine generator and conventional generators that react to system frequency deviation. We found that the proposed method has better performance in SoC management, thereby improving the frequency regulation by mitigating the impact of the WP fluctuation on the small power system.

17 WIND ENERGY↗

Control approach for power modulation of end-use loads

Methods, apparatus, and systems are disclosed herein for power modulation control of power grids using end-use loads. At the beginning of a coordination period typically lasting a few minutes, a population of end-use loads (water heaters, air conditioners, plug-in electric vehicles, etc.) is interrogated for their willingness to participate in power modulation by undergoing state transitions from on to off, or off to on. Distribution system flexibilities are calculated from the sums of device powers within distribution systems. Area flexibilities are calculated from the sums of device powers within areas. Thresholds for various devices to change state in response to inter-area oscillation damping or frequency regulation are derived from these flexibilities. Two power functions are monitored in real-time and compared with the device thresholds to trigger state changes which then remain locked throughout the remainder of the coordination period, then the devices are released from the lockout state.

Lian, Jianming↗

Structural Studies of the Nudix GDP-mannose Hydrolase from E. coli Reveals a New Motif for Mannose Recognition

The Nudix hydrolase superfamily, characterized by the presence of the signature sequence GX5EX7REUXEEXGU (where U is I, L, or V), is a well-studied family in which relations have been established between primary sequence and substrate specificity for many members. For example, enzymes that hydrolyze the diphosphate linkage of ADP-ribose are characterized by having a proline 15 amino acids C-terminal of the Nudix signature sequence. GDPMK is a Nudix enzyme that conserves this characteristic proline but uses GDP-mannose as the preferred substrate. By investigating the structure of the GDPMK alone, bound to magnesium, and bound to substrate, the structural basis for this divergent substrate specificity and a new rule was identified by which ADP-ribose pyrophosphatases can be distinguished from purine-DP-mannose pyrophosphatases from primary sequence alone. Kinetic and mutagenesis studies showed that GDPMK hydrolysis does not rely on a single glutamate as the catalytic base. Instead, catalysis is dependent on residues that coordinate the magnesium ions and residues that position the substrate properly for catalysis. GDPMK was thought to play a role in biofilm formation because of its upregulation in response to RcsC signaling; however, GDPMK knockout strains show no defect in their capacity of forming biofilms.

59 BASIC BIOLOGICAL SCIENCES↗

OC6 Phase Ib: Validation of the CFD predictions of difference-frequency wave excitation on a FOWT semisubmersible

During the previous OC5 11 project, state-of-the-art mid-fidelity engineering tools for floating wind systems were found to consistently underpredict the nonlinear, low-frequency responses of semisubmersible offshore wind platforms, leading to substantial errors in the structural loads because of low-frequency surge and pitch resonance. To examine this underprediction, a coordinated investigation with computational fluid dynamics (CFD) simulations and model-basin experiments was carried out. Both investigations involved a fixed and simplified OC5-DeepCwind semisubmersible in bichromatic waves. The wave excitations - especially the nonlinear, difference-frequency excitation - on the structure from the CFD simulations were compared to the experimental measurements for validation, with uncertainty analyses for both the experimental and the CFD results. Furthermore, the wave excitations on each column of the semisubmersible were measured separately in the experiment, allowing the validation of the CFD results to be done on a per-column basis. Overall, the CFD predictions of the difference-frequency excitations agree with the experimental measurements, suggesting the CFD solutions can be used as a reference for tuning and improving the engineering-level tools and can provide a means to better understand the underprediction at low frequencies.

16 TIDAL AND WAVE POWER↗

Electronic Configurational Transformation of Network Modifiers in Aluminate Glass above Megabar Pressures

Electronic responses of glasses under extreme pressures differ from those of crystalline analogs. Their distinct electronic environments are found in network formers with well-defined, covalent-bonded coordination environments (e.g., [4] Si and [4] Al) and in network modifiers with more disordered, ionic-bonded configurations (e.g., [5,6,7] Ca). Deciphering the evolution of the bonding environment of network modifier cations upon compression provides atomic insights into the pressure-driven hardening and transport properties of glasses. Despite the importance, in contrast to extensive efforts to uncover how network formers behave under pressure, considerable structural disorder around network modifiers makes it challenging to probe their electronic bonding environments under compression. Our understanding of the evolution of network modifiers above megabars is currently absent. Here, we report a discovery of highly densified electronic configurations of network modifier Ca in aluminate glass under extreme compression via the first inelastic X-ray scattering at the Ca L-edge up to 140 GPa. As evidenced by the prominent pressure-driven increases in electronic dispersion and delocalization, densified calcium environments are characterized by a decreased average Ca–O distance, the formation of highly coordinated calcium, a broader distribution of topological variables, and a greater distortion of Ca polyhedra above megabars. The spectral features for the Ca environments reveal significant electronic and bonding modifications, including pressure-driven increases in the ligand field interaction, the covalence characteristic of the Ca–O bond, and the electron–hole Coulomb interaction. These densification paths identify the electronic adaptation of network modifiers above megabars, shedding light on the origins of enhanced electron transport and the electron-storing capacity of glasses under pressure.

amorphous materials↗

Fine-Tuning the Activity of Metal–Organic Framework Supported Cobalt Catalysts for the Oxidative Dehydrogenation of Propane

Few-atom cobalt-oxide clusters, when dispersed on a Zr-based metal–organic framework (MOF) NU-1000, have previously been shown to be active for the oxidative dehydrogenation (ODH) of propane at low temperatures (< 230 °C), affording a selective and stable propene production catalyst. In our current work, a series of promoter ions with varying Lewis acidity, including Ni(II), Zn(II), Al(III), Ti(IV) and Mo(VI), are anchored as metal-oxide,hydroxide clusters to NU-1000 via SIM (solvothermal deposition within MOFs–specifically the nodes) followed by incorporation of Co(II) ions via vapor-phase AIM (atomic layer deposition (ALD) in MOFs). This process yields a series of NU-1000-supported bimetallic-oxo,hydroxo,aqua clusters. Using difference envelope density (DED) analyses, the spatial locations of the promoter ions and catalytic cobalt ions are determined. For all samples the SIM-anchored promoter ions are sited between pairs of Zr 6 nodes along the MOF c-axis (channel-aligned axis) whereas the location of the AIM-anchored cobalt ions varies depending on the identity of promoter metal ion. With Ni(II)-, Al(III)-, or Ti(IV)-containing clusters as promoters, the oxy-cobalt species are sited atop the promoter sites; with Mo(VI) they grow exclusively on the MOF nodes sites (hexa-Zr(IV)- oxo,hydroxo,aqua units); with Zn(II) they grow on both the node and promoter. The NU-1000- supported bimetallic-oxide clusters are active for propane ODH after thermal activation under O 2 to open a cobalt coordination site and to oxidize Co(II) to Co(III), as evidenced by operando Xray absorption spectroscopy at the Co K-edge. The cobalt component is exclusively responsible for the observed catalysis. In accord with the decreasing Lewis acidity of the promoter ion, catalytic activity increases in the order: Mo(VI)<Ti(IV)<Al(III)<Zn(II)<Ni(II). The finding is attributed to increasing ease of formation Co(III)-O• species and stabilization of a cobalt(III)- oxyl/propane transition state as the Lewis acidity of the promoter ions decreases. (The promoterfree catalyst is sited on the oxy-Zr(IV) node of the MOF and is inferior catalytically to the strongly promoted versions of the catalyst.) The relative Lewis acidities of the promoters are inferred from the initial pKa values of aqua complexes of the corresponding single metal ions. Departures from the (ODH-rate)/(promoter-pKa) correlation are paralleled by differences in cobalt catalyst siting or structure. The combined results point to an increasing ability to fine-tune, with close to atomic specificity, the structure-dependent activity of MOF-supported heterogeneous catalysts for gas phase chemical reactions. When coupled with mechanistic studies–computational or experimental–this ability may translate into informed prediction of improved catalysts for propane ODH and other chemical reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Temperature-dependent morphology of hybrid nanoflowers from elastin-like polypeptides

We report a method for creating hybrid organic-inorganic “nanoflowers” using calcium or copper ions as the inorganic component and a recombinantly expressed elastin-like polypeptide (ELP) as the organic component. Polypeptides provide binding sites for the dynamic coordination with metal ions, and then such noncovalent complexes become nucleation sites for primary crystals of metal phosphates. We have shown that the interaction between the stimuli-responsive ELP and Ca{sup 2+} or Cu{sup 2+}, in the presence of phosphate, leads to the growth of micrometer-sized particles featuring nanoscale patterns shaped like flower petals. The morphology of these flower-like composite structures is dependent upon the temperature of growth and has been characterized by scanning electron microscopy. The composition of nanoflowers has also been analyzed by energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The temperature-dependent morphologies of these hybrid nanostructures, which arise from the controllable phase transition of ELPs, hold potential for morphological control of biomaterials in emerging applications such as tissue engineering and biocatalysis.

36 MATERIALS SCIENCE↗

New characterization techniques for LSST sensors

Fully depleted, thick CCDs with extended infra-red response have become the sensor of choice for modern sky surveys. The charge transport effects in the silicon and associated astrometric distortions could make mapping between the sky coordinates and sensor coordinates non-trivial, and limit the ultimate precision achievable with these sensors. Two new characterization techniques for the CCDs, which both could probe these issues, are discussed: x-ray flat fielding and imaging of pinhole arrays.

Si-PMTs↗

The role of photorespiration in plant immunity

To defend themselves in the face of biotic stresses, plants employ a sophisticated immune system that requires the coordination of other biological and metabolic pathways. Photorespiration, a byproduct pathway of oxygenic photosynthesis that spans multiple cellular compartments and links primary metabolisms, plays important roles in defense responses. Hydrogen peroxide, whose homeostasis is strongly impacted by photorespiration, is a crucial signaling molecule in plant immunity. Photorespiratory metabolites, interaction between photorespiration and defense hormone biosynthesis, and other mechanisms, are also implicated. An improved understanding of the relationship between plant immunity and photorespiration may provide a much-needed knowledge basis for crop engineering to maximize photosynthesis without negative tradeoffs in plant immunity, especially because the photorespiratory pathway has become a major target for genetic engineering with the goal to increase photosynthetic efficiency.

59 BASIC BIOLOGICAL SCIENCES↗

Visual/motion simulation of CTOL flare and touchdown comparing data obtained from two model board display systems

Acquisition of a modern terrain model board display system for 'out-the-window' scene presentation has allowed for the repetition of an evaluation study of combined visual/motion cues for CTOL flare and touchdown control that was originally carried out on a 1965 vintage landing display system. The motion drive system used in both studies was a nonlinear coordinated adaptive washout based on the method of continuous steepest descent optimization. Comparisons of the results of the studies present flare and touchdown data, as well as dynamic response data, from the two visual landing systems. The new visual system also allowed for the repetition, under visual conditions, of a subjective comparison of a linear and a nonlinear motion washout method done previously under instrument conditions.

Parrish, R. V.↗

Nonlinear and tangent stiffness of imperfect beam columns

A curved member under axial load is analyzed using beam column theory to determine nonlinear response and the tangent stiffness associated with small displacements from the nonlinear state. Such a result is suitable for incorporation into a general nonlinear analysis using a corotational coordinate system to describe the rigid body type motion of individual members. The method is applied to buckling problems. Several examples are given to show the accuracy of the method.

Anderson, M. S.↗

Magnetic configuration of the Venus magnetosheath

A data set consisting of nearly six Venus years of Pioneer Venus Orbiter magnetometer data is analyzed in order to describe the configuration of the magnetosheath. A coordinate system is developed which isolates the effects of the solar wind flow and the interplanetary magnetic field (IMF). The data indicate that the magnetosheath field magnitude is responsive to solar wind dynamic pressure and that the compression of the upstream field is controlled by magnetosonic Mach number. The draping of the field is similar to that predicted by gasdynamic modeling; specific draping features include distinct dependence on the radial and the transverse components of the IMF, and a tendency of the field to encircle the planet at low altitude. Certain features of the processes of mass loading by magnetosheath fluctuations and by the motional electric field are examined. Magnetic fluctuations can dominate the magnetosheath field for periods of low interplanetary cone angle and in general for the magnetosheath regions near the quasi-parallel part of the bow shock. The magnetosheath magnetic field magnitude displays a hemispherical asymmetry; the sense of this asymmetry is controlled by the cross-flow component of the IMF in a manner which indicates that ion pickup by the convective electric field occurs preferentially in one hemisphere. The results of this survey indicate that mass loading is a significant process which should be incorporated into computational models but that a fluid treatment of the planetary ion component may not be appropriate.

Phillips, J. L.↗

Research and Technology Objectives and Plans Summary (RTOPS)

This publication represents the NASA research and technology program for FY86. It is a compilation of the Summary portions of each of the RTOPs (Research and Technology Objectives and Plans) used for management review and control of research currently in progress throughout NASA. The RTOP summary is designed to facilitate communication and coordination among concerned technical personnel in government, industry, and universities. The first section containing citations and abstracts of the RTOPs is followed by four indexes: Subject, Technical Monitor, Responsible NASA Organization, and RTOP number.

Source record↗

Adaptive servo control for umbilical mating

Robotic applications at Kennedy Space Center are unique and in many cases require the fime positioning of heavy loads in dynamic environments. Performing such operations is beyond the capabilities of an off-the-shelf industrial robot. Therefore Robotics Applications Development Laboratory at Kennedy Space Center has put together an integrated system that coordinates state of the art robotic system providing an excellent easy to use testbed for NASA sensor integration experiments. This paper reviews the ways of improving the dynamic response of the robot operating under force feedback with varying dynamic internal perturbations in order to provide continuous stable operations under variable load conditions. The goal is to improve the stability of the system with force feedback using the adaptive control feature of existing system over a wide range of random motions. The effect of load variations on the dynamics and the transfer function (order or values of the parameters) of the system has been investigated, more accurate models of the system have been determined and analyzed.

Zia, Omar↗

Research and Technology Objectives and Plans Summary (RTOPS)

The NASA research and technology program for FY 1990 is presented. The summary portions is compiled of each of the RTOPs (Research and Technology Objectives and Plans) used for management review and control of research currently in progress throughout NASA. The RTOP summary is designed to facilitate communication and coordination among concerned technical personnel in government, industry, and universities. The first section containing citations and abstracts of the RTOPs is followed by four indices: Subject; Technical Monitor; Responsible NASA Organization; and RTOP number.

Source record↗

Aerodynamics of loaded cascades in subsonic flows subject to unsteady three-dimensional vortical disturbances

A highly efficient numerical method is developed for three-dimensional, periodic, vortical flows around a cascade of loaded airfoils. The method linearizes Euler's equations about the mean flow of the cascade and thus fully accounts for the effects of distortion of the vortical disturbances as they propogate and interact with the cascade mean flow. The numerical scheme is based on splitting the unsteady velocity into vortical and potential parts. The latter is governed by a non-constant coefficient inhomogeneous convective wave equation. A new and computationally suitable out-flow conditions are derived and avoid the difficulties associated with the singular velocity downstream. Solutions were obtained in the frequency domain by using a body-fitted coordinate system. Results are presented to demonstrate the effects of the out-flow boundary conditions, cascade spacing, mean blade loading and gust upstream conditions on the aerodynamics response and unsteady pressure field of a cascade.

Fang, J.↗