Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface layering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Acceleration and guiding of fast electrons by a nanobrush target

Laser interaction with a nanobrush target plasma is investigated at the SILEX-I laser facility [X. F. Wei et al., J. Phys. Conf. Ser. 112, 032010 (2008)] with a laser of intensity 7.9x10{sup 18} W/cm{sup 2}. Highly collimated fast electron beams with yields of more than three times higher than that from the planar target can be produced. Two-dimensional particle-in-cell simulation confirms that a layered surface structure can increase the efficiency of laser energy absorption, and the resulting fast electrons are tightly collimated and guided by the plasma layers to a cross section of about the laser spot size.

43 PARTICLE ACCELERATORS↗

XPS analysis of the effect of fillers on PTFE transfer film development in sliding contacts

The development of transfer films atop steel counterfaces in contact with unfilled and bronze-filled PTFE has been studied using X-ray photoelectron spectroscopy. The sliding apparatus was contained within the vacuum of the analytical system, so the effects of the native oxide, hydrocarbon, and adsorbed gaseous surface layers of the steel upon the PTFE transfer behavior could be studied in situ. For both the filled and the unfilled PTFE, cleaner surfaces promoted greater amounts of transfer. Metal fluorides, which formed at the transfer film/counterface interface, were found solely in cases where the native oxide had been removed to expose the metallic surface prior to sliding. These fluorides also were found at clean metal/PTFE interfaces formed in the absence of frictional contact. A fraction of these fluorides resulted from irradiation damage inherent in XPS analysis. PTFE transfer films were found to build up with repeated sliding passes, by a process in which strands of transfer filled in the remaining counterface area. Under these reported test conditions, the transfer process is not expected to continue atop previously deposited transfer films. The bronze-filled composite generated greater amounts of transfer than the unfilled PTFE. The results are discussed relative to the observed increase in wear resistance imparted to PTFE by a broad range of inorganic fillers.

Blanchet, T. A.↗

Northern and Southern Permafrost Regions on Mars with High Content of Water Ice: Similarities and Differences

The measurements by neutron detectors on Odyssey have revealed two large poleward regions with large depression of flux of epithermal and high energy neutrons [1-3]. The flux of neutrons from Mars is known to be produced by the bombardment of the surface layer by galactic cosmic rays. The leakage flux of epithermal and fast neutrons has regional variation by a factor of 10 over the surface of Mars (e.g. see [3- 5]). These variations are mainly produced by variations of hydrogen content in the shallow subsurface. On Mars hydrogen is associated with water. Therefore, the Northern and Southern depressions of neutron emission could be identified as permafrost regions with very high content of water ice [1-5]. These regions are much larger than the residual polar caps, and could contain the major fraction of subsurface water ice. Here we present the results of HEND neutron data deconvolution for these regions and describe the similarities and differences between them.

Mitrofanov, I. G.↗

Northern and Southern Permafrost Regions on Mars with High Content of Water Ice: Similarities and Differences

The measurements by neutron detectors on Odyssey have revealed two large poleward regions with large depression of flux of epithermal and high energy neutrons. The flux of neutrons from Mars is known to be produced by the bombardment of the surface layer by galactic cosmic rays. The leakage flux of epithermal and fast neutrons has regional variation by a factor of 10 over the surface of Mars. These variations are mainly produced by variations of hydrogen content in the shallow subsurface. On Mars hydrogen is associated with water. Therefore, the Northern and Southern depressions of neutron emission could be identified as permafrost regions with very high content of water ice. These regions are much larger than the residual polar caps, and could contain the major fraction of subsurface water ice. Here we present the results of HEND neutron data deconvolution for these regions and describe the similarities and differences between them.

Mitrofanov, I. G.↗

Initial analysis of “stone” size Ryugu samples: current status

As a part of the initial analysis of the Ryugu samples, we perform a variety of analyses of millimeter-sized "stones". Our goals are to elucidate the entire formation process of C-type asteroid Ryugu from the viewpoint of petrology and mineralogy ande obtain necessary information by sample analysis, and then simulate the formation of Ryugu based on the evidencef obtained rom sample analysis. Eighteen stones (8 from Room A and 10 from Room C) were received from the ISAS curation facility on June 1, 2021, and brought into a fully nitrogen-displaced glove box at Tohoku University. At the same time, we also received the powder samples from Room A and Room C. To completely block the atmosphere from leaking into the container, all samples were put in the sample transport containers prepared by ISAS, transferred from the main chamber to the glovebox at ISAS, and then all containers were completely sealed in plastic bags with moisture and oxygen absorbers. No moisture or oxygen was detected when the bags were opened in the glove box at Tohoku University, so it was confirmed that there was no exposure to the atmosphere during transport. To date, a number of analyses have been carried out successfully and almost on schedule. The analysis started with the measurement of reflectance spectra, which are sensitive to atmospheric oxidation, hydroxylation, and adsorbed water. The visible, near-infrared, and mid-infrared reflectance spectra were measured while the samples were kept airtight. The spectra of powder samples and stone samples (as aggregates and as single stone) were successfully obtained. A major feature of the stone team's analysis is the use of synchrotron radiation facilities around the world. Since this analysis is non-destructive, stone samples whose reflectance spectra were measured were sent to KEK, SPring-8, ESRF (France), SOLEIL (France), DESY (Germany), and APS (USA). Using these synchrotron radiation facilities, high spatial resolution and sensitivity XRD, STXM, XANES, CT [1], IR-CT, FT-IR [2, 3], XRF, and Mössbauer analyses were performed. Most of the analyses were carried out under air-tight conditions on the stone samples and the particulates separated from the stone samples. These analyses allowed us to determine the three-dimensional distribution of minerals and elements, redox state, density and porosity of the stone samples. Furthermore, as a characteristic analysis of the stone team, light elemental analysis using negative Muon was performed at the MLF facility of J-PARC with an exceptionally long allocation of machine time. This is the only non-destructive method to measure the concentration of light elements in the whole (not the surface) of stone samples. Because the characteristic X-rays produced by muon irradiation are much higher in energy than the fluorescent X-rays produced by X-ray irradiation, there is little effect of self-absorption by the sample, and therefore, the concentration of light elements such as carbon, oxygen, and Na in the entire "stone" sample can be determined. Some stone samples are currently being measured for heat and strength physical properties in order to understand the physical properties of asteroid Ryugu. The data obtained from these measurements are useful for interpreting the remote-sensing data data taken from the surface layer of the asteroid Ryugu [4-7]. It is also important for understanding the behavior of the Ryugu material during impact events. The surfaces of many stone samples were observed by electron microscopy and other techniques, especially on natural “flat” surfaces formed on 5 stomes. As a result, characteristric mineral aggregates formed by the reactions with water and characteiristic impact features were observed on some of the samples. Based on the observations of surfaces and the synchrotron measurements of the whole stones, important objects such as characteristic structures and specific crystal aggregates for understanding the formation history of the asteroid were identified, and these parts were separated from the stone samples using an Xe beam (pFIB) and analyzed by various methods including transmission electron microscopy and synchrotron radiation analysis. Many stone samples, from which important objects have been separated, are embedded in epoxy resin and cut to produce many polished sections. Electron microscopy and spectroscopic measurements of the polished surfaces are being carried out to reveal the detailed mineralogical properties and elemental distribution inside the stone samples. In the fall, machine time for synchrotron radiation will begin, and we plan to analyze single crystals and characteristic objects separated from the stone samples.

Tomoki Nakamura↗

A Summary of the 2023 Joint High-Speed Boundary Layer Transition Workshop

A joint workshop between the Air Force Office of Scientific Research, the Office of Naval Research, and the NASA Hypersonic Technology Project was held in June 2023 on the topic of high-speed boundary-layer transition. The purpose of this workshop was to gather subject matter experts in the areas of supersonic and hypersonic boundary-layer transition in the areas of geometries of interest, computational methods, facilities and diagnostics, flight experiments, flow control, and new approaches and to discuss the current state of the art in the field. As gaps and accomplishments were identified, roadmaps were also created to guide future investments in these areas. The top recommendations are (1) to define relevant common geometries of interest that can be worked by multiple research groups; (2) improve modeling of high-enthalpy flows involving chemistry and ablation, studies of receptivity of freestream disturbances and atmospheric particulates into the boundary layer, surface feature characterization and modeling of changes to geometry; (3) design and determine viable flow control methods; and (4) move towards incorporating boundary layer transition prediction into a standard practice for design of high-speed vehicles. To execute this last recommendation successfully, investments beyond fundamental (basic and early applied) research are needed.

boundary layer transition↗

Advances and directions of ion nitriding/carburizing

Ion nitriding and carburizing are plasma activated thermodynamic processes for the production of case hardened surface layers not only for ferrous materials, but also for an increasing number of nonferrous metals. When the treatment variables are properly controlled, the use of nitrogenous or carbonaceous glow discharge medium offers great flexibility in tailoring surface/near-surface properties independently of the bulk properties. The ion nitriding process has reached a high level of maturity and has gained wide industrial acceptance, while the more recently introduced ion carburizing process is rapidly gaining industrial acceptance. The current status of plasma mass transfer mechanisms into the surface regarding the formation of compound and diffusion layers in ion nitriding and carbon build-up ion carburizing is reviewed. In addition, the recent developments in design and construction of advanced equipment for obtaining optimized and controlled case/core properties is summarized. Also, new developments and trends such as duplex plasma treatments and alternatives to dc diode nitriding are highlighted.

Spalvins, Talivaldis↗

New scaling law for turbulent boundary layers with high surface mass transfer

A fundamental understanding of the phenomena occurring in the turbulent boundary layer in the presence of surface blowing is limited, and considerable disagreements persist even in describing primary quantities, such as the boundary layer profile. The theories based on the linear boundary layer equations show that the thickness of the sublayer increases in the presence of surface blowing; therefore, the viscous sublayer and law of the wall modify. In this study, direct numerical simulations (DNS) of turbulent boundary layers with uniform surface mass transfers are carried out in order to scale the velocity profile. Emphasis is placed on moderate to high mass transfer rates, which are relevant to the most common hybrid rockets configuration. DNS data are used to establish a functional law of the wall and a law of wake by means of the relation between the wall shear stress and surface mass transfer. Analysis of the mean kinetic energy budget shows that the magnitude of turbulent kinetic energy increases by surface mass transfer, and the production rate extends significantly in the inner layer as the injection rate increases. DNS data of various surface blowing are used to complete the closure of turbulence kinetic energy equation and develop an eddy viscosity model. The predicted turbulent kinetic energy and eddy viscosity agree with DNS data for moderate to high blowing rates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The Interaction of Relativistic Spacecrafts with the Interstellar Medium

The Breakthrough Starshot initiative aims to launch a gram-scale spacecraft to a speed of v ∼ 0.2c, capable of reaching the nearest star system, α Centauri, in about 20 years. However, a critical challenge for the initiative is the damage to the spacecraft by interstellar gas and dust during the journey. In this paper, we quantify the interaction of a relativistic spacecraft with gas and dust in the interstellar medium (ISM). For gas bombardment, we find that damage by track formation due to heavy elements is an important effect. We find that gas bombardment can potentially damage the surface of the spacecraft to a depth of ∼0.1 mm for quartz material after traversing a gas column of N{sub H}∼2×10{sup 18} cm{sup −2} along the path to α Centauri, whereas the effect is much weaker for graphite material. The effect of dust bombardment erodes the spacecraft surface and produces numerous craters due to explosive evaporation of surface atoms. For a spacecraft speed v=0.2c, we find that dust bombardment can erode a surface layer of ∼0.5 mm thickness after the spacecraft has swept a column density of N{sub H}∼3×10{sup 17} cm{sup −2}, assuming the standard gas-to-dust ratio of the ISM. Dust bombardment also damages the spacecraft surface by modifying the material structure through melting. We calculate the equilibrium surface temperature due to collisional heating by gas atoms as well as the temperature profile as a function of depth into the spacecraft. Our quantitative results suggest methods for damage control, and we highlight possibilities for shielding strategies and protection of the spacecraft.

79 ASTRONOMY AND ASTROPHYSICS↗

The electronic structure of co-sputtered zinc indium tin oxide thin films

Zinc indium tin oxide (ZITO) transparent conductive oxide layers were deposited via radio frequency (RF) magnetron co-sputtering at room temperature. A series of samples with gradually varying zinc content was investigated. The samples were characterized with x-ray and ultraviolet photoemission spectroscopy (XPS, UPS) to determine the electronic structure of the surface. Valence and conduction bands maxima (VBM, CBM), and work function were determined. The experiments indicate that increasing Zn content results in films with a higher defect rate at the surface leading to the formation of a degenerately doped surface layer if the Zn content surpasses {approx}50%. Furthermore, the experiments demonstrate that ZITO is susceptible to ultraviolet light induced work function reduction, similar to what was earlier observed on ITO and TiO{sub 2} films.

36 MATERIALS SCIENCE↗

Generalized optical theorem for surface waves and layered media

We present a generalized optical theorem for surface waves. The theorem also applies to body waves since under many circumstances body waves can be written in terms of surface-wave modal summations. This theorem therefore extends the domain of applicability of the optical theorem from homogeneous background media to a general class of body and surface-wave propagation regimes within layered elastic media.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Wear characteristics of severely deformed aluminum sheets by accumulative roll bonding (ARB) process

Wear behavior of severely deformed aluminum sheets by accumulative roll bonding (ARB) process was characterized using a pin on disc wear machine at different conditions. The sheets were processed up to eight ARB cycles in order to induce a high strain ({approx} 6.4) to the samples. EBSD results showed that after eight cycles of ARB, sheets were found to contain ultrafine grains with high fraction of high angle grain boundaries. Wear experiments were conducted under different loading and operating conditions, including dry and immersion lubrication, and rotation speeds. Wear was continuously monitored by measuring the wear rates and morphologies of worn surfaces by scanning electron microscope (SEM). Contrary to expectation, the wear resistance of the ARBed Al sheets was less than the non-processed sheets. Wear rates of the ARBed Al sheets increased by increasing wear load and rotation speed, while, immersion lubrication decreased the wear rate significantly. Based on the observation and results, a model for the wear of the ARBed Al was proposed. - Research Highlights: {yields}The wear rate of the ARBed Al was higher than that of the non-processed alloy. {yields}This unexpected behavior was related to the low strain hardening capability and evolution of the ARB subsurface microstructure during the wear process. {yields}Sliding wear of the ARBed Al proceeded by surface deformation, and progressed by delamination of the deformed surface layer. {yields}The wear rate of ARBed Al increased by increasing applied load and sliding speed.

36 MATERIALS SCIENCE↗

Selective and Stable In-Promoted Fe Catalyst for Syngas Conversion to Light Olefins

A selective and stable alumina-supported In-promoted Fe catalyst (10 mol % In based on Fe) was discovered for converting syngas (2:1 H 2 /CO ratio) to olefins with high selectivity (45% with CO 2 included) and a remarkable stability (72 h run) at a CO conversion of 10% at 400 °C and 5 bar. The X-ray photoelectron spectroscopy results indicated that incorporating In into Fe catalysts changed the chemical bonding state of Fe and Fe/In composition near the surface layers, which affected the catalytic reactivity. Steady-state isotopic transient kinetic analysis showed that more stable CHx fragments are present on the catalyst surface when incorporating In into Fe, which can promote C–C coupling reaction toward olefins. Our study demonstrates that introducing In into Fe catalysts on Al 2 O 3 support can lower CO activation abilities. It has more impacts on lowering hydrogenation activity, which permits more C–C couplings and like of “ene” hydrogenation. Furthermore, weakening CO adsorption both in terms of sites and strength encouraged CO toward hydrocarbons rather than CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Distribution of Ti3+ Surface Sites in Reduced TiO2

We describe a DFT+U study of the (110) rutile surface with oxygen vacancies (Ov). Oxygen vacancies leave behind two excess unpaired electrons per Ov the formation of two Ti3+ ions. We investigate the location of the Ti3+ ions within the first three surface layers. In total we obtained 49 unique solutions of possible Ti3+ pairs, to examine the stability of all Ti types (e.g. five-coordinated surface Ti, six-coordinated surface Ti, sub-surface sites, etc.). Our results show that sub-surface sites are preferred, but that many configurations are close in energy, up to 0.3-0.4 eV of each other. In contrast to findings in previous work, we show that sites directly adjacent to the Ov are unstable. Analysis of our results show that the two Ti3+ ions within a pair behave independent of each other, as there are little electronic interactions between the excess electrons associated with these sites. We also examined the migration of Ti3+ sites from the surface into the bulk and find the surface locations to be preferred by ~ 0.5 eV relative to the bulk. Our systematic results provide a comprehensive picture of excess electrons that indicates that they are not trapped or localized at specific sites, but are distributed across several sites due to nearly degenerate Ti3+ states. This work was supported by the US Department of Energy Basic Energy Sciences' Chemical Sciences, Geosciences & Biosciences Division. Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemo-mechanical coupling in kerogen gas adsorption/desorption

We report that kerogen plays a central role in hydrocarbon generation in an oil/gas reservoir. In a subsurface environment, kerogen is constantly subjected to stress confinement or relaxation. The interplay between mechanical deformation and gas adsorption of the materials could be an important process for shale gas production but unfortunately is poorly understood. Using a hybrid Monte Carlo/molecular dynamics simulation, we show here that a strong chemo-mechanical coupling may exist between gas adsorption and mechanical strain of a kerogen matrix. The results indicate that the kerogen volume can expand by up to 5.4% and 11% upon CH 4 and CO 2 adsorption at 192 atm, respectively. The kerogen volume increases with gas pressure and eventually approaches a plateau as the kerogen becomes saturated. The volume expansion appears to quadratically increase with the amount of gas adsorbed, indicating a critical role of the surface layer of gas adsorbed in the bulk strain of the material. Furthermore, gas uptake is greatly enhanced by kerogen swelling. Swelling also increases the surface area, porosity, and pore size of kerogen. Here, our results illustrate the dynamic nature of kerogen, thus questioning the validity of the current assumption of a rigid kerogen molecular structure in the estimation of gas-in-place for a shale gas reservoir or gas storage capacity for subsurface carbon sequestration. The coupling between gas adsorption and kerogen matrix deformation should be taken into consideration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A nitrogen-hyperdoped silicon material formed by femtosecond laser irradiation

A supersaturation of nitrogen atoms is found in the surface layer of microstructured silicon after femtosecond (fs) laser irradiation in NF{sub 3}. The average nitrogen concentration in the uppermost 50 nm is about 0.5 ± 0.2 at. %, several orders of magnitude higher than the solid solubility of nitrogen atoms in silicon. The nitrogen-hyperdoped silicon shows high crystallinity in the doped layer, which is due to the repairing effect of nitrogen on defects in silicon lattices. Nitrogen atoms and vacancies can be combined into thermal stable complexes after fs laser irradiation, which makes the nitrogen-hyperdoped silicon exhibit good thermal stability of optical properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Surface brightness temperatures at the Apollo 17 heat flow site - Thermal conductivity of the upper 15 cm of regolith

Lunar surface brightness temperatures derived as part of the Apollo 17 heat flow experiment are reported. Nighttime surface temperatures, calculated from the data provided by two thermocouples suspended about 15 cm above the lunar surface, are used to determine the conductivity profile of the upper 15 cm of regolith at the ALSEP site. The surface reaches a maximum temperature of 384 (plus or minus 6) K at lunar noon and cools to a minimum temperature of 102 (plus or minus 1.5 K) at the end of the lunar night. Conductivities of the order of .000015 W/cm-deg K are postulated for a 2-cm porous surface layer overlying more compact regolith material with conductivities in the range of .0001 to .00015 W/cm-deg K between 2 and 15 cm. A mean surface temperature of 216 (plus or minus 5) K is deduced from the thermocouple data. The 256 K temperature measured by the probe sensors at 130 cm thus indicates that a large mean temperature gradient exists at the Apollo 17 site.

Keihm, S. J.↗

The aeolian wind tunnel

The aeolian wind tunnel is a special case of a larger subset of the wind tunnel family which is designed to simulate the atmospheric surface layer winds to small scale (a member of this larger subset is usually called an atmospheric boundary layer wind tunnel or environmental wind tunnel). The atmospheric boundary layer wind tunnel is designed to simulate, as closely as possible, the mean velocity and turbulence that occur naturally in the atmospheric boundary layer (defined as the lowest portion of the atmosphere, of the order of 500 m, in which the winds are most greatly affected by surface roughness and topography). The aeolian wind tunnel is used for two purposes: to simulate the physics of the saltation process and to model at small scale the erosional and depositional processes associated with topographic surface features. For purposes of studying aeolian effects on the surface of Mars and Venus as well as on Earth, the aeolian wind tunnel continues to prove to be a useful tool for estimating wind speeds necessary to move small particles on the three planets as well as to determine the effects of topography on the evolution of aeolian features such as wind streaks and dune patterns.

Iversen, J. D.↗