Search NASA⌕ Search

SEARCH · Search NASA

Results for “load shape”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Effect of individual blade control on noise radiation

In a joint research program of NASA Ames Research Center, ZF Luftfahrttechnik, the German Aerospace Research Establishment (DLR), and EUROCOPTER Deutschland, a wind tunnel test was performed to evaluate the effects of Individual Blade Control (IBC) on rotor noise. This test was conducted in the 40x80 ft wind tunnel at NASA Ames Research Center, utilizing a full scale MBB-BO 105 four-bladed rotor system. Three microphones were installed for determination of the radiated noise, two of them on a moveable traverse below the advancing blade side and one in a fixed location below the retreating side. Acoustic results are presented for flight conditions with Blade-Vortex-Interaction (BVI) noise radiation. High noise level reductions were measured for single harmonic control inputs. In addition to the single harmonic inputs, multi-harmonic inputs were evaluated by superimposing 2/rev to 6/rev harmonics. For the first time the efficiency of sharp wavelets (60 deg and 90 deg width) on acoustic noise were measured. In order to achieve an adequate wavelet shape at the blade tip, corrections were made to account for the blade torsional behavior. In parallel with the acoustic measurements, vibratory loads were measured during the BVI flight condition to correlate the effects of IBC on noise and vibrations. It is shown how noise levels and vibrations are affected by specific IBC control inputs. In addition, correlations are made between noise levels and acoustic time histories with IBC phase and amplitude variations. For one IBC input mode with high noise reducing efficiency, a sweep of the moveable microphone traverse below the advancing side shows the effect on BVI noise directivity.

Swanson, S. M.↗

Design Evaluation Using Finite Element Analysis of Cooled Silicon Nitride Plates for a Turbine Blade Application

Two- and three-dimensional finite element analyses were performed on uncoated and thermal barrier coated (TBC) silicon nitride plates with and without internal cooling by air. Steady-state heat-transfer analyses were done to optimize the size and the geometry of the cooling channels to reduce thermal stresses, and to evaluate the thermal environment experienced by the plate during burner rig testing. The limited experimental data available were used to model the thermal profile exerted by the flame on the plate. Thermal stress analyses were performed to assess the stress response due to thermal loading. Contours for the temperature and the representative stresses for the plates were generated and presented for different cooling hole sizes and shapes. Analysis indicates that the TBC experienced higher stresses, and the temperature gradient was much reduced when the plate was internally cooled by air. The advantages and disadvantages of several cooling channel layouts were evaluated.

Abdul-Aziz, Ali↗

ORTHOPEDIC LEG BRACE

Knee braces generally have been rigid in both the knee bending direction and in the knee straightening direction unless a manually operated release is incorporated in them to allow the knee to bend. Desirably a braced knee joint should effectively duplicate the compound, complex, actions of a normal knee. The key to knee braces is the knee joint housing. The housing herein carries a number of cam action pawls. with teeth adapted to engage the internal teeth of a ratchet ring mounted in the housing. Cam action return springs and the shape of the cam action pawl teeth allow rotation of the ratchet ring in a leg straightening direction while still supporting a load. The leg can then be extended during walking while at the same time being prevented by the cam action pawls from buckling in the knee bending direction.

Myers, William Neil↗

Energy-Absorbing, Lightweight Wheels

Improved energy-absorbing wheels are under development for use on special-purpose vehicles that must traverse rough terrain under conditions (e.g., extreme cold) in which rubber pneumatic tires would fail. The designs of these wheels differ from those of prior non-pneumatic energy-absorbing wheels in ways that result in lighter weights and more effective reduction of stresses generated by ground/wheel contact forces. These wheels could be made of metals and/or composite materials to withstand the expected extreme operating conditions. As shown in the figure, a wheel according to this concept would include an isogrid tire connected to a hub via spring rods. The isogrid tire would be a stiff, lightweight structure typically made of aluminum. The isogrid aspect of the structure would both impart stiffness and act as a traction surface. The hub would be a thin-walled body of revolution having a simple or compound conical or other shape chosen for structural efficiency. The spring rods would absorb energy and partially isolate the hub and the supported vehicle from impact loads. The general spring-rod configuration shown in the figure was chosen because it would distribute contact and impact loads nearly evenly around the periphery of the hub, thereby helping to protect the hub against damage that would otherwise be caused by large loads concentrated onto small portions of the hub.

Waydo, Peter↗

RST Optical Telescope Integration and Test Preparation

The OTA for the Nancy Grace Roman Space Telescope includes the primary mirror, secondary mirror, and aft optics for guiding light into the Wide Field Instrument and the Coronagraph Instrument. The telescope is taking shape as the tested optical mirror assemblies are integrated. The assemblies have been thermal cycled to the cold temperatures for infrared operation, load tested to launch loads, vibration tested, and optically tested. Testing included launch-level vibration testing of the 2.4-meter light-weighted primary mirror assembly. In addition, the telescope control electronics (TCE) box has been fully assembled and the environmental testing of the TCE is progressing. Pictures and descriptions of the integration and test progress are provided, along with performance results measured at these levels of assemblies. Planning and test equipment preparation for the telescope thermal vacuum testing continues including plans to take advantage of the large dynamic range available with focus diversity phase retrieval and a Shack-Hartmann wavefront sensor for the gravity-sagged primary mirror.

Tony L Whitman↗

Autonomous Energy Grids: Preprint

With much higher levels of distributed energy resources - variable generation, energy storage, and controllable loads just to mention a few - being deployed into power systems, the data deluge from pervasive metering of energy grids, and the shaping of multi-level ancillary-service markets, current frameworks to monitoring, controlling, and optimizing large-scale energy systems are becoming increasingly inadequate. This position paper outlines the concept of 'Autonomous Energy Grids' (AEGs) - systems that are supported by a scalable, reconfigurable, and self-organizing information and control infrastructure, can be extremely secure and resilient (self-healing), and self-optimize themselves in real-time for economic and reliable performance while systematically integrating energy in all forms. AEGs rely on scalable, self-configuring cellular building blocks that ensure that each 'cell' can self-optimize when isolated from a larger grid as well as partaking in the optimal operation of a larger grid when interconnected. To realize this vision, this paper describes the concepts and key research directions in the broad domains of optimization theory, control theory, big-data analytics, and complex system modeling that will be necessary to realize the AEG vision.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Solid-State Ultracapacitor Polymer Composite

An ultracapacitor made from a polymer loaded with ceramic powder would have several advantages over current ultracapacitors and batteries. First is the possibility of it being printable, which would allow for printing the energy storage device along with the circuit instead of having to find a way to add one later without damaging the rest of the components. When not printed in a specific design for use on a printed wiring board, this type of ultracapacitor could still be cured via a mold to a shape suitable to specific applications. Many polymers maintain some flexibility even after curing, such as the silicone used in this study. The manufacturing process would also be far simpler than that of conventional ultracapacitors.In this work, solid-state ultracapacitors were made by adding the dielectric powder to a two-part polymer (resin and hardener) at the same time. The mixture was then cured in the desired shape at a low temperature until completely set. The addition of the powder to the polymer increased its dielectric properties while leaving most of its physical properties unaltered. At higher powder loading percentages, there were some physical changes as the maximum loading point was approached. To determine the efficiency of these solid-state ultracapacitors, their capacitances were tested, and their dielectric constants (DCs) were measured and compared.

energy storage↗

Modification of turbulent boundary layer structure by large-eddy breakup devices

The modification of the turbulent boundary layer large-eddy structure by streamlined devices is analyzed using the rapid distortion approximation and unsteady aerodynamic theory. The fluctuating velocity downstream of thin plate and airfoil-shaped devices is calculated throughout the boundary layer for two-dimensional and three-dimensional upstream harmonic disturbances. It is shown that such devices suppress most effectively the fluctuating vertical velocity for a range of reduced frequencies k(1) based on the device chord length. This effect depends on the device geometry and loading, its distance to the wall, and on the upstream disturbance condition. Effective devices suppressing most of the large-scale turbulent energy are such that k(1) varies over the 0.5 to 3.0 range. For airfoil-shaped devices, the device thickness has minimal effect on its performance. On the other hand, lifting devices are more effective than thin plates particularly for two-dimensional disturbances.

Atassi, H. M.↗

Transformation behavior and shape memory characteristics of thermo-mechanically treated Ti–(45−x)Ni–5Cu–xV (at%) alloys

Transformation behavior, shape memory characteristics and superelasticity of thermo-mechanically treated Ti–(45−x)Ni–5Cu–xV (at%) (x = 0.5–2.0) alloys were investigated by means of differential scanning calorimetry, transmission electron microscopy, X-ray diffractions, thermal cycling tests under constant load and tensile tests. The B2–B19′ transformation occurred when V content was 0.5 at%, above which the B2–B19–B19′ transformation occurred. The B2–B19 transformation was not separated clearly from the B19–B19′ transformation. Thermo-mechanically treated Ti–(45−x)Ni–5Cu–xV alloys showed perfect shape memory effect and transformation hysteresis(ΔT) of Ti–43.5Ni–5.0Cu–1.5V and Ti–43.0Ni–5.0Cu–2.0V alloys was about 9 K which was much smaller than that of a Ti–44.5Ni–5.0Cu–0.5V alloy(23.3 K). More than 90% of superelastic recovery ratio was observed in all specimens and transformation hysteresis (Δσ) of a Ti–44.5Ni–5.0Cu–0.5V alloy was about 70 MPa, which was much larger than that of a Ti–43.0Ni–5.0Cu–2.0V alloy (35 MPa).

36 MATERIALS SCIENCE↗

Multi-Objective Flight Control for Drag Minimization and Load Alleviation of High-Aspect Ratio Flexible Wing Aircraft

As aircraft wings become much more flexible due to the use of light-weight composites material, adverse aerodynamics at off-design performance can result from changes in wing shapes due to aeroelastic deflections. Increased drag, hence increased fuel burn, is a potential consequence. Without means for aeroelastic compensation, the benefit of weight reduction from the use of light-weight material could be offset by less optimal aerodynamic performance at off-design flight conditions. Performance Adaptive Aeroelastic Wing (PAAW) technology can potentially address these technical challenges for future flexible wing transports. PAAW technology leverages multi-disciplinary solutions to maximize the aerodynamic performance payoff of future adaptive wing design, while addressing simultaneously operational constraints that can prevent the optimal aerodynamic performance from being realized. These operational constraints include reduced flutter margins, increased airframe responses to gust and maneuver loads, pilot handling qualities, and ride qualities. All of these constraints while seeking the optimal aerodynamic performance present themselves as a multi-objective flight control problem. The paper presents a multi-objective flight control approach based on a drag-cognizant optimal control method. A concept of virtual control, which was previously introduced, is implemented to address the pair-wise flap motion constraints imposed by the elastomer material. This method is shown to be able to satisfy the constraints. Real-time drag minimization control is considered to be an important consideration for PAAW technology. Drag minimization control has many technical challenges such as sensing and control. An initial outline of a real-time drag minimization control has already been developed and will be further investigated in the future. A simulation study of a multi-objective flight control for a flight path angle command with aeroelastic mode suppression and drag minimization demonstrates the effectiveness of the proposed solution. In-flight structural loads are also an important consideration. As wing flexibility increases, maneuver load and gust load responses can be significant and therefore can pose safety and flight control concerns. In this paper, we will extend the multi-objective flight control framework to include load alleviation control. The study will focus initially on maneuver load minimization control, and then subsequently will address gust load alleviation control in future work.

Aerolasticity↗

Weaving multi-layer fabrics for reinforcement of engineering components

The performance of interlinked, multi-layer fabrics and near net shape preforms for engineering applications, woven on a 48 shaft dobby loom using glass, aramid, and carbon continuous filament yarns is assessed. The interlinking was formed using the warp yarns. Two basic types of structure were used. The first used a single warp beam and hence each of the warp yarns followed a similar path to form four layer interlinked reinforcements and preforms. In the second two warp beams were used, one for the interlinking yarns which pass from the top to the bottom layer through-the-thickness of the fabric and vice versa, and the other to provide 'straight' yarns in the body of the structure to carry the axial loading. Fabrics up to 15mm in thickness were constructed with varying amounts of through-the-thickness reinforcement. Tapered T and I sections were also woven, with the shaping produced by progressive removal of ends during construction. These fabrics and preforms were impregnated with resin and cured to form composite samples for testing. Using these two basic types of construction, the influence of reinforcement construction and the proportion and type of interlinking yarn on the performance of the composite was assessed.

Hill, B. J.↗

Low Temperature Creep of Hot-Extruded Near-Stoichiometric NiTi Shape Memory Alloy: Isothermal Creep - Part I

This two-part paper is the first published report on the long term, low temperature creep of hot-extruded near-stoichiometric NiTi. Constant load tensile creep tests were conducted on hot-extruded near-stoichiometric NiTi at 300, 373 and 473 K under initial applied stresses varying between 200 and 350 MPa as long as 15 months. These temperatures corresponded to the martensitic, two-phase and austenitic phase regions, respectively. Normal primary creep lasting several months was observed under all conditions indicating dislocation activity. Although steady-state creep was not observed under these conditions, the estimated creep rates varied between 10(exp -10) and 10(exp -9)/s. The creep behavior of the two phases showed significant differences. The martensitic phase exhibited a large strain on loading followed by a primary creep region accumulating a small amount of strain over a period of several months. The loading strain was attributed to the detwinning of the martensitic phase whereas the subsequent strain accumulation was attributed to dislocation glide-controlled creep. An "incubation period" was observed before the occurrence of detwinning. In contrast, the austenitic phase exhibited a relatively smaller loading strain followed by a primary creep region, where the creep strain continued to increase over several months. It is concluded that the creep of the austenitic phase occurs by a dislocation glide-controlled creep mechanism as well as by the nucleation and growth of deformation twins.

Raj, S. V.↗

Shifts in shuttle SRM performance because of ammonium perchlorate crystal shape on missions 51-I/J and 61-A/B

The design of the Space Shuttle vehicle configuration requires that the SRMs produce thrust within tightly-controlled limits. These limits provide assurance that Shuttle ascent performance goals will be achieved within the vehicle flight load constraints. The SRM's will perform within these limits if overall SRM reproducibility is maintained. This report will initially describe the excellent performance reproducibility of the 24 SRMs during the first 12 flights STS-8 through STS-26 (Mission 51-F) using the HPM SRM. Secondly, this report will describe the transient phenomena which interrupted the reproducibility in the first 20 sec of flight for four flights (Missions 51-I/J and 61-A/B). The cause of this 20 sec phenomena is postulated to be a change in the crystal shape of the ammonium perchlorate used in the propellant. This shape change coincided with the performance shift on these four flights. The ballistic effect of the crystal shape change is manifested as a change to the generic HUMP or BARF curve of the Shuttle SRM thrust/pressure-time curve. As the crystal shape change was corrected by the vendor, the performance produced by the Shuttle SRM returned to normal.

Blackwell, D. L.↗

Fabrication and Properties of Composite Artificial Muscles Based on Nylon and a Shape Memory Alloy

This paper focuses on the design, fabrication and investigation of the mechanical properties of new artificial muscles formed by twisting and annealing. The artificial muscles designed by twisting nylon have become a popular topic in the field of smart materials due to their high mechanical performance with a large deformation and power density. However, the complexity of the heating and cooling system required to control the nylon muscle is a disadvantage, so we have proposed a composite artificial muscle for providing a direct electricity-driven actuation by integrating nylon and a shape memory alloy (SMA). In this paper, the design and fabrication process of these composite artificial muscles are introduced before their mechanical properties, which include the deformation, stiffness, load and response, are investigated. The results show that these composite artificial muscles that integrate nylon and a SMA provide better mechanical properties and yield up to a 44.1% deformation and 3.43 N driving forces. The good performance and direct electro-thermal actuation make these composite muscles ideal for driving robots in a method similar to human muscles.

36 MATERIALS SCIENCE↗

An Integrated Design Approach for Infill Patterning of Fused Deposition Modeling and its Application to an Airfoil

We present a new approach to incorporate an internal stress distribution into the design of infill via fused deposition modeling of additive manufacturing (AM). This design approach differs from topology optimization, since the topology optimization of AM focuses on changing the overall shape of the product, whereas the approach we propose in this research focuses on the porous infill and remains the overall shape of the product intact. The approach presented here is effective if the overall shape is an important functioning aspect of a product and the stress is applied to the entire body, not to given localized points. As an application, we demonstrate an airfoil with its infill densities optimized based on the pressure applied during operation. Specifically, the stress of an airfoil is analyzed with operational loading conditions. The local density of the infill pattern is determined based on the computational stress analysis. The infill geometry is mathematically generated using a circle packing algorithm. Test results show that the airfoil with the optimized infill outperforms the same shape with the traditional uniform infill pattern of an airfoil having the same weight.

Kim, Pum↗

Nonlinear Structural Analysis Methodology and Dynamics Scaling of Inflatable Parabolic Reflector Antenna Concepts

Ultra-light weight and ultra-thin membrane inflatable antenna concepts are fast evolving to become the state-of-the-art antenna concepts for deep-space applications. NASA Langley Research Center has been involved in the structural dynamics research on antenna structures. One of the goals of the research is to develop structural analysis methodology for prediction of the static and dynamic response characteristics of the inflatable antenna concepts. This research is focused on the computational studies to use nonlinear large deformation finite element analysis to characterize the ultra-thin membrane responses of the antennas. Recently, structural analyses have been performed on a few parabolic reflector antennas of varying size and shape, which are referred in the paper as 0.3 meters subscale, 2 meters half-scale, and 4 meters full-scale antenna. The various aspects studied included nonlinear analysis methodology and solution techniques, ways to speed convergence in iterative methods, the sensitivities of responses with respect to structural loads, such as inflation pressure, gravity, and pretension loads in the ground and in-space conditions, and the ultra-thin membrane wrinkling characteristics. Several such intrinsic aspects studied have provided valuable insight into evaluation of structural characteristics of such antennas. While analyzing these structural characteristics, a quick study was also made to assess the applicability of dynamics scaling of the half-scale antenna. This paper presents the details of the nonlinear structural analysis results, and discusses the insight gained from the studies on the various intrinsic aspects of the analysis methodology. The predicted reflector surface characteristics of the three inflatable ultra-thin membrane parabolic reflector antenna concepts are presented as easily observable displacement fringe patterns with associated maximum values, and normal mode shapes and associated frequencies. Wrinkling patterns are presented to show how surface wrinkle progress with increasing tension loads. Antenna reflector surface accuracies were found to be very much dependent on the type and size of the antenna, the reflector surface curvature, reflector membrane supports in terms of spacing of catenaries, as well as the amount of applied load.

Sreekantamurthy, Tham↗

Flexible 3D printed silicones for gamma and neutron radiation shielding

Here, resin formulations for direct ink write (DIW) additive manufacturing (AM) were developed for facile customization to shield radiation signatures consisting of a range of gamma radiation and neutron energies in a variety of applications. The resin developed in this work has been formulated to accommodate very high loadings of shielding filler materials: up to 40 wt% bismuth (Bi) metal for gamma radiation shielding, and up to 60 wt% boron-10 ( 10 B) metal for neutron shielding. We report the first instance of a printable resin containing 60 wt% 10 B, which remains flexible after curing despite the high solids content. We demonstrate that these resins can not only tolerate formulation modulation for radiation profile-matched shielding, but they can also be printed in a variety of geometries such that mechanical properties of the printed shield are readily tuned to specific applications. In contrast, most existing shielding materials are rigid, bulky, and do not allow for the complex shapes and mechanical flexibility needed in high-usage applications. This work demonstrates the successful development of a tunable resin for additively manufactured, flexible radiation shielding material, containing high loadings of shielding filler, which can be utilized in harsh radiation environments associated with nuclear materials.

61 RADIATION PROTECTION AND DOSIMETRY↗

Effect of a micro-scale dislocation pileup on the atomic-scale multi-variant phase transformation and twinning

In this paper, we perform concurrent atomistic–continuum (CAC) simulations to assess the contribution of the internal stress induced by the microscale dislocation pileup at an atomically structured interface to the atomic-scale phase transformations (PTs), reverse PTs, and twinning. The main novelty of this work is to unify the atomistic description of the interface and the coarse-grained (CG) description of the lagging dislocations away from the interface within one single framework. Our major findings are: (a) the interface dynamically responds to a pileup by forming steps/ledges, the height of which is proportional to the number of dislocations arriving at the interface; (b) the pileup-induced internal stress concentration profile follows neither the classical Eshelby model nor the super-dislocation model alone, but a combination of them; (c) when the pre-sheared sample is compressed, a direct square-to-hexagonal PT occurs ahead of the pileup tip and eventually grows into a wedge shape. The two variants of the hexagonal phases form a twin with respect to each other; (d) upon a further increase of the loading, part of the newly formed hexagonal phase transforms back to the square phase. The square product phase resulting from this reverse PT forms a twin with respect to the initial square phase. All phase boundaries (PBs) and twin boundaries (TBs) are stationary and correspond to zero thermodynamic Eshelby driving forces; and (e) the microscale dislocation pileup-induced internal shear stress and the structural change at the atomic-scale interface reduces the stress required for initiating a PT by a factor of 5.5, comparing with that in the sample containing no dislocations. This work is the first characterization of the behavior of PTs/twinning resulting from the reaction between a microscale dislocation slip and an atomically structured interface. In conclusion, the gained knowledge will advance our understanding of how the multi-phase material behaves in many complex physical processes, such as the synthesis of multi-phase high-entropy alloys or superhard ceramics under high-pressure torsion, deep mantle earthquakes in geophysics, and so on, which all involve dislocation slip, PTs, twinning, and their interactions across from the atomistic to the microscale and beyond.

36 MATERIALS SCIENCE↗