Search NASA⌕ Search

SEARCH · Search NASA

Results for “data transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

ET TPS Development Criteria and Flight Instrumentation Program

The objective was to verify the design thermal environments for the Space Shuttle External Tank. These environments encompassed a myraid of potential flight cases which included nominal and dispersed trajectories launched from Kennedy Space Center (KSC) and Vandenberg and abort cases. Many iterations of environments have been produced during the evolution of the Space Shuttle system which required an analysis and assessment of each environment. A significant effort was expended in the analysis and application of wind tunnel and heat transfer data to develop math/computer models. Various versions of the aeroheating computer code MINIVER were tailored to calculate ascent aeroheating environments for the External Tank. The significant environment assessment results are summarized.

Warmbrod, John D.↗

Comparison of two procedures for predicting rocket engine nozzle performance

Two nozzle performance prediction procedures which are based on the standardized JANNAF methodology are presented and compared for four rocket engine nozzles. The first procedure required operator intercedence to transfer data between the individual performance programs. The second procedure is more automated in that all necessary programs are collected into a single computer code, thereby eliminating the need for data reformatting. Results from both procedures show similar trends but quantitative differences. Agreement was best in the predictions of specific impulse and local skin friction coefficient. Other compared quantities include characteristic velocity, thrust coefficient, thrust decrement, boundary layer displacement thickness, momentum thickness, and heat loss rate to the wall. Effects of wall temperature profile used as an input to the programs was investigated by running three wall temperature profiles. It was found that this change greatly affected the boundary layer displacement thickness and heat loss to the wall. The other quantities, however, were not drastically affected by the wall temperature profile change.

Davidian, Kenneth J.↗

Structural tailoring using the SSME/STAEBL code

Space Shuttle Main Engine/Structural Tailoring of Engine Blades (SSME/STAEBL) was developed by systematically modifying and enhancing the STAEBL code developed by Pratt and Whitney under contract to NASA Lewis Research Center. STAEBL was designed for application to gas turbine blade design. Typical design variables include blade thickness distribution and root chord. Typical constraints include resonance margins, root stress, and root to chord ratios. In this program, the blade is loaded by centrifugal forces only. Additions and modifications of STAEBL included in SSME/STAEBL include (1) thermal stress analysis; (2) gas dynamic (pressure) loads; (3) temperature dependent material and thermal properties; (4) forced vibrations; (5) tip displacement constraints; (6) single crystal material analysis; (7) blade cross section stacking offsets; and (8) direct time integration algorithm for transient dynamic response. Capabilities are also included which permit data transfer from finite element models and stand-alone analysis.

Rubinstein, Robert↗

A microgravity isolation mount

The design and preliminary testing of a system for isolating microgravity sensitive payloads from spacecraft vibrational and impulsive disturbances is discussed. The Microgravity Isolation Mount (MGIM) concept consists of a platform which floats almost freely within a limited volume inside the spacecraft, but which is constrained to follow the spacecraft in the long term by means of very weak springs. The springs are realized magnetically and form part of a six degree of freedom active magnetic suspension system. The latter operates without any physical contact between the spacecraft and the platform itself. Power and data transfer is also performed by contactless means. Specifications are given for the expected level of input disturbances and the tolerable level of platform acceleration. The structural configuration of the mount is discussed and the design of the principal elements, i.e., actuators, sensors, control loops and power/data transfer devices are described. Finally, the construction of a hardware model that is being used to verify the predicted performance of the MGIM is described.

Jones, D. I.↗

Space Station alpha joint bearing

Perhaps the most critical structural system aboard the Space Station is the Solar Alpha Rotary Joint which helps align the power generation system with the sun. The joint must provide structural support and controlled rotation to the outboard transverse booms as well as power and data transfer across the joint. The Solar Alpha Rotary Joint is composed of two transition sections and an integral, large diameter bearing. Alpha joint bearing design presents a particularly interesting problem because of its large size and need for high reliability, stiffness, and on orbit maintability. The discrete roller bearing developed is a novel refinement to cam follower technology. It offers thermal compensation and ease of on-orbit maintenance that are not found in conventional rolling element bearings. How the bearing design evolved is summarized. Driving requirements are reviewed, alternative concepts assessed, and the selected design is described.

Everman, Michael R.↗

Forced convection heat transfer to air/water vapor mixtures

Heat transfer coefficients were measured using both dry air and air/water vapor mixtures in the same forced convection cooling test rig (jet array impingement configurations) with mass ratios of water vapor to air up to 0.23. The primary objective was to verify by direct experiment that selected existing methods for evaluation of viscosity and thermal conductivity of air/water vapor mixtures could be used with confidence to predict heat transfer coefficients for such mixtures using as a basis heat transfer data for dry air only. The property evaluation methods deemed most appropriate require as a basis a measured property value at one mixture composition in addition to the property values for the pure components.

Richards, D. R.↗

Advanced technology for the Space Station

The goals and objectives of the Space Station Advanced Development Program are discussed. Data from tests and experiments in the areas of attitude control and stabilization, communications and tracking, data management systems, man systems, mechanisms, power systems, structures, thermal systems, and EVA are examined. The approaches used to implement these programs and for data transfer are described. The plans for the development of the Space Station are presented.

Nolan, Mark B.↗

Comparison of two procedures for predicting rocket engine nozzle performance

Two nozzle performance prediction procedures which are based on the standardized JANNAF methodology are presented and compared for four rocket engine nozzles. The first procedure required operator intercedence to transfer data between the individual performance programs. The second procedure is more automated in that all necessary programs are collected into a single computer code, thereby eliminating the need for data reformatting. Results from both procedures show similar trends but quantitative differences. Agreement was best in the predictions of specific impulse and local skin friction coefficient. Other compared quantities include characteristic velocity, thrust coefficient, thrust decrement, boundary layer displacement thickness, momentum thickness, and heat loss rate to the wall. Effects of wall temperature profile used as an input to the programs was investigated by running three wall temperature profiles. It was found that this change greatly affected the boundary layer displacement thickness and heat loss to the wall. The other quantities, however, were not drastically affected by the wall temperature profile change.

Davidian, Kenneth J.↗

Measurement of airfoil heat transfer coefficients on a turbine stage

A turbulence generating grid was designed and installed in the turbine inlet which produced the target nominal value of 10 percent free stream turbulence. Aerodynamic documentation of the rotor and stator midspan surface pressure distributions were obtained. Midspan heat transfer data were obtained on the rotor and stator for variations in inlet turbulence, rotor-stator axial spacing, and rotor incidence.

Dring, Robert P.↗

DATAC bus monitor

The Digital Autonomous Terminal Access Communications (DATAC) bus is a multiple transmitter data bus developed to interconnect various aircraft systems. A typical DATAC bus installation for the NASA B-737 aircraft is shown. A bus monitor unit was developed for the DATAC data bus. The bus monitor unit consists of two systems: A Zilog Z8002 based S100 bus microcomputer system that connects to a DATAC terminal and receives data appearing on the bus, and an IMB PC-compatible computer used to display and interpret that data. Test results of the existing bus monitor have indicated areas for improvement. The most obvious improvement is to increase the speed of the data transfers between the S100 and the MS-DOS systems.

Novacki, Stanley M., III↗

Reduced-gravity two-phase flow experiments in the NASA KC-135

An adequate understanding is sought of flow and heat transfer behavior in reduced and zero gravity conditions. Microgravity thermal-hydraulic analysis capabilities were developed for application to space nuclear power systems. A series of reduced gravity two phase flow experiments using the NASA KC-135 were performed. The objective was to supply basic thermal hydraulic information that could be used in development of analytical tools for design of space power systems. The experiments are described. Two main conclusions were drawn. First, the tests demonstrate that the KC-135 is a suitable test environment for obtaining two phase flow and heat transfer data in reduced gravity conditions. Second, the behavior of two phase flow in low gravity is sufficiently different from that obtained in 1 g to warrant intensive investigation of the phenomenon if adequate analytical tools are to be developed for microgravity conditions.

Cuta, Judith M.↗

Computational validation of a parabolized Navier-Stokes solver on a sharp-nose cone at hypersonic speeds

Perfect gas computational results from a newly-developed upwind, parabolized Navier-Stokes (PNS) solver are compared with an existing set of experimental laminar results for a 10-deg half-angle circular cone at freestream Mach number of 7.95. Comparisons were performed with surface pressure and heat transfer data, as well as with flowfield pitot measurements. The PNS code predicted the surface quantities accurately up through 20-deg angle-of-attack, including crossflow separation, and correctly defined the location of the bow shock and the edge of the boundary layer. The importance of cell Reynolds number, grid density, and thermal boundary conditions to the accurate prediction of the flowfield are examined through numerical emamples.

Huebner, Lawrence D.↗

Hyperswitch Network For Hypercube Computer

Data-driven dynamic switching enables high speed data transfer. Proposed hyperswitch network based on mixed static and dynamic topologies. Routing header modified in response to congestion or faults encountered as path established. Static topology meets requirement if nodes have switching elements that perform necessary routing header revisions dynamically. Hypercube topology now being implemented with switching element in each computer node aimed at designing very-richly-interconnected multicomputer system. Interconnection network connects great number of small computer nodes, using fixed hypercube topology, characterized by point-to-point links between nodes.

Chow, Edward↗

Design, fabrication and test of the RL10 derivative II chamber/primary nozzle

The design, fabrication and test of the RL10-II chamber/primary nozzle was accomplished as part of the RL10 Product Improvement Program (PIP). The overall goal of the RL10 PIP was to gain the knowledge and experience necessary to develop new cryogenic upper stage engines to fulfill future NASA requirements. The goal would be reached by producing an RL10 engine designed to be reusable, operate at several thrust levels, and have increased performance. The goals for the chamber/primary nozzle task were: (1) to design a reusable assembly capable of operation at increased mixture ratio and low thrust; (2) to fabricate three assemblies using new or updated techniques where possible; and (3) to test one assembly to verify the design and construction. The design and fabrication phases produced an assembly having improved features such as single piece reinforcing band segments (i.e., Mae West segments) and relocated tube exit braze joints (i.e., hooked tube exit). In addition, a computer program was developed to design the chamber tubes to meet both performance and heat transfer requirements. The test phase showed the specific impulse of the test bed engine system to be as predicted. These results, along with the heat transfer data obtained, sufficiently proved the overall design of the RL10-II recontoured and shortened chamber/primary nozzle assembly.

Marable, R. W.↗

Computer aided design environment for the analysis and design of multi-body flexible structures

A computer aided design environment consisting of the programs NASTRAN, TREETOPS and MATLAB is presented in this paper. With links for data transfer between these programs, the integrated design of multi-body flexible structures is significantly enhanced. The CAD environment is used to model the Space Shuttle/Pinhole Occulater Facility. Then a controller is designed and evaluated in the nonlinear time history sense. Recent enhancements and ongoing research to add more capabilities are also described.

Ramakrishnan, Jayant V.↗

Simulation of shuttle flight control system structural interaction with RMS deployed payloads

A simulation of the system made up of the Orbiter, Remote Manipulator System (RMS), and payload grappled by the RMS was completed. The simulation was used to study the stability of this overall system when its attitude is under control of the Orbiter's on-orbit Flight Control System (FCS). The simulation was also used to study the dynamics of the system when the RMS and its associated command software are in active control of the relative Orbiter to payload position and orientation. The simulation models all of the following elements: RMS boom bending (represented by two cubic bending models); RMS boom torsion; RMS joint gearbox compliance (represented by a non-linear wind-up model); flexibility at the RMS to Orbiter interface; flexibility at the RMS to payload interface; joint motor dynamics; joint servo-loop dynamics; RMS on-board computer command logic; data transfer delays between the RMS sensor and the RMS on-board computer and between the RMS on-board computer and RMS joint servos; on-orbit flight control nonlinear control logic; and the Reaction Control System (both Primary and Vernier) jet forces and moments.

Turnball, Joe↗

Surface flow and heating distributions on a cylinder in near wake of Aeroassist Flight Experiment (AFE) configuration at incidence in Mach 10 Air

Experimental heat transfer distributions and surface streamline directions are presented for a cylinder in the near wake of the Aeroassist Flight Experiment forebody configuration. Tests were conducted in air at a nominal free stream Mach number of 10, with post shock Reynolds numbers based on model base height of 6,450 to 50,770, and angles of attack of 5, 0, -5, and -10 degrees. Heat transfer data were obtained with thin film resistance gage and surface streamline directions by the oil flow technique. Comparisons between measured values and predicted values were made by using a Navier-Stokes computer code.

Wells, William L.↗

An electronic pressure profile display system for aeronautic test facilities

The NASA Lewis Research Center has installed an Electronic Pressure Profile Display system. This system provides for the real-time display of pressure readings on high resolution graphics monitors. The Electronic Pressure Profile Display system will replace manometer banks currently used in aeronautic test facilities. The Electronic Pressure Profile Display system consists of an industrial type Digital Pressure Transmitter (DPT) unit which interfaces with a host computer. The host computer collects the pressure data from the DPT unit, converts it into engineering units, and displays the readings on a high resolution graphics monitor in bar graph format. Software was developed to accomplish the above tasks and also draw facility diagrams as background information on the displays. Data transfer between host computer and DPT unit is done with serial communications. Up to 64 channels are displayed with one second update time. This paper describes the system configuration, its features, and its advantages over existing systems.

Woike, Mark R.↗