SEARCH · Search NASA

Results for “SIGNAL REFLECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Anthropometric data error detecting and correction with a computer

Data obtained with automated anthropometric data aquisition equipment was examined for short term errors. The least squares curve fitting technique was used to ascertain which data values were erroneous and to replace them, if possible, with corrected values. Errors were due to random reflections of light, masking of the light rays, and other types of optical and electrical interference. It was found that the signals were impossible to eliminate from the initial data produced by the television cameras, and that this was primarily a software problem requiring a digital computer to refine the data off line. The specific data of interest was related to the arm reach envelope of a human being.

Chesak, D. D.↗

NASA NTRS1982

Analysis of combustion spectra containing organ pipe tone by cepstral techniques

Signal reinforcements and cancellations due to standing waves may distort constant bandwidth combustion spectra. Cepstral techniques previously applied to the ground reflection echo problem are used to obtain smooth broadband data and information on combustion noise propagation. Internal fluctuating pressure measurements made using a J47 combustor attached to a 6.44 m long duct are analyzed. Measurements made with Jet A and hydrogen fuels are compared. The acoustic power levels inferred from the measurements are presented for a range of low heat release rate operating conditions near atmospheric pressure. For these cases, the variation with operating condition of the overall acoustic broadband power level for both hydrogen and Jet A fuels is consistent with previous results showing it was proportional to the square of the heat release rate. However, the overall acoustic broadband power level generally is greater for hydrogen than for Jet A.

Miles, J. H.↗

NASA NTRS1986

Analytical ultrasonics for evaluation of composite materials response. Part 1: Physical interpretation

The phenomena associated with the propagation of elastic waves in anisotropic materials are discussed. Wave modes propagating in general directions relative to the material coordinate system are not purely longitudinal nor transverse. Hence the generation of ultrasonic waves by common piezoelectric transducers will generate multiple modes to some extent. The received signals will likely be a combination of different modes. When using two transducers to send and receive ultrasonic waves, deviation of the energy flux vector may reduce the apparent value of the received signal unless the proper orientation of the two transducers with respect to one another is taken into account. And application of reflection from plane boundaries for the purposes of making certain measurements may lead to misinterpretation of results unless one is aware of the differences in multiple mode generation and critical angle phenomena between isotropic and anisotropic materials. When studies or characterizations of composite materials by ultrasonics are to be performed, these phenomena must be taken into consideration so that proper and correct application and interpretation of the measurements can be made. Finally, attention must be drawn again to the fact that composite materials are heterogeneous by definition. The results discussed here have been determined for homogeneous materials only. While the assumption of homogeneity appears to be valid for certain wavelength ranges in composites, future work must continue to study the phenomena of wave propagation in anisotropic, nonhomogeneous materials.

Henneke, E. G., II↗

NASA NTRS1990

High resolution derivative spectra in remote sensing

The use of derivative spectra is an established technique in analytical chemistry for the elimination of background signals and for resolving overlapping spectral features. Application of this technique for tackling analogous problems such as interference from soil background reflectance in the remote sensing of vegetation or for resolving complex spectra of several target species within individual pixels in remote sensing is proposed. Methods for generating derivatives of high spectral resolution data are reviewed. Results of experiments to test the use of derivatives for monitoring chlorosis in vegetation show that derivative spectral indices are superior to conventional broad-band spectral indices such as the near-infrared/red reflectance ratio. Conventional broad-band indices are sensitive to both leaf cover as well as leaf color. New derivative spectral indices which were able to monitor chlorosis unambiguously were identified. Potential areas for the application of this technique in remote sensing are considered.

Demetriades-Shah, Tanvir H.↗

NASA NTRS1994

Adjustable Optical-Fiber Attenuator

Adjustable fiber-optic attenuator utilizes bending loss to reduce strength of light transmitted along it. Attenuator functions without introducing measurable back-reflection or insertion loss. Relatively insensitive to vibration and changes in temperature. Potential applications include cable television, telephone networks, other signal-distribution networks, and laboratory instrumentation.

Buzzetti, Mike F.↗

NASA NTRS1994

Hubble Space Telescope UV spectral observations of Io passing into eclipse

Time-resolved spectra of Io have been obtained with the Faint Object Spectrograph on the Hubble Space Telescope in January 1992 at times centered on the passage of Io into Jupiter's shadow. Two different eclipse observations covered 1100-1600 A and 2250-3300 A. In the far ultraviolet(far-UV) range, emission lines of atomic sulfur and oxygen from Io's atmosphere (similar to those previously detected with the International Ultraviolet Explorer (IUE)) have been observed from Io in sunlight, and the spatial extent of the emitting region has been resolved for the first time: this is 0.5-1 Io radii (R(sub Io)) above the surface. The emission lines are typically 1kR in brightness while Io is in sunlight, and decrease to a few hundred Rayleighs within 20 min or less of Io's passing into shadow. If the emissions are produced in Io's ionosphere, the decrease in shadow appears consistent with the collisional slowing and recombination of photoelectrons in 100-1000 s, with recombination an important quenching process if the dominant ion is molecular (i.e., SO2(+)) condensation, with the residual emission in shadow due either to plasma impact of gas above the hot volcanic calderas or electron impact on S and O. In the near-UV range, we have not detected any airglow emissions from Io's atmosphere in shadow, with the main limitation being a high level of scattered light from Jupiter. We derive a 3 sigma upper limit to the 2560 A SO emission feature of 1 KR, which is close to what is expected from electron impact on SO2 based on the obs erved brightness of the FUV S and O lines in shadow. A high signal-to-noise spectrum of Io's albedo in sunlight reveals a spectral shape similar to laboratory spectra of SO2 frost reflectivity, and the relative albedo spectrum changed as Io passed into eclipse and part of the disk was in shadow. No specific SO2 gas absorption features appear in the albedo spectrum, although there could be substantial gas absorption near 2800 A if the individual lines are narrow and saturated. Finally, we present preliminary models for the near-UV spectrum of Io as functions of SO2 frost areal coverage and SO2 gas density.

Clarke, John T.↗

NASA NTRS1995

Beat frequency ultrasonic microsphere contrast agent detection system

A system for and method of detecting and measuring concentrations of an ultrasonically-reflective microsphere contrast agent involving detecting non-linear sum and difference beat frequencies produced by the microspheres when two impinging signals with non-identical frequencies are combined by mixing. These beat frequencies can be used for a variety of applications such as detecting the presence of and measuring the flow rates of biological fluids and industrial liquids, including determining the concentration level of microspheres in the myocardium.

Pretlow, Robert A., III↗

NASA NTRS2001

Investigating the Effect of Impurities on Macromolecule Crystal Growth in Microgravity

Chicken egg-white lysozyme (CEWL) crystals were grown in microgravity and on the ground in the presence of various amounts of a naturally occurring lysozyme dimer impurity. No significant favorable differences in impurity incorporation between microgravity and ground crystal samples were observed. At low impurity concentration the microgravity crystals preferentially incorporated the dimer. The presence of the dimer in the crystallization solutions in microgravity reduced crystal size, increased mosaicity and reduced the signal to noise ratio of the X-ray data. Microgravity samples proved more sensitive to impurity. Accurate indexing of the reflections proved critical to the X-ray analysis. The largest crystals with the best X-ray diffraction properties were grown from pure solution in microgravity.

Snell, Edward H.↗

NASA NTRS1995

Fiber Optic Attenuators

Mike Buzzetti designed a fiber optic attenuator while working at Jet Propulsion Laboratory, intended for use in NASA's Deep Space Network. Buzzetti subsequently patented and received an exclusive license to commercialize the device, and founded Nanometer Technologies to produce it. The attenuator functions without introducing measurable back-reflection or insertion loss, and is relatively insensitive to vibration and changes in temperature. Applications include cable television, telephone networks, other signal distribution networks, and laboratory instrumentation.

Source record↗

NASA NTRS2002

Retrieval Of Cloud Pressure And Chlorophyll Content Using Raman Scattering In GOME Ultraviolet Spectra

Reliable cloud pressure estimates are needed for accurate retrieval of ozone and other trace gases using satellite-borne backscatter ultraviolet (buv) instruments such as the global ozone monitoring experiment (GOME). Cloud pressure can be derived from buv instruments by utilizing the properties of rotational-Raman scattering (RRS) and absorption by O2-O2. In this paper we estimate cloud pressure from GOME observations in the 355-400 nm spectral range using the concept of a Lambertian-equivalent reflectivity (LER) surface. GOME has full spectral coverage in this range at relatively high spectral resolution with a very high signal-to-noise ratio. This allows for much more accurate estimates of cloud pressure than were possible with its predecessors SBUV and TOMS. We also demonstrate the potential capability to retrieve chlorophyll content with full-spectral buv instruments. We compare our retrieved LER cloud pressure with cloud top pressures derived from the infrared ATSR instrument on the same satellite. The findings confirm results from previous studies that showed retrieved LER cloud pressures from buv observations are systematically higher than IR-derived cloud-top pressure. Simulations using Mie-scattering radiative transfer algorithms that include O2-O2 absorption and RRS show that these differences can be explained by increased photon path length within and below cloud.

Atlas, Robert↗

NASA NTRS1985

Portable instant display and analysis reflectance spectrometer

A portable analysis spectrometer (10) for field mineral identification is coupled to a microprocessor (11) and memory (12) through a bus (13) and A/D converter (14) to display (16) a spectrum of reflected radiation in a band selected by an adjustable band spectrometer (20) and filter (23). A detector array (21) provides output signals at spaced frequencies within the selected spectrometer band which are simultaneously converted to digital form for display. The spectrum displayed is compared with a collection of spectra for known minerals. That collection is stored in memory and selectively displayed with the measured spectrum, or stored in a separate portfolio. In either case, visual comparison is made. Alternatively, the microprocessor may use an algorithm to make the comparisons in search for the best match of the measured spectrum with one of the stored spectra to identify the mineral in the target area.

Goetz, Alexander F. H.↗

NASA NTRS1997

Beat frequency ultrasonic microsphere contrast agent detection system

Pretlow, III, Robert A.↗

NASA NTRS2016

Consistency of Vegetation Index Seasonality Across the Amazon Rainforest

Vegetation indices (VIs) calculated from remotely sensed reflectance are widely used tools for characterizing the extent and status of vegetated areas. Recently, however, their capability to monitor the Amazon forest phenology has been intensely scrutinized. In this study, we analyze the consistency of VIs seasonal patterns obtained from two MODIS products: the Collection 5 BRDF product (MCD43) and the Multi-Angle Implementation of Atmospheric Correction algorithm (MAIAC). The spatio-temporal patterns of the VIs were also compared with field measured leaf litterfall, gross ecosystem productivity and active microwave data. Our results show that significant seasonal patterns are observed in all VIs after the removal of view-illumination effects and cloud contamination. However, we demonstrate inconsistencies in the characteristics of seasonal patterns between different VIs and MODIS products. We demonstrate that differences in the original reflectance band values form a major source of discrepancy between MODIS VI products. The MAIAC atmospheric correction algorithm significantly reduces noise signals in the red and blue bands. Another important source of discrepancy is caused by differences in the availability of clear-sky data, as the MAIAC product allows increased availability of valid pixels in the equatorial Amazon. Finally, differences in VIs seasonal patterns were also caused by MODIS collection 5 calibration degradation. The correlation of remote sensing and field data also varied spatially, leading to different temporal offsets between VIs, active microwave and field measured data. We conclude that recent improvements in the MAIAC product have led to changes in the characteristics of spatio-temporal patterns of VIs seasonality across the Amazon forest, when compared to the MCD43 product. Nevertheless, despite improved quality and reduced uncertainties in the MAIAC product, a robust biophysical interpretation of VIs seasonality is still missing.

MAIAC↗

NASA NTRS2018

Methods for Passive Optical Detection and Relative Navigation for Rendezvous with a Non-Cooperative Object at Mars

Long-range passive optical detection of an orbiting inert sphere by a robotic Mars orbiter is investigated and trades are described in terms of detectability via reflected visible light in the presence of orbit uncertainty, gravitational perturbations, and camera electronics noise. A new approximate equation for signal-tonoise ratio (SNR) is developed to include most relevant camera imperfections, diffraction, and stray light from the Mars limb as relevant to this scenario. Using this method, a notional camera suite is designed to meet detection, navigation, and redundancy requirements for an example mission scenario. Results from a simulation tool demonstrate the long-range initial detection strategy in the presence of perturbations from various sources. Finally, navigation analysis shows that the information gathered using passive optical detection is sufficient to begin orbit matching.

Woolley, Ryan C.↗

DOE OSTI2021

Temporally and spatially resolved X-ray densitometry in a shock tube

Gas densities were measured by x-ray absorption spectroscopy to examine spatial inhomogeneity in density behind incident and reflected shock waves in a miniature (12.7 mm bore) high repetition rate shock tube. Shock waves were generated in argon. The pressure and temperature behind the incident shock were P 2 ~ 1.72 bar and T 2 ~ 800 K, while those behind the reflected shock were P 5 ~ 6.5 bar and T 5 ~ 1480 K. Time-resolved line-of-sight transmission measurements using x-rays at 9 keV photon energy were made along various axial and transverse locations covering the entire shock tube cross section. The x-ray transmission at each location was converted to pathlength-integrated densities, which in some conditions could be further converted to pathlength-averaged densities. The measured gas densities were compared with those calculated by the normal shock wave relations, and good agreement was found in the preshock and immediately behind the incident shock regions. Similar agreement was found for reflected shock conditions very near the endwall. However, increasingly large differences between the measured and calculated gas densities were found as distance from the endwall increased. Furthermore, reconstruction by Abel inversion allowed time and radially resolved densities to be obtained from the transverse measurements. While the profiles measured in this experiment are of insufficient signal-to noise level and resolution to definitively assign boundary layer thicknesses, future improvements may be able to do this. The radially resolved densities reveal growing sidewall thermal boundary layers in gases behind the reflected shock. These reconstructions were compared with a model of the thermal boundary layer and are consistent with values of the thermal boundary layer thickness being between 0.25 mm and 1 mm at 0.7 ms after shock reflection.

42 ENGINEERING↗

DOE OSTI2025

Applying Linear Optics from Closed Orbits Modulation for finding beam-based alignment of harmonic sextupoles

A fast and accurate beam-based alignment (BBA) method for harmonic sextupoles has been devel oped at NSLS-II using Linear Optics from Closed Orbit Modulation (LOCOM). The approach excites the beam with simultaneous sine-wave signals at two fast correctors, chosen with an appropriate phase advance to span the full betatron phase space. This strategy suppresses systematic errors from hysteresis, while additional errors from orbit drift and power-supply calibration are minimized by the short measurement time (a few minutes) and reliance solely on beam-based current-to-field conver sion of the sextupoles, with hysteresis explicitly included. Simulations indicate that Linear Optics from Closed Orbits (LOCO) combined with 0.5 mm local orbit bumps can resolve relative sextupole field offsets (∆k₂) with precision better than 10% of k₂, reflecting to beam-based alignment (BBA) accuracy finer than 50 µm. Moreover, employing machine-learning-optimized local orbit bumps en hances sextupole-induced quadrupole signals in a deterministic manner and maintains orbit stability under large sextupole strength variations (±40%). The proposed method is experimentally validated through proof-of-principle measurements at NSLS-II, demonstrating its potential as a fast, precise, and robust tool for harmonic sextupole alignment.

43 PARTICLE ACCELERATORS↗

NASA NTRS1999

Resonant Transmissive Modulator Construction for Use in Beam Steering Array

An agile electronically configurable optical beam steering device for use in directional free-space transmission of optical signals is described. The device design employs an array of tunable resonant transmissive modulators constructed from multi-layered stacks of electro-optically active dielectric materials. Each modulator may be individually configured to transmit an optical signal with a specific amount of phase and group velocity modulation. The resulting diffractive interactions between modulator outputs provide a method for directional optical signal transmission. Of particular focus within this presentation is the optimized design of the individual modulator. It is widely known that periodic multi-layered stacks of dielectric materials exhibit reflective and transmissive resonances as described by the stack's transmission function. If an electric field is applied normal to the stack's layers, phenomena such as the electro-optic effect and/or the quantum-confined Stark effect may be employed to change the effective refractive index within the stack. This refractive index change alters the stack's transmission function and modulates the phase and group velocity of the transmitted optical signal. By varying the parameters that describe the stack's specific construction and operation, such as number of layers within the stack, refractive indexes of stack materials, layer thicknesses, and combinations of periodic verses non-periodic layer repetitions, custom transmittance functions may be generated. The transmitted optical signal carrier frequency and bandwidth must be carefully selected to maximize transmission and to minimize absorption. A computational optimization of the variables describing the stack's construction strives to maximize the amount of optical signal modulation verses applied voltage. Trade-offs between methods of increasing device performance verses the limitations of fabrication technologies are considered.

Keys, Andrew S.↗

DOE OSTI2024

Optimizing Transmission of Acoustic Signals to Monitor Internal Conditions of Canisters for Dry Storage of Commercial Spent Nuclear Fuel

Safe storage of spent nuclear fuel (SNF) is critical to the nuclear fuel cycle and the future of nuclear energy. In the United States, SNF is stored primarily via two methods regulated by the U.S. Nuclear Regulatory Commission: wet storage in SNF pools and dry storage in dry cask storage systems (DCSSs). After about five years of cooling in spent fuel pools, the fuel assemblies are transferred into DCSSs, and the systems are filled with helium and sealed by welding. Deterioration of conditions inside of a DCSS is reflected in changes in the internal gas properties; this motivates the development of acoustic techniques to monitor internal gas properties, over extended storage periods, using sensors mounted on the exterior of the storage packages. However, a major challenge in collecting acoustic signals is the impedance mismatch between the steel canister shell and the gas. Only a small fraction of the ultrasonic signal can be transmitted through the gas medium. This paper documents experimental studies conducted on a full-scale canister mock-up to capture the gas-borne signals. Damping materials were pasted on the outside, and blocking and unblocking tests were conducted to identify the gas-borne signal. The results show that the excitation frequency plays an important role in maximizing the gas-borne signals. The gas-borne signal was successfully detected at around the theoretical time-of-flight. A high signal-to-noise ratio was achieved in the measurements. Next, the acoustic impedance matching layers were introduced, and the gas signal was drastically improved compared with that using no AIM layers.

Spent nuclear fuel (SNF), Canisters, Internal cond↗