Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel performance analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

An analysis of aircraft accidents involving fires

All U. S. Air Carrier accidents between 1963 and 1974 were studied to assess the extent of total personnel and aircraft damage which occurred in accidents and in accidents involving fire. Published accident reports and NTSB investigators' factual backup files were the primary sources of data. Although it was frequently not possible to assess the relative extent of fire-caused damage versus impact damage using the available data, the study established upper and lower bounds for deaths and damage due specifically to fire. In 12 years there were 122 accidents which involved airframe fires. Eighty-seven percent of the fires occurred after impact, and fuel leakage from ruptured tanks or severed lines was the most frequently cited cause. A cost analysis was performed for 300 serious accidents, including 92 serious accidents which involved fire. Personal injury costs were outside the scope of the cost analysis, but data on personnel injury judgements as well as settlements received from the CAB are included for reference.

Lucha, G. V.↗

Application of Laminar Flow Control Technology to Long-Range Transport Design

The impact of laminar flow control (LFC) technology on aircraft structural design concepts and systems was discussed and the corresponding benefits were shown in terms of performance and fuel economy. Specific topics discussed include: (1) recent advances in laminar boundary layer development and stability analysis techniques in terms of suction requirements and wing suction surface design; (2) validation of theory and realistic simulation of disturbances and off-design conditions by wind tunnel testing; (3) compatibility of aerodynamic design of airfoils and wings with LFC requirements; (4) structural alternatives involving advanced alloys or composites in combinations made possible by advanced materials processing and manufacturing techniques; (5) addition of suction compressor and drive units and their location on the aircraft; and (6) problems associated with operation of LFC aircraft, including accumulation of insects at low altitudes and environmental considerations.

Gratzer, L. B.↗

Development of a helicopter rotor/propulsion system dynamics analysis

A time-domain analysis of coupled engine/drive train/rotor dynamics of a twin-engine, single main rotor helicopter model has been performed. The analysis incorporates an existing helicopter model with nonlinear simulations of a helicopter turboshaft engine and its fuel controller. System dynamic behavior is studied using the resulting simulation which included representations for the two engines and their fuel controllers, drive system, main rotor, tail rotor, and aircraft rigid body motions. Time histories of engine and rotor RPM response to pilot control inputs are studied for a baseline rotor and propulsion system model. Sensitivity of rotor RPM droop to fuel controller gain changes and collective input feed-forward gain changes are studied. Torque-load-sharing between the two engines is investigated by making changes in the fuel controller feedback paths. A linear engine model is derived from the nonlinear engine simulation and used in the coupled system analysis. This four-state linear engine model is then reduced to a three-state model. The effect of this simplification on coupled system behavior is shown.

Warmbrodt, W.↗

A model to assess the Mars Telecommunications Network relay robustness

The relatively long mission durations and compatible radio protocols of current and projected Mars orbiters have enabled the gradual development of a heterogeneous constellation providing proximity communication services for surface assets. The current and forecasted capability of this evolving network has reached the point that designers of future surface missions consider complete dependence on it. Such designers, along with those architecting network requirements, have a need to understand the robustness of projected communication service. A model has been created to identify the robustness of the Mars Network as a function of surface location and time. Due to the decade-plus time horizon considered, the network will evolve, with emerging productive nodes and nodes that cease or fail to contribute. The model is a flexible framework to holistically process node information into measures of capability robustness that can be visualized for maximum understanding. Outputs from JPL's Telecom Orbit Analysis Simulation Tool (TOAST) provide global telecom performance parameters for current and projected orbiters. Probabilistic estimates of orbiter fuel life are derived from orbit keeping burn rates, forecasted maneuver tasking, and anomaly resolution budgets. Orbiter reliability is estimated probabilistically. A flexible scheduling framework accommodates the projected mission queue as well as potential alterations.

Mars Telecommunications Orbiter (MTO)↗

An Assessment of NASA Aeropropulsion Technologies: A System Study

Aviation industry s robust growth rate has given rise to growing concerns about the contribution that aviation emissions will make to local air quality and global climate change. Over the last several years, NASA has been engaged in the development of aeropropulsion technologies with specific objectives to reduce aircraft emissions. A system analysis was performed to evaluate the potential impact of these propulsion technologies on aircraft CO2 (directly proportional to fuel burn) and NOx reductions. A large subsonic aircraft, with two 396-kN thrust (85,000-pound) engines was chosen for the study. Performance benefit estimates are presented for each technology, with a summary of potential emissions reduction possible from the development of these technologies. The results show that NASA s aeropropulsion technologies have the potential to significantly reduce the CO2 and NO(x) emissions. The results are used to support informed decision-making on the development of aeropropulsion technology portfolio for CO2 and NO(x) reductions.

Tong, Michael T.↗

In-Pile testing of CrN, TiAIN, and AlCrN coatings on Zircaloy cladding in the Halden reactor - 2016-0011

CrN coating came out as superior and remained completely intact after the irradiation, as evidenced by SEM analysis. Based on these promising results, an in-pile experiment with coated Zircaloy claddings (containing fuel) was performed in the Halden reactor in PWR conditions in 2014. The experimental rig contained four Zircaloy-4-clad fuel rods-three coated (CrN, TiAlN, and AlCrN) and one uncoated. Due to a mechanical deformation of tubes for cooling water within the rig, the fuel rods were insufficiently cooled, resulting in a higher-than-normal cladding temperature. Nevertheless, an SEM examination showed that the CrN coating largely remained intact apart from several local spots where the coating had cracked or disappeared. Underneath the cracked coating, oxide formation was observed in the Zircaloy-4 cladding. The TiAlN and AlCrN coatings both disappeared after the irradiation. (authors)

36 MATERIALS SCIENCE↗

Coupled neutronic-thermal-hydraulic simulations of the European SFR core

Within the European SFR (Sodium-cooled Fast Reactor) - Safety Measures Assessment and Research Tools (ESFR-SMART) project, steady-state coupled simulation of the ESFR core has been performed using several core analysis packages, with the objective of quantifying the coupling effect. Focus is on the fuel Doppler effect and coolant expansion effect. Standalone neutronics calculations in TRACE/PARCS (PSI), DYN3D (HZDR) and WIMS (Jacobs) showed superb agreement with the reference Serpent power distribution (root mean square - rms discrepancies of 1.3%, 1.5% and 0.7% respectively). Results for COUNTHER (CIEMAT) were also in reasonable agreement, but with a somewhat higher discrepancy of 3.7%. Temperature distributions from thermal-hydraulic calculations were also compared and are found to be in good agreement. The effect of Doppler and coolant density feedback on core power distribution was predicted by TRACE/PARCS, DYN3D and WIMS to be between 0.4% and 0.8% rms difference in assembly powers. Reactivity coefficients for perturbations in the inlet temperature, flow rate and core power were shown to be negative for these three codes, with values of roughly -0.5 pcm/C. degree, -0.3 pcm/C. degree and -3.5 pcm/C. degree respectively. A preliminary investigation of differential thermal expansion effects indicates that this may have a significant effect on core power distribution of a few %, greater than anticipated a priori and may warrant inclusion in coupled core analysis to ensure the accurate calculation of power distributions. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Hybrid Electric Turboprop Commercial Freighter Opportunity

As the era of electric and hybrid electric aviation is dawning, we have the opportunity to reduce cost, energy use, and emissions of air transportation. In this paper, the case is made for the potential efficiency benefits that can be gained with hybrid electric propulsion. Initial economic, mission profile, and propulsion system concepts for a large turboprop aircraft we designate as the Hybrid Electric Turboprop Commercial Freighter (HETCOF) are presented. Market analysis shows HETCOF has the potential to serve a large market share, but the cost requirements for a new purpose built are challenging relative to the repurposed narrow body aircraft currently operating in the market. Comparing HETCOF to a genericized large turboprop freighter the payload capacity is reduced by 40% for the TRL 5+ configuration but is equivalent to the baseline for the TRL 1-2 configuration. All HETCOF configurations result in increased efficiency and subsequent block fuel, block energy, and block emissions reductions. An integrated power/thermal/and energy storage system is presented and analyzed using key performance parameters to estimate weights and losses at three technology readiness levels. Analysis shows that for a concept like this to have economic and energy benefits, many TRL 1-2 level technologies would be needed. Relevant ARPA-E programs and NASA technologies being developed to enable the benefit are also described. The most significant result of this paper is that the HETCOF concept can close with reduced fuel burn, energy use, and emissions while retaining some or all of the cargo capability of the baseline aircraft across TRL level assumptions, which enables this platform to be used for near term introduction with increasing benefits as technology matures.

Ralph H Jansen↗

Diffusion behaviors between metallic fuel alloys with Pd addition and Fe

Fission product lanthanides (Lns) in metallic fuel is the primary cause of fuel-cladding chemical interaction (FCCI). Palladium (Pd) is being explored as a potential additive to reduce or mitigate FCCI by forming stable Pd-Ln compounds. The current study is an investigation of diffusion behaviors between UZrPd, UZrPdLn, UPuZrPd, and UPuZrPdLn alloys (Ln = 53Nd-25Ce-16Pr-6La wt. %) and iron (Fe). Diffusion couple tests were performed followed by microstructural analysis using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It is found that the diffusion of Fe into the fuel is reduced by PdZr2 precipitates randomly dispersed throughout the fuel matrix. Ln-Pd compounds form in UZrPdLn alloys, and (Ln,Pu)Pd forms in the UPuZrPdLn alloy. In both diffusion couples with Ln, small amounts of Lns are diffusing into the Fe. This could be due to small amounts of dissolved Lns in the precipitates, or could be due to the Ln-Pd compounds decomposing. In either case, diffusion caused by Lns is greatly reduced.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High resolution neutron imaging of water in the polymer electrolyte membrane

To achieve a deeper understanding of water transport and performance issues associated with water management, we have conducted in situ water examinations to help understand the effects of components and operation. High Frequency Resistance (HFR), AC Impedance and neutron radiography were used to measure water content in operating fuel cells under various operating conditions. Variables examined include: sub-freezing conditions, inlet relative humidities, cell temperature, current density and response transients, different flow field orientations and different component materials (membranes, GDLs and MEAs). Quantification of the water within the membrane was made by neutron radiography after equilibration to different humidified gases, during fuel cell operation and in hydrogen pump mode. The water content was evaluated in bare Nafion{reg_sign} membranes as well as in MEAs operated in both fuel cell and H{sub 2} pump mode. These in situ imaging results allow measurement of the water content and gradients in the PEFC membrane and relate the membrane water transport characteristics to the fuel cell operation and performance under disparate materials and operational combinations. Flow geometry makes a large impact on MEA water content. Higher membrane water with counter flow was measured compared with co-flow for sub-saturated inlet RH's. This correlates to lower HFR and higher performance compared with co-flow. Higher anode stoichiometry helps remove water which accumulates in the anode channels and GDL material. Cell orientation was measured to affect both the water content and cell performance. While membrane water content was measured to be similar regardless of orientation, cells with the cathode on top show flooding and loss of performance compared with similarly operated cells with the anode on top. Transient fuel cell current measurements show a large degree of hysteresis in terms of membrane hydration as measured by HFR. Current step transients from 0.01 A cm{sup -2} to 0.68 A cm{sup -2} consistently show PEM wetting occurring within 5 to 20 sec. Whereas the PEM drying response to the reverse step transient of 0.68 A cm{sup -2} to 0.01 A cm{sup -2}, takes several minutes. The observed faster wetting response is due to reaction water being produced in the cathode and back diffusing into the membrane. The slower PEM drying is due to the water slowly being removed out of the wetted GDLs. This rate of removal of water and hence the PEM hydration level was found to be influenced strongly by the PTFE loadings in the GDL substrate and Microporous layer (MPL). The drying of the membrane is influenced by both the anode and cathode GDL PTFE loadings. Lower PTFE loading in the anode GDL leads to better membrane hydration probably due to the easier incorporation of water from the anode GDL into the membrane. Similarly a lower PTFE loading in the cathode GDL also results in better membrane hydration probably due to the better water retention properties (less hydrophobic) of this GDL. Fuel cells operated isothermal at sub-freezing temperatures show gradual cell performance decay over time and eventually drops to zero. AC impedance analysis indicates that losses are initially due to increasing charge transfer resistance. After time, the rate of decay accelerates rapidly due to mass transport limitations. High frequency resistance also increases over time and is a function of the initial membrane water content. These results indicate that catalyst layer ice formation is influenced strongly by the MEA and is responsible for the long-term degradation of fuel cells operated at sub-freezing temperatures. Water distribution measurements indicate that ice may be fonning mainly in the GDLs at -10 C but are concentrated in the catalyst layer at -20 C.

08 HYDROGEN↗

Evaluation of the use of color-set geometry during lattice physics constants generation for boiling water reactor simulation

Current methods for BWR nuclear design and analysis consist of using lattice physics neutron transport methods to generate the two-group homogenized cross-sections that are then used in a nodal diffusion theory code. The lattice transport solutions are performed for a single assembly with reflective boundary conditions, which is a practical approximation. A method is developed to account for assembly exposure distributions (environment) in the core within the lattice transport calculations with the use of color-sets (2x2) geometry. The loading pattern is examined and an appropriate number of characteristic color-set cells are selected for analysis. Treatment of the co-resident exposed fuel within this method is also presented. The calculation process was followed for a recent BWR cycle design with comparisons being performed on both a lattice and core-wide basis to evaluate the proposed method. The lattice based comparisons show noticeable differences in the pin power distribution predictions, which require further investigation to see how this translates into core performance calculations. The core-wide comparisons show minor differences and are generally in a good agreement, which is expected with this small perturbation. A slight improvement was noticed in the reduction of the power distribution uncertainty. However, given the additional amount of work and computer run time increase, further evaluation, especially of core pin power predictions, is needed to consider this method for production level design and safety analysis calculations. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A Validation Study of Pin Heat Transfer for MOX Fuel Based on the IFA-597 Experiments

Abstract The IFA-597 (Integrated Fuel Assessment) experiments from the International Fuel Performance Experiments (IFPE) database were designed to study the thermal behavior of mixed oxide (MOX) fuel and the effects of an annulus on fission gas release in light-water-reactor fuel. An evaluation of nuclear fuel pin heat transfer in the FRAPCON-3.4 and Exnihilo codes for MOX fuel systems was performed, with a focus on the first 20 time steps ( 6 GWd/MT(iHM)) for explicit comparison between the codes. In addition, sensitivity studies were performed to evaluate the effect of the radial power shape and approximations to the geometry to account for the thermocouple hole, dish, and chamfer. The analysis demonstrated relative agreement for both solid (rod 1) and annular (rod 2) fuel in the experiment, demonstrating the accuracy of the codes and their underlying material models for MOX fuel, while also revealing a small energy loss artifact in how gap conductance is currently handled in Exnihilo for chamfered fuel pellets. The within-pellet power shape was shown to significantly impact the predicted centerline temperatures. This has provided an initial benchmarking of the pin heat transfer capability of Exnihilo for MOX fuel with respect to a well-validated nuclear fuel performance code.

Phillippe, Aaron M↗

Drying and Analysis of Aluminum (Oxy)hydroxide Films for Dry Storage of Aluminum-Clad Spent Nuclear Fuels

In aluminum-clad spent nuclear fuels, an (oxy)hydroxide layer on the surface of the cladding hosts chemisorbed water formed during reactor and post-discharge exposure to water. Any residual water is susceptible to generating hydrogen via radiolysis, which can be a risk associated with dry fuel storage. Engineering-scale forced helium dehydration (FHD) and vacuum drying tests were conducted on mock-up fuel assemblies that included corroded aluminum surrogate plates to assess the removal of bulk and chemisorbed water. Thermogravimetric analysis was performed on samples of the surrogate plates, both undried control samples used to determine onset temperatures associated with a phase change occurring in the oxide layer and samples from drying tests used to determine the effectiveness of each drying method. Both vacuum drying and FHD processes were capable of removing bulk water. However, FHD was determined to provide additional drying capabilities, including partial removal of chemisorbed water from bayerite due to the higher temperatures during drying. In conclusion, the temperature threshold for partial dehydroxylation of the oxide layer was determined to be around 220°C, meaning any drying methods attempting to remove chemisorbed water must exceed 220°C.

chemisorbed water↗

Supply Chain Sustainability Analysis of Fast Pyrolysis and Hydrotreating Bio-Oil to Produce Hydrocarbon Fuels

The Department of Energy’s (DOE) Bioenergy Technology Office (BETO) aims at developing and deploying technologies to transform renewable biomass resources into commercially viable, high-performance biofuels, bioproducts and biopower through public and private partnerships (DOE, 2015). BETO and its national laboratory teams conduct in-depth techno-economic assessments (TEA) of technologies to produce biofuels. These assessments evaluate feedstock production, logistics of transporting the feedstock, and conversion of the feedstock to biofuel. There are two general types of TEAs. A design case is a TEA that outlines a target case for a particular biofuel pathway. It enables identification of data gaps and research and development needs, and provides goals and targets against which technology progress is assessed. On the other hand, a state of technology (SOT) analysis assesses progress within and across relevant technology areas based on actual experimental results relative to technical targets and cost goals from design cases, and includes technical, economic, and environmental criteria as available.

09 BIOMASS FUELS↗

Waste Stream Analyses for Nuclear Fuel Cycles

A high-level study was performed in Fiscal Year 2009 for the U.S. Department of Energy (DOE) Office of Nuclear Energy (NE) Advanced Fuel Cycle Initiative (AFCI) to provide information for a range of nuclear fuel cycle options (Wigeland 2009). At that time, some fuel cycle options could not be adequately evaluated since they were not well defined and lacked sufficient information. As a result, five families of these fuel cycle options are being studied during Fiscal Year 2010 by the Systems Analysis Campaign for the DOE NE Fuel Cycle Research and Development (FCRD) program. The quality and completeness of data available to date for the fuel cycle options is insufficient to perform quantitative radioactive waste analyses using recommended metrics. This study has been limited thus far to qualitative analyses of waste streams from the candidate fuel cycle options, because quantitative data for wastes from the front end, fuel fabrication, reactor core structure, and used fuel for these options is generally not yet available.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Safe Dissolution of High Flux Isotope Reactor Cores

The H-Canyon facility at the Savannah River Site is the U.S.A.’s only remaining full- scale chemical separations plant. H-Canyon maintains the capacity to safely and efficiently disposition a large inventory of excess nuclear material from across the Department of Energy (DOE) complex and used nuclear fuel from foreign and domestic research reactors. One such fuel that H-Canyon may dissolve is cores from the High Flux Isotope Reactor (HFIR). By employing realistic analysis, the need for administrative controls was eliminated. A new criticality modeling approach has eliminated the need for administrative controls for HFIR dissolution operations in H-Canyon. The primary upsets of concern are an over-mass event and an overconcentration event. Several initiating events were considered for each type of upset. Over-concentration events were deemed to be not credible by taking credit for the chemistry of acid consumption, i.e. there are not enough moles of acid to dissolve enough moles of uranium in order to reach a critical configuration. Over-mass events were deemed to be not credible by taking credit for the annular design of the fuel elements. By using realistic analysis, both types of upsets have been shown to be subcritical, and therefore administrative controls are not needed to prevent an inadvertent criticality. In this paper, the new methodology for performing criticality analyses for dissolving HFIR fuel elements will be presented, and the elimination of administrative controls will be discussed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Safe solution dissolution of high flux isotope reactor cores - 14490

The H-Canyon facility at the Savannah River Site is the U.S.A.'s only remaining full-scale chemical separations plant. H-Canyon maintains the capacity to safely and efficiently disposition a large inventory of excess nuclear material from across the Department of Energy (DOE) complex and used nuclear fuel from foreign and domestic research reactors. One such fuel that H-Canyon may dissolve is cores from the High Flux Isotope Reactor (HFIR). By employing realistic analysis, the need for administrative controls was eliminated. A new criticality modeling approach has eliminated the need for administrative controls for HFIR dissolution operations in H-Canyon. The primary upsets of concern are an over-mass event and an overconcentration event. Several initiating events were considered for each type of upset. Over-concentration events were deemed to be not credible by taking credit for the chemistry of acid consumption, i.e. there are not enough moles of acid to dissolve enough moles of uranium in order to reach a critical configuration. Over-mass events were deemed to be not credible by taking credit for the annular design of the fuel elements. By using realistic analysis, both types of upsets have been shown to be subcritical, and therefore administrative controls are not needed to prevent an inadvertent criticality. In this paper, the new methodology for performing criticality analyses for dissolving HFIR fuel elements will be presented, and the elimination of administrative controls will be discussed. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Using Calibrated Water Data for Preliminary Validation of the SRT Code for Advanced Reactors

Recent interest and corresponding progress worldwide regarding advanced nuclear reactors has renewed focus on their performance and related safety assessments. Specifically, the U.S. Nuclear Regulatory Commission has emphasized the importance of mechanistic approaches to source term analysis for advanced reactor licensing applications, which attempt to realistically account radionuclide transport and retention phenomena. Further model development is required due to the numerous and complex physical and chemical phenomena associated with mechanistic source term analyses. Reflecting the need for modeling advancement, Argonne National Laboratory developed a mechanistic source term analysis tool for sodium fast reactors. The Simplified Radionuclide Transport (SRT) code describes fuel pin failure (for simulating the initial condition at the point of fuel pin breach), bubble scrubbing, deposition, leakage and following environmental impact. In the current work, a validation study of the SRT bubble scrubbing model is performed using a water-loop experiment performed at the University of Wisconsin-Madison. Through the analysis, the approach and fundamental bubble scrubbing models in SRT, which examine the removal of aerosols within the bubble as it is transported through a pool, have been widely evaluated. The results of the assessment demonstrate a high level of agreement in the regions of greater aerosol size. In the parameter range of minimal aerosol removal, the simulation slightly underpredicts the experiment results; however, considering the scale of plots and huge uncertainties inherently included, the deviation can be judged to be minor and would produce a conservative result. In addition, uncertainty analysis has been further refined to reflect the experimental distribution of parameters including aerosol sizes, which induces a span of performance for each representative aerosol size. Based upon the initial validation results along with uncertainty effects, SRT is expected to provide meaningful insights for the analysis of bubble scrubbing. Future sodium-loop tests will provide further validation basis.

Kam, Dong Hoon↗