Search NASA⌕ Search

SEARCH · Search NASA

Results for “power engineering computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Jet impingement heat transfer enhancement for the GPU-3 Stirling engine

A computer model of the combustion-gas-side heat transfer was developed to predict the effects of a jet impingement system and the possible range of improvements available. Using low temperature (315 C (600 F)) pretest data in an updated model, a high temperature silicon carbide jet impingement heat transfer system was designed and fabricated. The system model predicted that at the theoretical maximum limit, jet impingement enhanced heat transfer can: (1) reduce the flame temperature by 275 C (500 F); (2) reduce the exhaust temperature by 110 C (200 F); and (3) increase the overall heat into the working fluid by 10%, all for an increase in required pumping power of less than 0.5% of the engine power output. Initial tests on the GPU-3 Stirling engine at NASA-Lewis demonstrated that the jet impingement system increased the engine output power and efficiency by 5% - 8% with no measurable increase in pumping power. The overall heat transfer coefficient was increased by 65% for the maximum power point of the tests.

Johnson, D. C.↗

Estimating the carbon footprint of computational fluid dynamics

In this study, computational resources have grown exponentially in the past few decades. These machines make possible research and design in fields as diverse as medicine, astronomy, and engineering. Despite ever-increasing computational capabilities, direct simulation of complex systems has remained challenging owing to the degrees of freedom involved. At the cusp of exascale computing, high-resolution simulation of practical problems with minimal model assumptions may soon experience a renaissance. However, growing reliance on modern computers comes at the cost of a growing carbon footprint. To illustrate this, we examine historic computations in fluid dynamics where larger computers have afforded the opportunity to simulate flows at increasingly relevant Reynolds numbers. Under a variety of flow configurations, the carbon footprint of such simulations is found to scale roughly with the fourth power of Reynolds number. This is primarily explained by the computation cost in core-hours, which is also described by similar scaling, though regional differences in renewable energy use also play a role. Using the established correlation, we examine a large database of simulations to develop estimates for the carbon footprint of computational fluid dynamics in a given year. Collectively, the analysis provides an additional benchmark for new computations where, in addition to balancing considerations of model fidelity, carbon footprint should also be considered.

42 ENGINEERING↗

ParaStell: parametric modeling and neutronics support for stellarator fusion power plants

The three-dimensional variation inherent to stellarator geometries and fusion sources motivates three-dimensional modeling to obtain accurate results from computational modeling in support of design and analysis of first wall, blanket, and shield (FWBS) systems. Manually constructing stellarator fusion power plant geometries in computer-aided design (CAD) and defining the corresponding fusion source can be cumbersome and challenging. The open-source parametric modeling toolset ParaStell has been developed to automate construction of such geometries in low-fidelity. Low-fidelity modeling is useful during the conceptual phase of engineering design as a means of rapidly exploring the design space of a given device. The modeling capability of ParaStell includes in-vessel components and magnets, for any given stellarator configuration, using a parametric definition and plasma equilibrium data. Furthermore, the toolset automates the generation of detailed, tetrahedral neutron source definitions and DAGMC geometries for use in neutronics modeling. ParaStell assists rapid design iteration, parametric study, and design optimization of stellarator fusion cores. As a demonstration of the design iteration capability, the effect of the three-dimensional parameter space on tritium breeding and magnet shielding is investigated, using the WISTELL-D configuration as a design basis. Blanket and shield thicknesses are varied in three dimensions, using the space available between the plasma edge and magnet coils as a constraint. The corresponding effects on tritium breeding ratio and magnet heating are tallied using the open-source Monte Carlo particle transport code OpenMC. The inclusion of additional and higher-fidelity modeling capabilities is planned for ParaStell’s future, as well as its implementation in machine-driven optimization.

Moreno, Connor↗

Design and development of a ceramic radial turbine for the AGT101

An acceptable and feasible ceramic turbine wheel design has been achieved, and the relevant temperature, stress, and success probability analyses are discussed. The design is described, the materials selection presented, and the engine cycle conditions analysis parameters shown. Measured MOR four-point strengths are indicated for room and elevated temperatures, and engine conditions are analyzed for various cycle states, materials, power states, turbine inlet temperatures, and speeds. An advanced gas turbine ceramic turbine rotor thermal and stress model is developed, and cumulative probability of survival is shown for first and third-year properties of SiC and Si3N4 rotors under different operating conditions, computed for both blade and hub regions. Temperature and stress distributions for steady-state and worst-case shutdown transients are depicted.

Finger, D. G.↗

Integrated flight/propulsion control system architectures for a high speed aircraft

The present investigation is concerned with the impact of integrated flight, inlet, and engine control system architectures on system effectiveness and life cycle cost (LCC). The aircraft employed in the investigation is a modified YF-12 with a cruise Mach number of 2.5. The aircraft has two advanced technology aircraft JT-69 afterburning, low-bypass turbofan engines. Advanced technologies suitable for use in future flight/propulsion control systems are related to distributed computer networks, fault tolerant computers and software, analytical redundancy, self-checking microprocessor pairs, advanced direct drive actuators, fiber optic data buses, VLSI microcircuits, and skewed sensors. The integrated architectures were found to have fewer sensors, actuators, and power sources than the nonintegrated architectures.

Bangert, L. H.↗

Aerodynamics of powered missile separation from F/A-18 aircraft

A 3D dynamic 'chimera' algorithm that solves the thin-layer Navier-Stokes equations over multiple moving bodies was modified to numerically simulate the aerodynamics, missile dynamics, and missile plume interactions of a missile separating from a generic wing and from an F/A-18 aircraft in transonic flow. The missile is mounted below the wing for missile separation from the wing and on the F/A-18 fuselage at the engine inlet side for missile separation from aircraft. Static and powered missile separation cases are considered to examine the influence of the missile and plume on the wing and F/A-18 fuselage and engine inlet. The aircraft and missile are at two degrees angle of attack, Reynolds number of 10 million, freestream Mach number of 1.05 and plume Mach number of 3.0. The computational results show the details of the flow field.

Ahmad, J. U.↗

Structural Mechanics and Dynamics Branch

The 2002 annual report of the Structural Mechanics and Dynamics Branch reflects the majority of the work performed by the branch staff during the 2002 calendar year. Its purpose is to give a brief review of the branch s technical accomplishments. The Structural Mechanics and Dynamics Branch develops innovative computational tools, benchmark experimental data, and solutions to long-term barrier problems in the areas of propulsion aeroelasticity, active and passive damping, engine vibration control, rotor dynamics, magnetic suspension, structural mechanics, probabilistics, smart structures, engine system dynamics, and engine containment. Furthermore, the branch is developing a compact, nonpolluting, bearingless electric machine with electric power supplied by fuel cells for future "more electric" aircraft. An ultra-high-power-density machine that can generate projected power densities of 50 hp/lb or more, in comparison to conventional electric machines, which generate usually 0.2 hp/lb, is under development for application to electric drives for propulsive fans or propellers. In the future, propulsion and power systems will need to be lighter, to operate at higher temperatures, and to be more reliable in order to achieve higher performance and economic viability. The Structural Mechanics and Dynamics Branch is working to achieve these complex, challenging goals.

Stefko, George↗

High-Temperature Probe Station Developed to Characterize Microwave Devices Through 500 C

A photograph and a block diagram of the high-temperature probe station are shown. The system consists of the ceramic heater mounted on a NASA shuttle tile insulator, a direct current power supply, a personal-computer-based data acquisition and temperature controller, microwave probes, a microscope, and a network analyzer. The ability to perform microwave tests at high temperatures is becoming necessary. There is now a need for sensors and communication circuits that can operate at 500 C and above for aircraft engine development and monitoring during flight. To address this need, researchers have fabricated devices using wide bandgap semiconductors such as SiC with targeted operating temperatures of 500 to 600 C. However, the microwave properties of these devices often change drastically with temperature, so any designs that are intended to be used in such an environment must be characterized at high temperatures. For some reliability, lifetime, and direct-current testing, the device under test can be packaged and characterized in an oven. However, for RF and microwave measurements, it is usually not possible to establish a calibrated reference plane at the device terminals within a package. In addition, the characteristics of the package would vary over a 500 C temperature range, and this would have to be accounted for when the data were analyzed. A high temperature probe station allows circuits and devices to be characterized through on wafer measurements across a broad temperature range with known reference plane. The conventional, commercially available thermal wafer-probe stations that are used to evaluate microwave devices across a controlled temperature range have a typical upper limit of 200 C. Standalone thermal heating chucks are available with an extended upper temperature range of 300 to 400 C. To effectively characterize devices at temperatures up to and surpassing 500 C, Glenn researchers developed a custom probe station. In the past, custom probe stations have been developed to test devices under other extreme environments, such as cryogenic temperatures as low as 37 K. Similarly, this custom probe station was specifically modified for high-temperature use. It allows devices to be measured quickly and flexibly, without the use of wire bonds and test fixtures. The probe station is shown making scattering parameter measurements from 1 to 50 GHz with a Hewlett-Packard 8510C Network Analyzer. There is a half-wafer of silicon directly on top of the heater to provide a uniform heated platform for our sample. A quarter wafer of silicon carbide forms the substrate for our test circuit of several transmission lines.

Downey, Alan N.↗

Simulations of NOx Emissions from Low Emissions Discrete Jet Injector Combustor Tests

An experimental and computational study was conducted to evaluate the performance and emissions characteristics of a candidate Lean Direct Injection (LDI) combustor configuration with a mix of simplex and airblast injectors. The National Combustion Code (NCC) was used to predict the experimentally measured EINOx emissions for test conditions representing low power, medium power, and high-power engine cycle conditions. Of the six cases modeled with the NCC using a reduced-kinetics finite-rate mechanism and lagrangian spray modeling, reasonable predictions of combustor exit temperature and EINOx were obtained at two high-power cycle conditions.

Ajmani, Kumud↗

GLC_Exec v. 1.2.1

Launching a rocket involves a controlled transition of the rocket subsystems from a quiescent state to the launch state (i.e., lift-off). In order to launch safely, with confidence that the rocket will successfully complete its mission, the state-of-health for all rocket subsystems and critical ground support equipment must be closely monitored throughout the launch process. This is accomplished by the ground support engineers using mission-specific ground support equipment. A subset of the GSE, the Remote Electrical Ground Interface System (REGIS), is located nearest the rocket to which it's connected via the Umbilical, a wiring harness providing power, sensor, and control lines. The REGIS also connects via Ethernet to the Ground Launch Computer (GLC).

Kilgore, Roger Martin↗

Modified versions of the fuel performance codes RTOP and RTOP-CA

RTOP code predicts thermal and mechanical behavior of LWR fuel rods and release of GFPs both in normal stationary and transient operation modes, and transient power ramps, specific to the reactivity-initiated accidents (RIA). Computational domains of the code include fuel column, zirconium cladding, gas under cladding, and fuel microstructure - UO{sub 2} grain and the development of gaseous porosity of different origin during irradiation. RTOP-CA code is based on the RTOP code. It simulates the behavior of a fuel rod with cladding rupture opening and RFPs release into the primary coolant circuit in normal operation modes. The paper presents the results of development and validation of engineering models, which take into account characteristics of the neutron spectrum during the fuel cycle and are integrated into modernized versions of the fuel performance codes RTOP and RTOP-CA. The paper focuses on the detailed description of two models. Four-group neutron-physical engineering model describes burn-out of gadolinium isotopes and calculates spatial power profile in a Gd-doped fuel rod pellet. The second engineering model presented is developed for fast estimation of fuel burnup in case of fuel rod cladding leakage accident. The comparison of the present calculations with the results of calculations by neutron codes shows that the model describes the heat rate distribution and the gadolinium burn-out with sufficient accuracy. The code also calculates the LHR of Gd-doped fuel rods given the heat rate of the adjacent UO{sub 2} fuel rods. This work allows determining the histories of LHR for the Gd-doped fuel rod from the average LHR of FA for various equilibrium WWER fuel cycles, power units and fuel enrichments. The presented model is implemented in the RTOP fuel performance code to calculate the thermomechanical behavior of the fuel rods. An engineering-physical model is developed for fast estimation of {sup 134}Cs/{sup 137}Cs activity ratio in fuel taking into account the parameters of the neutron spectrum during the fuel cycle. Implementation of the model enables to increase the reliability of correct fuel burnup determination in a failed fuel assembly (FA)based on the FERDS activity measurements during reactor operation. Results of the model calculations obtained for the FAs with a higher fuel enrichment and the NPP activity measurements have shown a higher {sup 134}Cs/{sup 137}Cs activity ratio compared to the values for the fuel with enrichment up to 3.6 wt. % in {sup 235}U. Currently, the engineering model is applicable within the range of UO{sub 2} enrichment from 3 to 5 wt. % in {sup 235}U, and Gd{sub 2}O{sub 3} enrichment from 5 to 8 wt. %.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multiphysics analysis of liquid metal annular linear induction pumps: A project overview

Liquid metal-cooled fission reactors are both moderated and cooled by a liquid metal solution. These reactors are typically very compact and they can be used in regular electric power production, for naval and space propulsion systems or in fission surface power systems for planetary exploration. The coupling between the electromagnetics and thermo-fluid mechanical phenomena observed in liquid metal thermo-magnetic systems for nuclear and space applications gives rise to complex engineering magnetohydrodynamics and numerical problems. It is known that electromagnetic pumps have a number of advantages over rotating mechanisms: absence of moving parts, low noise and vibration level, simplicity of flow rate regulation, easy maintenance and so on. However, while developing annular linear induction pumps, we are faced with a significant problem of magnetohydrodynamic instability arising in the device. The complex flow behavior in this type of devices includes a time-varying Lorentz force and pressure pulsation due to the time-varying electromagnetic fields and the induced convective currents that originates from the liquid metal flow, leading to instability problems along the device geometry. The determinations of the geometry and electrical configuration of liquid metal thermo-magnetic devices give rise to a complex inverse magnetohydrodynamic field problem were techniques for global optimization should be used, magnetohydrodynamics instabilities understood –or quantified- and multiphysics models developed and analyzed. Lastly, we present a project overview as well as a few computational models developed to study liquid metal annular linear induction pumps using first principles and the a few results of our multi-physics analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dynamic Loads Generation for Multi-Point Vibration Excitation Problems

A random-force method has been developed to predict dynamic loads produced by rocket-engine random vibrations for new rocket-engine designs. The method develops random forces at multiple excitation points based on random vibration environments scaled from accelerometer data obtained during hot-fire tests of existing rocket engines. This random-force method applies random forces to the model and creates expected dynamic response in a manner that simulates the way the operating engine applies self-generated random vibration forces (random pressure acting on an area) with the resulting responses that we measure with accelerometers. This innovation includes the methodology (implementation sequence), the computer code, two methods to generate the random-force vibration spectra, and two methods to reduce some of the inherent conservatism in the dynamic loads. This methodology would be implemented to generate the random-force spectra at excitation nodes without requiring the use of artificial boundary conditions in a finite element model. More accurate random dynamic loads than those predicted by current industry methods can then be generated using the random force spectra. The scaling method used to develop the initial power spectral density (PSD) environments for deriving the random forces for the rocket engine case is based on the Barrett Criteria developed at Marshall Space Flight Center in 1963. This invention approach can be applied in the aerospace, automotive, and other industries to obtain reliable dynamic loads and responses from a finite element model for any structure subject to multipoint random vibration excitations.

Shen, Lawrence↗

Short-term apartment-level load forecasting using a modified neural network with selected auto-regressive features

Residential electricity load profiles and their diversity have become increasingly important to realize the benefits of Smart or Transactive Energy Networks (TENs). An important element of TENs will be practical, accurate, and implementable residential load forecasting techniques. While there have been many approaches to short-term load forecasting, few have included forecasting for individual households, partly because the high volatility and idiosyncrasies present in individual household load data can pose significant challenges. In this study, we develop a Convolutional Long Short-Term Memory-based neural network with Selected Autoregressive Features (termed a CLSAF model) to improve short-term household electricity load forecasting accuracy by employing three strategies: autoregressive features selection, exogenous features selection, and a “default” state to avoid overfitting at times of high load volatility. We include aggregations of apartments to floor and building level, because utilities may favor transactive approaches that rely on aggregator models, e.g., a cluster of consumers as opposed to an individual. We demonstrate that the CLSAF model, by virtue of its enhanced feature representation and modest computational resources, can accomplish load forecasting in a multi-family residential building across three spatial granularities (individual apartment/household, floor, and building levels), with an accuracy improvement of up to 25% compared to a persistence model. We propose a data screening technique to characterize time-series electricity-load data. This technique is suitable for integration into a TEN ecosystem and allows one to estimate confidence levels of the load forecasts to optimize computational resources and the risks associated with uncertain forecasts.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Effect of NLTE Emissivity Models on NIF Ignition Hohlraum Power Requirements

NLTE atomic physics model can significantly affect the power requirements and plasma conditions in ignition hohlraums. This is because the emissivity is a significant factor in determining the time dependent coronal temperature of the hot blow-off plasma filling ignition hohlraums, which, in turn, determines the total energy stored in that coronal plasma at any instant. Here we present best estimates of NLTE emissivity using the SCRAM model, including the range of uncertainty, and compare them with the emissivity of the model used to design NIF ignition hohlraums and set the NIF pulse shape, XSN NLTE. We then present pulse shapes derived from hohlraum simulations using an atomic physics model that approximates the SCRAM emissivities. We discuss the differences in coronal energetics and show how this affects the pulse shape and, in particular, the peak power requirement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Superhigh-speed electric motors

Superhigh-speed electric motors, with rotor speed up to 500000 rpm and power up to 100 W, are of interest for surface micromachining. A mathematical model of such motors is developed by means of Ansys Maxwell software. The motors are experimentally studied.

42 ENGINEERING↗