Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffraction optics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Influence of Hydrogen Plasma Treatment Time to Si:H Layer Deposition Time Ratio on the Properties of Layer-by-Layer Deposited Hydrogenated Silicon (Si:H) Thin Films

Hydrogenated silicon (Si-H) thin films were deposited from a mixture of pure silane (SiH{sub 4}) and hydrogen (H{sub 2}) gases in a home-built plasma enhanced chemical vapour deposition (PECVD) system using the layer-by-layer (LBL) deposition technique. In the LBL process, the deposition was performed by periodically alternating the deposition of Si:H layer with the hydrogen treatment process of the growth surface. In this work, the effects of the H plasma treatment time to Si-H layer growth time ratio on the film properties were studied. The LBL deposited Si-H films studied in this work were deposited using different Si-H layer growth times ranging from 2 minutes to 7 minutes with the hydrogen plasma treatment time on the growth surface fixed at 3 minutes. Optical transmission spectroscopy, X-ray diffraction (XRD), micro-Raman scattering spectroscopy, Fourier transform infrared (FTIR) spectroscopy and atomic force microscopy (AFM) measurements were done on these films to investigate the optical, structural and morphological properties of the films. The films deposited by this technique produced the highest deposition rate of 6.3 A ring /s when the growth time of the Si-H layer was fixed at 5 minutes. These films were amorphous in structure and had large optical energy gaps irrespective of the Si-H layer deposition time. High concentration of cone-like structures was observed in the AFM images for the films deposited using the higher Si-H layer deposition times.

36 MATERIALS SCIENCE↗

Performance of a MEMS-base Adaptive Optics Optical Coherency Tomography System

We have demonstrated that a microelectrical mechanical systems (MEMS) deformable mirror can be flattened to < 1 nm RMS within controllable spatial frequencies over a 9.2-mm aperture making it a viable option for high-contrast adaptive optics systems (also known as Extreme Adaptive Optics). The Extreme Adaptive Optics Testbed at UC Santa Cruz is being used to investigate and develop technologies for high-contrast imaging, especially wavefront control. A phase shifting diffraction interferometer (PSDI) measures wavefront errors with sub-nm precision and accuracy for metrology and wavefront control. Consistent flattening, required testing and characterization of the individual actuator response, including the effects of dead and low-response actuators. Stability and repeatability of the MEMS devices was also tested. An error budget for MEMS closed loop performance will summarize MEMS characterization.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

SiC lightweight telescopes for advanced space applications. I - Mirror technology

A SiC based telescope is an extremely attractive emerging technology which offers the lightweight and stiffness features of beryllium, the optical performance of glass to diffraction limited visible resolution, superior optical/thermal stability to cryogenic temperatures, and the cost advantages of an aluminum telescope. SSG has developed various SiC mirrors with and without a silicon coating and tested these mirrors over temperature ranges from +50 C to -250 C. Our test results show less than 0.2 waves P-V in visible wavefront change and no hysteresis over this wide temperature range. Several SSG mirrors are representative of very lightweight SiC/Si mirrors including (1) a 9 cm diameter, high aspect ratio mirror weighing less than 30 grams and (2) a 23 cm diameter eggcrated mirror weighing less than 400 grams. SSG has also designed and analyzed a 0.6 meter SiC based, on axis, three mirror reimaging telescope in which the primary mirror weighs less than 6 kg and a 0.5 meter GOES-like scan mirror. SSG has also diamond turned several general aspheric SiC/Si mirrors with excellent cryo optical performance.

Anapol, Michael I.↗

Diffraction analysis and evaluation of several focus- and track-error detection schemes for magneto-optical disk systems

A commonly used tracking method on pre-grooved magneto-optical (MO) media is the push-pull technique, and the astigmatic method is a popular focus-error detection approach. These two methods are analyzed using DIFFRACT, a general-purpose scalar diffraction modeling program, to observe the effects on the error signals due to focusing lens misalignment, Seidel aberrations, and optical crosstalk (feedthrough) between the focusing and tracking servos. Using the results of the astigmatic/push-pull system as a basis for comparison, a novel focus/track-error detection technique that utilizes a ring toric lens is evaluated as well as the obscuration method (focus error detection only).

Bernacki, Bruce E.↗

Fresnel Lenses for Wide-Aperture Optical Receivers

Wide-aperture receivers for freespace optical communication systems would utilize Fresnel lenses instead of conventional telescope lenses, according to a proposal. Fresnel lenses weigh and cost much less than conventional lenses having equal aperture widths. Plastic Fresnel lenses are commercially available in diameters up to 5 m large enough to satisfy requirements for aperture widths of the order of meters for collecting sufficient light in typical long-distance free-space optical communication systems. Fresnel lenses are not yet suitable for high-quality diffraction-limited imaging, especially in polychromatic light. However, optical communication systems utilize monochromatic light, and there is no requirement for high-quality imaging; instead, the basic requirement for an optical receiver is to collect the incoming monochromatic light over a wide aperture and concentrate the light onto a photodetector. Because of lens aberrations and diffraction, the light passing through any lens is focused to a blur circle rather than to a point. Calculations for some representative cases of wide-aperture non-diffraction-limited Fresnel lenses have shown that it should be possible to attain blur-circle diameters of less than 2 mm. Preferably, the blur-circle diameter should match the width of the photodetector. For most high-bandwidth communication applications, the required photodetector diameters would be about 1 mm. In a less-preferable case in which the blur circle was wider than a single photodetector, it would be possible to occupy the blur circle with an array of photodetectors. As an alternative to using a single large Fresnel lens, one could use an array of somewhat smaller lenses to synthesize the equivalent aperture area. Such a configuration might be preferable in a case in which a single Fresnel lens of the requisite large size would be impractical to manufacture, and the blur circle could not be made small enough. For example one could construct a square array of four 5-m-diameter Fresnel lenses to obtain the same light-collecting area as that of a single 10-m-diameter lens. In that case (see figure), the light collected by each Fresnel lens could be collimated, the collimated beams from the four Fresnel lenses could be reflected onto a common offaxis paraboloidal reflector, and the paraboloidal reflector would focus the four beams onto a single photodetector. Alternatively, detected signal from each detector behind each lens would be digitized before summing the signals.

Hemmati, Hamid↗

Astronomical X-Ray Optics Using Mono-Crystalline Silicon: High Resolution, Light Weight, and Low Cost

X-ray astronomy critically depends on X-ray optics. The capability of an X-ray telescope is largelydetermined by the point-spread function (PSF) and the photon-collection area of its mirrors, the same astelescopes in other wavelength bands. Since an X-ray telescope must be operated above the atmosphere inspace and that X-rays reflect only at grazing incidence, X-ray mirrors must be both lightweight and thin, bothof which add significant technical and engineering challenge to making an X-ray telescope. In this paper wereport our effort at NASA Goddard Space Flight Center (GSFC) of developing an approach to making an Xraymirror assembly that can be significantly better than the mirror assembly currently flying on the ChandraX-ray Observatory in each of the three aspects: PSF, effective area per unit mass, and production cost per uniteffective area. Our approach is based on the precision polishing of mono-crystalline silicon to fabricate thinand lightweight X-ray mirrors of the highest figure quality and micro-roughness, therefore, having thepotential of achieving diffraction-limited X-ray optics. When successfully developed, this approach will makeimplementable in the 2020s and 2030s many X-ray astronomical missions that are currently on the drawingboard, including sounding rocket flights such as OGRE, Explorer class missions such as STAR-X andFORCE, Probe class missions such as AXIS, TAP, and HEX-P, as well as large missions such as Lynx.

Zhang, William W.↗

High-pressure structural integrity and structural transformations of glass-derived nanocomposites: A review

A review of our recent and ongoing extensive high-pressure synchrotron X-ray diffraction and high-pressure optical spectroscopy studies of nanocrystalline composites is presented. These heterophased, nano-architectured composites consist of amorphous matrices with dispersed nanocrystals or quantum dots. We show how besides compositional variations, additional tuning of these glass-derived nanocomposites can be done by exploiting elevated pressure. We examine stability and pressure-driven phase transitions occurring in nanocrystals as well as structural changes occurring in the glass matrix. Finally, we discuss the influence of the glass matrix of a composite on the structural transformations occurring in the embedded nanocrystals.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of annealing on the nonequilibrium carrier lifetime in GaAs grown at low temperatures

GaAs samples grown by molecular-beam epitaxy at low (230 Degree-Sign C) temperatures are investigated. One of the samples is subjected to aftergrowth annealing at 600 Degree-Sign C. Using an unconventional pump-probe scheme for measuring the dynamic variation in the light refractive index, the nonequilibrium charge-carrier lifetime (275 {+-} 30 fs before annealing) is determined. Such a short carrier lifetime in the unannealed material is due to the high concentration of point defects, mainly As{sub Ga} antisite defects. According to X-ray diffraction and steady-state optical absorption data, the As{sub Ga} concentration in the samples is 3 Multiplication-Sign 10{sup 19} cm{sup -3}, which corresponds to an arsenic excess of 0.26 at %. Upon annealing at 600 Degree-Sign C, the superstoichiometric As defects self-organize and form As nanoinclusions in the GaAs crystal matrix. It is shown that in this case the nonequilibrium charge-carrier lifetime increases to 452 {+-} 5 fs. This lifetime is apparently ensured by the capture of non-equilibrium charge carriers at metal As nanoinclusions.

36 MATERIALS SCIENCE↗

A comparative study of electronic and structural properties of polycrystalline and epitaxial magnetron-sputtered ZnO:Al and Zn{sub 1-x}Mg{sub x}O:Al Films—Origin of the grain barrier traps

Homoepitaxial and heteroepitaxial ZnO, ZnO:Al, and Zn{sub 1-x}Mg{sub x}O:Al films have been grown by magnetron sputtering from ceramic targets at substrate temperatures between 200 °C and 500 °C. We studied the relation between the electronic transport and structural properties for the epitaxially grown films and compared it to the properties of polycrystalline films by means of X-ray diffraction, transmission electron microscopy and optical reflectance and transmittance measurements. The results show that the epitaxial growth of ZnO:Al and Zn{sub 1-x}Mg{sub x}O:Al thin films, which has been observed for nearly all films prepared on single crystalline substrates, will not significantly improve the electronic transport properties in comparison to polycrystalline films unless the grain boundaries are eliminated completely. The grain boundary defect densities of about 3 × 10{sup 13} cm{sup −2} are nearly independent on the structural quality of the different polycrystalline, hetero- and homoepitaxial films. This clearly proves that the grain boundary defects are not caused by crystallographic defects, but, most probably, by the dopant aluminium.

36 MATERIALS SCIENCE↗

Photon up-conversion production in Tb{sup 3+}–Yb{sup 3+} co-doped CaF{sub 2} phosphors prepared by combustion synthesis

Graphical abstract: Up-conversion luminescence from Tb{sup 3+} obtained by energy transfer from Yb{sup 3+} pairs in CaF{sub 2} powder prepared by combustion synthesis. - Highlights: • Calcium fluoride (CaF{sub 2}) powders were prepared by combustion synthesis. • Rare-earth ions doped in this material were found in interstitial sites. • Cooperative up-conversion was observed in Tb{sup 3+}:Yb{sup 3+}:CaF{sub 2} powder. • Energy transfer between Tb{sup 3+} and pairs of Yb{sup 3+} was analyzed using rate equations. - Abstract: Calcium fluoride (CaF{sub 2}) crystalline powders were successfully prepared by the combustion synthesis method. The powder material containing luminescent rare-earth ions, more specifically terbium (Tb{sup 3+}) and ytterbium (Yb{sup 3+}), was studied by X-ray diffraction, scanning electronic microscopy and optical spectroscopy. These ions are allocated in charge compensated interstitial positions of tetragonal (C{sub 4v}) and trigonal (C{sub 3v}) symmetry sites of the cubic (O{sub h}) CaF{sub 2} lattice. Up-conversion (UC) luminescence in Tb{sup 3+} was achieved using a low power diode laser operating at 975 nm. Tb{sup 3+} is insensitive to near-infrared radiation but UC can be achieved via energy transfer from pairs of Yb{sup 3+} ions to Tb{sup 3+} ions. The UC luminescence dynamics of Tb{sup 3+} was used to study the energy transfer mechanism.

36 MATERIALS SCIENCE↗

MEMS-tunable dielectric metasurface lens

Varifocal lenses, conventionally implemented by changing the axial distance between multiple optical elements, have a wide range of applications in imaging and optical beam scanning. The use of conventional bulky refractive elements makes these varifocal lenses large, slow, and limits their tunability. Metasurfaces, a new category of lithographically defined diffractive devices, enable thin and lightweight optical elements with precisely engineered phase profiles. Here we demonstrate tunable metasurface doublets, based on microelectromechanical systems (MEMS), with more than 60 diopters (about 4%) change in the optical power upon a 1-μm movement of one metasurface, and a scanning frequency that can potentially reach a few kHz. They can also be integrated with a third metasurface to make compact microscopes (~1 mm thick) with a large corrected field of view (~500 μm or 40 degrees) and fast axial scanning for 3D imaging. This paves the way towards MEMS-integrated metasurfaces as a platform for tunable and reconfigurable optics.

42 ENGINEERING↗

Synthesis, characterization and alloying of Cu{sub 2}ZnSnQ{sub 4} (Q=S, Se and Te) nanocrystals

Cu{sub 2}ZnSnQ{sub 4} nanocrystals, with Q=S, Se and Te, were grown by a colloidal synthetic approach and characterized by X-ray diffraction, transmission electron microscopy, and optical absorbance. We also demonstrate that doping and alloying at the nanoscale is possible by this approach. The results are discussed in terms of developing a standardized synthetic approach for the synthesis of quaternary nanocrystals, including doping and alloying, in order to allow for bottom-up processing of these materials for energy-related applications. - Graphical abstract: We developed a standardized synthetic approach for the synthesis of quaternary stannite Cu{sub 2}ZnSnQ{sub 4} nanocrystals with Q=S, Se and Te including doping, alloying and Te-based compositions for the first time, in order to allow for bottom-up processing of these materials for energy-related applications. - Highlights: • Cu{sub 2}ZnSnQ{sub 4} nanocrystals, with Q=S, Se and Te, were grown by a colloidal synthetic approach. • Doping and alloying of these quaternary nanocrystals were demonstrated for the first time. • This standardized synthetic approach allows for bottom-up processing of these materials for energy-related applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A WISER way for simulating the performance of gratings

Soft X-ray monochromators for synchrotron radiation sources have been continuously developed over the years, improving energy resolution and stability. Great effort has been made in improving the surface quality of the optics involved, reaching values permitting diffraction-limited images. Still, one problem has not been solved, nor fully understood, yet: groove placing errors. Nowadays, these are one of the major factors responsible for resolving the power reduction of diffraction-gratings-based X-ray monochromators. Despite decades of use of gratings, there is not yet a universally established method for predicting and simulating the effect of groove placing errors on monochromator performance. This is especially important in the new scenario of high-coherent X-ray sources, i.e. diffraction-limited storage rings and free-electron lasers. To address this problem, in this article an approach based on WISER (Wavefront propagatIon Simulation codE libRary) is presented. WISER is a physical optics simulation package, also available in the user-friendly Orange Synchrotron Radiation Suite – OASYS. Even though it was originally conceived to assess the focusing performance of X-ray mirrors in the presence of height defects, it perfectly simulates the performance of a periodic (or quasi-periodic) structure like a diffraction grating. In this article, the way to use WISER and its application to a specific case, e.g. the design of a monochromator for the upgrade of a beamline at the Advanced Light Source, are shown. A simple rule for estimating how well the grooves are placed on a grating, based on calculation of the Strehl ratio, is also presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Mixed magnetic phases in Co{sub 3}O{sub 4} nanoparticles synthesized by co-precipitation method

In the present manuscript, Co{sub 3}O{sub 4} nanoparticles have been synthesized with the help of co-precipitation method and studied the structural, optical and magnetic properties. X ray diffraction analysis of the synthesized samples reveals the formation of single phase cubic spinel structure with the space group Fd-3m. FESEM and TEM results indicate the formation of nano-sized particles. The optical measurement reveals the two band gaps ∼2.77 and 1.67 eV in the sample. Magnetic measurement shows weak ferromagnetic interaction in Co{sub 3}O{sub 4} along with usual paramagnetic nature at room temperature. However, at low temperatures the sample shows antiferromagnetic interaction. The correlation between the structural and observed magnetic and optical properties of Co{sub 3}O{sub 4} nanoparticles will be described and discussed in this paper.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Shape error analysis for reflective nano focusing optics

Focusing performance of reflective x-ray optics is determined by surface figure accuracy. Any surface imperfection present on such optics introduces a phase error in the outgoing wave fields. Therefore converging beam at the focal spot will differ from the desired performance. Effect of these errors on focusing performance can be calculated by wave optical approach considering a coherent wave field illumination of optical elements. We have developed a wave optics simulator using Fresnel-Kirchhoff diffraction integral to calculate the mirror pupil function. Both analytically calculated and measured surface topography data can be taken as an aberration source to outgoing wave fields. Simulations are performed to study the effect of surface height fluctuations on focusing performances over wide frequency range in high, mid and low frequency band. The results using real shape profile measured with long trace profilometer (LTP) suggest that the shape error of {lambda}/4 PV (peak to valley) is tolerable to achieve diffraction limited performance. It is desirable to remove shape error of very low frequency as 0.1 mm{sup -1} which otherwise will generate beam waist or satellite peaks. All other frequencies above this limit will not affect the focused beam profile but only caused a loss in intensity.

43 PARTICLE ACCELERATORS↗