Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computer simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

A jet controlled magnetic referenced attitude control system for spinning payloads

An attitude control system was designed permitting large angle acquisition and alignment of the principle axis of a spinning payload to within 1 degree of the earth's magnetic field. Signals from magnetometer and gyro sensors are fed to the control algorithm to generate commands for the jet thrusters. The algorithm contains a cross axis magnetometer signal to prevent a large angle magnetometer signal to prevent a large angle equilibrium solution. The acquisition will occur within 50 seconds from initial precession and nutation angles of 30 degrees. An electronic spin filter passes signals at spin and nutation frequencies and rejects bias signals due to sensor misalignment and principle axis offset. Describing function analysis and total analog simulation techniques were used. The flight ACS hardware was interfaced with the analog computer simulation for design and verification. The controller has flown on four successful missions.

Celmer, J. J.↗
NASA NTRS1993

Motion control of 7-DOF arms - The configuration control approach

Graphics simulation and real-time implementation of configuration control schemes for a redundant 7-DOF Robotics Research arm are described. The arm kinematics and motion control schemes are described briefly. This is followed by a description of a graphics simulation environment for 7-DOF arm control on the Silicon Graphics IRIS Workstation. Computer simulation results are presented to demonstrate elbow control, collision avoidance, and optimal joint movement as redundancy resolution goals. The laboratory setup for experimental validation of motion control of the 7-DOF Robotics Research arm is then described. The configuration control approach is implemented on a Motorola-68020/VME-bus-based real-time controller, with elbow positioning for redundancy resolution. Experimental results demonstrate the efficacy of configuration control for real-time control.

Seraji, Homayoun↗
NASA NTRS1997

An Ecosystem Simulation Model for Methane Production and Emission from Wetlands

Previous experimental studies suggest that methane emission from wetland is influenced by multiple interactive pathways of gas production and transport through soil and sediment layers to the atmosphere. The objective of this study is to evaluate a new simulation model of methane production and emission in wetland soils that was developed initially to help identify key processes that regulate methanogenesis and net flux of CH4 to the air, but which is designed ultimately for regional simulation using remotely sensed inputs for land cover characteristics. The foundation for these computer simulations is based on a well-documented model (CASA) of ecosystem production and carbon cycling in the terrestrial blaspheme. Modifications to represent flooded wetland soils and anaerobic decomposition include three new sub-models for: (1) layered soil temperature and water table depth (WTD) as a function of daily climate drivers, (2) CH4 production within the anoxic soil layer as a function of WTD and CO2 production under poorly drained conditions, and (3) CH4 gaseous transport pathways (molecular diffusion, ebullition, and plant vascular transport) as a function of WTD and ecosystem type. The model was applied and tested using climate and ecological data to characterize tundra wetland sites near Fairbanks, Alaska studied previously by Whalen and Reeburgh. Comparison of model predictions to measurements of soil temperature and thaw depth, water-table depth, and CH4 emissions over a two year period suggest that inter-site differences in soil physical conditions and methane fluxes could be reproduced accurately for selected periods. Day-to-day comparison of predicted emissions to measured CH4 flux rates reveals good agreement during the early part of the thaw season, but the model tends to underestimate production of CH4 during the months of July and August in both test years. Important seasonal effects, including that of falling WTD during these periods, are apparently overlooked in the model formulation. Nevertheless, reasonably close agreement was achieved between the model's mean daily and seasonal estimates of CH4 flux and observed emission rates for northern wetland ecosystems. Several features of the model are identified as crucial to more accurate prediction of wetland methane emission, including the capacity to incorporate influences of localized topographic and hydrologic features on site-specific soil temperature and WTD dynamics, and mechanistic simulation of methane emission transport pathways from within the soil profile.

Potter, C. S.↗
NASA NTRS2005

Space Shuttle Underside Astronaut Communications Performance Evaluation

The Space Shuttle Ultra High Frequency (UHF) communications system is planned to provide Radio Frequency (RF) coverage for astronauts working underside of the Space Shuttle Orbiter (SSO) for thermal tile inspection and repairing. This study is to assess the Space Shuttle UHF communication performance for astronauts in the shadow region without line-of-sight (LOS) to the Space Shuttle and Space Station UHF antennas. To insure the RF coverage performance at anticipated astronaut worksites, the link margin between the UHF antennas and Extravehicular Activity (EVA) Astronauts with significant vehicle structure blockage was analyzed. A series of near-field measurements were performed using the NASA/JSC Anechoic Chamber Antenna test facilities. Computational investigations were also performed using the electromagnetic modeling techniques. The computer simulation tool based on the Geometrical Theory of Diffraction (GTD) was used to compute the signal strengths. The signal strength was obtained by computing the reflected and diffracted fields along the propagation paths between the transmitting and receiving antennas. Based on the results obtained in this study, RF coverage for UHF communication links was determined for the anticipated astronaut worksite in the shadow region underneath the Space Shuttle.

Hwu, Shian U.↗
NASA NTRS2013

Calculating Conductance of Ion Channels

We have simulated two small ion channels in a water/membrane system, which consists of 71,000-72,000 atoms, and have estimated the conductance by way of counting ions crossing these channels in applied field. The calculated values of conductance have been compared with predictions of the electrodiffusion model. In a recently developed theoretical framework, all commonly used assumptions of the model can be tested. If they are satisfied, which is often the case, the approach provides a rigorous way to extrapolate conductance calculated at one voltage to other voltages. This, in turn, allows for efficient estimations of current-voltage dependence, examining rectifying behavior of channels and calculating the reversal potential. Furthermore, the consistency of the results can be precisely tested. Simulations at microsecond time scales are required to sufficiently reduce statistical errors and separate them from possible systematic errors. Only then the accuracy of the proposed approach can be properly tested. Linking simulations with electrophysiology provides a stringent, highly relevant test for the correctness of computer simulations of ion channels. Considering biological, medical and pharmaceutical importance of these proteins, results of the proposed study might motivate the development of improved hardware and software that would enable applying a similar strategy to more complex channels at longer times.

Ion↗
DOE OSTI2024

Buffer-IPyC separation process in TRISO fuel particles simulated with Bison code

During High Temperature Gas-cooled Reactor (HTGR) operation, tristructural isotropic (TRISO) coated-particle fuel undergoes irradiation-induced changes in morphology and thermomechanical properties. Experimental results from the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program show, among other things, the mechanism of gap formation between the buffer and inner pyrolytic carbon (IPyC) layers, which could be explored further via computational simulations using the Bison code. Two simulation models were developed, the debonding restricted model, where no gap formation between buffer and IPyC layers is permitted, and the debonding enabled model, where the gap between those layers is created. The inputs of the simulated models are based on the irradiation conditions from the AGR-1 experiment. The research included simulations on spherical and aspherical fuel types. Under the specific temperatures and fluences of the AGR-1 irradiation experiment, and the Bison simulations, it was concluded that the most common scenario is a gap formation along the buffer-IPyC interface, while the least possible scenario is the situation where there is no gap formation at the buffer-IPyC junction. The computational results confirmed that the sphericity of the fuel influences the thickness of the gap that occurs at the buffer-IPyC junction, in a way that with increasing aspect ratio the gap thickness increases. The results obtained for spherical and aspherical fuel are nearly identical. Finally, performed simulations match conclusions observed from the AGR-1 experiment, which as such shows that the Bison code is a good computational method for simulating the TRISO fuel. Future simulations will include the validation of performed research and comparison of the results between Bison and PARFUME codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Nonlinear simulation of under-resolved flows with shocks

Here, we consider the numerical simulation of advection-dominated flows whose wide range of physical length scales exceed the memory capacity of finite computers. Simulating flows with shocks and turbulence presented challenges for the earliest computers that were quickly overcome by the development of new numerical methodology. Principal among those new ideas were artificial viscosity and finite volume methods, concepts that remain in common use today. We begin by describing the history of those methods, the innovators and their motivations. We then describe the development of finite scale theory, a reformulation of Navier–Stokes theory that exposes the physical principles on which artificial viscosity is based. We discuss the essential properties of the finite scale equations, the observer, unresolved kinetic energy and inviscid energy dissipation. We briefly consider the implementation of the finite scale equations on the computer from the point of view of Gisin’s conjectures about finite information.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1972

Theory and simulation of the beam cyclotron instability.

A theory of plasma beam cyclotron instability is developed on the basis of computer simulation experiments. The theory holds that at certain turbulence levels, electron cross-field diffusion which supresses the electron gyroresonances is created by turbulent wave-particle interactions in a plasma beam after a period of quasi-linear exponential development of turbulence. The stabilizing effect of Landau ion damping is noted. The behavior of cold and hot ions is discussed.

Lampe, M.↗
NASA NTRS1972

Space Ultrareliable Modular Computer (SUMC) instruction simulator

The design principles, description, functional operation, and recommended expansion and enhancements are presented for the Space Ultrareliable Modular Computer interpretive simulator. Included as appendices are the user's manual, program module descriptions, target instruction descriptions, simulator source program listing, and a sample program printout. In discussing the design and operation of the simulator, the key problems involving host computer independence and target computer architectural scope are brought into focus.

Curran, R. T.↗
DOE OSTI2025

Market Driven Residential Energy Codes: Comparing Performance in a Changing Technological Environment

The research project is undertaken to better understand the changing relationship between the two basic methods of building energy code compliance – prescriptive and performance – and how those methods relate to each other with respect to advancements in building energy computer simulation standards and capabilities. The International Energy Efficiency Code (IECC) is a model code adopted by many jurisdictions across the United States. Historically, the prescriptive compliance methodology has been preferred in most jurisdictions. The prescriptive methodology requires meeting or exceeding specific efficiency minimums for each envelope component. This tends to be a simple method to teach and verify. A more involved prescriptive alternative called the Total UA alternative is sometimes used. This method requires some multiplication, summing, and comparison to compute, so it is done with a fairly simple computer program. However, advances in computer and building energy simulation technology have resulted in increased use of more detailed performance compliance methods. The performance compliance method establishes the annual energy cost threshold via hourly simulation models. The compliance threshold is determined with a comparison building model simulation with geometry similar to the proposed home and with energy feature parameters and efficiencies as specified in the IECC. This project examines relationships between the two methods of building energy code compliance, including: • Overall annual energy use based on utility bill analysis by compliance method • Code official work processes with respect to compliance methods • Gaps and issues associated with building code compliance methods • Simulated energy use difference between compliance methods • Code compliance cost as a function of compliance method • Code compliance labeling effectiveness for high performance residences • Getting to net zero energy use and net zero greenhouse gas emissions through high performance code alternatives • Electronic code permitting and compliance alternatives

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS1988

Appendices to the model description document for a computer program for the emulation/simulation of a space station environmental control and life support system

A Model Description Document for the Emulation Simulation Computer Model was already published. The model consisted of a detailed model (emulation) of a SAWD CO2 removal subsystem which operated with much less detailed (simulation) models of a cabin, crew, and condensing and sensible heat exchangers. The purpose was to explore the utility of such an emulation simulation combination in the design, development, and test of a piece of ARS hardware, SAWD. Extensions to this original effort are presented. The first extension is an update of the model to reflect changes in the SAWD control logic which resulted from test. Also, slight changes were also made to the SAWD model to permit restarting and to improve the iteration technique. The second extension is the development of simulation models for more pieces of air and water processing equipment. Models are presented for: EDC, Molecular Sieve, Bosch, Sabatier, a new condensing heat exchanger, SPE, SFWES, Catalytic Oxidizer, and multifiltration. The third extension is to create two system simulations using these models. The first system presented consists of one air and one water processing system. The second consists of a potential air revitalization system.

Yanosy, James L.↗
NASA NTRS1988

Appendices to the user's manual for a computer program for the emulation/simulation of a space station environmental control and life support system

A user's Manual for the Emulation Simulation Computer Model was published previously. The model consisted of a detailed model (emulation) of a SAWD CO2 removal subsystem which operated with much less detailed (simulation) models of a cabin, crew, and condensing and sensible heat exchangers. The purpose was to explore the utility of such an emulation/simulation combination in the design, development, and test of a piece of ARS hardware - SAWD. Extensions to this original effort are presented. The first extension is an update of the model to reflect changes in the SAWD control logic which resulted from the test. In addition, slight changes were also made to the SAWD model to permit restarting and to improve the iteration technique. The second extension is the development of simulation models for more pieces of air and water processing equipment. Models are presented for: EDC, Molecular Sieve, Bosch, Sabatier, a new condensing heat exchanger, SPE, SFWES, Catalytic Oxidizer, and multifiltration. The third extension is to create two system simulations using these models. The first system presented consists of one air and one water processing system, the second a potential Space Station air revitalization system.

Yanosy, James L.↗
NASA NTRS1996

Virtual Reality Simulation of the International Space Welding Experiment

Virtual Reality (VR) is a set of breakthrough technologies that allow a human being to enter and fully experience a 3-dimensional, computer simulated environment. A true virtual reality experience meets three criteria: (1) It involves 3-dimensional computer graphics; (2) It includes real-time feedback and response to user actions; and (3) It must provide a sense of immersion. Good examples of a virtual reality simulator are the flight simulators used by all branches of the military to train pilots for combat in high performance jet fighters. The fidelity of such simulators is extremely high -- but so is the price tag, typically millions of dollars. Virtual reality teaching and training methods are manifestly effective, and we have therefore implemented a VR trainer for the International Space Welding Experiment. My role in the development of the ISWE trainer consisted of the following: (1) created texture-mapped models of the ISWE's rotating sample drum, technology block, tool stowage assembly, sliding foot restraint, and control panel; (2) developed C code for control panel button selection and rotation of the sample drum; (3) In collaboration with Tim Clark (Antares Virtual Reality Systems), developed a serial interface box for the PC and the SGI Indigo so that external control devices, similar to ones actually used on the ISWE, could be used to control virtual objects in the ISWE simulation; (4) In collaboration with Peter Wang (SFFP) and Mark Blasingame (Boeing), established the interference characteristics of the VIM 1000 head-mounted-display and tested software filters to correct the problem; (5) In collaboration with Peter Wang and Mark Blasingame, established software and procedures for interfacing the VPL DataGlove and the Polhemus 6DOF position sensors to the SGI Indigo serial ports. The majority of the ISWE modeling effort was conducted on a PC-based VR Workstation, described below.

Phillips, James A.↗
NASA NTRS1993

Probabilistic assessment of composite structures

A general purpose methodology for integrated probabilistic assessment of composite structures is demonstrated using aircraft fuselage type structures with rectangular cutouts. The computational simulation took into account buckling loads, vibration frequencies, global displacements, and local stresses. The procedure was embedded into the computer code IPACS (Integrated Probabilistic Assessment of Composite Structures) that calculates the simulated scatter, the sensitivity of the composite structural behavior to all the primitive variables that affect the structural behavior. The probabilistic assessment for the composite structure with rectangular cutouts indicates that the uncertainty in the longitudinal ply stress is mainly due to uncertainty in the laminate thickness.

Shiao, Michael C.↗
NASA NTRS2019

SI IV Resonance Line Emission during Solar Flares: Non-LTE, Non-equilibrium, Radiation Transfer Simulations

The Interface Region Imaging Spectrograph routinely observes the Si IV resonance lines. When analyzing quiescent observations of these lines, it has typically been assumed that they form under optically thin conditions. This is likely valid for the quiescent Sun, but this assumption has also been applied to the more extreme flaring scenario. We used 36 electron-beam-driven radiation hydrodynamic solar flare simulations, computed using the RADYN code, to probe the validity of this assumption. Using these simulated atmospheres, we solved the radiation transfer equations to obtain the non-LTE, nonequilibrium populations, line profiles, and opacities for a model silicon atom, including charge exchange processes. This was achieved using the "minority species" version of RADYN. The inclusion of charge exchange resulted in a substantial fraction of Si IV at cooler temperatures than those predicted by ionization equilibrium. All simulations with an injected energy flux F> 5 x 10(exp 10) erg cm(exp -2) s(exp -1) resulted in optical depth effects on the Si IV emission, with differences in both intensity and line shape compared to the optically thin calculation. Weaker flares (down to F ~ 10(exp 9) erg cm(exp -2) s(exp -1)) also resulted in Si IV emission forming under optically thick conditions, depending on the other beam parameters. When opacity was significant, the atmospheres generally had column masses in excess of 5 x 10-6 g cm-2 over the temperature range 40-100 kK, and the Si IV formation temperatures were between 30 and 60 kK. We urge caution when analyzing Si IV flare observations, or when computing synthetic emission without performing a full radiation transfer calculation.

Kerr, Graham S.↗
NASA NTRS2007

Progressive Fracture of Laminated Composite Stiffened Plate

Laminated fiber-reinforced composite stiffened plate with [0/90/plus or minus 45]s plies made of S-Glass/epoxy are evaluated via computational simulation to study damage and fracture progression. The loads are pressure and temperature which varies from 21 to 65.5 C (case I) and from 143.3 to 21 C (case II). An integrated computer code is used for the simulation of the damage progression. Results show that damage initiation begins at low load level, with matrix cracking at the 0 deg. (bottom and top) plies, fiber fracture at the bottom (0 deg.) ply and interply delamination at the top (0 deg. ) ply. Increasing the applied pressure, the damage growth is expended resulting in fracture through the thickness of the structure. At this stage, 90 percent of the plies damage at applied pressure 15.306 MPa for the case I and 15.036 MPa for the case II. After this stage the cracks propagate rapidly and the structure collapses.

Gotsis, Pascalis K.↗
NASA NTRS1999

A One Dimensional, Time Dependent Inlet/Engine Numerical Simulation for Aircraft Propulsion Systems

The NASA Lewis Research Center (LeRC) and the Arnold Engineering Development Center (AEDC) have developed a closely coupled computer simulation system that provides a one dimensional, high frequency inlet/engine numerical simulation for aircraft propulsion systems. The simulation system, operating under the LeRC-developed Application Portable Parallel Library (APPL), closely coupled a supersonic inlet with a gas turbine engine. The supersonic inlet was modeled using the Large Perturbation Inlet (LAPIN) computer code, and the gas turbine engine was modeled using the Aerodynamic Turbine Engine Code (ATEC). Both LAPIN and ATEC provide a one dimensional, compressible, time dependent flow solution by solving the one dimensional Euler equations for the conservation of mass, momentum, and energy. Source terms are used to model features such as bleed flows, turbomachinery component characteristics, and inlet subsonic spillage while unstarted. High frequency events, such as compressor surge and inlet unstart, can be simulated with a high degree of fidelity. The simulation system was exercised using a supersonic inlet with sixty percent of the supersonic area contraction occurring internally, and a GE J85-13 turbojet engine.

Doug Garrard↗
NASA NTRS1989

Development and simulation study of a new inverse-pinch high Coulomb transfer switch

The inverse-pinch plasma switch was studied using a computer simulation code. The code was based on a 2-D, 2-temperature magnetohydrodynamic (MHD) model. The application of this code was limited to the disk-type inverse-pinch plasma switch. The results of the computer analysis appear to be in agreement with the experimental results when the same parameters are used. An inverse-pinch plasma switch for closing has been designed and tested for high-power switching requirements. An azimuthally uniform initiation of breakdown is a key factor in achieving an inverse-pinch current path in the switch. Thus, various types of triggers, such as trigger pins, wire-brush, ring trigger, and hypocycloidal-pinch (HCP) devices have been tested for uniform breakdown. Recently, triggering was achieved by injection of a plasma-ring (plasma puff) that is produced separately with hypocycloidal-pinch electrodes placed under the cathode of the main gap. The current paths at switch closing, initiated by the injection of a plasma-ring from the HCP trigger are azimuthally uniform, and the local current density is significantly reduced, so that damage to the electrodes and the insulator surfaces is minimized. The test results indicate that electron bombardment on the electrodes and the insulator surfaces is minimized. The test results indicate that electron bombardment on the electrodes is four orders of magnitude less than that of a spark-gap switch for the same switching power. Indeed, a few thousand shots with peak current exceeding a mega-ampere and with hold-off voltage up to 20 kV have been conducted without showing measurable damage to the electrodes and insulators.

Choi, Sang H.↗