Search NASA⌕ Search

SEARCH · Search NASA

Results for “edge computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

The symmetric turbulent plane wake downstream of a sharp trailing edge

The analysis and modeling of the symmetric turbulent plane wake downstream of a sharp trailing edge is addressed. A compact description of the flow near the trailing edge is formulated using the results of a previous asymptotic analysis. The new description retains the two-layered structure identified in the previous work, and it clarifies the principal dynamics of the flow in the near-wake outer layer, away from the wake centerline. For zero-pressure-gradient flow, the near-wake outer layer is shown to be represented to leading order by the similarity solution that governs the outer region of the surface boundary layer. The leading perturbation in the outer layer due to the developing near-wake inner-layer flow is identified, and this is shown to be asymptotically smaller than undetermined higher-order terms associated with the surface boundary-layer flow. Results of the new near-wake analysis are used to formulate an algebraic eddy viscosity model for wake flow predictions at arbitrary distances from the trailing edge. The model is used in a numerical solution of the boundary layer equations, and computed velocity and Reynolds stress profiles are shown to compare well with experimental data.

Bogucz, E. A.↗

Design of a wing shape for study of hypersonic crossflow transition in flight

Computational fluid dynamics methods were used in the design of a wing shape for study of hypersonic crossflow transition in flight. The flight experiment is to be performed on the delta wing of the first stage of a Pegasus launch vehicle as a piggy-back experiment to support boundary-layer stability code development and validation. The design goal is to obtain crossflow-induced transition at 20-40 percent of the chord for a flight Mach number of approximately six. The present paper describes the design and analysis process utilized to obtain desired glove shape. A variety of schemes were used in the design, ranging from simple empirical crossflow correlations to three-dimensional Navier-Stokes codes in conjunction with linear stability/N-factor computations. The sensitivity to various parameters, such as trajectory variations, allowable wing thickness, leading-edge radius and surface temperature, is also discussed.

Godil, A.↗

Large-deflection theory of curved sheet

Equations are given for the elastic behavior of initially curved sheets in which the deflections are not small in comparison with the thickness, but at the same time small enough to justify the use of simplified formulas for curvature. These equations are solved for the case of a sheet with circular cylindrical shape simply supported along two edges parallel to the axis of the generating cylinder. Numerical results are given for three values of the curvature and for three ratios of buckle length to buckle width. The computations are carried to buckle deflections of about twice the sheet thickness. It was concluded that initial curvature may cause an appreciable increase in the buckling load but that, for edge strains which are several times the buckling strain, the initial curvature causes a negligibly small change in the effective width.

Levy, Samuel↗

Line-vortex theory for calculation of supersonic downwash

The perturbation field induced by a line vortex in a supersonic stream and the downwash behind a supersonic lifting surface are examined to establish approximate methods for determining the downwash behind supersonic wings. Lifting-lines methods are presented for calculating supersonic downwash. A bent lifting-line method is proposed for computing the downwash field behind swept wings. When applied to triangular wings with subsonic leading edges, this method gives results that, in general, are in good agreement with the exact linearized solution. An unbent lifting-line method (horseshoe-vortex system) is proposed for unswept wings. This method is applied to determine downwash behind rectangular wings with aspect ratios of 2 and 4. Excellent agreement with exact linearized theory is obtained for both aspect ratios by placing the lifting line at the 1/2-chord point. The use of lifting-lines therefore appears promising for obtaining estimates of the downwash behind supersonic wings.

Mirels, Harold↗

User's and test case manual for FEMATS

The FEMATS program incorporates first-order edge-based finite elements and vector absorbing boundary conditions into the scattered field formulation for computation of the scattering from three-dimensional geometries. The code has been validated extensively for a large class of geometries containing inhomogeneities and satisfying transition conditions. For geometries that are too large for the workstation environment, the FEMATS code has been optimized to run on various supercomputers. Currently, FEMATS has been configured to run on the HP 9000 workstation, vectorized for the Cray Y-MP, and parallelized to run on the Kendall Square Research (KSR) architecture and the Intel Paragon.

Chatterjee, Arindam↗

A far-field non-reflecting boundary condition for two-dimensional wake flows

Far-field boundary conditions for external flow problems have been developed based upon long-wave perturbations of linearized flow equations about a steady state far field solution. The boundary improves convergence to steady state in single-grid temporal integration schemes using both regular-time-stepping and local-time-stepping. The far-field boundary may be near the trailing edge of the body which significantly reduces the number of grid points, and therefore the computational time, in the numerical calculation. In addition the solution produced is smoother in the far-field than when using extrapolation conditions. The boundary condition maintains the convergence rate to steady state in schemes utilizing multigrid acceleration.

Danowitz, Jeffrey S.↗

Effects of Aircraft Wake Dynamics on Measured and Simulated NO(x) and HO(x) Wake Chemistry

High-resolution numerical large-eddy simulations of the near wake of a B757 including simplified NOx and HOx chemistry were performed to explore the effects of dynamics on chemistry in wakes of ages from a few seconds to several minutes. Dilution plays an important basic role in the NOx-O3 chemistry in the wake, while a more interesting interaction between the chemistry and dynamics occurs for the HOx species. These simulation results are compared with published measurements of OH and HO2 within a B757 wake under cruise conditions in the upper troposphere taken during the Subsonic Aircraft Contrail and Cloud Effects Special Study (SUCCESS) mission in May 1996. The simulation provides a much finer grained representation of the chemistry and dynamics of the early wake than is possible from the 1 s data samples taken in situ. The comparison suggests that the previously reported discrepancy of up to a factor of 20 - 50 between the SUCCESS measurements of the [HO2]/[OH] ratio and that predicted by simplified theoretical computations is due to the combined effects of large mixing rates around the wake plume edges and averaging over volumes containing large species fluctuations. The results demonstrate the feasibility of using three-dimensional unsteady large-eddy simulations with coupled chemistry to study such phenomena.

Lewellen, D. C.↗

CFD Variability for a Civil Transport Aircraft Near Buffet-Onset Conditions

A CFD sensitivity analysis is conducted for an aircraft at several conditions, including flow with substantial separation (buffet onset). The sensitivity is studied using two different Navier-Stokes computer codes, three different turbulence models, and two different grid treatments of the wing trailing edge. This effort is a follow-on to an earlier study of CFD variation over a different aircraft in buffet onset conditions. Similar to the earlier study, the turbulence model is found to have the largest effect, with a variation of 3.8% in lift at the buffet onset angle of attack. Drag and moment variation are 2.9% and 23.6%, respectively. The variations due to code and trailing edge cap grid are smaller than that due to turbulence model. Overall, the combined approximate error band in CFD due to code, turbulence model, and trailing edge treatment at the buffet onset angle of attack are: 4% in lift, 3% in drag, and 31% in moment. The CFD results show similar trends to flight test data, but also exhibit a lift curve break not seen in the data.

Rumsey, Christopher L.↗

A Generalized Multi-Phase Framework for Modeling Cavitation in Cryogenic Fluids

A generalized multi-phase formulation for cavitation in fluids operating at temperatures elevated relative to their critical temperatures is presented. The thermal effects and the accompanying property variations due to phase change are modeled rigorously. Thermal equilibrium is assumed and fluid thermodynamic properties are specified along the saturation line using the NIST-12 databank. Fundamental changes in the physical characteristics of the cavity when thermal effects become pronounced are identified; the cavity becomes more porous, the interface less distinct, and has increased entrainment when temperature variations are present. Quantitative estimates of temperature and pressure depressions in both liquid nitrogen and liquid hydrogen were computed and compared with experimental data of Hord for hydrofoils. Excellent estimates of the leading edge temperature and pressure depression were obtained while the comparisons in the cavity closure region were reasonable. Liquid nitrogen cavities were consistently found to be in thermal equilibrium while liquid hydrogen cavities exhibited small, but distinct, non-equilibrium effects.

Dorney, Dan↗

Research Performed within the Non-Destructive Evaluation Team at NASA Glenn Research Center

Non-destructive testing is essential in many fields of manufacturing and research in order to perform reliable examination of potentially damaged materials and parts without destroying the inherent structure of the materials. Thus, the Non-Destructive Evaluation (NDE) Team at NASA Glenn Research Center partakes in various projects to improve materials testing equipment as well as analyze materials, material defects, and material deficiencies. Due to the array of projects within the NDE Team at this time, five research aims were supplemental to some current projects. A literature survey of "DE and testing methodologies as related to rocks was performed. Also, Mars Expedition Rover technology was assessed to understand the requirements for instrumentation in harsh space environments (e.g. temperature). Potential instrumentation and technologies were also considered and documented. The literature survey provided background and potential sources for a proposal to acquire funding for ultrasonic instrumentation on board a future Mars expedition. The laboratory uses a Santec Systems AcousticScope AS200 acoustography system. Labview code was written within the current program in order to improve the current performance of the acoustography system. A sample of Reinforced Carbon/Carbon (RCC) material from the leading edge of the space shuttle underwent various non-destructive tests (guided wave scanning, thermography, computed tomography, real time x-ray, etc.) in order to characterize its structure and examine possible defects. Guided wave scan data of a ceramic matrix composite (CMC) panel was reanalyzed utilizing image correlations and signal processing variables. Additional guided wave scans and thermography were also performed on the CMC panel. These reevaluated data and images will be used in future presentations and publications. An additional axis for the guided wave scanner was designed, constructed, and implemented. This additional axis allowed incremental spacing of the previously fixed transducers for ultrasonic velocity measurements.

Burns, Erin A.↗

Numerical Strip-Yield Calculation of CTOD

Many existing methods to calculate CTOD can be costly and complicated, or apply only to particular configurations. A new numerical method for calculating CTOD was investigated. NASGRO's Boundary Element module NASBEM was adapted to calculate displacements at any point on the crack. Demonstrated for a number of crack configurations: a) finite and infinite domains; b) center and edge cracks; and c) complex cases with several cracks and holes. Great accuracy at minimal computational cost.

Beek, Joachim↗

Cavity Heating Experiments Supporting Shuttle Columbia Accident Investigation

The two-color thermographic phosphor method has been used to map the local heating augmentation of scaled idealized cavities at conditions simulating the windward surface of the Shuttle Orbiter Columbia during flight STS-107. Two experiments initiated in support of the Columbia Accident Investigation were conducted in the Langley 20-Inch Mach 6 Tunnel. Generally, the first test series evaluated open (length-to-depth less than 10) rectangular cavity geometries proposed as possible damage scenarios resulting from foam and ice impact during launch at several discrete locations on the vehicle windward surface, though some closed (length-to-depth greater than 13) geometries were briefly examined. The second test series was designed to parametrically evaluate heating augmentation in closed rectangular cavities. The tests were conducted under laminar cavity entry conditions over a range of local boundary layer edge-flow parameters typical of re-entry. Cavity design parameters were developed using laminar computational predictions, while the experimental boundary layer state conditions were inferred from the heating measurements. An analysis of the aeroheating caused by cavities allowed exclusion of non-breeching damage from the possible loss scenarios being considered during the investigation.

Everhart, Joel L.↗

Experimental Evaluation of Inlet Distortion on an Ejector Powered Hybrid Wing Body at Take-off and Landing Conditions

As part of the NASA Environmentally Responsible Aircraft project, an ultra high bypass ratio engine integration on a hybrid wing body demonstration was planned. The goal was to include engine and airframe integration concepts that reduced fuel consumption by at least 50% while still reducing noise 42 db cumulative on the ground. Since the engines would be mounted on the upper surface of the aft body of the aircraft, the inlets may be susceptible to vortex ingestion from the wing leading edge at high angles of attack and sideslip, and separated wing/body flow. Consequently, experimental and computational studies were conducted to collect flow surveys useful for characterizing engine operability. The wind tunnel tests were conducted at two NASA facilities, the 14- by 22-foot at NASA Langley and the 40- by 80-foot at NASA Ames Research Center. The test results included in this paper show that the distortion and pressure recovery levels were acceptable for engine operability. The CFD studies conducted to compare to experimental data showed excellent agreement for the angle of attacks examined, although failed to match the low speed experimental data at high sideslip angles.

Carter, Melissa B.↗

Test Cases for a Clipped Delta Wing with Pitching and Trailing-Edge Control Surface Oscillations

Steady and unsteady measured pressures for a Clipped Delta Wing (CDW) undergoing pitching oscillations and trailing-edge control surface oscillations have been presented . From the several hundred compiled data points, 22 static cases, 12 pitching-oscillation cases, and 12 control-surface-oscillation cases have been proposed for Computational Test Cases to illustrate the trends with Mach number, reduced frequency, and angle of attack. The planform for this wing was derived by simplifying the planform of a proposed design for a supersonic transport which is described as the Boeing 2707-300. The strake was deleted, the resulting planform was approximated by a trapezoid with an unswept trailing edge, and the twist and camber were removed. In order to facilitate pressure instrumentation, the thickness was increased to 6 percent from the typical 2.5 to 3 percent for the supersonic transport. The airfoil is thus a symmetrical circular arc section with t/c = 0.06. A wing of similar planform but with a thinner airfoil of t/c = 0.03 was used in the flutter investigations, and the buffet and stall flutter investigation . Flutter results are also reported both for the 3 per cent thick simplified wing and for a more complex SST model. One of the consequences of the increased thickness of the clipped delta wing is that transonic effects are enhanced for Mach numbers near one. They are significantly stronger than would be the case for the thinner wing. Also, with the combination of high leading edge sweep of 50.5, and the sharp leading edge, a leading edge vortex forms on the wing at relatively low angles of attack, on the order of three degrees. The Appendix discusses some of the vortex flow effects. In addition, a shock develops over the aft portion of the wing at transonic speeds such that at some angles of attack, there is both a leading edge vortex and a shock wave on the wing. Such cases are a computational challenge. Some previous applications of this data set have been for the evaluation of an aerodynamic panel method and for evaluation of a Navier-Stokes capability. Linear theory and panel method results are also presented, which demonstrated the need for inclusion of transonic effects. Flutter calculations for the related wing with t/c=O.O3 are given. In this report several Test Cases are selected to illustrate trends for a variety of different conditions with emphasis on transonic flow effects. An overview of the model and tests are given, and the standard formulary for these data is listed. For each type of data, a sample table and a sample plot of the measured pressures are presented. A complete tabulation and plotting of the Test Cases is given. Only the static pressures and the 1st harmonic real and imaginary parts of the pressures are available. All of the data for the test are included in a microfiche document in the original report and are available in electronic file form. The Test Cases are also available as separate electronic files.

Bennett, Robert M.↗

Building a Computational and Experimental Rapid Response Pipeline to Counter the Coronavirus Disease 2019 Outbreak and Emerging Biothreats

The COVID-19 pandemic underscored the promise of monoclonal antibody-based prophylactic and therapeutic drugs, especially where protective candidates can be rapidly identified or developed for emerging biothreats and escape variants. Current cutting-edge technologies for this purpose still rely on pathogen-exposed convalescent volunteers and a large screening effort to find a proverbial needle in a haystack. Computational design of protective antibodies based on pre-existing templates skips those requirements and allows for greater control over the breadth and target epitope, while also co-optimizing for potency and developability or other biophysical characteristics. We approached this problem by building and expanding an in vitro experimental rapid antibody production and characterization pipeline to support development of an autonomous, closed loop, active learning software system based on structural simulation and ground truth experimental data to design and evaluate antibody antigen interactions. Starting from early in the pandemic, we targeted SARS-CoV-2, the causative agent of COVID-19, by re-purposing neutralizing antibodies against SARS-CoV-1 that had been identified in the wake of that outbreak in the early 2000’s. We successfully re-targeted three different anti-SARS-CoV-1 antibodies to neutralize SARS-CoV-2 in vitro, where the antibodies were generated externally and tested through conventional binding and neutralization assays internally or with collaborators. As antibodies were identified from the blood of humans infected with SARS-CoV-2, we shifted to collaborate with academic partners to develop improved versions of their human-derived antibodies. This work reached its most important stage in rapid response to the emergence of the Omicron variant of concern (VOC) in late 2021. In a matter of weeks, enabled by on demand innovation to our screening pipeline, we computationally designed and experimentally characterized derivative antibodies of COV2-2130, one of two antibodies from Vanderbilt that form the basis of the AstraZeneca Evusheld prophylactic drug product. This drug product suffers a serious loss of efficacy against Omicron BA.1 and BA.1.1, the first Omicron strains. Due to tight integration of computational design and experimental evaluation, we were able to identify a pair of designs with potent neutralization of the main targets Omicron BA.1 and BA.1.1; but also the earlier Delta variant, and subsequent Omicron strains including BA.2, BA.4, BA.5, and BA.2.75, demonstrating that our multi-target design process can, by its nature, produce robust antibody designs that strictly improve over the parental antibody. These results, recognized by a 2022 Director’s Science and Technology award, have enabled the follow-on GUIDE program, to commence in FY23. While earlier design campaigns were substantially outsourced, we have engineered better and faster processes internally to better compliment, calibrate, and speed computational designs. As part of the follow-on GUIDE program, we will stand up a rapid and high-throughput antibody production and characterization facility staffed with the expertise and capabilities to foster our current collaboration across PLS and ENG as well as other partnerships toward computational design of biologics.

59 BASIC BIOLOGICAL SCIENCES↗

Modifications to the streamtube curvature program. Volume 1: Program modifications and user's manual

The improvements which have been incorporated in the Streamtube Curvature Program to enhance both its computational and diagnostic capabilities are described. Detailed descriptions are given of the revisions incorporated to more reliably handle the jet stream-external flow interaction at trailing edges. Also presented are the augmented boundary layer procedures and a variety of other program changes relating to program diagnostics and extended solution capabilities. An updated User's Manual, that includes information on the computer program operation, usage, and logical structure, is presented. User documentation includes an outline of the general logical flow of the program and detailed instructions for program usage and operation. From the standpoint of the programmer, the overlay structure is described. The input data, output formats, and diagnostic printouts are covered in detail and illustrated with three typical test cases.

Ferguson, D. R.↗

High-throughput and data-driven search for stable optoelectronic AMSe 3 materials

The rapid advancement in emerging optoelectronic technologies demands highly efficient, affordable, and ecofriendly materials. In this context, ternary chalcogenides, especially ternary selenides, show early promise as a material class due to their stability and remarkable electronic, optical, and transport properties. In this work, we integrate first-principles-based high-throughput computations with machine learning (ML) techniques to predict the thermodynamic stability and optoelectronic properties of 920 valency-satisfied selenide compounds. Through investigating polymorphism, our study reveals the edge-sharing orthorhombic Pnma phase (NH 4 CdCl 3 -type) as the most stable structure for most ternary selenides. High-fidelity supervised ML models are trained and tested to accelerate stability and band gap predictions. These data-driven models pin down the most influential features that dominantly control key material characteristics. The multistep high-throughput computations identify the ternary selenides with optimal direct band gaps, light carrier masses, and strong optical absorption edges. The extensive materials screening considering phase stability, toxicity, and defect tolerance, finally identifies the seven most suitable candidates for photovoltaic applications. Two of these final compounds, SrZrSe 3 and SrHfSe 3 , have already been synthesized in a single-phase form, with the latter showing an optically suitable band gap, aligning well with our findings. The non-adiabatic molecular dynamics reveal sufficiently long photoexcited charge carrier lifetimes (on the order of nanoseconds) in some of these selected selenide materials, indicating their exciting characteristics. Overall, our study suggests a robust in silico framework that can be extended to screen large datasets of various material classes for identifying promising photoactive candidates.

36 MATERIALS SCIENCE↗

Evaluating the Effect of Vane Trailing Edge Flow on Turbine Rim Sealing

Abstract Modern gas turbine development continues to move toward increased overall efficiency, driven in part by higher firing temperatures that point to a need for more cooling air to prevent catastrophic component failure. However, using additional cooling flow bled from the upstream compressor causes a corresponding detriment to overall efficiency. A primary candidate for cooling flow optimization is purge flow, which contributes to sealing the stator–rotor cavity and prevents ingestion of hot main gas path (MGP) flow into the wheelspace. Previous research has identified that the external main gas path flow physics play a significant role in driving rim seal ingestion. However, the potential impact of other cooling flow features on ingestion behavior, such as vane trailing edge (VTE) flow, is absent in the open literature. This paper presents experimental measurements of rim cavity cooling effectiveness collected from a one-stage turbine operating at engine-representative Reynolds and Mach numbers. Carbon dioxide (CO2) was used as a tracer gas in both the purge flow and vane trailing edge flow to investigate flow migration into and out of the wheelspace. Results show that the vane trailing edge flow does in fact migrate into the rim seal and that there is a superposition relationship between individual cooling flow contributions. Computational fluid dynamics (CFD) simulations using unsteady Reynolds-averaged Navier–Stokes (URANS) were used to confirm VTE flow ingestion into the rim seal cavity. Radial and circumferential traverse surveys were performed to quantify cooling flow radial migration through the main gas path with and without vane trailing edge flow. The surveys confirmed that vane trailing edge flow is entrained into the wheelspace as purge flow is reduced. Local CO2 measurements also confirmed the presence of VTE flow deep in the wheelspace cavity.

Engineering↗