Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Effect of the addition of Si into V 2 O 5 coatings: Structure and tribo-mechanical properties

Vanadium oxide (V2O5) is one of the lubricious oxides with the potential to be used as a solid lubricant at elevated temperatures. However, the material itself is not hard wear-resistant, so most of the research has focused on adding V into hard nitride coatings that could lead to the formation of a self-lubricating V(2)O(5)layer when heated. The other possible solution, which has been less studied, is to look for mechanisms to enhance the hardness of the oxide coating. In this research, we investigate the effect of the addition of Si into the V2O5 coatings, aiming to find conditions that lead to enhance hardness and/or reduced wear while keeping the high temperature lubricity of the V2O5 structure. For this, Si modified V2O5 coatings were deposited using a dual magnetron sputtering system. The results showed that small additions of Si (< 2.0 at%) improved the hardness of the V2O5 coatings up to 5 times while keeping the same temperature dependence of the coefficient of friction than V2O5. Dry sliding experiments using the pin-on-disc configuration against silicon nitride balls were performed at 25, 300 and 600 degrees C. Wear factors in the 10(-7) mm(3)/Nm range were obtained, indicating a good wear resistance. Further addition of Si into the V2O5 structure led to a loss of the crystalline ordering and a significant reduction in the hardness.

Hall-Petch↗

Correlating high temperature mechanical and tribological properties of CrAlN and CrAlSiN hard coatings

CrAlN and CrAlSiN hard coatings deposited by magnetron sputtering were analyzed for their high temperature mechanical and tribological properties. High temperature nanoindentation measurements on both coatings were performed from room temperature up to 700 °C in steps of 100 °C where a reduction in hardness H and elastic modulus E* from their initial values was noticed. In addition, high temperature tribological tests were conducted in inert atmosphere in the same temperature range to obtain information about the coefficient of friction and the wear coefficient. In order to link the tribological behavior to the obtained mechanical properties, the H/E* ratio was calculated and compared to the high temperature wear from the current and other studies with similar coatings. Finally, the evolution of the mechanical and tribological properties at high temperature is discussed based on the current knowledge available in literature.

Drnovšek, Aljaž↗

High temperature fracture toughness of single-layer CrAlN and CrAlSiN hard coatings

Hardness and toughness are among of the most important physical properties of hard coatings and it is important to analyze them at temperatures present during coating applications. CrAlN and CrAlSiN are hard coating materials frequently used in high temperature applications. Here, while both possess high oxidation resistance and thermal stability, they differ in their microstructure. In this work, the fracture toughness of magnetron-sputtered single-layer CrAlN and CrAlSiN hard coatings was determined up to 700 °C by in-situ scanning electron microscopy micro-cantilever deflection tests. The results show a decreasing trend of the fracture toughness with increasing temperature. While both coatings' fracture toughness trends are similar up to 400 °C, they diverge at higher temperatures. In general, the evolution of the fracture toughness with increasing temperature shows similarities to the observed changes in hardness in the same temperature range.

36 MATERIALS SCIENCE↗

Adhesion, structure, and mechanical properties of Cr HiPIMS and cathodic arc deposited coatings on SiC

Chromium deposited by high-power impulse magnetron sputtering (HIPIMS) versus cathodic arc (CA) processes exhibits very different mechanical properties. Combining the two can result in a single-phase with superior performance that can be tailored for use in coating SiC for advanced nuclear fuel cladding. Coating morphology, residual stress, elemental depth profiles, and mechanical testing by scratch, pull-off adhesion, and microcantilevers are shown for HiPIMS, CA, and combined coatings. CA coatings were likely to spall and had lower adhesion strength due to tensile residual stresses but had desirable material properties. Additionally, by depositing an initial layer of Cr by HiPIMS followed by a layer of Cr by CA, a more adherent coating was achieved and some of the stress issues with CA morphology were resolved. Combined coatings withstood at least 80 MPa in pull-off adhesion tests and had maximum failure stress values of 5GPa in microcantilever tests. These results were better than either individual deposition method and point to a hybrid approach being a path forward for a more robust coating.

36 MATERIALS SCIENCE↗

Modes of strain accommodation in Cu-Nb multilayered thin film on indentation and cyclic shear

Two-phase layered thin films with a high density of semi-coherent interfaces exhibit excellent mechanical properties and thermal stability. Here, in this study, a magnetron-sputtered Cu-Nb dual-layered thin film (~500 nm for Cu and ~150 nm for Nb) having an amorphous interface between Cu and Nb with a high density of aligned growth twins in Cu is subjected to severe surface deformation. The material is loaded using indentation and cyclic shear under tribological testing. The strain accommodation in the subsurface microstructure after deformation varies based on the local structure and deformation mode. Grain refinement and crack formations in the stressed region of the Nb layer and localized crystallization of the amorphous interface are observed after indentation and scratch testing. Pronounced detwinning of growth twins in the Cu layer under the cyclic shear strain leaves large dislocations sites and loops which are observed both by high-resolution transmission electron microscopy and experiment-guided molecular dynamic (MD) simulations. Our simulations provided insights into understanding the pathway for the detwinning process under cyclic shear loading.

36 MATERIALS SCIENCE↗

Residual stress characterization of Al/SiC nanoscale multilayers using X-ray

Nanolayered composites are used in a variety of applications such as wear resistant coatings, thermal barrier coatings, optical and magnetic thin films, and biological coatings. Residual stresses produced in these materials during processing play an important role in controlling their microstructure and properties. In this paper, we have studied the residual stresses in model metal-ceramic Al/SiC nanoscale multilayers produced by physical vapor deposition (magnetron sputtering). X-ray synchrotron radiation was used to measure stresses in the multilayers using the sin{sup 2} {Psi} technique. The stresses were evaluated as a function of layer thicknesses of Al and SiC and also as a function of the number of layers. The stress state of Al in the multilayer was largely compressive, compared to single layer Al stresses. This is attributed to a peening mechanism due to bombardment of the Al layers by SiC and Ar neutrals during deposition. The stress evolution was numerically modeled by a simplified peening process to qualitatively explain the Al thickness-dependent residual stresses.

36 MATERIALS SCIENCE↗

Surface studies of crystalline and amorphous Zn-In-Sn-O transparent conducting oxides

X-ray and ultraviolet photoelectron spectroscopy (UPS) studies were made of in situ RF magnetron-sputtered crystalline (c) and amorphous (a) Zn–In–Sn–O (ZITO) thin films, ex situ pulsed laser deposited c- and a-ZITO thin films, and bulk ZITO ceramics. Cosubstitution of Zn and Sn for In results in an increase of the In core level binding energy at a given Fermi level compared to that measured in undoped and Sn-doped In 2 O 3 (ITO). In plots of work function vs. Fermi level, in situ c-ZITO and a-ZITO films have low ionization potentials (7.0–7.7 eV) that are similar to undoped In 2 O 3 . In contrast, dry-air-annealed in situ films, ex situ films, and bulk ceramics have higher ionization potentials (7.7–8.1 eV) that are more similar to ITO and match well with previous work on air-exposed surfaces. Kelvin Probe measurements were made of select a-ZITO films exposed to air and ultraviolet/ozone-treated so as to measure work functions under conditions commonly employed for device fabrication. Results (4.8–5.3 eV) were in good agreement with the UPS work functions of oxygen-exposed materials and with literature values. Lastly, a parallelogram plot of work function vs. Fermi level shows that a wider range of work functions is achievable in ZITO materials as compared to other transparent conducting oxides (Sb-doped SnO 2 , Al-doped ZnO, Sn-doped In 2 O 3 ), making ZITO more versatile for applications.

Proffit, Diana E↗

Influence of hydrostatic pressure on superconducting properties of niobium thin film

We have studied superconducting properties of niobium thin films under hydrostatic pressures up to 3 GPa. The films with thickness of 100 nm were prepared in the high vacuum DC magnetron sputtering system (with critical temperature TC = 8.95 K at ambient pressure). The produced high quality films have been characterized using electrical resistivity and magnetization measurements, X-ray diffraction, and atomic force microscope imaging. We have observed increase of TC with increasing value of applied pressure (dTC/dp = 73 mK/GPa) up to 3 GPa. This observation is different to pressure effect observed on bulk sample of Nb. In this paper we are discussing the origin of this discrepancy. (C) 2014 Elsevier B.V. All rights reserved.

Pristáš, Gabriel↗

Reactive multilayers fabricated by vapor deposition. A critical review

The reactive multilayer thin films are a class of energetic materials that continue to attract attention for use in joining applications and as igniters. Generally composed of two reactants, these heterogeneous solids can be stimulated by an external source to promptly release stored chemical energy in a sudden emission of light and heat. In our critical review article, results from recent investigations of these materials are discussed. Discussion begins with a brief description of the vapor deposition techniques that provide accurate control of layer thickness and film composition. More than 50 reactive film compositions have been reported to date, with most multilayers fabricated by magnetron sputter deposition or electron-beam evaporation. In later sections, we review how multilayer ignition threshold, reaction rate, and total heat are tailored via thin film design. For example, planar multilayers with nanometer-scale periodicity exhibit rapid, self-sustained reactions with wavefront velocities up to 100 m/s. Numeric and analytical models have elucidated many of the fundamental processes that underlie propagating exothermic reactions while demonstrating how reaction rates vary with multilayer design. Recent, time-resolved diffraction and imaging studies have further revealed the phase transformations and the wavefront dynamics associated with propagating chemical reactions. Many reactive multilayers (e.g., Co/Al) form product phases that are consistent with published equilibrium phase diagrams, yet a few systems, such as Pt/Al, develop metastable products. The final section highlights current and emerging applications of reactive multilayers. Examples include reactive Ni(V)/Al and Pd/Al multilayers which have been developed for localized soldering of heat-sensitive components.

36 MATERIALS SCIENCE↗

Indium doped Cd1-xZnxO alloys as wide window transparent conductors

We have synthesized Indium doped Cd 1-x Zn x O alloys across the full composition range using magnetron sputtering method. The crystallographic structure of these alloys changes from rocksalt (RS) to wurtzite (WZ) when the Zn content is higher than 30%. The rocksalt phase alloys in the composition range 0 < x < 0.3 can be efficiently n-type doped, shifting the absorption edge to 3.25 eV and reducing resistivity to about 2.0 × 10 -4 Ω-cm. Here, we found that In doped CdO (ICO) transmits more solar photons than commercial fluorine doped tin oxide (FTO) with comparable sheet conductivity. The infrared transmittance is further extended to longer than 1500 nm wavelengths by depositing the In doped Cd 1-x Zn x O in ~ 1% of O 2 . This material has a potential for applications as a transparent conductor for silicon and multi-junction solar cells.

36 MATERIALS SCIENCE↗

Tribological performance of quaternary CrSiCN coatings under dry and lubricated conditions

This paper presents an experimental study of friction and wear performance of quaternary CrSiCN coatings deposited on a hardened H-13 steel substrate by a plasma enhanced magnetron sputtering (PEMS) technique. Friction and wear tests were conducted with a reciprocating line contact between a hardened 4370 steel roller and coated and uncoated flat specimens under dry and lubricated conditions. The effects of coating thickness (1, 3.5 and 7.5 μm) on the mechanical properties, friction and wear performance were also assessed. In dry sliding, the friction of coated surfaces was about the same as for uncoated surfaces, except for the 1-μm coating, which had higher friction. Friction for coated surfaces under lubricated contact was in general higher than for uncoated surfaces. There was no measurable wear on any of the coated surfaces, under either dry or lubricated conditions. However, wear was higher on the steel roller counterface sliding against the coated surfaces, with the amount of wear proportional to the mating coating thickness. The effectiveness of formulated lubricant additives was also modified by the coating, resulting in major effects on friction and wear behavior. Finally, this reduction in lubricant additive efficacy is due to the fact that the additives were designed and optimized for ferrous surfaces.

36 MATERIALS SCIENCE↗

A Transmission Electron Microscopy Study of the Effect of Interfaces on Bubble Formation in He-Implanted Cu-Nb Multilayers

Magnetron sputtered thin films of Cu, Nb, and Cu-Nb multilayers with 2.5 and 5 nm nominal layer thickness were deposited on Si and implanted with 4He+ and 3He+ ions. Secondary ion mass spectroscopy and nuclear reaction analysis, respectively, were used to measure the 4He+ and 3He+ concentration profile with depth inside the films. Cross-sectional transmission electron microscopy was used to characterize the helium bubbles. Analysis of the contrast from helium bubbles in defocused transmission electron microscope images showed a minimum bubble diameter of 1.25 nm. While pure Cu and Nb films showed bubble contrast over the entire range of helium implantation, the multilayers exhibited bubbles only above a critical He concentration that increased almost linearly with decreasing layer thickness. The work shows that large amounts of helium can be trapped at incoherent interfaces in the form of stable, nanometer-size bubbles.

36 MATERIALS SCIENCE↗

Effect of Gold Catalyst Surface Morphology on Wetting Behavior and Electrochemical CO 2 Reduction Performance in a Large-Area Zero-Gap Gas Diffusion Electrolyzer

We report catalyst surface area and wetting behavior are key factors in determining the performance of gas diffusion electrode (GDE) electrolyzers for electrochemical CO 2 reduction. In this work, we report the integration of sub-1 μm thick nanoporous gold (npAu) catalyst coatings into a large-area (25 cm 2 ) zero-gap electrolyzer. The npAu coatings were prepared by magnetron sputtering (MS) of thin AgAu alloy films on the microporous carbon layer of a gas diffusion layer (GDL) followed by Ag leaching. Compared to MS Au films of the same thickness, npAu catalyst coatings enable higher Faradaic efficiencies and improved catalyst stability for CO 2 -to-CO reduction with Faradaic efficiencies of up to 88% at 100 mA/cm 2 . For a 800 nm npAu coating, the device level energy efficiency for CO 2 to CO conversion reaches 45% (52% for CO + H 2 ) at 100 mA/cm 2 with a single pass CO 2 conversion efficiency of ~12%. Contact angle measurements reveal that npAu coatings provide a more hydrophobic electrode interface compared to MS Au coatings, suggesting that the more hydrophobic interfacial environment of npAu coatings helps mitigating electrode flooding which is associated with performance deterioration over time.

30 DIRECT ENERGY CONVERSION↗

Electrochromic Properties of Perovskite NdNiO 3 Thin Films for Smart Windows

Semiconductors with electrically tunable band gaps are of great interest in controlling transparency to electromagnetic radiation. Thin films of perovskite nickelate NdNiO 3 (NNO), a class of correlated oxides, were deposited on single-crystal (LaAlO 3 (LAO)) and polycrystalline (fluorine-doped tin oxide-coated glass (FTO)) substrates by magnetron sputtering, chemical solution deposition (CSD), and atomic layer deposition (ALD). Their electrochromic behaviors were investigated using a three-electrode setup in basic (KOH solution, pH = 12) electrolyte. During bleaching/coloration process, the proton intercalation/deintercalation and simultaneous electron compensation in the NNO lattice under electrical bias led to crossover of the material between the pristine-conducting phase (Ni 3+ ) and the strongly correlated insulating phase (Ni 2+ ), which serves as the working principle for electrochromic (tunable opacity in the visible range) behavior. Cyclic voltammetry (CV) scans demonstrate that NNO films are electrochemically stable in basic solutions for all three film deposition methods explored here. CV scans at varying rates enabled the extraction of diffusion coefficient of protons in thin film NNO, which is similar to 10 –7 cm 2 s –1 among all films studied. Large light transmittance modulation by bleaching and coloration was observed on films grown on both LAO and FTO substrates, suggesting its potential as an electrochromic material candidate for smart windows and optical shutter applications. Here, porous NNO films obtained by chemical solution deposition tend to demonstrate stronger electrochromic activity than dense films grown by sputtering or ALD.

36 MATERIALS SCIENCE↗

Scalable Gas Diffusion Electrode Fabrication for Electrochemical CO 2 Reduction Using Physical Vapor Deposition Methods

Electrochemical CO 2 reduction (ECR) promises the replacement of fossil fuels as the source of feedstock chemicals and seasonal storage of renewable energy. While much progress has been made in catalyst development and electrochemical reactor design, few studies have addressed the effect of catalyst integration on device performance. Using a microfluidic gas diffusion electrolyzer, we systematically studied the effect of thickness and the morphology of electron beam (EB) and magnetron-sputtered (MS) Cu catalyst coatings on ECR performance. We observed that EB-Cu outperforms MS-Cu in current density, selectivity, and energy efficiency, with 400 nm thick catalyst coatings performing the best. Additionally, the superior performance of EB-Cu catalysts is assigned to their faceted surface morphology and sharper Cu/gas diffusion layer interface, which increases their hydrophobicity. Tests in a large-scale zero-gap electrolyzer yielded similar product selectivity distributions with an ethylene Faradaic efficiency of 39% at 200 mA/cm 2 , demonstrating the scalability for industrial ECR applications.

36 MATERIALS SCIENCE↗

Mechanical Properties and Chemical Reactivity of Li x SiO y Thin Films

Silicon (Si) is a commonly studied candidate material for next-generation anodes in Li-ion batteries. A native oxide SiO 2 on Si is often inevitable. However, it is not clear if this layer has a positive or negative effect on the battery performance. This understanding is complicated by the lack of knowledge about the physical properties of the SiO 2 lithiation products and by the convolution of chemical and electrochemical effects during the anode lithiation process. In this study, Li x SiO y thin films as model materials for lithiated SiO 2 were deposited by magnetron sputtering at ambient temperature, with the goal of (1) decoupling chemical reactivity from electrochemical reactivity and (2) evaluating the physical and electrochemical properties of Li x SiO y . X-ray photoemission spectroscopy analysis of the deposited thin films demonstrate that a composition close to previous experimental reports of lithiated native SiO 2 can be achieved through sputtering. Our density functional theory calculations also confirm that the possible phases formed by lithiating SiO 2 are very close to the measured film compositions. Scanning probe microscopy measurements show that the mechanical properties of the film are strongly dependent on lithium concentration, with a ductile behavior at a higher Li content and a brittle behavior at a lower Li content. The chemical reactivity of the thin films was investigated by measuring the AC impedance evolution, suggesting that Li x SiO y continuously reacts with the electrolyte, in part because of the high electronic conductivity of the film determined from solid-state impedance measurements. The electrochemical cycling data of the sputter-deposited Li x SiO y /Si films also suggest that Li x SiO y is not beneficial in stabilizing the Si anode surface during battery operation, despite its favorable mechanical properties.

14 SOLAR ENERGY↗