Search NASA⌕ Search

SEARCH · Search NASA

Results for “failure analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Modelling of High-Chromia Refractory Spalling in Slagging Coal Gasifiers

The economic viability of converting coal into clean burning liquid fuels in slagging coal gasifiers is compromised by the limited service lifetime of hot-face refractories. One of the most severe refractory degradation mechanisms is spalling, which can occur by either volume expansion phenomena (compressive stresses) or by volume shrinkage phenomena (tensile stresses). A volume shrinkage model is benchmarked to high-chromia refractory material properties and performance under gasifier operating conditions. The model is found to be appropriate for first order estimates of gasifier refractory lifetime when the apparent diffusivity of volatized Cr in the refractory includes the effects of slag-filled pores and cracks.

Failure Analysis↗

Enhancing building resilience in cold climates: Integrating heat pump technologies with renewable energy

As electrification advances and Cold Climate Heat Pump technology progresses, ensuring grid stability becomes increasingly critical for effective heating in cold climates. However, natural disasters, especially during winter, pose significant threats to grid stability, impacting the reliability of air-source heat pumps. Despite these challenges, the integration of renewable energy sources and storage solutions in heating systems has not been extensively studied within the context of resilience. Here, this paper delves into the literature on renewable-powered heat pumps to assess their potential in enhancing building resilience in U.S. cold climate zones, which are particularly susceptible to extreme weather and grid disruptions. By leveraging renewable sources—solar, geothermal, and water—in conjunction with heat pump technology and supported by thermal or battery storage, this approach aims to provide a dependable solution for maintaining indoor heating during grid failures. Our analysis begins with a review of various renewable energy sources suitable for heat pumps, followed by an exploration of their application in cold climate regions across the U.S., and discussions on potential integration strategies with heat pump systems. This study highlights the advantages and suitability of solar irradiance and geothermal resources, emphasizing the importance of tailored, site-specific assessments to maximize energy efficiency and resilience. Additionally, it outlines the economic and environmental considerations necessary for implementing such systems and identifies potential challenges and areas for future research to facilitate the broader integration of renewable energy in heating solutions for enhanced resilience.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Analysis of microstructural facet fatigue failure in ultra-fine grained powder metallurgy Ti-6Al-4V produced through hydrogen sintering

The hydrogen sintering and phase transformation (HSPT) process is a powder metallurgy method that produces Ti-6Al-4V with fatigue properties rivaling wrought processed Ti-6Al-4V. Previous fatigue work on HSPT Ti-6Al-4V has shown failure to be frequently caused by microstructural facets, which were believed to be grain boundary (GB) α phase. This belief conflicts with other reports as fatigue failure typically occurs across α colonies or primary α grains, not GB α. In this work, electron backscattered diffraction is used to identify these facets as GB α. Furthermore, a simple geometric model predicting the effective slip length of GB α is presented.

36 MATERIALS SCIENCE↗

Regional Nodal Recurrence After Breast Conservation Treatment With Radiotherapy for Women With Early-Stage Breast Carcinoma

Purpose: To report the long-term outcomes for women presenting with regional lymph node recurrence after breast conservation treatment with radiotherapy for Stage I and II invasive breast carcinoma. Methods and Materials: Of the women with pathologic Stage I and II invasive breast carcinoma treated with breast conservation treatment at University of Pennsylvania, 29 developed regional nodal recurrence as their first site of failure. An analysis of the patterns of regional nodal recurrence and their prognosis after recurrence was undertaken. The median follow-up from regional nodal recurrence was 5.4 years. Results: The pattern of regional nodal recurrence was as follows: 14 (48%) with simultaneous local and axillary recurrence, 7 (24%) with recurrence in the axilla only, 5 (17%) with recurrence in the supraclavicular region only, and 3 (10%) with multiple nodal sites of recurrence. For the entire study group, the 5-, 10-, and 15-year overall survival rate was 70%, 37%, and 28%, respectively. The 10-year overall survival rate for patients with locoregional recurrence was 32% compared with 45% for patients with regional-only recurrence (p = 0.50). The 10-year overall survival rate for patients with axillary recurrence discovered on pathologic examination of the mastectomy specimen was 31% compared with 42% for patients with palpable regional lymphadenopathy (p = 0.83). Conclusion: Patients with regional nodal recurrence after breast conservation treatment with radiotherapy for early-stage breast carcinoma are potentially salvageable. The prognosis after regional nodal recurrence was not significantly different when stratified by the presence or absence of simultaneous in-breast recurrence or the method of detection.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Failure evaluation of neutron-irradiated SiC/SiC composites by underwater acoustic emission

Here, understanding the statistical properties of mechanical properties of non-irradiated and neutron-irradiated SiC/SiC composites is essential for component design. This study aims to evaluate the detailed damage accumulation behavior of composites focusing on two fracture parameters: proportional limit stress (PLS) and acoustic emission (AE) onset stress. The developmental underwater AE technique, which is benefit in non-contact in-situ failure monitoring method during mechanical testing and in handle of the irradiated material, was first applied to evaluate damage accumulation behavior. Two types of chemical vapor infiltration SiC/SiC composites were used: one reinforced with Hi-Nicalon Type-S SiC fiber and one reinforced with Tyranno-SA3 SiC fiber in the form of satin-woven 2D fabrics with pyrolytic carbon interface. Neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory reached a fluence of 30 dpa at a temperature of 620–670°C. Four-point flexural tests were conducted to evaluate post-irradiation strength. Weibull statistics did not suggest marked degradation of composite strength. Detailed failure behavior evaluated by AE demonstrated no irradiation-induced change of the AE onset stress (i.e., crack initiation equivalent stress). Failure probability analysis suggests that increasing the reliability of composites (i.e., the Weibull modulus rather than strength itself) is essential to expanding the design margin and benefiting from a probabilistic design approach.

36 MATERIALS SCIENCE↗

An implantable biomechanical energy harvester for animal monitoring devices

Insufficient service life and the resulting need for battery replacements have been a great challenge for implantable electronic devices. This is particularly true for animal tracking applications, because recapturing animals is often unlikely once they are released to the wild. To tackle this problem, we developed a biomechanical energy harvester that uses a Macro Fiber Composite™ (MFC) piezoelectric beam to harvest the mechanical energy from animals’ body bending movements as the power source for implantable and wearable devices. Prototypes of an underwater acoustic transmitter using this technology were subdermally implanted into juvenile white sturgeon and their energy harvesting performance was evaluated through the device’s transmissions. Additionally, the fish successfully recovered from the implantation surgery and freely swam inside a tank. The transmitter prototypes in the fish continually transmitted signals for a period up to 5 weeks. A benchtop test setup was also created to emulate the fish’s body bending, estimate the device’s energy harvesting performance in the live fish, and perform accelerated fatigue testing of the energy harvester by applying test parameters learned from a video study of the fish’s body movement and behavior characteristics. The gradual depolarization of the piezoelectric ceramic material in the MFC under cyclic mechanical loading was the main limiting factor for the life span of the energy harvester. Pathways for improvement are proposed to achieve long-term efficacy of powering implantable and wearable electronic devices.

42 ENGINEERING↗

Computational modeling of graphite degradation in molten salt reactors: Role of infiltration

Molten salt reactors (MSRs) often employ graphite as a moderator and reflector. An important challenge for deploying graphite in these reactors is that, due to limited experimental data, our understanding of graphite’s structural integrity in molten salt environments remains incomplete. Here, this study addresses heat generation from fuel-bearing salt that has infiltrated open pores in the graphite, driven primarily by pressure differentials. This is one of multiple identified physical and chemical mechanisms through which molten salt could potentially degrade graphite. Thermally driven stresses are quantified using the Molten-Salt Reactor Experiment (MSRE) graphite moderator elements as a case study. Finite element simulations predict stress distributions at varying infiltration levels, indicating that thermal stresses increase with higher infiltration. Rare-event simulations using the parallel subset simulation framework identify the combinations and corresponding ranges of input parameters that lead to stresses above a specified threshold. In particular, combinations involving high infiltration amounts, high power density, and low thermal conductivity tend to induce the highest stresses. Under the inputs and assumptions considered in this work, the magnitudes of the thermally driven stresses are quite low, with a very low likelihood of causing failure due to exceeding the graphite’s tensile strength. Additionally, rare-event simulations were performed for two more scenarios: a scaled-up moderator geometry and a localized hotspot in the original geometry. Both cases resulted in increased susceptibility to failure, though not to a detrimental extent. Furthermore, the combined effects of irradiation and infiltration-induced thermal stresses were evaluated. The results showed that thermal stresses from infiltration were negligible compared to those caused by irradiation. The findings of such a study are inherently component-specific, but the methodology presented here could be used for similar assessments of salt-infiltration effects in other graphite components.

36 - MATERIALS SCIENCE↗

Material Characterization-Based Wear Mechanism Investigation for Biomass Hammer Mills

Biomass, as harvested, is composed of inorganic compounds both intrinsically and extrinsically and can be abrasive. The present study investigates the wear modes and mechanisms of two types of blades of hammer mills used in biomass size reduction (impacting the particle size and distribution) and densification (impacting the size, shape, and density). The dominant wear modes for the stage 1 steel blades are determined to be erosive and polishing wear. For the stage 2 blades with a carbide weld overlay, the main wear mechanisms are erosion and fracture. Partial replacement of Co by Fe in the outer layer of the carbide grits, likely induced by diffusion during high-temperature welding, has been correlated to the observed microcracking. Finally, the microcracking is believed to weaken the grit strength and fracture toughness to make the overlay prone to fracture and erosion due to repetitive contact with the inorganic contents in chopping biomass.

42 ENGINEERING↗

Training the Recurrent neural network by the Fuzzy Min-Max algorithm for fault prediction

In this paper, we present a training technique of a Recurrent Radial Basis Function neural network for fault prediction. We use the Fuzzy Min-Max technique to initialize the k-center of the RRBF neural network. The k-means algorithm is then applied to calculate the centers that minimize the mean square error of the prediction task. The performances of the k-means algorithm are then boosted by the Fuzzy Min-Max technique.

97 MATHEMATICS AND COMPUTING↗

Spall response of single-crystal copper

We performed a series of systematic spall experiments on single-crystal copper in an effort to determine and isolate the effects of crystal orientation, peak stress, and unloading strain rate on the tensile spall strength. Strain rates ranging from 0.62 to 2.2 × 10 6 s -1 and peak shock stresses in the 5–14 GPa range, with one additional experiment near 50 GPa, were explored as part of this work. Gun-driven impactors, called flyer plates, generated flat top shocks followed by spall. This work highlights the effect of crystal anisotropy on the spall strength by showing that the spall strength decreases in the following order: [100], [110], and [111]. Over the range of stresses and strain rates explored, the spall strength of [100] copper depends strongly on both the strain rate and shock stress. Except at the very highest shock stress, the results for the [100] orientation show linear relationships between the spall strength and both the applied compressive stress and the strain rate. In addition, hydrodynamic computer code simulations of the spall experiments were performed to calculate the relationship between the strain rate near the spall plane in the target and the rate of free surface velocity release during the pullback. As expected, strain rates at the spall plane are much higher than the strain rates estimated from the free surface velocity release rate. We have begun soft recovery experiments and molecular dynamics calculations to understand the unusual recompression observed in the spall signature for [100] crystals.

36 MATERIALS SCIENCE↗

A continuum damage approach to spallation and the role of microinertia

Spall failure is of interest due to its prevalence in high strain rate problems in which the spallation is driven by the interaction of release waves. In this article, a porosity-based damage model that includes microinertial effects is used to examine spall failure. The model is successfully calibrated to plate impact-driven experiments and then used to evaluate experimental conditions producing more extreme strain rate conditions, such as those in laser-driven experiments. The incorporation of microinertia allows us to better understand the increase in apparent macroscopic spall strength seen at high strain rates. Correspondingly, we conclude that the incorporation of microinertial effects improves the model’s predictive capabilities. Microinertial effects result in more severe local tensile stresses that affect the damage evolution, and microinertia can play a significant role in the approach to the material’s ideal strength at extreme loading rates. Additionally, a preliminary parametric study is also carried out to investigate the role of microstructural aspects such as nucleation volume fraction and initial pore radius. One counter-intuitive result from the microinertial effects is that, for a given nucleation site volume fraction, having larger initial pore nucleation sites can lead to an improved macroscopic spall strength.

36 MATERIALS SCIENCE↗

Effect of grain size on damage and failure in two-phase materials: Homogenized CuPb

It is well known that spall failure strongly depends on the microstructure of a material. There have been numerous studies to study the effect of grain size on the overall spall strength and the total amount of damage in single element metals like copper. However, such systematic studies remain rare in two-phase materials and alloys. In this work, two incipient spall experiments were performed on a Cu–1%Pb alloy to understand the effect of grain size on the damage and failure in a two-phase material. Overall, these results showed that even though the spall strength did not change as a function of grain size, there were significant differences in the total amount of damage as a function of grain size. A clear increase in the total damage present in the material was seen as the grain size was increased from 32 to either 70 or 75 μm in either of the experiments. Furthermore, this difference was attributed to variations in the void growth rate as the grain size was increased.

36 MATERIALS SCIENCE↗

The influence of pearlite fraction on the shock properties of ferrite–pearlite steel microstructures: Insight into the effect of second-phase particles

Here, the goal of this work is to investigate the effect of varying phase fractions on the overall spall strength and damage behavior of a material. Specifically, two plain carbon, ferrite–pearlite steels (1045 and A283) were subjected to spall recovery experiments to investigate the effect of pearlite fraction on spall strength and total damage. The A283 (20% pearlite) alloy exhibited a higher Hugoniot elastic limit and spall strength compared with 1045 (60% pearlite). Discontinuous and continuous yielding behaviors were observed at quasi-static and dynamic rates for A283 and 1045, respectively. The yielding behavior was connected to pearlite fraction and the prevalence of dislocation-emitting, ferrite/cementite interfaces. Postmortem characterization revealed cementite lamellae cracking within pearlite of 1045, suggesting that pearlite reduces spall strength by providing low-energy damage nucleation sites. The rate of damage growth and coalescence was similar between the two alloys; however, 1045 exhibited more continuous cracks than A283, which exhibited a greater prevalence of discrete voids.

36 MATERIALS SCIENCE↗

Effect of surface defects on damage and failure of dynamically driven cylindrical shells

Here, in this work, expanding cylinder experiments are performed using a gas gun on the aluminum 6061 alloy to understand the dynamic deformation and failure behavior of this material in the presence of surface defects in the form of scratches. The experiments are then modeled with the modified Tepla (for tensile plasticity) model, which is equipped with the damage yield function of Gurson [“Continuum theory of ductile rupture by void nucleation and growth: Part I—Yield criteria and flow rules for porous ductile media,” (1977)] and Tvergaard and Needleman [Acta Metall. 32(1), 157–169 (1984)], over-stress viscosity [F. Addessio and J. Johnson, J. Appl. Phys. 74(3), 1640–1648 (1993)], and the underlying viscoplastic model of Preston et al. [J. Appl. Phys. 93(1), 211–220 (2003)] (Preston–Tonks–Wallace model) for the dense material. The Tepla model parameters were calibrated using the Bayesian approach against experimentally measured free-surface velocity data obtained from plate impact experiments on the aluminum 6061 alloy. The evolution of radial expansion and shapes of the deformed cylinder from the simulations on a pristine cylinder wall and a cylinder wall with a longitudinal surface defect shows excellent agreement with the corresponding experimental results. Finally, the role of surface defect size and cylinder wall geometry on the dynamic strength of the cylinder wall was also investigated through a series of simulations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗