SEARCH · Search NASA

Results for “Optimal sizing method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

All sources NASA NTRS DOE OSTI

DOE OSTI2016

SU-F-I-72: Evaluation of the Ancillary Lead Shielding for Optimizing Radiation Protection in the Interventional Radiology Department

Purpose: The rising complexity of interventional fluoroscopic procedures has resulted in an increase of occupational radiation exposures in the interventional radiology (IR) department. This study assessed the impact of ancillary shielding on optimizing radiation protection for the IR staff. Methods: Scattered radiation measurements were performed in two IR suites equipped with Axiom Artis systems (Siemens Healthcare, Erlangen, Germany) installed in 2006 and 2010. Both rooms had suspended ceiling-mounted lead-acrylic shields of 75×60 cm (Mavig, Munich, Germany) with lead equivalency of 0.5 mm, and under-table drapes of 70×116 cm and 65×70 cm in the newer and the older room respectively. The larger skirt can be wrapped around the table’s corner and in addition the newer suite had two upper shields of 25×55 cm and 25×35 cm. The patient was simulated by 30 cm of acrylic, air kerma rate (AKR) was measured with the 180cc ionization chamber (AccuPro Radcal Corporation, Monrovia, CA, USA) at different positions. The ancillary shields, x-ray tube, image detector, and table height were adjusted by the IR radiologist to simulate various clinical setups. The same exposure parameters were used for all acquisitions. AKR measurements were made at different positions relative to the operator. Results: The AKR measurements demonstrated 91–99% x-ray attenuation by the drapes in both suites. The smaller size of the under-table skirt and absence of the side-drapes in the older room resulted in a 20–50 fold increase of scattered radiation to the operator. The mobile suspended lead-acrylic shield reduced AKR by 90–94% measured at 150–170 cm height. The recommendations were made to replace the smaller under-table skirt and to use the ceiling-mounted shields for all IR procedures. Conclusion: The ancillary shielding may significantly affect radiation exposure to the IR staff. The use of suspended ceiling-mounted shields is especially important for reduction of interventional radiologists’ cranial radiation.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2022

GrainNN: A neighbor-aware long short-term memory network for predicting microstructure evolution during polycrystalline grain formation

High fidelity simulations of grain formation in alloys are an indispensable tool for process-to-mechanical-properties characterization. Such simulations, however, can be computationally expensive as they require fine spatial and temporal discretizations. Their cost becomes an obstacle to parametric studies and ensemble runs and ultimately makes downstream tasks like optimal control and uncertainty quantification challenging. To enable such downstream tasks, we introduce GrainNN, an efficient and accurate reduced-order model for epitaxial grain growth in additive manufacturing conditions. GrainNN is a sequence-to-sequence long-short-term-memory (LSTM) deep neural network that evolves the dynamics of manually crafted features. Its innovations are (1) an attention mechanism with grain-microstructure-specific transformer architecture; and (2) an overlapping combination of several clones of the network to generalize to grain configurations that are different from those used for training. This design enables GrainNN to predict grain formation for unseen physical parameters, grain number, domain size and geometry. Furthermore, GrainNN not only reconstructs the quantities of interest but also can be pointwise accurate. In our numerical experiments, we use a polycrystalline phase field method to both generate the training data and assess GrainNN. For multiparametric, ensemble simulations with many grains, GrainNN can be orders of magnitude faster than phase field simulations, while delivering 5%–15% pointwise error. Additionally, this speedup includes the cost of the phase field simulations for generating training data.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Automating Bayesian inference and design to quantify acoustic particle levitation

Self-propulsion of micro- and nanoparticles powered by ultrasound provides an attractive strategy for the remote manipulation of colloidal matter using biocompatible energy inputs. Quantitative understanding of particle motion and its dependence on size, shape, and composition requires accurate characterization of the acoustic field, which depends sensitively on the experimental setup. Here, we show how automated experiments based on Bayesian inference and design can accurately and efficiently characterize the acoustic field within resonant chambers used to propel acoustic nanomotors. Repeated cycles of observation, inference, and design (OID) are guided by a physical model that describes the rate at which levitating particles approach the nodal plane. Using video microscopy, we observe the relaxation of tracer particles to this plane following the application of the acoustic field. We use sequential Monte Carlo methods to infer model parameters such as the amplitude and frequency of the resonant chamber while accounting for particle-level measurement noise and population-level heterogeneity in the field. Guided by simulated outcomes, we select the optimal design for the next experiment as to maximize the information gain in the relevant parameters. We show how this iterative process serves to discriminate between competing hypotheses and efficiently converges to accurate parameter estimates using only few automated experiments. We discuss the need for model criticism to ensure the validity of the guiding model throughout automated cycles of observation, inference, and design. Furthermore, this work demonstrates how Bayesian methods can learn the parameters of nonlinear, hierarchical models used to describe video microscopy data of active colloids.

42 ENGINEERING↗

DOE OSTI2016

SU-G-JeP4-09: Impact of Interfractional Motion On Hypofractionated Pencil Beam Scanning Proton Therapy for Prostate Cancer

Purpose: To investigate the impact of anatomy/setup variations on standard vs. hypofractionated anterolateral pencil beam scanning (PBS) proton therapy for prostate cancer. Methods: Six prostate cancer patients treated with double-scattering proton therapy, who underwent weekly verification CT scans were selected. Implanted fiducials were used for localization, and endorectal balloons for immobilization. New PBS plans using combination of lateral and anterior-oblique (AO) (±35 deg) beams were created. AO beams were added to spare the femoral heads during hypofractionation. Lateral beams delivered 50.4 Gy(RBE) to prostate plus 5-15mm of seminal vesicles and AO beams 28.8 Gy(RBE) to prostate, in 44 fractions. PTV was laterally expanded by 2.5% to account for range uncertainty. No range margins were applied for AO beams, assuming delivery with in-vivo range verification. Field-specific apertures with 1.2cm margin were used. Spot size was ∼9.5mm sigma for 172MeV @isocenter in air. Plans were optimized as single-field-uniform-dose with ∼5% maximum non-uniformity. The planned dose was recomputed on each weekly CT after aligning the fiducials with the simulation CT, scaled and accumulated via deformable image registration. Hypofractionated treatments with 12 and 5 fractions were considered. Equivalent doses were calculated for prostate (α/β= 1.5Gy), bladder and rectum (α/β= 3Gy). Results: The biological equivalent prostate dose was 86.2 and 92.9 Gyeq for the hypofractionation scenarios at 4.32 and 7.35 Gy/fx, respectively. The equivalent prostate D98 was degraded by on average 2.7 Gyeq for standard, and 3.1 and 4.0 Gyeq for the hypofractionated plans after accumulation. Differences between accumulated and planned Dmean/D2/EUD were generally reduced when reducing the number of fractions for bladder and rectum. The average Dmean/D2/EUD differences over all patients and organs-at-risk were 0.74/4.0/9.23, 0.49/3.64/5.51, 0.37/3.21/3.49 Gyeq for 44, 12 and 5 fractions. Conclusion: Hypofractionation makes proton therapy of prostate more susceptible to interfractional motion-induced target dose degradation compared to the standard fractionation.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2020

Multitask Recommender Systems for Cancer Drug Response

The problem we are currently trying to address is that there are many types of cancer drugs and many types of cancers and there is not always experimental data for a specific cancer type and cancer drug interaction. While there is a large possible set of feasible drug and cancer combinations, testing each pair is not realistic due to the high monetary cost of cell-based assays. Thus, this leaves researchers with a difficult choice of what drugs they should test on specific cancer types. This issue is known as the cold-start problem. Our focus is on developing recommender systems capable of addressing the cold-start problem as it relates to interaction between cancer types and cancer drugs. One of the most effective ways to address the cold-start problem is through large data analysis, however due to the cost prohibitive nature of cancer research the largest available data set size is the Genomics of Drug Sensitivity in Cancer with 494,973 genomic associations. To achieve optimal model performance on the cold-start problem, it is advantageous to employ multitask algorithms that are capable of transferring information between cancer datasets. The aim of this report is to draw from adaptations and state of the art developments in both algorithms for recommender systems and multitask learning to model the interaction between cancer cell lines and cancer drugs. Cancer cell lines are defined by the US National Cancer Institute as "cancer cells that keep dividing and growing over time, under certain conditions in a laboratory". This paper will focus on evaluating the performance of Neural Collaborative Filtering and Gaussian Processes, as well as their multitask adaptations, on cancer datasets from CCLE, NCI60, GDSC and CTRP. These methods will be evaluated on model performance in regression prediction but also in interpretability.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2020

Design optimization of semiconductor piezoresistors with Schottky diode contacts

A modeling theory is developed to predict the performance of piezoresistors which incorporate Schottky diode electrical contacts. This new theory allows the design of high performance gauges which can be fabricated using NonLithographically-Based Microfabrication (NLBM) techniques. These semiconductor piezoresistors can be designed in customizable sizes and fabricated in parallel in order to integrate position sensing into MEMS flexural positioners. Customizable nanopositioning platforms will enable advances in a range of nano-scale fabrication and metrology applications. A semiconductor piezoresistor with Schottky diode contacts was fabricated and attached to a titanium flexure. This device is shown to match predicted electrical performance within about 8% and to show a gauge factor of 116, within 2% of the predicted value. Performance limits for Schottky diode semiconductor piezoresistors are identified to be about 127dB full noise dynamic range for a quarter bridge over a 10kHz sensor bandwidth on a 600µm width titanium flexure, making them ideal for sensing on meso-/micro-scale flexural positioners. Methods of reaching these performance bound are suggested and their impact on the sensor dynamic range are studied.

42 ENGINEERING↗

DOE OSTI2015

A method to evaluate hydraulic fracture using proppant detection

Accurate determination of the proppant placement and propped fracture height are important for evaluating and optimizing stimulation strategies. A technology using non-radioactive proppant and a pulsed neutron gamma energy spectra logging tool to determine the placement and height of propped fractures is proposed in this paper. Gd 2 O 3 was incorporated into ceramic proppant and a Monte Carlo method was utilized to build the logging tools and formation models. Characteristic responses of the recorded information of different logging tools to fracture widths, proppant concentrations and influencing factors were studied. The results show that Gd capture gamma rays can be used to evaluate propped fractures and it has higher sensitivity to the change of fracture width and traceable proppant content compared with the exiting non-radioactive proppant evaluation techniques and only an after-fracture measurement is needed for the new method; The changes in gas saturation and borehole size have a great impact on determining propped fractures when compensated neutron and pulsed neutron capture tool are used. Finally, a field example is presented to validate the application of the new technique.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Efficacy of the radial pair potential approximation for molecular dynamics simulations of dense plasmas

Macroscopic simulations of dense plasmas rely on detailed microscopic information that can be computationally expensive and is difficult to verify experimentally. In this work, we delineate the accuracy boundary between microscale simulation methods by comparing Kohn–Sham density functional theory molecular dynamics (KS-MD) and radial pair potential molecular dynamics (RPP-MD) for a range of elements, temperature, and density. By extracting the optimal RPP from KS-MD data using force matching, we constrain its functional form and dismiss classes of potentials that assume a constant power law for small interparticle distances. Our results show excellent agreement between RPP-MD and KS-MD for multiple metrics of accuracy at temperatures of only a few electron volts. The use of RPPs offers orders of magnitude decrease in computational cost and indicates that three-body potentials are not required beyond temperatures of a few eV. Due to its efficiency, the validated RPP-MD provides an avenue for reducing errors due to finite-size effects that can be on the order of ∼20%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2018

Energy efficient spark plasma sintering: Breaking the threshold of large dimension tooling energy consumption

An energy efficient spark plasma sintering method enabling the densification of large size samples assisted by very low electric current levels is developed. In this method, the electric current is concentrated in the graphite foils around the sample. High-energy dissipation is then achieved in this area enabling the heating and full densification of large (alumina) parts (Ø 40 mm) at relatively low currents (800 A). The electrothermal mechanical simulation reveals that the electric current needed to heat the large samples is 70% lower in the energy efficient configuration compared to the traditional configuration. The presence of thermal and densification gradients is also revealed for the larger size samples. Potential solutions for this problem are discussed. The experiments confirm the possibility of full densification (96%-99%) of large alumina samples. This approach allows using small (and low cost) SPS devices (generally limited to 10-15 mm samples) for large-size samples (40-50 mm). Finally, the developed technique enables also an optimized energy consumption by large-scale SPS systems.

36 MATERIALS SCIENCE↗

DOE OSTI2016

SU-G-TeP3-14: Three-Dimensional Cluster Model in Inhomogeneous Dose Distribution

Purpose: We aim to investigate 3D cluster formation in inhomogeneous dose distribution to search for new models predicting radiation tissue damage and further leading to new optimization paradigm for radiotherapy planning. Methods: The aggregation of higher dose in the organ at risk (OAR) than a preset threshold was chosen as the cluster whose connectivity dictates the cluster structure. Upon the selection of the dose threshold, the fractional density defined as the fraction of voxels in the organ eligible to be part of the cluster was determined according to the dose volume histogram (DVH). A Monte Carlo method was implemented to establish a case pertinent to the corresponding DVH. Ones and zeros were randomly assigned to each OAR voxel with the sampling probability equal to the fractional density. Ten thousand samples were randomly generated to ensure a sufficient number of cluster sets. A recursive cluster searching algorithm was developed to analyze the cluster with various connectivity choices like 1-, 2-, and 3-connectivity. The mean size of the largest cluster (MSLC) from the Monte Carlo samples was taken to be a function of the fractional density. Various OARs from clinical plans were included in the study. Results: Intensive Monte Carlo study demonstrates the inverse relationship between the MSLC and the cluster connectivity as anticipated and the cluster size does not change with fractional density linearly regardless of the connectivity types. An initially-slow-increase to exponential growth transition of the MSLC from low to high density was observed. The cluster sizes were found to vary within a large range and are relatively independent of the OARs. Conclusion: The Monte Carlo study revealed that the cluster size could serve as a suitable index of the tissue damage (percolation cluster) and the clinical outcome of the same DVH might be potentially different.

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2026

Reference floating wind array designs for three representative regions

This work presents the systematic development of three open-source reference floating wind array designs. The designs are tailored to representative site conditions for three regions of the United States: Humboldt Bay off the coast of California, the Gulf of Maine, and the Gulf of America. We adopted existing reference designs for the individual 15 MW turbines, semisubmersible floating platforms, substations, mooring systems, and power cables – integrating and adapting them as needed for each location. We adapted existing dynamic cable designs to use larger conductor sizes to meet the arrays' power transmission requirements, and we set up redundant mooring systems for each substation. The layout of each array is a uniform-grid design optimized to approximately minimize the levelized cost of energy (LCOE) within a square lease area while satisfying spatial constraints. These constraints ensure adequate clearances between adjacent turbines and between underwater components during the layout optimization to prevent clashing and ensure that all components reside within the lease boundaries. Substations are included to allow accounting for intra-array cable costs. They are placed within the uniform grid to maintain the navigability of the arrays. For each feasible layout considered, annual energy production and cable routing costs are calculated and updated in the LCOE objective function. After the optimization, we refined the cable routing with a mix of algorithmic and manual methods to ensure that the cables avoid mooring system components and approach the substation with adequate clearances. We confirmed the suitability of each reference array's layout by comparing the wake losses at each wind heading angle to the wind rose, observing that the optimized layouts largely avoid wake losses in the predominant wind directions. These reference arrays provide open-source baseline designs to enable future research and innovation of floating wind technology at the array scale.

17 WIND ENERGY↗

DOE OSTI2019

Scaling and Quality of Modularity Optimization Methods for Graph Clustering

Real-world graphs exhibit structures known as “communities” or “clusters” consisting of a group of vertices with relatively high connectivity between them, as compared to the rest of the vertices in the network. Graph clustering or community detection is a fundamental graph operation used to analyze real-world graphs occurring in the areas of computational biology, cybersecurity, electrical grids, etc. Similar to other graph algorithms, owing to irregular memory accesses and inherently sequential nature, current algorithms for community detection are challenging to parallelize. However, in order to analyze large networks, it is important to develop scalable parallel implementations of graph clustering that are capable of exploiting the architectural features of modern supercomputers. In response to the 2019 Streaming Graph Challenge, we present quality and performance analysis of our distributed- memory community detection using Vite, which is our distributed memory implementation of the popular Louvain method, on the ALCF Theta supercomputer. Clustering methods such as Louvain that rely on modularity maximization are known to suffer from the resolution limit problem, preventing identification of clusters of certain sizes. Hence, we also include quality analysis of our shared-memory implementation of the Fast-tracking Resistance method, in comparison with Louvain on the challenge datasets. Furthermore, we introduce an edge-balanced graph distribution for our distributed memory implementation, that significantly reduces communication, offering up to 80% improvement in the overall execution time. In addition to performance/quality analysis, we also include details on the power/energy consumption, and memory traffic of the distributed-memory clustering implementation using real-world graphs with over a billion edges.

Ghosh, Sayan↗

DOE OSTI2024

Multivariate Machine Learning Models of Nanoscale Porosity from Ultrafast NMR Relaxometry

Abstract Nanoporous materials are of great interest in many applications, such as catalysis, separation, and energy storage. The performance of these materials is closely related to their pore sizes, which are inefficient to determine through the conventional measurement of gas adsorption isotherms. Nuclear magnetic resonance (NMR) relaxometry has emerged as a technique highly sensitive to porosity in such materials. Nonetheless, streamlined methods to estimate pore size from NMR relaxometry remain elusive. Previous attempts have been hindered by inverting a time domain signal to relaxation rate distribution, and dealing with resulting parameters that vary in number, location, and magnitude. Here we invoke well‐established machine learning techniques to directly correlate time domain signals to BET surface areas for a set of metal‐organic frameworks (MOFs) imbibed with solvent at varied concentrations. We employ this series of MOFs to establish a correlation between NMR signal and surface area via partial least squares (PLS), following screening with principal component analysis, and apply the PLS model to predict surface area of various nanoporous materials. This approach offers a high‐throughput, non‐destructive way to assess porosity in c.a. one minute. We anticipate this work will contribute to the development of new materials with optimized pore sizes for various applications.

Fricke, Sophia N.↗

DOE OSTI2024

Multivariate Machine Learning Models of Nanoscale Porosity from Ultrafast NMR Relaxometry

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Tuning successive linear programming to solve AC optimal power flow problem for large networks

Successive linear programming (SLP) is a practical approach for solving large-scale nonlinear optimization problems. Alternating current optimal power flow (ACOPF) is no exception, particularly the large size of real-world networks. However, in order to achieve tractability, it is essential to tune the SLP algorithm presented in the literature. This paper presents a modified SLP algorithm to solve the ACOPF problem, specified by the U.S. Department of Energy’s (DOE) Grid Optimization (GO) Competition Challenge 1, within strict time limits. The algorithm first finds a near-optimal solution for the relaxed problem (i.e., Stage 1). Then, it finds a feasible solution in the proximity of the near-optimal solution (i.e., Stage 2 and Stage 3). The numerical experiments on test cases ranging from 500-bus to 30,000-bus systems show that the algorithm is tractable. Here the results show that our proposed algorithm is tractable and can solve more than 80% of test cases faster than the well-known Interior Point Method while significantly reduce the number of iterations required to solve ACOPF. The number of iterations is considered an important factor in the examination of tractability which can drastically reduce the computational time required within each iteration.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2019

The effect of self-interaction error on electrostatic dipoles calculated using density functional theory

Spurious electron self-interaction in density functional approximations (DFAs) can lead to inaccurate predictions of charge transfer in heteronuclear molecules that manifest as errors in calculated electrostatic dipoles. Here we show the magnitude of these errors on dipoles computed for a diverse set of 47 molecules taken from the recent benchmark study of Hait and Head-Gordon. We compare results of Perdew-Wang local spin density approximation (PW92), Perdew-Burke-Ernzerhof (PBE) generalized gradient approximation (GGA), and strongly constrained and appropriatedly normed (SCAN) meta-GGA dipole calculations, along with those of their respective self-interaction-corrected (SIC) counterparts, to reference values from accurate wave function-based methods. The SIC calculations were carried out using the Fermi-Löwdin orbital (FLO-SIC) approach. We find that correcting for self-interaction generally increases the degree of charge transfer, thereby increasing the size of calculated dipole moments. The FLO-SIC-PW92 and FLO-SIC-PBE dipoles are in better agreement with reference values than their uncorrected DFA counterparts, particularly for strongly ionic molecules where significant improvement is seen. Applying FLO-SIC to SCAN does not improve dipole values overall. In addition, we show that removing self-interaction improves the description of the dipole for stretched-bond geometries and recovers the physically correct separated atom limit of zero dipole. Finally, we find that the best agreement between the FLO-SIC-DFA and reference dipoles occurs when the molecular geometries are optimized using the FLO-SIC-DFA.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2026

Quantum solver for single-impurity Anderson models with particle-hole symmetry

Quantum embedding methods, such as dynamical mean-field theory (DMFT), provide a powerful framework for investigating strongly correlated materials. A central computational bottleneck in DMFT is in solving the Anderson impurity model (AIM), whose exact solution is classically intractable for large bath sizes. In this work, we benchmark a quantum-classical hybrid solver tailored for particle-hole symmetric AIMs, using the variational quantum eigensolver to prepare the ground state of the model with shallow quantum circuits. The solver uses shallow quantum ansätze and one set of variational parameters to prepare the ground state and its particle and hole excitations, enabling the construction of the impurity Green’s function through a continued-fraction expansion. We evaluate the performance of this approach across a few bath sizes and interaction strengths under noisy, shot-limited conditions. We compare three optimization routines (COBYLA, Adam, and L-BFGS-B) in terms of convergence and fidelity, assess the benefits of estimating a quantum-computed moment correction to the variational energies, and benchmark the approach by comparing the density of states computed from the impurity Green’s function against that obtained using a classical pipeline. Our results demonstrate the feasibility of Green’s function construction on near-term devices and establish practical benchmarks for quantum impurity solvers embedded within self-consistent DMFT loops.

Karabin, Mariia [ORNL]↗

DOE OSTI2023

Technoeconomic assessment of distillation heat transfer intensification using aeroelastically fluttering reeds

Dry cooling, where forced air is the heat transfer medium, is a preferable cooling method in arid locations lacking readily available process water. However, such locations often experience high ambient temperatures that limit the effectiveness of air cooling. The objective of this study is to quantify the economic and energetic benefits of heat transfer intensification via the implementation of aeroelastically fluttering reeds to the air-cooled condenser of a methanol distillation column. Condenser size and performance, regarding recovered methanol and required fan power, is evaluated across condenser operating temperatures (T cond ) from 60 to 62°C and heat transfer coefficients (U) U base –2U base for a range of inlet air temperatures based on ambient temperature data from Yuma, Arizona. Under typical design sizing, condenser capital cost was reduced by 6%–35% (1.3U base –2U base ) and nominal methanol recovery was increased from 0.26% to 0.38% (T cond = 62–60°C). At optimized condenser size, all enhanced U and T cond pairs increase methanol recovery and reduce fan power costs compared to the optimal Ubase reference. Overall, using enhanced heat transfer to maintain condenser temperature under a wider range of inlet conditions, rather than to reduce operation temperature, produces more favorable performance. Methanol price is not a determining factor in which pairs are profitable. Analysis was repeated for a global warming scenario, revealing more valuable improvements under elevated temperatures. Energy savings from condenser improvement to a methanol production system are not significant with respect to an optimized conventional system. Furthermore, unit economic and energetic incentives suggest implementation of fluttering reeds may be justified in other applications.

42 ENGINEERING↗