Search NASA⌕ Search

SEARCH · Search NASA

Results for “Large Eddy Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Comparison of wind farm control strategies under realistic offshore wind conditions: turbine quantities of interest

Abstract. Wind farm flow control is a strategy to increase the efficiency and therefore lower the levelized cost of energy of a wind farm. This is done using turbine settings such as the yaw angle, blade pitch angles, or generator torque to manipulate the flow behind the turbine, affecting downstream turbines in the farm. Two inherently different wind farm flow control methods have been identified in the literature: wake steering and wake mixing. This paper focuses on comparing the turbine quantities of interest between these methods for a simple two-turbine wind farm setup, while a companion article (Brown et al., 2025) focuses on the wake quantities of interest for a single wind turbine setup. Both papers use the same set of wind farm simulations based on high-fidelity large-eddy simulations (LESs) coupled with OpenFAST turbine models. First, precursor simulations are executed in order to match wind conditions measured with lidars in an offshore wind farm off the east coast of the USA. These measurements show general wind conditions that exhibit substantially higher vertical wind shear and veer than any of the LES studies performed with wind farm flow control strategies currently available in the literature. The precursors are used to evaluate the effectiveness of the control methods. In the LES, the wind veer leads to highly skewed wakes, which have considerable influence on the power uplift of wind farm flow control strategies. In addition to a baseline controller, four different control strategies, each of which uses either pitch or yaw control, are performed on the upstream turbine of a simple two-turbine wind farm. Assuming that the wind direction is known and constant over time, the simulations show that wake steering is generally the superior wind farm flow control strategy, considering both wind farm power production and turbine damage equivalent loads when substantial wind veer is present. This result is consistent over different wind speeds and wind directions. On the other hand, for similar wind conditions with lower veer, wake mixing was found to yield the highest power production, although at the expense of generally higher loads. This leads us to conclude that the effect of wind veer, which has so far not usually been considered, can not be neglected when determining the optimal wind farm flow control strategy.

17 WIND ENERGY↗

Wind farm structural response and wake dynamics for an evolving stable boundary layer: computational and experimental comparisons

Abstract. The wind turbine design process requires performing thousands of simulations for a wide range of inflow and control conditions, which necessitates computationally efficient yet time-accurate models, especially when considering wind farm settings. To this end, FAST.Farm is a dynamic-wake-meandering-based mid-fidelity engineering tool developed by the National Renewable Energy Laboratory targeted at accurately and efficiently predicting wind turbine power production and structural loading in wind farm settings, including wake interactions between turbines. This work is an extension of a study that addressed constructing a diurnal cycle evolution based on experimental data (Quon, 2024). Here, this inflow is used to validate the turbine structural and wake-meandering response between experimental data, FAST.Farm simulation results, and high-fidelity large-eddy simulation results from the coupled Simulator fOr Wind Farm Applications (SOWFA)–OpenFAST tool. The validation occurs within the nocturnal stable boundary layer when corresponding meteorological and turbine data are available. To this end, we compared the load results from FAST.Farm and SOWFA–OpenFAST to multi-turbine measurements from a subset of a full-scale wind farm. Computational predictions of blade-root and tower-base bending loads are compared to 10 min statistics of strain gauge measurements during 3.5 h of the evolving stable boundary layer, generally with good agreement. This time period coincided with an active wake-steering campaign of an upstream turbine, resulting in time-varying yaw positions of all turbines. Wake meandering was also compared between the computational solutions, generally with excellent agreement. Simulations were based on a high-fidelity precursor constructed from inflow measurements and using state-of-the-art mesoscale-to-microscale coupling.

17 WIND ENERGY↗

Ice Nucleation in Deep Convection

The processes controlling production of ice crystals in deep, rapidly ascending convective columns are poorly understood due to the difficulties involved with either modeling or in situ sampling of these violent clouds. A large number of ice crystals are no doubt generated when droplets freeze at about -40 C. However, at higher levels, these crystals are likely depleted due to precipitation and detrainment. As the ice surface area decreases, the relative humidity can increase well above ice saturation, resulting in bursts of ice nucleation. We will present simulations of these processes using a large-eddy simulation model with detailed microphysics. Size bins are included for aerosols, liquid droplets, ice crystals, and mixed-phase (ice/liquid) hydrometers. Microphysical processes simulated include droplet activation, freezing, melting, homogeneous freezing of sulfate aerosols, and heterogeneous ice nucleation. We are focusing on the importance of ice nucleation events in the upper part of the cloud at temperatures below -40 C. We will show that the ultimate evolution of the cloud in this region (and the anvil produced by the convection) is sensitive to these ice nucleation events, and hence to the composition of upper tropospheric aerosols that get entrained into the convective column.

Jensen, Eric↗

Multi‐Scale Temporal Variability of Turbulent Mixing During a Monsoon Intra‐Seasonal Oscillation in the Bay of Bengal: An LES Study

A process study using large‐eddy simulations is carried out to explore the dominant 1‐D processes that affect mixed layer (ML) properties during an event of summer Monsoon Intra‐seasonal Oscillations (MISO) in the Bay of Bengal (BOB). These simulations use realistic air‐sea fluxes and initial conditions that were collected during the summer 2018 MISO‐BOB field experiment to explore the roles of thermal inversion layer (TIL) and Langmuir turbulence (LT) in modulating ML properties. The simulations span an active period with heavy rain and strong winds and a break period with strong solar heat flux and little rain. The mixed layer depth (MLD), sea surface temperature (SST) and sea surface salinity (SSS) are most affected by the presence of near‐inertial oscillations, solar heating and precipitation, all of which occur at different timescales. The subsurface warming induced by the TIL reduces the SST variability at the MISO timescale when compared with the simulation without TIL. Comparison of simulations with and without LT indicates that LT enhances subsurface warming during the active phase and reduces diurnal SST modulation during the break phase. Finally, simulations with 1‐D mixing models show a wide disparity in the evolution of MLD, SST, and SSS.

54 ENVIRONMENTAL SCIENCES↗

Budget of Turbulent Kinetic Energy in a Shock Wave Boundary-Layer Interaction

Implicit large-eddy simulation (ILES) of a shock wave/boundary-layer interaction (SBLI) was performed. Quantities present in the exact equation of the turbulent kinetic energy transport were accumulated and used to calculate terms like production, dissipation, molecular diffusion, and turbulent transport. The present results for a turbulent boundary layer were validated by comparison with direct numerical simulation data. It was found that a longer development domain was necessary for the boundary layer to reach an equilibrium state and a finer mesh resolution would improve the predictions. In spite of these findings, trends of the present budget match closely with that of the direct numerical simulation. Budgets for the SBLI region are presented at key axial stations. These budgets showed interesting dynamics as the incoming boundary layer transforms and the terms of the turbulent kinetic energy budget change behavior within the interaction region.

shock wave/boundary-layer interaction↗

On the Settling Depth of Meltwater Escaping From Beneath Antarctic Ice Shelves

Antarctic glacial meltwater is thought to play an important role in determining large-scale Southern Ocean climate trends, yet recent modeling efforts have proceeded without a good understanding of how its vertical distribution in the water column is set. To rectify this, here we conduct new large-eddy simulations of the ascent of a buoyant meltwater plume after its escape from beneath an Antarctic ice shelf. We find that the meltwater’s settling depth is primarily a function of the buoyancy forcing per unit width of the source and the ambient stratification, consistent with the classical theory of turbulent buoyant plumes and in contrast to previous work that suggested an important role for centrifugal instability. Our results further highlight the significant role played by localized variability in stratification; this helps explain observed interannual variability in the vertical meltwater distribution near Pine Island Glacier. Because of the vast heterogeneity in mass loss rates and ambient conditions at different Antarctic ice shelves, a dynamic parameterization of meltwater settling depth may be crucial for accurately simulating high-latitude climate in a warming world; we discuss how this may be developed following this work, and where the remaining challenges lie.

Antarctic glacial meltwater↗

Contribution to the numerical study of turbulence in high intensity discharge lamps

We present in this paper a comparison between results obtained with a laminar and turbulent models for high-pressure mercury arc. The two models are based on the resolution of bidimensional time-dependent equations by a semi-implicit finite-element code. The numerical computation of turbulent model is solved with large eddy simulation model; this approach takes into account the various scales of turbulence by a filtering method on each scale. The results show the quantitative influence of turbulence on the flow fields and also the difference between laminar and turbulent effects on the dynamic thermal behaviour and on the characteristics of the discharge.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Description of the LASSO Alpha 1 Release

The Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility began a pilot project in May 2015 to design a routine, high-resolution modeling capability to complement ARM’s extensive suite of measurements. This modeling capability has been named the Large-Eddy Simulation (LES) ARM Symbiotic Simulation and Observation (LASSO) project. The availability of LES simulations with concurrent observations will serve many purposes. LES helps bridge the scale gap between DOE ARM observations and models, and the use of routine LES adds value to observations. It provides a self-consistent representation of the atmosphere and a dynamical context for the observations. Further, it elucidates unobservable processes and properties. LASSO will generate a simulation library for researchers that enables statistical approaches beyond a single-case mentality. It will also provide tools necessary for modelers to reproduce the LES and conduct their own sensitivity experiments. Many different uses are envisioned for the combined LASSO LES and observational library. For an observationalist, LASSO can help inform instrument remote-sensing retrievals, conduct Observation System Simulation Experiments (OSSEs), and test implications of radar scan strategies or flight paths. For a theoretician, LASSO will help calculate estimates of fluxes and co-variability of values, and test relationships without having to run the model yourself. For a modeler, LASSO will help one know ahead of time which days have good forcing, have co-registered observations at high-resolution scales, and have simulation inputs and corresponding outputs to test parameterizations. Further details on the overall LASSO project are available at http://www.arm. gov/science/themes/lasso.

54 ENVIRONMENTAL SCIENCES↗

Numerical Simulation of Slag Eye Formation and Slag Entrapment in a Bottom-Blown Argon-Stirred Ladle

A transient mathematical model is developed for simulating the bubble-steel-slag-top gas four-phase flow in a bottom-blown argon-stirred ladle with a 70-ton capacity. The Lagrangian discrete phase model (DPM) is used for describing the moving behavior of bubbles in the steel and slag. To observe the formation process of slag eye, the volume of fluid (VOF) model is used to track the interfaces between three incompressible phases: metal/slag, metal/gas, and slag/gas. The complex multiphase turbulent flow induced by bubble-liquid interactions is solved by a large eddy simulation (LES) model. Slag eye area and slag droplet dispersion are investigated under different gas flow rates. The results show that the movement of bubbles, formation and collapse of slag eye, volatility of steel/slag interface and behavior of slag entrapment can be properly predicted in the current model. When the gas flow rate is 300 L/min, the circulation driven by the bubble plume will stir the entire ladle adequately and form a slag eye of the right size. At the same time, it will not cause strong erosion to the ladle wall, and the fluctuation of the interface is of adequate intensity, which will be helpful for improving the desulfurization efficiency; the slag entrapment behavior can also be decreased. Interestingly, with the motion of liquid steel circulation, the collision and coalescence of dispersed slag droplets occur during the floating process in the vicinity of the wall.

36 MATERIALS SCIENCE↗

Characterizing the Turbulent Structure of the Convective Boundary Layer Using ARM/ASR Observations and LES Model Output

This project used high-resolution observations and output from large-eddy simulation models to characterize turbulent motions within the planetary boundary layer. As part of this research, we (a) continued development of techniques to derive profiles of temperature and humidity from ground-based instruments, (b) characterized the higher order moments of water vapor at a tropical location, (c) evaluated the time-of-day dependent turbulent mixing within the boundary layer, (d) developed an improved method to derive turbulent quantities at the top of the boundary layer from profiles of temperature, humidity, and wind, (e) organized and conducted a large field campaign to study the interactions between the land surface and atmosphere, and (f) developed improved ways to determine the depth of the boundary layer.

54 ENVIRONMENTAL SCIENCES↗

Evolution equations for the joint probability of several compositions in turbulent combustion

One-point statistical simulations of turbulent combustion require models to represent the molecular mixing of species mass fractions, which then determine the reaction rates. For multi-species mixing the Dirichlet distribution has been used to characterize the assumed joint probability density function (PDF) of several scalars, parametrized by solving modeled evolution equations for their means and the sum of their variances. The PDF is then used to represent the mixing state and to obtain the chemical reactions source terms in moment closures or large eddy simulation. We extend the Dirichlet PDF approach to transported PDF methods by developing its governing stochastic differential equation (SDE). The transport equation, as opposed to parametrizing the assumed PDF, enables (1) the direct numerical computation of the joint PDF (and therefore the mixing model to directly account for the flow dynamics (e.g. reaction) on the shape of the evolving PDF), and (2) the individual specification of the mixing timescales of each species. From the SDE, systems of equations are derived that govern the first two moments, based on which constraints are established that provide consistency conditions for material mixing. A SDE whose solution is the generalized Dirichlet PDF is also developed and some of its properties from the viewpoint of material mixing are investigated. The generalized Dirichlet distribution has the following advantages over the standard Dirichlet distribution due to its more general covariance structure: (1) its ability to represent differential diffusion (i.e. skewness) without affecting the scalar means, and (2) it can represent both negatively and positively correlated scalars. The resulting development is a useful representation of the joint PDF of inert or reactive scalars in turbulent flows: (1) In moment closures, the mixing physics can be consistently represented by one underlying modeling principle, the Dirichlet or the generalized Dirichlet PDF, and (2) based on the SDEs transported PDF mixing models for multi-species diffusion can be constructed by specifying the SDE coefficients.

97 MATHEMATICS AND COMPUTING↗

CFD simulations of electric motor end ring cooling for improved thermal management

Proper thermal management of an electric motor for vehicle applications extends its operating range. One cooling approach is to impinge Automatic Transmission Fluid (ATF) onto the rotor end ring. Increased ATF coverage correlates to enhanced heat transfer. Computational Fluid Dynamics (CFD) analytical tools provide a mechanism to assess motor thermal management prior to hardware fabrication. The complexity of the fluid flow (e.g., jet atomization, interface tracking, wall impingement) and heat transfer makes these simulations challenging. Computational costs are high when solving these flows on high-speed rotating meshes. Typically, a Volume-of Fluid (VOF) technique (i.e., two-fluid system) is used to resolve ATF dynamics within this rotating framework. Suitable numerical resolution of the relevant physics for thin films under strong inertial forces at high rotor speeds is computationally expensive, further increasing the run times. In this work, a numerical study of rotor-ring cooling by ATF is presented using a patent automated Cartesian cut-cell based method coupled with Automatic Mesh Refinement (AMR). This approach automatically creates the Cartesian mesh on-the-fly and can effectively handle complex rotating geometries by adaptively refining the mesh based on local gradients in the flow field which results in better resolution of the air-ATF interface. A Single non-inertial Reference Frame (SRF) approach is used to account for the rotating geometry and to further improve the overall computational efficiency. Quasi-steady state conditions are targeted in the analysis of the results. Important physics such as ATF jet structure, velocity detail near the air-jet interface, ATF coverage/accumulation on the ring surface, and cooling capacity are presented for a low-resolution Reynolds averaged Navier-Stokes (RANS), high-resolution RANS, and high-resolution Large-Eddy Simulation (LES) models. Computations are scaled over hundreds of cores on a supercomputer to maximize turnaround time. Each numerical approach is shown to capture the general trajectory of the oil jet prior to surface impingement. The high-resolution LES simulation, however, is superior in capturing small scale details and heat transfer between the free jet and surrounding air.

42 ENGINEERING↗

The origin of water vapor rings in tropical oceanic cold pools

Tropical deep convection over the ocean is found to grow preferentially from thermodynamically preconditioned regions of high specific humidity and, thus, high moist static energy. Because of this, rings of enhanced specific humidity at the leading edges of evaporatively driven cold pools have recently received considerable attention. The prevailing theory explains these rings by the water vapor source from the evaporation of rain drops below cloud base. Their origin is reported on in this letter using large-eddy simulations of individual cumulus clouds that rise into a tropical atmosphere over ocean. It is demonstrated that - in contrast to this theory - water vapor rings are primarily explained by surface latent heat fluxes rather than by the evaporation of rain. This result implies that conceptual models used in subgrid-scale parameterizations of deep convection should consider the formation of rings of increased specific humidity by the cold-pool-induced enhancement of surface fluxes.

54 ENVIRONMENTAL SCIENCES↗

On the Influence of Swell Propagation Angle on Surface Drag

Abstract A combination of turbulence-resolving large-eddy simulations and observations are used to examine the influence of swell amplitude and swell propagation angle on surface drag. Based on the analysis a new surface roughness parameterization with nonequilibrium wave effects is proposed. The surface roughness accounts for swell amplitude and wavelength and its relative motion with respect to the mean wind direction. The proposed parameterization is tested in uncoupled three-dimensional Weather and Research Forecasting (WRF) simulations at grid sizes near 1 km where we explore potential implications of our modifications for two-way coupled atmosphere–wave models. Wind–wave misalignment likely explains the large scatter in observed nondimensional surface roughness under swell-dominated conditions. Andreas et al.’s relationship between friction velocity and the 10-m wind speed under predicts the increased drag produced by misaligned winds and waves. Incorporating wave-state (speed and direction) influences in parameterizations improves predictive skill. In a broad sense, these results suggest that one needs information on winds and wave state to upscale buoy measurements.

54 ENVIRONMENTAL SCIENCES↗

A Study of Strain Rate Effects for Turbulent Premixed Flames with Application to LES of a Gas Turbine Combustor Model

Large-scale strain rate field, a resolved quantity which is easily computable in large-eddy simulations (LES), could have profound effects on the premixed flame properties by altering the turbulent flame speed and inducing local extinction. The role of the resolved strain rate has been investigated in a posterior LES study of GE lean premixed dry low NOx emissions LM6000 gas turbine combustor model. A novel approach which is based on the coupling of the lineareddy model with a one-dimensional counter-flow solver has been applied to obtain the parameterizations of the resolved premixed flame properties in terms of the reactive progress variable, the local strain rate measure, and local Reynolds and Karlovitz numbers. The strain rate effects have been analyzed by comparing LES statistics for several models of the turbulent flame speed, i.e, with and without accounting for the local strain rate effects, with available experimental data. The sensitivity of the simulation results to the inflow velocity conditions as well as the grid resolution have been also studied. Overall, the results suggest the necessity to represent the strain rate effects accurately in order to improve LES modeling of the turbulent flame speed.

33 ADVANCED PROPULSION SYSTEMS↗

Wall-modeled LES of Flow Over a Gaussian Bump

We perform wall-modeled large eddy simulations (WMLES) of turbulent flow over a Gaussian-shaped bump geometry, to assess its performance in the accelerating and separation regions of the flow. The flow conditions are based on the ongoing CFD validation experiments of Slotnick [NATO STO-MP-AVT-307, 2019]. The oncoming flow Mach number is 0.176, and two Reynolds numbers are simulated that are about 10000 and 36000 based on boundary layer thickness upstream of the bump. Preliminary Reynolds-averaged Navier-Stokes simulations are first performed to assess the effects of Mach number, Reynolds number, tunnel top and sidewall effects. Finally, WMLES results with an equilibrium wall model will be presented at two Reynolds numbers to assess their performance for this flow by making detailed comparisons with available experimental and higher-fidelity numerical data.

turbulence, wall model, large eddy simulation↗

High-resolution calculations of the solar global convection with the reduced speed of sound technique. I. The structure of the convection and the magnetic field without the rotation

We carry out non-rotating high-resolution calculations of the solar global convection, which resolve convective scales of less than 10 Mm. To cope with the low Mach number conditions in the lower convection zone, we use the reduced speed of sound technique (RSST), which is simple to implement and requires only local communication in the parallel computation. In addition, the RSST allows us to expand the computational domain upward to about 0.99 R {sub ☉}, as it can also handle compressible flows. Using this approach, we study the solar convection zone on the global scale, including small-scale near-surface convection. In particular, we investigate the influence of the top boundary condition on the convective structure throughout the convection zone as well as on small-scale dynamo action. Our main conclusions are as follows. (1) The small-scale downflows generated in the near-surface layer penetrate into deeper layers to some extent and excite small-scale turbulence in the region >0.9 R {sub ☉}, where R {sub ☉} is the solar radius. (2) In the deeper convection zone (<0.9 R {sub ☉}), the convection is not influenced by the location of the upper boundary. (3) Using a large eddy simulation approach, we can achieve small-scale dynamo action and maintain a field of about 0.15B {sub eq}-0.25B {sub eq} throughout the convection zone, where B {sub eq} is the equipartition magnetic field to the kinetic energy. (4) The overall dynamo efficiency varies significantly in the convection zone as a consequence of the downward directed Poynting flux and the depth variation of the intrinsic convective scales.

79 ASTRONOMY AND ASTROPHYSICS↗