Search NASA⌕ Search

SEARCH · Search NASA

Results for “BLADE TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Structure-borne noise estimates for the PTA aircraft

Estimates of the level of in-flight structure-borne noise transmission in the Propfan Test Assessment Aircraft were carried out for the first three blade passage frequencies. The procedure used combined the frequency response functions of wing strain to cabin sound pressure level (SPL) response obtained during ground test with in-flight measured wing strain response data. The estimated cabin average in-flight structure-borne noise levels varied from 64 to 84 dB, with an average level of 74 dB. The estimates showed little dependence on engine/propeller power, flight altitude, or flight Mach number. In general, the bare cabin noise levels decreased with increasing propeller tone, giving rise to a plausible structure-borne noise transmission problem at the higher blade passage tones. Without knowledge of the effects of a high insertion loss side wall treatment on structure-borne noise transmission, no quantitative conclusions could be made.

Unruh, James F.↗
NASA NTRS1989

A compendium of controlled diffusion blades generated by an automated inverse design procedure

A set of sample cases was produced to test an automated design procedure developed at the NASA Lewis Research Center for the design of controlled diffusion blades. The range of application of the automated design procedure is documented. The results presented include characteristic compressor and turbine blade sections produced with the automated design code as well as various other airfoils produced with the base design method prior to the incorporation of the automated procedure.

Sanz, Jose M.↗
NASA NTRS1980

Advanced ceramic material for high temperature turbine tip seals

Forty-one material systems were evaluated for potential use in turbine blade tip seal applications at 1370 C. Both ceramic blade tip inserts and abradable ceramic tip shoes were tested. Hot gas erosion, impact resistance, thermal stability, and dynamic rub performance were the criteria used in rating the various materials. Silicon carbide and silicon nitride were used, both as blade tips and abradables. The blade tip inserts were fabricated by hot pressing while low density and honeycomb abradables were sintered or reaction bonded.

Vogan, J. W.↗
NASA NTRSDate not supplied

Cavitation Effects on the Structural Dynamics of Turbomachinery Components

The structural integrity of inducer and impeller blades in rocket engine turbomachinery must be evaluated in the face of complex excitation mechanisms including fluctuating pressures due to cavitation. Cavitation occurs when the local fluid pressure drops below the vapor pressure, causing the formation of vapor-filled bubbles. Cavitation can exist to various extents within the typical operating range of rocket engine turbopumps. Despite recent progress towards reducing uncertainties in structural dynamic models of turbomachinery components, the extent to which pump cavitation affects the structural dynamic properties (i.e., natural frequencies, damping, and mode shapes) of inducer and impeller blades remains largely unknown. To study the structural dynamic effects of cavitating flows, experiments are conducted in a high-speed water tunnel. The test article is a low aspect ratio cantilevered plate, thus mimicing a single inducer blade that is unwrapped from its hub. The test article is oriented at zero angle of attack and has a triangular trip at its leading edge to induce cavitation. To change the extent of cavitation, the static pressure of the water tunnel is controlled. A high-speed camera is used to quantify the coverage of the cavitation sheet.

Fluid-Structure Interaction↗
NASA NTRSDate not supplied

Cavitation Effects on the Structural Dynamics of Turbomachinery Components

The structural integrity of inducer and impeller blades in rocket engine turbo machinery must be evaluated in the face of complex excitation mechanisms including fluctuating pressures due to cavitation. Cavitation occurs when the local fluid pressure drops below the vapor pressure, causing the formation of vapor-filled bubbles. Cavitation can exist to various extents within the typical operating range of rocket engine turbo pumps. Despite recent progress towards reducing uncertainties in structural dynamic models of turbo machinery components, the extent to which pump cavitation affects the structural dynamic properties (i.e., natural frequencies, damping, and mode shapes) of inducer and impeller blades remains largely unknown. To study the structural dynamic effects of cavitating flows, experiments are conducted in a high-speed water tunnel. The test article is a low aspect ratio cantilevered plate, thus mimicing a single inducer blade that is unwrapped from its hub. The test article is oriented at zero angle of attack and has a triangular trip at its leading edge to induce cavitation. To change the extent of cavitation, the static pressure of the water tunnel is controlled. A high-speed camera is used to quantify the coverage of the cavitation sheet.

Structural Dynamics↗
DOE OSTI2011

An Innovative Technique for Evaluating the Integrity and Durability of Wind Turbine Blade Composites - Final Project Report

To build increasingly larger, lightweight, and robust wind turbine blades for improved power output and cost efficiency, durability of the blade, largely resulting from its structural composites selection and aerodynamic shape design, is of paramount concern. The safe/reliable operation of structural components depends critically on the selection of materials that are resistant to damage and failure in the expected service environment. An effective surveillance program is also necessary to monitor the degradation of the materials in the course of service. Composite materials having high specific strength/stiffness are desirable for the construction of wind turbines. However, most high-strength materials tend to exhibit low fracture toughness. That is why the fracture toughness of the composite materials under consideration for the manufacture of the next generation of wind turbines deserves special attention. In order to achieve the above we have proposed to develop an innovative technology, based on spiral notch torsion test (SNTT) methodology, to effectively investigate the material performance of turbine blade composites. SNTT approach was successfully demonstrated and extended to both epoxy and glass fiber composite materials for wind turbine blades during the performance period. In addition to typical Mode I failure mechanism, the mixed-mode failure mechanism induced by the wind turbine service environments and/or the material mismatch of the composite materials was also effectively investigated using SNTT approach. The SNTT results indicate that the proposed protocol not only provides significant advance in understanding the composite failure mechanism, but also can be readily utilized to assist the development of new turbine blade composites.

17 WIND ENERGY↗
NASA NTRS2001

Vortex Wake Geometry of a Model Tilt Rotor in Forward Flight

A full-span 0.25-scale V-22 tiltrotor was tested in the NASA Ames 40-by 80-Foot Wind Tunnel in November 2000. The main objective of the test was to acquire a comprehensive database to validate tiltrotor analyses. Figure 1 shows the model installed in the Ames 40- by 80-Foot Wind Tunnel. Rotor and vehicle performance measurements were taken in addition to wing pressures, acoustics, and flow visualization. A dual acoustic traverse system was installed to measure blade-vortex interaction (BVI) noise levels and directivity. Test conditions included hover and forward flight in helicopter mode. Angle-of-attack and thrust sweeps for three tunnel speeds were acquired before model problems caused the premature conclusion of the test. The test will resume in the Ames 80- by 120-Foot Wind Tunnel in late 2001. This paper will focus on the wake geometry measurements that were acquired during the test. The wake geometry measurements were a small subset of a larger matrix of planned measurements designed to study the development and structure of the dual vortex system generated during BVI conditions. The present paper will provide wake geometry data for four test conditions. In addition, the data will be compared with previously acquired wake measurements from an isolated tiltrotor

Wadcock, Alan J.↗
NASA NTRS2018

Aerodynamics and Aeroacoustic Sources of a Coaxial Rotor

Vehicles with coaxial, contra-rotating rotor systems (CACR) are being considered for a range of applications. Design parameters are identified that effect the fundamental aerodynamics and fluid dynamic features of a CACR in hover, vertical, and edgewise flight. Understanding the fluid dynamic features is a precursor to studying the aeroacoustics of a coaxial rotor. Rotor performance was computed initially using Navier-Stokes solver with prescribed blade section aerodynamic properties, the results validated against generic experimental test cases. Using a A 2D potential flow code and 2D OVERFLOW compressible-flow Navier-Stokes solver, the fluid dynamics of blade interactions was simplified and broken into a 2D blade crossing problem, with crossing locations and velocity fields from the rotor results to understand circulation, thickness, compressibility, shed vorticity, downwash, and viscosity effects. A calculation tool has been developed to identify time and location of blade overlap and BVI time location for CACR. Specific aerodynamic phenomena that occur for each noise source relevant to CACR are presented, along with computational tools to predict these occurrences.

Aeroacoustic↗
NASA NTRS1973

Noise and wake structure measurements in a subsonic tip speed fan

The results of an experimental program are reported which show the effect of blade angle, tip speed, fan pressure ratio, and thrust on noise of a model fan of 0.457m (18 inches) diameter operating at subsonic tip speeds at pressure ratios between 1.06 and 1.15. The fan used in this study had 12 blades, 7 stator vanes, and a spacing between the rotor and stator of 1.85 blade chords. This fan was originally designed for aerodynamic testing and was considered a good performer. It was used in the noise test program as it incorporated features found to reduce noise in an earlier analytical parametric study. For a given pressure ratio the fan was shown to exhibit minimum noise at the blade angle and tip speed near that of maximum aerodynamic efficiency. Also, the noise level and spectrum character of this fan showed excellent correlation with scaled data of a similar larger diameter fan. Results of the program confirm the trends shown in the earlier analytical parametric study which showed that fan noise could be reduced for a given thrust and pressure ratio by increasing fan solidity, improving fan aerodynamic design, and operating the fan at an optimum subsonic tip speed. In addition to noise, the blade wake characteristics at the leading edge of the stator were measured in this program. At root and tip sections some difference between predicted and measured wakes was found. However comparisons between predicted and measured wakes at mid span locations was found to be good.

Magliozzi, B.↗
NASA NTRS2004

New Dynamic Spin Rig Capabilities Used to Determine Rotating Blade Dynamics

The Dynamic Spin Rig Facility at the NASA Glenn Research Center is used to determine the structural response of rotating engine components without the effects of aerodynamic loading. Recently, this rig's capabilities were enhanced through the replacement of grease-lubricated ball bearings with magnetic bearings. Magnetic bearings offer a number of advantages--the most important here being that they not only fully support the rotor system, but excite it as well. Three magnetic bearings support the rotor and provide five axes of controlled motion: an x- and y-axis translation at each of two radial bearings and a z-axis translation in the vertical or axial direction. Sinusoidal excitation (most commonly used) can be imparted on the rotor through the radial magnetic bearings in either a fixed or rotating frame of reference. This excitation is added directly to the magnetic bearing control output. Since the rotor is fully levitated, large translations and rotations of the rotor system can be achieved. Some of the capabilities of this excitation system were determined and reported. The accelerations obtained at the tip of a titanium flat plate test article versus the swept sine excitation sent to both radial bearings in phase and perpendicular to the plane containing the two blades are shown. Recent tests required the excitation of fundamental bending and torsional blade resonances at rotor speeds up to 10,000 rpm. Successful fixed synchronous rotation of the excitation signal provided the best detectable blade resonant vibrations at excitation frequencies up to 1100 Hz for the particular blades of interest. A noncontacting laser measurement system was used to collect blade-tip motions. From these data, the amplitude and frequency of the motion could be determined as well as the blade damping properties. Damping could be determined using two methods: (1) free decay and (2) curve fitting the vibration amplitude as a function of frequency in and around the resonance of interest and using the half-power method. The free decay of a composite blade vibrating at its first bending resonance while rotating at 3000 rp is shown. This new system is currently being used to support the Efficient Low-Noise Fan project at Glenn. The damping properties of prototype hollow composite blades specially designed to reduce fan noise are currently being determined.

Provenza, Andrew J.↗
NASA NTRS1977

Sensor for measuring instantaneous angle of attack of helicopter blades

Various research activities are reported in the following areas: (1) improving and testing probes; (2) theoretical studies of probe motion; and (3) improving research facilities. It is concluded that a satisfactory solution to the problem of measuring angle of attack of helicopter blades may be found in the near future.

Barna, P. S.↗
DOE OSTI2019

Development and data path integration test of the global Feature EXtractor for the ATLAS Level-1 calorimeter trigger system Phase-I upgrade

The global Feature Extractor (gFEX) is a component of the Phase-I upgrade of the Level-1 Calorimeter (L1Calo) trigger system for the ATLAS experiment at the Large Hadron Collider (LHC) at CERN. The gFEX is used to identify patterns of energy associated with the hadronic decays of high momentum Higgs, W and Z bosons, top quarks, and exotic particles in real time at the 40 MHz LHC bunch crossing rate. Three prototypes were implemented and tested from 2014 to 2017. With the lessons learned from the prototypes, the final gFEX production board has been implemented at the end of 2017. The gFEX receives up to 300 fiber optical links from the calorimeter and transmits trigger data on 96 links to the ATLAS Level-1 Topological [1] (L1Topo) trigger at a rate of up to 12.8 Gb/s. There are also 24 electrical links on board for communication between two FPGAs running at speeds of up to 25.6 Gb/s. Here, the hardware functionality and performance of the production board have been evaluated. A data path integration test between the Liquid Argon Digital Processing Blade (LDPB) [2] and the Front End LInk eXchange (FELIX) [3] was performed successfully at CERN in 2018.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Near wake evolution of a tidal stream turbine due to asymmetric sheared turbulent inflow with different integral length scales

Tidal stream turbines deployed at highly energetic open water sites are subjected to sheared inflow in the rotor plane. The inflow shear is expected to cause asymmetric loading on the rotor blades and affect the downstream wake. In the current study, two different turbulent inflow conditions, static-high shear and dynamic shear, were generated via an active-grid turbulence generator. A 1:20 scaled three-bladed horizontal axis tidal turbine model was tested in those conditions. The results were compared to a quasi-laminar case with no imposed turbulence or shear. The results show that the high shear reduces the average performance, with a drop of up to 16% in the optimal power coefficient. Besides, the shear profiles increase torque fluctuations and induce significant differences in wake hydrodynamics between the high-speed (upper) and low-speed (lower) regions. The large integral length scales further enhance the load fluctuations perceived by the rotor but have a negligible effect on the mean wake field quantities and the wake recovery. The lower half region featured a faster breakdown of tip vortex structure and a rapid drop of swirl number, a phenomenon conjectured to be a consequence of the strong turbulence intensities and Reynolds stresses in the lower half region. Furthermore, the sheared turbulent inflow also results in a very intensive energy redistribution process towards large-scale, low-frequency motions, which is important to the downstream turbines.

16 TIDAL AND WAVE POWER↗
NASA NTRS1973

Analytical and experimental investigation of aircraft metal structures reinforced with filamentary composites. Phase 3: Major component development

Analytical and experimental investigations, performed to establish the feasibility of reinforcing metal aircraft structures with advanced filamentary composites, are reported. Aluminum-boron-epoxy and titanium-boron-epoxy were used in the design and manufacture of three major structural components. The components were representative of subsonic aircraft fuselage and window belt panels and supersonic aircraft compression panels. Both unidirectional and multidirectional reinforcement concepts were employed. Blade penetration, axial compression, and inplane shear tests were conducted. Composite reinforced structural components designed to realistic airframe structural criteria demonstrated the potential for significant weight savings while maintaining strength, stability, and damage containment properties of all metal components designed to meet the same criteria.

Bryson, L. L.↗
NASA NTRS1974

Research turbine for high temperature core engine application. 1: Cold-airoverall performance of solid scaled turbine

A solid, half-scale model of a 50.8-cm (20-in) research turbine designed for a high temperature core engine application was investigated over a range of speeds and pressure ratios. The results of this test are presented. The effect of rotor blade twist was also investigated. At the design equivalent speed and specific work output, the total efficiency of the turbine with untwisted rotor blades was 87.1 percent; at the same pressure ratio the efficiency of the turbine with twisted rotor blades was 88.0 percent.

Szanca, E. M.↗
NASA NTRS1973

Experience with Jacobs wind-driven electric generating plant, 1931 - 1957

Engineering, construction, performance, electric output, and different uses of the wind electric 2500- to 3000-watt plant are outlined. After several years of testing different types of windmills, the three blade aeroplane type of propeller was found to be far superior in power output. By means of a flyball governor operated, variable pitch speed control, the maximum speed of the propeller was accurately and easily controlled, to prevent excessive speeds in high winds and storms. The three blade propeller was found to be necessary to prevent excessive vibration whenever the shift of the wind direction required the plant to change its facing direction on the tower.

Jacobs, M. L.↗
NASA NTRS1974

Hightip-speed, low-loading transonic fan stage. Part 2: Data compilation

Tests were conducted on a high-tip-speed low-loading transonic fan stage to determine the performance and inlet flow distortion tolerance of the design. Test data were recorded for overall and blade element performance with both uniform and distorted inlet flows. A tabular summary of the data and a representative selection of the computer data reduction sheets are presented.

Ware, T. C.↗
NASA NTRS1976

Progress report on propeller aircraft flyover noise research

Initial results of a program to investigate the sources of noise in unshrouded propellers under forward flight conditions are reported. Tests were conducted using a three-blade full-scale instrumented propeller mounted on a twin-engine aircraft. Measurements included (1) far-field noise at fixed ground stations and at two aircraft wing tip locations, (2) blade surface pressures at seven locations on one of the propeller blades, (3) atmospheric turbulence encountered by the aircraft in flight, and (4) aircraft operating conditions. The results confirm that significantly lower levels of propeller noise are produced in forward flight than at static conditions. It is tentatively concluded that propeller noise generation in flight may be dominated by steady loading at blade passage frequency, but at higher frequencies unsteady loading due to interaction with natural atmospheric turbulence may be the dominant mechanism of noise generation. Under static conditions the total noise signature appears to be the result of interaction of the propeller with persistent turbulent eddies passing through the propeller disk.

Metzger, F. B.↗