Search NASA⌕ Search

SEARCH · Search NASA

Results for “high loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Hexagonal Distributed Embedded Energy Converters (HexDEECs)

Distributed Embedded Energy Converter Technologies (DEEC-Tec) is a new domain for marine renewable energy research that utilizes a conglomeration of small distributed embedded energy converters (DEECs) that, in aggregate, form larger metamaterial frameworks. These resulting DEEC-Tec metamaterials can then, in turn, be used to construct flexible ocean wave energy converters called flexWECs. DEEC-Tec enables flexWECs: (i) to be inherently broad-banded ocean wave frequency energy converters and (ii) to have an inherent lack of highly loaded rigid bodies. The DEEC-Tec domain also benefits the marine renewable energy domain by inherently availing ways that marine energy can be harvested and converted that heretofore has not yet been considered possible: real-time execution of transforming topologies (e.g., actively changing a flexWEC's shape and form) and morphologies (e.g., actively changing a flexWEC's stiffness and damping throughout its entire structure). Presented, is one specific type of DEEC, a HexDEEC, that shows promise in aiding the adoption and further development of the DEEC-Tec domain - it is a small energy transducer being developed by the United States National Renewable Energy Laboratory. The HexDEEC is a small (characteristic length approximating a centimeter) energy transducer that converts the dynamic deformations of an elastomer into electricity through a charging-discharging cycle of a capacitor whose capacitance is varied by those elastic deformations. The HexDEEC is composed of a hyperelastic hexagonal housing (nominally silicon rubber) with six electrodes on its inner faces. The upper three electrodes share the same charge while the lower three electrodes oppose the upper electrode charges. Externally, the HexDEEC has two arms extending away from the middle vertices of the hexagon. Via principles governing the relationship between electrical capacitance and electrical potential (voltage and charge), electricity is generated when the HexDEEC's arms are dynamically pulled or released under tensile loading as doing so causes the distance between the upper and lower sets of electrodes to change - varying the energy converter's overall capacitance. Analytical and numerical modeling have already been used to estimate the electrical energy produced by a HexDEEC. The cursory models approximate the HexDEEC as a parallel plate variable capacitor - simplifying from six to two opposing plates with a constant dielectric volume between those two plates. To account for the elastic HexDEEC material properties, software such as SolidWorks and STAR-CCM+ have been used to generate hyperelastic models; notably, Mooney-Rivlin based models. Individual HexDEECs have been fabricated by drawing uncured liquid silicon rubber into molds via vacuum pressure. To simplify manufacturing, HexDEEC sub-components - e.g., electrodes, wires - can be placed within those molds such that they are directly embedded into the hexagonal housing during the curing process. Furthermore, DEEC-Tec metamaterials can be created by interweaving or sequentially layering multiple HexDEEC strands together. The HexDEEC based metamaterial could then generate electricity through its gross deformations. Ultimately, HexDEECs represent a specific type of energy transducer that can be leveraged, by the DEEC-Tec domain, to create metamaterials used to construct novel flexWECs.

DEEC-Tec↗

Low friction coatings

A low friction, wear-resistant surface operable at high temperatures and high loads with a low coefficient of friction including boron nitride and graphene-oxide on steel or nanodiamonds and graphene on aluminum. The low friction, wear-resistant surface remains with a coefficient of friction in the superlubric regime at temperatures in between about 200° C. and 970° C.

36 MATERIALS SCIENCE↗

Investigating Marine Environmental Degradation of Additive Manufacturing Materials for Renewable Energy Applications

Marine renewable energy is a relatively young industry where there is a great need for rapid prototyping in design-build-test campaigns to quickly mature groundbreaking technologies. Additive manufacturing has an important role to play in the industry; however, little information is available to marine energy developers to help inform them on which additive manufacturing materials are appropriate for highly loaded structures in harsh marine environments. This paper presents an initial study on the mechanical characterization of polymeric additive manufacturing materials and the degradation effects due to the marine environment. Ultem 9085, acrylonitrile styrene acrylate, and chopped carbon-filled nylon, as well as continuous carbon and glass fiber-reinforced nylon were chosen for this study. Samples were manufactured to perform a variety of tension, shear, and compression mechanical characterization tests on the materials. Half of the samples were conditioned in Pacific Ocean water for approximately 6 months at the Pacific Northwest National Laboratory's Marine and Coastal Research Laboratory before being returned for mechanical characterization. The mechanical testing results showed that the Ultem 9085 and acrylonitrile styrene acrylate materials experienced little to no degradation in stiffness or strength after exposure to the marine environment. On the other hand, the nylon-based materials suffered significant stiffness and strength degradation (over 50% in some cases) after environmental conditioning. Ultimately, these data sets should serve as starting points to allow marine renewable energy developers to make informed additive manufacturing material choices for their prototype deployments.

additive manufacturing↗

A practical solution to Hanford's tank waste problem

The main characteristics of the Hanford radwaste are: -) it is extremely dilute and generates little heat, -) it is comprised of materials incompatible with high loading in borosilicate glass, and -) it is already situated at a good geological repository site. We propose that Hanford's radwaste should be homogenized (not separated), converted to an iron phosphate (Fe-P) glass 'aggregate' (marbles, gems, or cullet), that is then slurried up with a cementitious grout and pumped into Hanford's 'best preserved' tanks for disposal. This proposal is efficient, safe and cheap.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Robust Power Remote Manipulator for Use in Waste Sorting, Processing, and Packaging - 12158

Disposition of radioactive waste is one of the Department of Energy's (DOE's) highest priorities. A critical component of the waste disposition strategy is shipment of Transuranic (TRU) waste from DOE's Oak Ridge Reservation to the Waste Isolation Plant Project (WIPP) in Carlsbad, New Mexico. This is the mission of the DOE TRU Waste Processing Center (TWPC). The remote-handled TRU waste at the Oak Ridge Reservation is currently in a mixed waste form that must be repackaged in to meet WIPP Waste Acceptance Criteria (WAC). Because this remote-handled legacy waste is very diverse, sorting, size reducing, and packaging will require equipment flexibility and strength that is not possible with standard master-slave manipulators. To perform the wide range of tasks necessary with such diverse, highly contaminated material, TWPC worked with S.A. Technology (SAT) to modify SAT's Power Remote Manipulator (PRM) technology to provide the processing center with an added degree of dexterity and high load handling capability inside its shielded cells. TWPC and SAT incorporated innovative technologies into the PRM design to better suit the operations required at TWPC, and to increase the overall capability of the PRM system. Improving on an already proven PRM system will ensure that TWPC gains the capabilities necessary to efficiently complete its TRU waste disposition mission. The collaborative effort between TWPC and S.A. Technology has yielded an extremely capable and robust solution to perform the wide range of tasks necessary to repackage TRU waste containers at TWPC. Incorporating innovative technologies into a proven manipulator system, these PRMs are expected to be an important addition to the capabilities available to shielded cell operators. The PRMs provide operators with the ability to reach anywhere in the cell, lift heavy objects, perform size reduction associated with the disposition of noncompliant waste. Factory acceptance testing of the TWPC Powered Remote Manipulators has completed at SAT's Colorado facility, and on-site training at TWPC is scheduled to start in early 2012. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Improving actinides recycling, a key step towards a more sustainable nuclear energy - 15617

Nuclear energy is thought to be one of the energy sources that could help mitigating the global climate change together with the renewables, due to its low green-house-gases emissions, its reliability and its high load power. However, nuclear energy will only develop if future nuclear energy systems meet the criteria of sustainability in terms of durability, bearability and liveability. Nowadays, many countries chose the so-called once-through cycle which basically considers spent nuclear fuel as a waste, whereas others reprocess their spent fuel to recover the energetically-valuable material Pu (and partially U) to produce Mixed Oxide Fuel (MOX) to be irradiated in a second cycle (twice-through cycle). Both options can be considered relevant, fitting diverse criteria; but if we consider a long lasting prospective for nuclear options, the once-through cycle sustainability is clearly lower (low consumption of natural resource, no recycling of potentially valuable energetic material, larger volume of waste...). Reversely, twice-through cycle can be seen as a first step towards an improved sustainability with a partial recycling of U/Pu and the reduction of the waste volume and toxicity. However, it is likely not sufficient for the long-term and implementing more efficient recycling is a key-driver to improve the environmental friendship, the economics and the social acceptability of nuclear energy. Future nuclear fuel cycles will have to better preserve the natural resource by improving the actinides recycling, to minimize the volume and toxicity of nuclear waste, to ensure their long-term confinement and to prevent any proliferation-risk. Such a gradual and progressive process calls for implementing appropriate technologies, either for reactors but also for fuel treatment/recycling facilities. This paper will describe the successive step that would allow improving the overall sustainability. Indeed, recycled Pu can be once recycled in MOX fuel feeding similar PWRs (Pressurized Water Reactor). Together with the recycling of reprocessed uranium, this first step already allows preserving ∼17% of the natural U resource and to confine ultimate wastes without Pu in a tailored durable wasteform. Subsequent Pu multi-recycling requires introducing Fast Reactors (FR) to efficiently use U-238 available in natural and depleted uranium stockpiles. In parallel, recycling processes would have to be adapted for treating spent LWR and SFR MOX spent fuels, which is currently under study thanks to an ambitious R and D program dedicated on MOX treatment and recycling. For the longer term, minor actinides recycling would allow decreasing the waste burden towards future generations: (i) Am-recycling leads to decrease the waste residual heat-power and increase the repository density and lifespan, (ii) Cm-recycling leads to decrease waste long-term toxicity. The stepwise implementation of these different processes defines a path towards sustainability for nuclear energy that are described in this paper from the fuel cycle viewpoint. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Behaviour of Alpha Emitters in Cement - 16139

Alpha emitting radioelements can interact with cements in a number of ways. Alpha-radiolysis of water produces hydrogen that may pressurise and damage the structure, and it is postulated that the intense alpha radiation field around waste particles containing high alpha activity can cause mineralogical changes in the hydration products. In addition, their solubility in cement pore fluid can be increased by complexation with organic materials such as the degradation products of cellulose, which itself may be promoted by alpha irradiation. Analysis of pore fluid expressed from cements containing plutonium and a range of organic materials has demonstrated their effect on plutonium solubility. Calculations of hydrogen pressurisation as a result of alpha radiolysis suggest that radiolytic hydrogen will not exceed tensile strength of the cement. Further work is described in which cements containing high loadings of plutonium will be examined in the NNL Central Laboratory to investigate mineralogical changes during and after hydration. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Water and Ammonia Desorption from 5A Zeolite

Demonstrate adsorption and desorption characteristics of water and ammonia on 5A zeolite during regeneration conditions using a Thermogravimetric analyzer (TGA) on samples previously evaluated by residual gas analyzer (RGA)/mass balance. Molecular sieve (zeolite) adsorbents have the following characteristics: Crystalline alumino-silicates containing pores or 'cages' that adsorb water or other molecules. Polar compound are adsorbed with high loading even at very low concentrations of the fluid. A 5A molecular sieve was chosen for its ability to adsorb both water and ammonia (NH{sub 3}) from a carrier gas stream. Preliminary RGA/mass balance testing indicated: 5A zeolite captured both NH{sub 3} and water as anticipated based on molecular size; Reloading showed limited success after zeolite heated beyond manufacturer recommended operating conditions: Steam dealumination theorized cause; Tests were reprioritized to focus on NH{sub 3} removal and end of life potential holdup of NH{sub 3} and water on 5A zeolite material. TGA measures a sample's weight and volatile composition as it is heated or cooled in a furnace. TGA heats sample to release volatile materials, (change in mass is measured). MS detects/measures low levels of impurities. Perform TGA desorption of zeolite samples taken at the following conditions tested with RGA (RGA results not shown here): Initial Bakeout conditions: hydrogen carrier gas, slowly raise temp to approximately 300 deg. C until desired moisture content <<100 ppm is achieved. Water loading (re-loading): argon carrier gas through bubbler until breach is observed. Ammonia loading (re-loading): hydrogen carrier gas through system. Regenerations/End of life conditions: hydrogen carrier gas, raise temp to approximately 300 deg. C, then slowly to 450 deg. C (end of life). After end of life testing less than 4% of the total mass was residual ammonia or water at bakeout conditions. Peak water and ammonia removal occurred around 275 deg. C and 150 deg. C respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanocellulose as an embedding matrix and applications thereof

A versatile drug delivery system comprised of plant-based nanocellulose can be used for providing high loading and extended release for virtually any drug. This system is made from nanocrystalline cellulose chemically cross-linked to form a hydrogel. This versatile hydrogel-based drug delivery system can be functionalized to support extended release of oral dosing, relieving patient burden and increasing quality of life.

Ray, Anamika↗

Nanomaterials-Enhanced Electrically Switched Ion Exchange Process for Water Treatment

The objective of our work is to develop an electrically switched ion exchange (ESIX) system based on conducting polymer/carbon nanotube (CNT) nanocomposites as a new and cost-effective approach for removal of radioactive cesium, chromate, and perchlorate from contaminated groundwater. The ESIX technology combines ion exchange and electrochemistry to provide a selective, reversible method for the removal of target species from wastewater. In this technique, an electroactive ion exchange layer is deposited on a conducting substrate, and ion uptake and elution are controlled directly by modulation of the potential of the layer. ESIX offers the advantages of highly-efficient use of electrical energy combined with no secondary waste generation. Recently, we have improved upon the ESIX process by modifying the conducting substrate with carbon nanotubes prior to the deposition of the electroactive ion exchanger. The nanomaterial-based electroactive ion exchange technology will remove cesium-137, chromate, and perchlorate rapidly from wastewater. The high porosity and high surface area of the electroactive ion exchange nanocomposites results in high loading capacity and minimize interferences for non-target species. Since the ion adsorption/desorption is controlled electrically without generating a secondary waste, this electrically active ion exchange process is a green process technology that will greatly reduce operating costs.

54 ENVIRONMENTAL SCIENCES↗

Considerations of Alloy 617 Application in the Gen IV Nuclear Reactor Systems - Part I: Mechanical Property Challenges

Alloy 617 is currently considered as a leading candidate material for high temperature components in the Gen IV Nuclear Reactor Systems. Because of the unprecedented severe working conditions beyond its commercial service experience required by the Gen IV systems, the alloy faces various challenges in both mechanical and metallurgical properties. This paper, as Part I of the discussion, is focused on the challenges and issues in the mechanical properties of Alloy 617 for the intended nuclear application. Considerations are given in details in its mechanical property data scatter, low creep strength in the desired high temperature range, lack of longterm creep curves, high loading rate dependency, and preponderant tertiary creep. Some research and development activities are suggested with discussions on their viability to satisfy the Gen IV Nuclear Reactor System needs in near future and in the long run.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Investigating potential efficiency improvement for light-duty transportation applications through simulation of an organic Rankine cycle for waste-heat recovery

Modern diesel engines used in light-duty transportation applications have peak brake thermal efficiencies in the range of 40-42% for high-load operation with substantially lower efficiencies at realistic road-load conditions. Thermodynamic energy and exergy analysis reveals that the largest losses from these engines are due to heat loss and combustion irreversibility. Substantial improvement in overall engine efficiency requires reducing or recovering these losses. Unfortunately, much of the heat transfer either occurs at relatively low temperatures resulting in large entropy generation (such as in the air-charge cooler), is transferred to low-exergy flow streams (such as the oil and engine coolant), or is radiated or convected directly to the environment. While there are significant opportunities for recovery from the exhaust and EGR cooler for heavy-duty applications, the potential benefits of such a strategy for light-duty applications are unknown due to transient operation, low-load operation at typical driving conditions, and the added mass of the system. We have developed an organic Rankine cycle model using GT-Suite to investigate the potential for efficiency improvement through waste-heat recovery from the exhaust and EGR cooler of a light-duty diesel engine. Results from steady-state and drive-cycle simulations are presented, and we discuss strategies to address operational difficulties associated with transient drive cycles and competition between waste-heat recovery systems, turbochargers, aftertreatment devices, and other systems for the limited thermal resources.

33 ADVANCED PROPULSION SYSTEMS↗

VRN3P: Variational Recurrent Neural Network Based Net-Load Prediction under High Solar Penetration

This is the final technical report for the SETO-funded VRN3P project (PNNL# 76914). The goal of this project, led by Pacific Northwest National Laboratory (PNNL), in collaboration with Lawrence Livermore National Laboratory (LLNL) and Portland General Electric (PGE), was to develop and validate a deep variational recurrent neural network-based net-load prediction (VRN3P) framework for probabilistic time-series forecasting of day-ahead net-load under high solar penetration scenarios. The project team reports successful design of a novel probabilistic net-load forecasting architecture, comprising of a variational autoencoder and a recurrent neural network, which demonstrates 30% improvement in forecast performance, 60% improvement in training time, and consumes 44% less memory, when compared with conventional baseline models. The team tested the VRN3P model performance on GridLAB-D test-cases representing varying BTM solar penetration levels of 20%, 30%, and 50%, with integrated time-series net-load profiles provided by the utility partner (PGE). The VRN3P model demonstrate <2% hourly MAPE (averaged over the year) for day- ahead net-load forecast on the test scenario with 20% BTM solar. Transfer learning extension of the VRN3P model has demonstrated 8.33× speed-up in training, while still achieving acceptable forecast performance of 2.24% hourly MAPE on the 30% BTM solar penetration test-scenario. A preliminary version of the VRN3P GridAPPS-D™has been developed, along with a web-based interactive user-interface (named ‘Forte’) which has made available on GitHub for public use.

24 POWER TRANSMISSION AND DISTRIBUTION↗

High Dielectric Dummy Loads for ITER ICRH Antenna Laboratory Testing: Numerical Simulation of One Triplet Loading by Ferroelectric Ceramics

Up to now, classical 'water' loads have been used for low power testing of ITER ICRH prototype or mock-up antennas . A fair description of the antenna frequency response is obtained excepted for the phasing (0 {pi} 0 {pi}). High dielectric loads are requested to improve the antenna response in the low frequency band. In view of laboratory testing, dummy loads are also required to have efficient wave spatial attenuation to avoid standing waves and to minimize load volume. In this paper, barium titanate ceramic powders mixed with water are shown to exhibit very attractive electromagnetic properties. Coupling performance of one triplet of the ITER ICRH antenna to such kind of loads is numerically investigated. The radiated wave attenuation into the load is also characterized. In spite of its frequency dispersion, 'barium titanate' loads are shown to allow the characterization of the full scale triplet frequency response on a scaled-down mock-up.

36 MATERIALS SCIENCE↗

Equation of state and strength of diamond in high-pressure ramp loading

Diamond is used extensively as a component in high-energy-density experiments, but existing equation of state (EOS) models do not capture its observed response to dynamic loading. In particular, in contrast with first-principles theoretical models of equilibrium multiphase EOS, no solid-solid phase changes have been detected, and no general-purpose EOS models match the measured ambient isotherm. We have performed density functional theory (DFT) calculations of the diamond phase to ~10 TPa, well beyond its predicted range of thermodynamic stability, and used these results as the basis of a Mie-Grüneisen EOS. We also performed DFT calculations of the elastic moduli, and calibrated an algebraic elasticity model for use in simulations. We then estimated the flow stress of diamond by comparison with the stress-density relation measured experimentally in ramp-loading experiments. Furthermore, the resulting constitutive model allows us to place a constraint on the Taylor-Quinney factor (the fraction of plastic work converted to heat) from the observation that diamond does not melt on ramp compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High solids co-digestion of food and landscape waste and the potential for ammonia toxicity

Highlights: • We evaluated co-digestion of food and landscape waste with a pilot-scale anaerobic dry digester. • We evaluated reactor performance at 35 °C under low and high organic loading rates. • Performance was stable under low organic loading rate, but declined under high organic loading rate. • Respirometry was employed to investigate potential inhibition due to ammonia. • Landscape waste was unsuitable in increasing the C:N ratio during codigestion. - Abstract: A pilot-scale study was completed to determine the feasibility of high-solids anaerobic digestion (HSAD) of a mixture of food and landscape wastes at a university in central Pennsylvania (USA). HSAD was stable at low loadings (2 g COD/L-day), but developed inhibitory ammonia concentrations at high loadings (15 g COD/L-day). At low loadings, methane yields were 232 L CH{sub 4}/kg COD fed and 229 L CH{sub 4}/kg VS fed, and at high loadings yields were 211 L CH{sub 4}/kg COD fed and 272 L CH{sub 4}/kg VS fed. Based on characterization and biodegradability studies, food waste appears to be a good candidate for HSAD at low organic loading rates; however, the development of ammonia inhibition at high loading rates suggests that the C:N ratio is too low for use as a single substrate. The relatively low biodegradability of landscape waste as reported herein made it an unsuitable substrate to increase the C:N ratio. Codigestion of food waste with a substrate high in bioavailable carbon is recommended to increase the C:N ratio sufficiently to allow HSAD at loading rates of 15 g COD/L-day.

54 ENVIRONMENTAL SCIENCES↗

Numerical Analysis of Fatigue Behavior of ITER-Like Monoblock Divertor Interlayer Under Coupled Heat Loads

High-confinement mode is a very prominent operation style for future fusion device due to its unique advantages. However, the conjuncted edge localized modes (ELMs) are very difficult to control so that divertor plates are very prone to suffer both stationary high heat flux (HHF) loads of long-pulse operating mode and transient shock loads of ELMs. Most previous researches focus on degradation of plasma facing material (PFM), however, as a layer joining PFM and cooling tube, the soft copper interlayer suffers concentrated thermal stress loads due to mismatched thermal expansion of PFM and cooling tube. Its thermal fatigue behavior under such coupled loads is also of great significance to structural safety of divertor component. With such a motivation, the reduction effects on fatigue life time of a typical interlayer of monoblock divertor under series of coupled HHF and ELMs shock loading conditions are investigated. It is found that: (1) The transient shock feature of ELMs loading is propagated into interlayer with less sharp pattern. The increase of damage induced by coupled ELMs loading is limited in single cycle, while the accumulated damage of multiple consecutive coupled loading cycles is increased nonlinearly. (2) Under the coupled HHF and ELMs loading, the fatigue life time of interlayer is generally decreasing. The magnitude of decrease is increasing nonlinearly with the magnitude of ELMs peak and averaged heat flux. (3) For three characteristic parameters of ELMs shock loading such as frequency, duration and peak heat flux, the peak heat flux and frequency are two parameters more sensitive to determine coupled reduction effects on fatigue lifetime of the interlayer, while for high frequency case, time averaged heat flux takes the lead.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaluation of space shuttle main engine bearings from high pressure oxygen turbopump 9008

Two used turbopump mainshaft support bearings were examined to determine steps needed to achieve turbopump lifetimes of 27,000 seconds. The two bearings, which had been run in a high pressure oxygen turbopump, are angular contact ball bearings, applied as a preloaded pair, locked to the shaft, inner race rotating, with the outer races unrestrained axially. Examination showed that both bearings had been subjected to overloads, leading to fatigue spalling on the races and balls and advanced retainer wear. This is clear evidence of unintended high internal loads in the high pressure oxygen pump which would lead to complete bearing failure and extensive secondary pump damage. Action must be taken to reduce the applied bearing loads or to incorporate bearings of sufficient size to withstand the high loads.

Dufrane, K. F.↗