Search NASA⌕ Search

SEARCH · Search NASA

Results for “Two Phase Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Multilayer Coextrusion of Polymer Composites to Develop Organic Capacitors

Multilayer coextrusion is applied to produce a tape containing layers of alternating electrical properties to demonstrate the potential for using coextrusion to manufacture capacitors. To obtain the desired properties, we develop two filled polymer systems, one for conductive layers and one for dielectric layers. We describe numerical models used to help determine the material and processing parameters that impact processing and layer stability. These models help quantify the critical ratios of densities and viscosities of the two layers to maintain stable layers, as well as the effect of increasing the flow rate of one of the two materials. The conducting polymer is based on polystyrene filled with a blend of low-melting-point eutectic metal and nickel particulate filler, as described by Mrozek et al. (2010). The appropriate concentrations of fillers are determined by balancing measured conductivity with processability in a twin screw extruder. Based on results of the numerical models and estimates of the viscosity of emulsions and suspensions, a dielectric layer composed of polystyrene filled with barium titanate is formulated. Despite the fact that the density of the dielectric filler is less than the metallic filler of the conductive phase, as well as rheological measurements that later showed that the dielectric formulation is not an ideal match to the viscosity of the conductive material, the two materials can be successfully coextruded if the flow rates of the two materials are not identical. A measurable capacitance of the layered structure is obtained.

36 MATERIALS SCIENCE↗

Dynamic Modeling and Control Studies of a Two-Stage Bubbling Fluidized Bed Adsorber-Reactor for Solid-Sorbent CO{sub 2} Capture

A one-dimensional, non-isothermal, pressure-driven dynamic model has been developed for a two-stage bubbling fluidized bed (BFB) adsorber-reactor for solid-sorbent carbon dioxide (CO{sub 2}) capture using Aspen Custom Modeler® (ACM). The BFB model for the flow of gas through a continuous phase of downward moving solids considers three regions: emulsion, bubble, and cloud-wake. Both the upper and lower reactor stages are of overflow-type configuration, i.e., the solids leave from the top of each stage. In addition, dynamic models have been developed for the downcomer that transfers solids between the stages and the exit hopper that removes solids from the bottom of the bed. The models of all auxiliary equipment such as valves and gas distributor have been integrated with the main model of the two-stage adsorber reactor. Using the developed dynamic model, the transient responses of various process variables such as CO{sub 2} capture rate and flue gas outlet temperatures have been studied by simulating typical disturbances such as change in the temperature, flowrate, and composition of the incoming flue gas from pulverized coal-fired power plants. In control studies, the performance of a proportional-integral-derivative (PID) controller, feedback-augmented feedforward controller, and linear model predictive controller (LMPC) are evaluated for maintaining the overall CO{sub 2} capture rate at a desired level in the face of typical disturbances.

42 ENGINEERING↗

Multiphase lattice Boltzmann simulations for porous media applications

Over the last two decades, lattice Boltzmann methods have become an increasingly popular tool to compute the flow in complex geometries such as porous media. In addition to single phase simulations allowing, for example, a precise quantification of the permeability of a porous sample, a number of extensions to the lattice Boltzmann method are available which allow to study multiphase and multicomponent flows on a pore scale level. In this work, we give an extensive overview on a number of these diffuse interface models and discuss their advantages and disadvantages. Furthermore, we shortly report on multiphase flows containing solid particles, as well as implementation details and optimization issues.

42 ENGINEERING↗

Generating one-column grids with fractal flow dimension

The grid generation capability built into the numerical simulator TOUGH for multi-phase fluid and heat flow through geologic media can create one-column grids with linear or radial geometry, corresponding to one-dimensional or two-dimensional radial flow, respectively. The integral-finite-difference-method that TOUGH employs for spatial discretization makes it very simple to generalize the grid-generation algorithm from integer to non-integer (fractal) flow dimension. Here the grid-generation algorithm is generalized to create one-column grids with fractal flow dimension ranging from less than 1 to 3. The fractal grid generation method is verified by comparing numerical simulation results to an analytical solution for a generalized Theis solution for integer and non-integer flow dimensions between 0.4 and 3. It is then applied to examine gas production decline curves from hydraulically fractured shale that is modeled as a fractal-dimensioned fracture network with flow dimensions between 0.25 and 3. Grids with fractal flow dimension are useful for representing flow through fracture networks or highly heterogeneous geologic media with fractal geometry, and may be particularly useful for inverse methods.

58 GEOSCIENCES↗

Mimicking Natural Systems: Methane Hydrate Formation-Decomposition in Depleted Sediments

We have initiated a systematic study of sediment-hydrate interaction under subsurface-mimic conditions to initially focus on marine hydrates. A major obstacle to studying natural hydrate systems has been the absence of a sophisticated mimic apparatus in which the hydrate formation phenomenon can be reproduced with precision. We have designed and constructed a bench-top unit, namely flexible integrated study of hydrates (FISH), for this purpose. The unit is fully instrumented to precisely record temperatures, pressures and changes in gas volume during absorption/evolution. The Labview software allows rapid and continuous data collection during the hydrate formation/dissociation cycle. In our integrated approach, several host sediments collected from Blake Ridge, a well-researched hydrate site, were characterized using the computed microtomography technique at Beamline X-26A of the National Synchrotron Light Source at Brookhaven National Laboratory. The characterized depleted sediments were then used to study the hydrate formation/decomposition kinetics under various pressures in the FISH unit. We report two hydrate formation methods: one under continuous methane gas-flow conditions (dynamic mode) and the other in which hydrates are formed from the dissolved gas phase by diffusion (static mode). Also reported is a depressurization method, namely the step-down pressure method, to yield gas evolution data. Data from such runs with host sediment from the deepest site (667 metres) is presented. During hydrate formation, the data reveals a temperature signature that is consistent with an exothermic hydrate formation event. In the decomposition cycle, data at various pressures was analysed to yield curves with similar slopes, suggesting a zero-order dependence. The capabilities of the FISH unit and the implications of these runs in establishing a database of sediment-hydrate kinetics and pore saturation are discussed.

03 NATURAL GAS↗

On the Use of NLDAS2 Weather Data for Hydrologic Modeling in the Upper Mississippi River Basin

Weather data are the key forces that drive hydrological processes so that their accuracy in watershed modeling is fundamentally important. For large-scale watershed modeling, weather data are either generated by using interpolation methods or derived from assimilated datasets. In the present study, we compared model performances of the Soil and Water Assessment Tool (SWAT), as driven by interpolation weather data, and NASA North American Land Data Assimilation System Phase Two (NLDAS2) weather dataset in the Upper Mississippi River Basin (UMRB). The SWAT model fed with different weather datasets were used to simulate monthly stream flow at 11 United States Geological Survey (USGS) monitoring stations in the UMRB. Model performances were evaluated based on three metrics: coefficient of determination (R 2 ), Nash–Sutcliffe coefficient (NS), and percent bias (P bias ). The results show that, after calibration, the SWAT model compared well at all monitoring stations for monthly stream flow using different weather datasets indicating that the SWAT model can adequately produce long-term water yield in UMRB. The results also show that using NLDAS2 weather dataset can improve SWAT prediction of monthly stream flow with less prediction uncertainty in the UMRB. We concluded that NLDAS2 dataset could be used by the SWAT model for large-scale watersheds like UMRB as a surrogate of the interpolation weather data. Further analyses results show that NLDAS2 daily solar radiation data was about 2.5 MJ m -2 higher than the interpolation data. As such, the SWAT model driven by NLDAS2 dataset tended to underestimate stream flow in the UMRB due to the overestimation in evapotranspiration in uncalibrated conditions. Thus, the implication of overestimated solar radiation by NLDAS2 dataset should be considered before using NLDAS2 dataset to drive the hydrological model.

54 ENVIRONMENTAL SCIENCES↗

OSCILLATION OF CURRENT SHEETS IN THE WAKE OF A FLUX ROPE ERUPTION OBSERVED BY THE SOLAR DYNAMICS OBSERVATORY

An erupting flux rope (FR) draws its overlying coronal loops upward, causing a coronal mass ejection. The legs of the overlying loops with opposite polarities are driven together. Current sheets (CSs) form, and magnetic reconnection, producing underneath flare arcades, occurs in the CSs. Employing Solar Dynamic Observatory /Atmospheric Imaging Assembly images, we study a FR eruption on 2015 April 23, and for the first time report the oscillation of CSs underneath the erupting FR. The FR is observed in all AIA extreme-ultraviolet passbands, indicating that it has both hot and warm components. Several bright CSs, connecting the erupting FR and the underneath flare arcades, are observed only in hotter AIA channels, e.g., 131 and 94 Å. Using the differential emission measure (EM) analysis, we find that both the temperature and the EM of CSs temporally increase rapidly, reach the peaks, and then decrease slowly. A significant delay between the increases of the temperature and the EM is detected. The temperature, EM, and density spatially decrease along the CSs with increasing heights. For a well-developed CS, the temperature (EM) decreases from 9.6 MK (8 × 10{sup 28} cm{sup −5}) to 6.2 MK (5 × 10{sup 27} cm{sup −5}) in 52 Mm. Along the CSs, dark supra-arcade downflows (SADs) are observed, and one of them separates a CS into two. While flowing sunward, the speeds of the SADs decrease. The CSs oscillate with a period of 11 minutes, an amplitude of 1.5 Mm, and a phase speed of 200 ± 30 km s{sup −1}. One of the oscillations lasts for more than 2 hr. These oscillations represent fast-propagating magnetoacoustic kink waves.

79 ASTRONOMY AND ASTROPHYSICS↗

On the genesis of molybdenum carbide phases during reduction-carburization reactions

Molybdenum carbide has been prepared according to the carbothermal reduction method. Carbon black substrate was used as C-source whereas a H{sub 2}-flow was the reducing agent. Two different H{sub 2} consumption steps were identified during the carburization treatment. The low temperature step is related to the reduction of Mo{sup 6+}-to-Mo{sup 4+}, the higher temperature process accounts for the deep reduction of Mo{sup 4+}-to-metal Mo{sup 0} and its subsequent reaction with C to form the Mo-carbide. The influences of the maximum carburization temperature, carburization time, gas hourly space velocity regarding Mo-loading, heating rate and temperature of Ar pre-treatment were analyzed. All these conditions are interrelated to each other. Thus, the carburization process ends at 700 Degree-Sign C when Mo-loading is 10 wt%, however Mo-loading higher than 10 wt% requires higher temperatures. Carburization temperatures up to 800 Degree-Sign C are needed to fulfill Mo-carbide formation with samples containing 50 wt% Mo. Nevertheless, Ar pre-treatment at 550 Degree-Sign C and slow heating rates favor the carburization, thus requiring lower carburization temperatures to reach the same carburization level. - Graphical Abstract: H{sub 2}-consumption profile (TPR) during the molybdenum carburization process, XRD patterns of the reduced Mo-samples after carburization and TEM-micrographs with two different enlargement of the samples with 5, 20 and 50 wt% Mo. Highlights: Black-Right-Pointing-Pointer Control of carburization variables: tailor the reduced/carbide Mo-phases (single/mixture). Black-Right-Pointing-Pointer Mo carburization in two stages: (1) Mo{sup 6+}-Mo{sup 4+}; (2) Mo{sup 4+}-Mo{sup 0} and, at once, MoC. Black-Right-Pointing-Pointer The carburization process is faster than Mo{sup 4+} reduction. Black-Right-Pointing-Pointer XPS probed: reduced Mo particles show core-shell structure. Black-Right-Pointing-Pointer Core: reduced Mo (Mo{sub 2}C, MoO{sub 2} and/or Mo{sup 0}); Shell: 2-3 nm of MoO{sub 3}.

36 MATERIALS SCIENCE↗

Advancing Thermal-Hydraulic Modeling Capabilities for Molten Salt Reactors in Pronghorn

This is an M2 report for the NEAMS program. This work focuses on advancing the modeling and simulation capabilities for Molten Salt Reactors (MSRs) within Pronghorn, addressing key thermal-hydraulic challenges that must be addressed for the safe and efficient operation of these advanced reactors. This report summarizes the development and validation of the following new models in Pronghorn: (i) two-equation RANS turbulence models, (ii) near-wall turbulence corrections due to curvature and roughness, and (iii) multidimensional two-phase drift-flux models. For each of these cases, along with the experimental validation, an application study of interest to MSRs is presented. In addition, this report also presents recent improvements in the domain-overlapping coupling between Pronghorn and SAM to address the cases of weakly compressible flow and flow reversal. Finally, an MSR action that greatly simplifies the setup of MSR models using NEAMS tools is described.

42 ENGINEERING↗

Oblique shock structures formed during the ablation phase of aluminium wire array z-pinches

A series of experiments has been conducted in order to investigate the azimuthal structures formed by the interactions of cylindrically converging plasma flows during the ablation phase of aluminium wire array Z pinch implosions. These experiments were carried out using the 1.4 MA, 240 ns MAGPIE generator at Imperial College London. The main diagnostic used in this study was a two-colour, end-on, Mach-Zehnder imaging interferometer, sensitive to the axially integrated electron density of the plasma. The data collected in these experiments reveal the strongly collisional dynamics of the aluminium ablation streams. The structure of the flows is dominated by a dense network of oblique shock fronts, formed by supersonic collisions between adjacent ablation streams. An estimate for the range of the flow Mach number (M = 6.2-9.2) has been made based on an analysis of the observed shock geometry. Combining this measurement with previously published Thomson Scattering measurements of the plasma flow velocity by Harvey-Thompson et al.[Physics of Plasmas 19, 056303 (2012)] allowed us to place limits on the range of the ZT{sub e} of the plasma. The detailed and quantitative nature of the dataset lends itself well as a source for model validation and code verification exercises, as the exact shock geometry is sensitive to many of the plasma parameters. Comparison of electron density data produced through numerical modelling with the Gorgon 3D MHD code demonstrates that the code is able to reproduce the collisional dynamics observed in aluminium arrays reasonably well.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Phase diagram and fixed-point structure of two-dimensional N=1 Wess-Zumino models

We study the phases and fixed-point structure of two-dimensional supersymmetric Wess-Zumino models with one supercharge. Our work is based on the functional renormalization group (RG) formulated in terms of a manifestly off-shell supersymmetric flow equation for the effective action. Within the derivative expansion, we solve the flow of the superpotential also including the anomalous dimension of the superfield. The models exhibit a surprisingly rich fixed-point structure with a discrete number of fixed-point superpotentials. Each fixed-point superpotential is characterized by its number of nodes and by the number of RG-relevant directions. In limiting cases, we find periodic superpotentials and potentials which confine the fields to a compact target space. The maximally IR-attractive fixed point has one relevant direction, the tuning of which distinguishes between supersymmetric and broken phases. For the Wess-Zumino model defined near the Gaussian fixed point, we determine the phase diagram and compute the corresponding ground-state masses.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Development of a Hybrid Single/Two-Phase Capillary-Based Micro-Cooler using Copper Inverse Opals Wick with Silicon 3D Manifold for High-Heat-Flux Cooling Application

Previously, we reported two-phase capillary-based cooling using narrow (200 to 1000 ..mu..m) heater bridge copper inverse opal (CIO) wicks with heat flux level of 1400 Wcm -2 and superheat ~ 10 degrees C. Here, we demonstrate the area scaling of the proposed technology to a large-area micro-cooler for high-heat-flux cooling of microprocessors and power electronics. We developed a hybrid single/two-phase micro-cooler that relies on capillary-wicking in a 25-..mu..m-thick CIO with an open silicon microchannel 3D-manifold for liquid delivery and vapor extraction, achieving a high heat flux ~ 400 Wcm -2 over a heated area of 10 x 10 mm 2 . For a range of inlet water flowrates from 5 to 60 g(min) -1 , we achieved total thermal resistances and vapor qualities of 0.68 cm 2 degrees CW -1 to 0.2 cm 2 degrees CW -1 and 0.55 to 0.12, respectively. The flowrates are 10x smaller than those of conventional single- or two-phase microchannel cooling technology. The corresponding two-phase thermal resistances ranges from 0.05 to 0.02 cm 2 degrees CW -1 with temperature superheat of 8 to 6 degrees C, respectively. While the overall performance of the large-area (10 x 10 mm 2 ) capillary-based micro-cooler degraded compared to the previous demonstration of the technology for a heated area of 5 x 5 mm 2 , however, preliminary CFD modeling indicates that an improved manifold design will be able to achieve comparable performance.

capillary flow↗

Approaches for Water Removal in Direct-Fired sCO 2 Power Cycles

There is interest in investigation of water removal processes in direct fired sCO 2 flows, as this may potentially lead to greater system efficiency as the removal of this contaminant will result in sCO 2 behaving close to idealized behaviors. Water removal should be split into a two-step process, condensation of the water, followed by separation of the liquid phase water from the sCO 2 . The two main avenues of condensation are manipulation of pressure and temperature for phase change. For this paper, temperature-based phase change is the primary focus through the implementation of heat exchangers. Of the heat exchangers investigated it was found that printed circuit heat exchangers (PCHEs) could be an alternative for this use case, though the specific design of flow channel geometry and flow direction depends on the specific system case and cannot be determined at this point. For water separation there were four processes identified, all of which already assume water is in liquid phase at that point in the system. Of these separation avenues the best candidate is the hydrocyclone as it has a proven history of separating liquid-liquid phase mixtures with small density differences in oilfield use, in addition they have been investigated and modeled specifically for water separation for sCO 2 flows and the footprint is relatively small.

20 FOSSIL-FUELED POWER PLANTS↗

Neutron tomography of axially symmetric objects using 14 MeV neutrons from a portable neutron generator

In nuclear boiling water reactor cores, the distribution of water and steam (void) is essential for both safety and efficiency reasons. In order to enhance predictive capabilities, void distribution assessment is performed in two-phase test-loops under reactor-relevant conditions. This article proposes the novel technique of fast-neutron tomography using a portable deuterium-tritium neutron generator to determine the time-averaged void distribution in these loops. Fast neutrons have the advantage of high transmission through the metallic structures and pipes typically concealing a thermal-hydraulic test loop, while still being fairly sensitive to the water/void content. However, commercially available fast-neutron generators also have the disadvantage of a relatively low yield and fast-neutron detection also suffers from relatively low detection efficiency. Fortunately, some loops are axially symmetric, a property which can be exploited to reduce the amount of data needed for tomographic measurement, thus limiting the interrogation time needed. In this article, three axially symmetric test objects depicting a thermal-hydraulic test loop have been examined; steel pipes with outer diameter 24 mm, thickness 1.5 mm, and with three different distributions of the plastic material POM inside the pipes. Data recorded with the FANTOM fast-neutron tomography instrument have been used to perform tomographic reconstructions to assess their radial material distribution. Here, a dedicated tomographic algorithm that exploits the symmetry of these objects has been applied, which is described in the paper. Results are demonstrated in 20 rixel (radial pixel) reconstructions of the interior constitution and 2D visualization of the pipe interior is demonstrated. The local POM attenuation coefficients in the rixels were measured with errors (RMS) of 0.025, 0.020, and 0.022 cm{sup −1}, solid POM attenuation coefficient. The accuracy and precision is high enough to provide a useful indication on the flow mode, and a visualization of the radial material distribution can be obtained. A benefit of this system is its potential to be mounted at any axial height of a two-phase test section without requirements for pre-fabricated entrances or windows. This could mean a significant increase in flexibility of the void distribution assessment capability at many existing two-phase test loops.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

TOWARD A MAGNETOHYDRODYNAMIC THEORY OF THE STATIONARY ACCRETION SHOCK INSTABILITY: TOY MODEL OF THE ADVECTIVE-ACOUSTIC CYCLE IN A MAGNETIZED FLOW

The effect of a magnetic field on the linear phase of the advective-acoustic instability is investigated as a first step toward a magnetohydrodynamic (MHD) theory of the stationary accretion shock instability taking place during stellar core collapse. We study a toy model where the flow behind a planar stationary accretion shock is adiabatically decelerated by an external potential. Two magnetic field geometries are considered: parallel or perpendicular to the shock. The entropy-vorticity wave, which is simply advected in the unmagnetized limit, separates into five different waves: the entropy perturbations are advected, while the vorticity can propagate along the field lines through two Alfven waves and two slow magnetosonic waves. The two cycles existing in the unmagnetized limit, advective-acoustic and purely acoustic, are replaced by up to six distinct MHD cycles. The phase differences among the cycles play an important role in determining the total cycle efficiency and hence the growth rate. Oscillations in the growth rate as a function of the magnetic field strength are due to this varying phase shift. A vertical magnetic field hardly affects the cycle efficiency in the regime of super-Alfvenic accretion that is considered. In contrast, we find that a horizontal magnetic field strongly increases the efficiencies of the vorticity cycles that bend the field lines, resulting in a significant increase of the growth rate if the different cycles are in phase. These magnetic effects are significant for large-scale modes if the Alfven velocity is a sizable fraction of the flow velocity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Increasing the Separation Capacity of Intact Histone Proteoforms Chromatography Coupling Online Weak Cation Exchange-HILIC to Reversed Phase LC UVPD-HRMS

Top-down proteomics is an emerging analytical strategy to characterize combinatorial protein post-translational modifications (PTMs). However, sample complexity and small mass differences between chemically closely related proteoforms often limit the resolution attainable by separations employing a single liquid chromatographic (LC) principle. In particular, for ultra-modified proteins like histones, extensive and time-consuming fractionation is needed to achieve deep proteoform coverage. Herein, we present the first online nano-flow comprehensive two-dimensional liquid chromatography (nLC×LC) platform top-down mass spectrometry analysis of histone proteoforms. The described two-dimensional LC system combines weak cation exchange chromatography under hydrophilic interaction LC conditions (i.e. charge- and hydrophilicity-based separation) with reversed phase liquid chromatography (i.e. hydrophobicity-based separation). The two independent chemical selectivities were run at nanoflows (300 nL/min) and coupled online with high-resolution mass spectrometry employing ultraviolet photodissociation (UVPD-HRMS). The nLC×LC workflow increased the number of intact protein masses observable relative to one-dimensional approaches and allowed characterization of hundreds of proteforms starting from limited sample quantities (~1.5 µg).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Charge Transfer Dynamics of Phase-Segregated Halide Perovskites: CH 3 NH 3 PbCl 3 and CH 3 NH 3 PbI 3 or (C 4 H 9 NH 3 ) 2 (CH 3 NH 3 ) n -1 Pb n I 3 n +1 Mixtures

Lead halide perovskites present a versatile class of solution-processable semiconductors with highly tunable bandgaps that span ultraviolet, visible, and near-infrared portions of the spectrum. We explore phase-separated chloride and iodide lead perovskite mixtures as candidate materials for intermediate band applications in future photovoltaics. X-ray diffraction and scanning electron microscopy reveal that deposition of precursor solutions across the MAPbCl 3 /MAPbI 3 composition space affords quasi-epitaxial cocrystallized films, in which the two perovskites do not alloy but instead remain phase-segregated. First-principle calculations further support the formation of an epitaxial interface and predict energy offsets in the valence band and conduction band edges that could result in intermediate energy absorption. The charge dynamics of variable mixtures of the relatively narrow bandgap (1.57 eV) MAPbI 3 perovskite and wide bandgap (3.02 eV) MAPbCl 3 are probed to map charge and energy flow direction and kinetics. Time-resolved photoluminescence and transient absorption measurements reveal charge transfer of photoexcited carriers in MAPbCl 3 to MAPbI 3 in tens of picoseconds. The rate of quenching can be further tuned by replacing MAPbI 3 with two-dimensional Ruddlesden-Popper (BA) 2 (MA) n-1 Pb n I 3 n +1 (n = 3, 2, and 1) perovskites, which also remain phase-separated.

2D perovskites↗