Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Comparison of inversion models using AIRSAR data for Death Valley, California

Polarimetric Airborne Synthetic Aperture Radar (AIRSAR) data were collected for the Geologic Remote Sensing Field Experiment (GRSFE) over Death Valley, California, USA, in September 1989. AIRSAR is a four-look, quid-polarizaiton, three frequency instrument. It collects measurements at C-band (5.66 cm), L-band (23.98 cm), and P-band (68.13 cm), and has a GIFOV of 10 meters and a swath width of 12 kilometers. Because the radar measures at three wavelengths, different scales of surface roughness are measured. Also, dielectric constants can be calculated from the data. The scene used in this study is in Death Valley, California and is located over Trail Canyon alluvial fan, the valley floor, and Artists Drive alluvial fan. The fans are very different in mineralogic makeup, size, and surface roughness. Trail Canyon fan is located on the west side of the valley at the base of the Panamint Range and is a large fan with older areas of desert pavement and younger active channels. The source for the material on southern part of the fan is mostly quartzites and there is an area of carbonate source on the northern part of the fan. Artists Drive fan is located at the base of the Black Mountains on the east side of the valley and is a smaller, young fan with its source mostly from volcanic rocks. The valley floor contains playa and salt deposits that range from smooth to Devil's Golf course type salt pinnacles.

Kierein-Young, Kathryn S.↗

Application of the kappa-omega Turbulence Model to Quasi-Three-Dimensional Turbomachinery Flows

Many computational fluid dynamics codes for turbomachinery use the Baldwin-Lomax (B-L) turbulence model. It is easy to implement in two dimensions and works well for predicting overall turbomachinery performance. However, it is awkward to implement in three dimensions, often has difficulty finding the length scale, has a crude transition model, and neglects freestream turbulence, surface roughness, and mass injection. The kappa-omega model developed by Wilcox is an appealing alternative for several reasons. First, it is the only two-equation model that can be integrated to the wall without requiring damping functions or the distance to the wall, and hence, should behave well numerically. Second, the effects of freestream turbulence, surface roughness, and mass injection are easily included in the model. Finally, transition can be simulated using the low Reynolds number version of the model. Menter applied the kappa-model to external flows and showed very good results for flows with adverse pressure gradients. Liu and Zheng described their implementation of the kappa-model in a cascade code that included an area change term to account for endwall convergence. They validated the model for a flat plate, and compared the B-L and kappa-models to measured surface pressures for a low-pressure turbine cascade. Since they did not use the low Reynolds number version of the model, their results showed problems resulting from early transition. In this Note the low Reynolds number kappa-model was incorporated in the author's quasi-three-dimensional turbomachinery analysis code. The code includes the effects of rotation, radius change, and stream-surface thickness variation, and also includes the B-L turbulence model. The kappa-omega model was implemented using many of Menter's recommendations and an implicit approximate-factorization scheme described by Baldwin and Barth. The model was tested for a transonic compressor with rotation and variable stream-surface radius and height, and for a transonic turbine vane with transition and heat transfer. Results were compared to the B-L model and to experimental data.

Chima, Rodrick V.↗

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer-by-layer. Alloy 718 powder feedstocks for selective laser melting (SLM) additive manufacturing are produced commercially by both gas and rotary atomization and are available typically in the 10-45 or 15-45 microns size ranges. A comprehensive investigation was conducted to understand the impact of powder variability on the microstructure and mechanical behavior of SLM 718 heat treated to Aerospace Material Specification (AMS) 5664. This study included sixteen virgin powders and three once-recycled powders within the 10-45 and 15-45 microns size ranges that were obtained from seven direct source suppliers and one reseller. Although alike as highly regular spheroids, these powders showed distinct differences in composition (especially Al, C and N contents), particle size distributions, and powder features such as degree of agglomeration, fusion and surface roughness. Compositional differences expectedly had the strongest impact on microstructure. High N and C contents formed TiN-nitrides and/or (Nb,Ti,Mo)-C carbides on the grain boundaries, prevented recrystallization during heat treatment, and resulted in retained (001)-scalloped shaped grains that ranged from 19 to 41 microns in average size. In the absence of this particle pinning, the average grain size of the heat treated SLM 718 ranged from 51 microns to 90 microns. Room temperature tensile and high cycle fatigue (HCF) testing compared as-fabricated (AF) and low stress ground (LSG) surface conditions. Tensile testing revealed consistent behavior between the two surface conditions and amongst the powder lots. The finer grained SLM 718 builds displayed the lowest tensile properties. A SLM 718 build fabricated from a powder with eight times lower C content showed statistically better tensile properties presumably due to enhanced coarsening of (delta)-Ni3Nb precipitates. The specimens from once-recycled powders had slightly higher tensile strengths and slightly higher ductility compared to their virgin equivalents; once-recycling also did not substantially degrade the mean HCF life. The LSG fatigue lives agreed with conventionally manufactured 718 data, while AF lives exhibited a knock-down due to surface roughness. The fatigue lives of AF specimens were statistically equivalent across powder lots except for one and failures typically initiated at stress concentrators associated with SLM surface asperities. Fatigue testing of low stress ground specimens result in both transgranular and within facet crack initiations. More than half of the cracks initiated from these facets for the machined condition; however, these facets appeared to be within grains that were larger-than-average in size. A nitrogen-atomized powder with fine prior particles of TiN-nitrides and M(Ti,Nb,Mo)C carbides from atomization on powder surfaces resulted in the best fatigue performance with segregation of these particles to the SLM 718 grain boundaries leading to higher resistance to early-stage crack propagation. Typically the fine-grained builds with minor phases along the grain boundaries did not perform well in fatigue, whereas a larger-grain build with lower carbon content and coarser delta-Ni3Nb precipitates showed the next best HCF response. Further details of the build microstructure and its impact on tensile and fatigue behavior was considered.

laser deposition↗

AlCu alloy films prepared by the thermal diffusion technique

100-nm thick films of Al{sub 1-x}Cu{sub x} alloys were prepared on glass substrates by thermal diffusion technique. The Cu atomic concentration was varied from 10% to 90%. Alloys were prepared at different temperatures into a vacuum oven with Argon atmosphere. Two thermal processes were used: i) heating the film at 400 deg. C in a single step, and ii) heating the films in sequential steps at 100, 200, 300 and 400 deg. C. Morphology, electrical resistivity, and crystalline orientation of the alloys were studied. The electrical resistivity and surface roughness of the alloys were found to depend strongly on the atomic composition and the diffusion temperature. However, we did not find differences between samples prepared under the two thermal processes. Alloys prepared with x = 0.6 and x = 0.1-0.3 as Cu at concentration exhibited values on electrical resistivity and surface roughness lower than pure Al. Different phases of the Al{sub 1} {sub -} {sub x}Cu{sub x} films were observed as a function of Cu concentration showing a good agreement with the AlCu phase diagram.

36 MATERIALS SCIENCE↗

Electrical properties of epitaxial SrTiO{sub 3} tunnel barriers on (001) Pt/SrTiO{sub 3} substrates

Coherent, epitaxial Pt films with root-mean-square surface roughness values of less than one unit cell were grown on (001) SrTiO{sub 3} substrates by dc sputtering. These Pt films served as bottom electrodes for epitaxial SrTiO{sub 3} tunnel barriers grown by rf magnetron sputtering. The SrTiO{sub 3} barriers were free of pinholes and showed mean surface roughness values of less than one unit cell. Barriers with a thickness of 4.5 nm showed excellent insulating properties and nonlinear current-voltage characteristics. At high bias fields, a reproducible hysteresis and deviation from the ideal tunneling behavior were observed.

36 MATERIALS SCIENCE↗

Characterizing Performance of Additively Manufacturing Regenerative Cooled Combustion Chambers Through Hot Fire Testing

NASA Marshall Space Flight Center (MSFC) has developed several additive manufactured regenerative cooled combustion chambers from 2014 to present. Chambers have been constructed using the Selective Laser Melting (SLM) powder bed additive manufacturing (AM) technique. The materials used for the chambers has varied from Inconel 718, Inconel 625, GRCop-84, and C18150 metal alloys. The surface finish and build techniques used to successfully manufacture combustion chambers using the SLM AM result in as built surface finish and off nominal geometric features. This paper discusses and reviews the effects of surface roughness, flow area, and hydraulic performance of regenerative cooled combustion chambers. The thrust chambers designs tested ranged from 200 to 1,400 psia producing 1,000 to 35,000 lbf thrust. Empirical data from four test campaigns will be reviewed and related to design modeling parameters such as pressure drop, surface roughness, and actual fluid flow geometry. Correlation results with simple 2-D CFD modeling will also be presented. The goal of the work is to better understand how the finished additive manufactured component characteristics inside internal features can effect regenerative cooling chamber design. Adjustments to design methodology will be discussed and recommended based on the above results.

Garcia, C. P.↗

Investigation of NbN x Thin Films and Nanoparticles Grown by Pulsed Laser Deposition and Thermal Diffusion

Niobium nitride films (NbN x ) were grown on Nb and Si (100) substrates using pulsed laser deposition (PLD), laser heating, and thermal diffusion methods. Niobium nitride films were deposited on Nb substrates using PLD with a Q-switched Nd: YAG laser (λ = 1064 nm, 40 ns pulse width, and 10 Hz repetition rate) at different laser fluences, different nitrogen background pressures and deposition temperatures. The effect of changing PLD parameters for films done by PLD was studied. The seen observations establish guidelines for adjusting the laser parameters to achieve the desired morphology and phase of the grown NbN x films. When the fabrication parameters are fixed, except for laser fluence, surface roughness, deposition rate, nitrogen content, and grain size increases with increasing laser fluence. Increasing nitrogen background pressure leads to change in the phase structure of the NbN x films from mixed -Nb 2 N and cubic δ-NbN phases to single hexagonal β-Nb 2 N. A change in substrate temperature led to a pronounced change in the preferred orientation of the crystal structure, the phase transformation, surface roughness, and composition of the films. The structural, electronic, and nanomechanical properties of niobium nitride PLD deposited at different nitrogen pressures (26.7-66.7 Pa) on Si(100) were investigated. The NbN x , films exhibited a cubic δ-NbN with a strong (111) orientation. A correlation between surface morphology, electronic, and superconducting properties was found. The highly-textured δ-NbN films have a T c up to 15.07 K. The film was deposited at a nitrogen background pressure of 66.7 Pa exhibited improved superconducting properties and showed higher hardness values as compared to films deposited at lower nitrogen pressures. NbN nanoclusters that were deposited on carbon coated Cu-grids using PLD at laser fluence of 8 J/cm 2 were observed. Niobium nitride is prepared by heating of Nb sample in a reactive nitrogen atmosphere (133 Pa) at a temperature of 900 °C. The results suggest that the niobium nitride was crystalline in the single phase of hexagonal β-Nb 2 N. As heating time increased, film growth continued with improvement in hardness and modulus. The XRD of samples prepared by a thermal diffusion method at low nitrogen pressure and high temperatures were reported. The samples were prepared at temperatures ranging from 1250-1500 °C. 2D-XRD images of samples, processed at temperature range from 1250 -1500 °C at pressure of 1.3×10 -3 Pa, showed the formation of an α phase. As pressure increased to 0.13 Pa, an α-NbN phase mixed with β-Nb 2 N phase appeared. Niobium nitride samples were prepared by laser nitridation using a Q-switched Nd: YAG nanosecond laser and Ti: sapphire femtosecond lasers. The effects of laser fluence on the formed phase, surface morphology, and electronic properties of the NbN x were investigated. Samples were prepared using Nd: YAG laser are of NbN x in the cubic δ-NbN phase. The femtosecond laser-nitrided samples were prepared by different laser fluences of 0.1-1.3 mJ/cm 2 at 4.0×10 4 Pa nitrogen pressure. NbN x samples with mixedα, β and δ phases were observed. The cubic δ-NbN structure is dominated over the other two phases.

Farha, Ashraf Hassan↗

Implementation of Sacrificial Support Structures for Hybrid Manufacturing of Thin Walls

Thin-walled features can be difficult to produce with traditional machining methods which often rely on excess stock material for stiffness. This challenge is increased in hybrid manufacturing where the feature is already near net shape before machining. Significant workpiece deflection can result in poor geometric and surface finish tolerances on the finished part. A potential solution to this problem is to implement sacrificial support structures to the as-printed geometry. The supports are then machined away during the finishing portion of the hybrid process. In the present work, several different design parameters for these sacrificial supports were evaluated to determine their impact on the quality of representative thin wall geometry samples. The angle, height, and spacing of triangular support structures were varied for each sample and then machined and examined. The addition of these supports relative to an unsupported configuration provided a deflection reduction of around 0.2 mm. Surface roughness was improved by approximately 1.5 µm. Increasing values of support height were found to correspond to reduced wall deflection. Similarly, decreasing values of support angle and support spacing improved geometric accuracy. Efficiency comparisons showed that increases in print time corresponded to rapidly diminishing gains in geometric accuracy but continued to improve surface roughness. Implications for hybrid finishing of additively manufactured thin-walled structures is briefly discussed.

36 MATERIALS SCIENCE↗

Heat Transfer and Boundary-Layer Transition on a Highly Polished Hemisphere-Cone in Free Flight at Mach Numbers Up to 3.14 and Reynolds Numbers Up to 24 x 10(exp 6)

A highly polished hemisphere-cone having a ratio of nose radius to base radius of 0.74 and a half-angle of 14.5 was flight tested at Mach numbers up to 4.70. Temperature and pressure data were obtained at Mach numbers up to 3.14 and a free-stream Reynolds number of 24 x 10(exp 6) based on body diameter. The nose of the model had a surface roughness of 2 to 5 microinches as measured with an interferometer. The measured Stanton numbers were in good agreement with theory. Transition Reynolds numbers based on the laminar boundary-layer momentum thickness at transition ranged from 2,190 to 794. Comparison with results from previous tests of blunt shapes having a surface roughness of 20 to 40 microinches showed that the high degree of polish was instrumental in delaying the transition from laminar to turbulent flow.

Buglia, James J.↗

Optimizing diffusion bonding parameters to maximize the strength of AA6061 aluminum and AZ61A magnesium alloy joints

The main difficulty when joining magnesium (Mg) and aluminum (Al) alloys by fusion welding process lies in the existence of oxide films and formation of brittle intermetallic in the weld region. However, solid-state welding processes such as friction welding and diffusion bonding are suitable processes to join these two materials. The diffusion bonding process parameters such as bonding temperature, bonding pressure, holding time, and surface roughness of the bond specimen play a major role to determine the joint strength. In this investigation, an attempt was made to develop empirical relationships to predict the lap shear strength and bonding strength of diffusion bonded dissimilar joints of AZ61A magnesium and AA6061 aluminum alloys, incorporating the above-mentioned parameters. Response surface methodology (RSM) was applied to optimize the diffusion bonding process parameters to attain the maximum shear strength and bonding strength of the joint. From this investigation, it is found that the bonds fabricated with the bonding temperature of 420.43°C, bonding pressure of 7.70 MPa, holding time of 27.15 min, and surface roughness of 0.10 μm exhibited maximum shear strength and bonding strength of 51.24 and 72.10 MPa, respectively.

36 MATERIALS SCIENCE↗

Interactions between atmospheric pressure plasmas and metallic catalyst particles in packed bed reactors

Atmospheric-pressure plasmas sustained in packed bed reactors (PBRs) are being investigated for chemical conversion of gases and pollution control. Metallic catalysts added to the surfaces of the dielectric beads of PBRs can increase the energy efficiency and selectivity of chemical processes by reducing operating temperature and providing additional reaction pathways. In this paper, results from a computational investigation of plasma surface interactions between micron-scale metallic catalysts and humid-air plasmas in PBRs are discussed. Here we found that high plasma density regions form in the proximity of the metallic catalysts. These higher-density plasma regions were confirmed experimentally using ICCD imaging. The intense plasmas result from geometrical electric field enhancement and redistribution of charges within the conductive particles, leading to further enhancement. The high electric field at the triple points of the catalysts can produce electric field emission of electrons, which provides a pre-ionization source or additional source of electrons. These regions of high electric field and sources of electrons guide discharges towards the catalysts and increases fluxes of excited species, ions, electrons and photons to their surfaces. These fluxes are focused primarily at the triple points between the metal, dielectric and gas. As a result, the catalyst is locally heated, which could lead to further increased rates of thermocatalytic reactions on the surface. Surface roughness of the metal inclusions can lead to additional electric field enhancement, which changes the character of the discharges in the vicinity of the catalysts while reducing breakdown voltage.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Strain-free polished channel-cut crystal monochromators: a new approach and results

The use of channel-cut crystal monochromators has been traditionally limited to applications that can tolerate the rough surface quality from wet etching without polishing. We have previously presented and discussed the motivation for producing channel cut crystals with strain-free polished surfaces [1]. Afterwards, we have undertaken an effort to design and implement an automated machine for polishing channel-cut crystals. The initial effort led to inefficient results. Since then, we conceptualized, designed, and implemented a new version of the channel-cut polishing machine, now called C-CHiRP (Channel-Cut High Resolution Polisher), also known as CCPM V2.0. The new machine design no longer utilizes Figure-8 motion that mimics manual polishing. Instead, the polishing is achieved by a combination of rotary and linear functions of two coordinated motion systems. Here we present the new design of C-CHiRP, its capabilities and features. Multiple channel-cut crystals polished using the C-CHiRP have been deployed into several beamlines at the Advanced Photon Source (APS). We present the measurements of surface finish, flatness, as well as topography results obtained at 1-BM of APS, as compared with results typically achieved when polishing flat-surface monochromator crystals using conventional polishing processes. Limitations of the current machine design, capabilities and considerations for strain-free polishing of highly complex crystals are also discussed, together with an outlook for future developments and improvements.

Kasman, Elina↗

Local Aerodynamic Heat Transfer and Boundary-Layer Transition on Roughened Sphere-Ellipsoid Bodies at Mach Number 3.0

A wind-tunnel investigation was made to determine heat-transfer distributions on three steel sphere-ellipsoid bodies with surface roughnesses of 5, 100, and 200 microinches. Tests were conducted in the Langley 9- by 6-foot thermal structures tunnel at a Mach number of 3.0, free-stream Reynolds numbers (based on model spherical diameter) of 4.25 x 10(exp 6) and 2.76 x l0(exp 6), and at a stagnation temperature of 650 F. Pressure distributions were obtained also on a fourth model. The results indicated that the combination of surface roughness and boundary-layer cooling tended to promote early transition and nullify the advantages attributable to the blunt shape of the model for reducing local temperatures. Good correlation between experimental heating rates and those calculated from laminar theory was achieved up to the start of boundary-layer transition. The correlation also was good with the values predicted by turbulent theory for surface stations downstream from the 45 deg. station.

Deveikis, William D.↗

Volumetric additive manufacturing of silica glass with microscale computed axial lithography

Glass is increasingly desired as a material for manufacturing complex microscopic geometries, from the micro-optics in compact consumer products to microfluidic systems for chemical synthesis and biological analyses. As the size, geometric, surface roughness, and mechanical strength requirements of glass evolve, conventional processing methods are challenged. We introduce microscale computed axial lithography (micro-CAL) of fused silica components, by tomographically illuminating a photopolymer-silica nanocomposite that is then sintered. We fabricated three-dimensional microfluidics with internal diameters of 150 micrometers, free-form micro-optical elements with a surface roughness of 6 nanometers, and complex high-strength trusses and lattice structures with minimum feature sizes of 50 micrometers. As a high-speed, layer-free digital light manufacturing process, micro-CAL can process nanocomposites with high solids content and high geometric freedom, enabling new device structures and applications.

36 MATERIALS SCIENCE↗

Martian terrains

Terrain studies of candidate landing sites for a future rover/sample-return mission to Mars are being conducted to evaluate the geologic and trafficability aspects of each site. An optimum site should have geologic units of widely diverse ages and chemical compositions occurring in close enough proximity and in smooth enough terrain so that a roving vehicle of limited traverse ability (+ or - 100 km) could collect representative samples. In FY 1986, geologic maps were compiled at 1:500,000 and 1:2 million scales of the Mangala Valles, Kasei Valles, Chasma Boreale (north polar), and Planum Australe (south polar) areas, and a study was begun of the topography and surface roughness characteristics of the Mangala Valles site. Geologic mapping has been greatly facilitated by specially enhanced, high-resolution Viking photographs, which clarify stratigraphic relations of units unrecognized earlier. Photoclinometric profiles of topographic features provide width and depth measurements of four classes of channels, the thickness of some volcanic units, and the throw on some faults. Estimates of the surface roughness of units are calculated using a newly developed USGS computer program and using measurements derived from Earth-based radar.

Masursky, Harold↗

The effects of convergence ratio on the implosion behavior of DT layered inertial confinement fusion capsules

The wetted foam capsule design for inertial confinement fusion capsules, which includes a foam layer wetted with deuterium-tritium liquid, enables layered capsule implosions with a wide range of hot-spot convergence ratios (CR) on the National Ignition Facility. In this paper, we present a full-scale wetted foam capsule design that demonstrates high gain in one-dimensional simulations. In these simulations, increasing the convergence ratio leads to an improved capsule yield due to higher hot-spot temperatures and increased fuel areal density. High-resolution two-dimensional simulations of this design are presented with detailed and well resolved models for the capsule fill tube, support tent, surface roughness, and predicted asymmetries in the x-ray drive. Our modeling of these asymmetries is validated by comparisons with available experimental data. In 2D simulations of the full-scale wetted foam capsule design, jetting caused by the fill tube is prevented by the expansion of the tungsten-doped shell layer due to preheat. While the impacts of surface roughness and predicted asymmetries in the x-ray drive are enhanced by convergence effects, likely underpredicted in 2D at high CR, simulations predict that the capsule is robust to these features. Nevertheless, the design is highly susceptible to the effects of the capsule support tent, which negates all of the one-dimensional benefits of increasing the convergence ratio. Indeed, when the support tent is included in simulations, the yield decreases as the convergence ratio is increased for CR > 20. Finally and nevertheless, the results suggest that the full-scale wetted foam design has the potential to outperform ice layer capsules given currently achievable levels of asymmetries when fielded at low convergence ratios (CR < 20).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Process-Defect-Structure-Property Correlations During Laser Powder Bed Fusion of Alloy 718: Role of In Situ and Ex Situ Characterizations

Components made by laser powder bed fusion (L-PBF) additive processes require extensive trial and error optimization to minimize defects and arrive at targeted microstructure and properties. In this paper, in situ infrared thermography and ex situ surface roughness measurements were explored as methodologies to ensure Inconel ® 718-part quality. For a given laser energy of 200 Watts, prismatic samples were produced with different exposure times (80 to 110 µs) and point spacings (80 to 110 µm). The infrared intensities from laser–material interaction zones were measured spatially and temporally. The conditions leading to higher IR intensity and lowest surface roughness values correlated well with less porosity and coarse solidification grain structure. The transition from highly columnar to misoriented growth is attributed to changes in thermal gradients and liquid–solid interface velocities. Hardness measurements and electron microscopy of the as-processed and post-processed heat-treated samples show complex transitions in microstructural states including the heavily dislocated FCC matrix, reduction of dislocation density, and copious precipitation, respectively. These results show that the geometry-process-structure-property correlations are dynamic, and they cascade depending on the transitions of phase states from powder to liquid to solid, as well as phase decompositions and deformations within the solid FCC phase. Finally, validity of using analytical weld process models to describe the above phenomena is also highlighted.

36 MATERIALS SCIENCE↗