Search NASA⌕ Search

SEARCH · Search NASA

Results for “Control Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Wind-tunnel investigation at supersonic speeds of a canard-controlled missile with fixed and free-rolling tail fins

A wind tunnel investigation was made at free stream Mach numbers from 1.70 to 2.86 to determine the effects of fixed and free rolling tail fin afterbodies on the static longitudinal and lateral aerodynamic characteristics of a cruciform canard controlled missile model. The effect of small canard roll and yaw control deflections was also examined. The results indicate that the fixed and free rolling tail configurations have about the same lift curve slope and longitudinal stability level at low angles of attack. For the free rolling tail configuration, the canards provide conventional roll control with no roll control reversal at low angles of attack. The free rolling tail configuration reduced induced roll due to model roll angle and canard yaw control.

Blair, A. B., Jr.↗

Nonlinear modeling of a long flexible manipulator and control by inertial devices

The authors consider the modeling and control of a planar, long flexible manipulator that is representative of current space-based robotic arms. The arm is equipped with three actuators: 1) a shoulder motor; 2) a torque wheel at the tip; and 3) a proof-mass actuator at the tip. The goal is to investigate the potential use of inertial devices as control inputs for maneuvering tasks and vibration suppression. The parameters used for the inertial devices at the tip are comparable to those specified for the Mini-Mast facility at the Langley Research Center. A nonlinear distributed parameter model is obtained by the extended Hamilton principle. The associated eigenvalue/eigenfunction problem is solved and a finite-dimensional state space model is assembled. A preliminary design of a linear quadratic regulator is used, and computer simulation results illustrate the benefits of using the proposed actuators.

Barbieri, Enrique↗

Morpheus Lander Roll Control System and Wind Modeling

The Morpheus prototype lander is a testbed capable of vertical takeoff and landing developed by NASA Johnson Space Center to assess advanced space technologies. Morpheus completed a series of flight tests at Kennedy Space Center to demonstrate autonomous landing and hazard avoidance for future exploration missions. As a prototype vehicle being tested in Earth's atmosphere, Morpheus requires a robust roll control system to counteract aerodynamic forces. This paper describes the control algorithm designed that commands jet firing and delay times based on roll orientation. Design, analysis, and testing are supported using a high fidelity, 6 degree-of-freedom simulation of vehicle dynamics. This paper also details the wind profiles generated using historical wind data, which are necessary to validate the roll control system in the simulation environment. In preparation for Morpheus testing, the wind model was expanded to create day-of-flight wind profiles based on data delivered by Kennedy Space Center. After the test campaign, a comparison of flight and simulation performance was completed to provide additional model validation.

Gambone, Elisabeth A.↗

Initial comparison of single cylinder Stirling engine computer model predictions with test results

A NASA developed digital computer code for a Stirling engine, modelling the performance of a single cylinder rhombic drive ground performance unit (GPU), is presented and its predictions are compared to test results. The GPU engine incorporates eight regenerator/cooler units and the engine working space is modelled by thirteen control volumes. The model calculates indicated power and efficiency for a given engine speed, mean pressure, heater and expansion space metal temperatures and cooler water inlet temperature and flow rate. Comparison of predicted and observed powers implies that the reference pressure drop calculations underestimate actual pressure drop, possibly due to oil contamination in the regenerator/cooler units, methane contamination in the working gas or the underestimation of mechanical loss. For a working gas of hydrogen, the predicted values of brake power are from 0 to 6% higher than experimental values, and brake efficiency is 6 to 16% higher, while for helium the predicted brake power and efficiency are 2 to 15% higher than the experimental.

Tew, R. C., Jr.↗

Progress towards large wind tunnel magnetic suspension and balance systems

Recent developments and current research efforts leading towards realization of a large scale production wind tunnel Magnetic Suspension and Balance facility are reviewed. Progress has been made in the areas of model roll control, high angle-of-attack testing, digital system control, high magnetic moment superconducting solenoid model cores, and system failure tolerance. Formal design studies of large scale facilities have commenced and are continuing.

Britcher, C. P.↗

Position Control for Non-linear, Multiple-Link Robots

Several approaches to complicated control problem examined. Report surveys methods for controlling motion of robot manipulators. Applies to coupled, highly nonlinear multiple-link robots. Presents adaptive control technique based on discrete linear model of robot arm, obtained by linearizing nonlinear dynamical equations about nominal trajectory. Parameters of model calculated with adaptive parameter-identification algorithm. Based on system model, optimal control input computed using position and velocity feedback.

Seraji, H.↗

Actively Controlled Landing Gear for Aircraft Vibration Reduction

Concepts for long-range air travel are characterized by airframe designs with long, slender, relatively flexible fuselages. One aspect often overlooked is ground induced vibration of these aircraft. This paper presents an analytical and experimental study of reducing ground-induced aircraft vibration loads using actively controlled landing gears. A facility has been developed to test various active landing gear control concepts and their performance. The facility uses a NAVY A6-intruder landing gear fitted with an auxiliary hydraulic supply electronically controlled by servo valves. An analytical model of the gear is presented including modifications to actuate the gear externally and test data is used to validate the model. The control design is described and closed-loop test and analysis comparisons are presented.

Horta, Lucas G.↗

Sweep and Compressibility Effects on Active Separation Control at High Reynolds Numbers

This paper explores the effects of compressibility, sweep and excitation location on active separation control at high Reynolds numbers. The model, which was tested in a cryogenic pressurized wind tunnel, simulates the upper surface of a 20% thick Glauert Goldschmied type airfoil at zero angle of attack. The flow is fully turbulent since the tunnel sidewall boundary layer flows over the model. Without control, the flow separates at the highly convex area and a large turbulent separation bubble is formed. Periodic excitation is applied to gradually eliminate the separation bubble. Two alternative blowing slot locations as well as the effect of compressibility, sweep and steady suction or blowing were studied. During the test the Reynolds numbers ranged from 2 to 40 million and Mach numbers ranged from 0.2 to 0.7. Sweep angles were 0 and 30 deg. It was found that excitation must be introduced slightly upstream of the separation region regardless of the sweep angle at low Mach number. Introduction of excitation upstream of the shock wave is more effective than at its foot. Compressibility reduces the ability of steady mass transfer and periodic excitation to control the separation bubble but excitation has an effect on the integral parameters, which is similar to that observed in low Mach numbers. The conventional swept flow scaling is valid for fully and even partially attached flow, but different scaling is required for the separated 3D flow. The effectiveness of the active control is not reduced by sweep. Detailed flow field dynamics are described in the accompanying paper.

Seifert, Avi↗

Sweep and Compressibility Effects on Active Separation Control at High Reynolds Numbers

This paper explores the effects of compressibility, sweep and excitation location on active separation control at high Reynolds numbers. The model, which was tested in a cryogenic pressurized wind tunnel, simulates the upper surface of a 20% thick GlauertGoldschmied type airfoil at zero angle of attack. The flow is fully turbulent since the tunnel sidewall boundary layer flows over the model. Without control, the flow separates at the highly convex area and a large turbulent separation bubble is formed. Periodic excitation is applied to gradually eliminate the separation bubble. Two alternative blowing slot locations as well as the effect of compressibility, sweep and steady suction or blowing were studied. During the test the Reynolds numbers ranged from 2 to 40 million and Mach numbers ranged from 0.2 to 0.7. Sweep angles were 0 and 30 deg. It was found that excitation must be introduced slightly upstream of the separation region regardless of the sweep angle at low Mach number. Introduction of excitation upstream of the shock wave is more effective than at its foot. Compressibility reduces the ability of steady mass transfer and periodic excitation to control the separation bubble but excitation has an effect on the integral parameters, which is similar to that observed in low Mach numbers. The conventional swept flow scaling is valid for fully and even partially attached flow, but different scaling is required for the separated 3D flow. The effectiveness of the active control is not reduced by sweep. Detailed flow field dynamics are described in the accompanying paper.

Seifert, Avi↗

Performance of Cassini Reaction Wheel Friction Compensation Scheme During Spin Rate Zero-Crossing and Drag Spikes

Cassini uses reaction wheels to achieve the spacecraft pointing stability that is needed during imaging operations of several science instruments. The Cassini flight software makes inflight estimates of reaction wheel bearing drag torque and the reaction wheel controller uses these estimates to achieve a high level of spacecraft pointing stability. However, the Cassini drag torque estimator was designed to accurately track the bearing drag torque only in the steady state. When the physical drag torque changes abruptly (for example, during a reaction wheel spin rate reversal or when wheel bearings experienced drag spikes), the drag estimator will not be able to track the physical drag closely. This will lead to a degradation in the spacecraft pointing stability performance. For Cassini, this was not a problem because of the significant performance margin in pointing stability. However, for missions that have very challenging pointing stability requirements and that must perform well in the presence of frequent wheel rate reversals, alternative drag-compensating control schemes must be considered. To this end, alternative drag torque compensating control schemes (such as the adaptive model reference control scheme) are briefly reviewed in this paper. Selected design features used in these friction compensation schemes may be incorporated in reaction wheel controller design to improve the robustness of spacecraft pointing stability performance with regard to a wide range of reaction wheel drag torque anomalous behavior.

Lee, Allan Y↗

A Multiple Agent Model of Human Performance in Automated Air Traffic Control and Flight Management Operations

A predictive model of human operator performance (flight crew and air traffic control (ATC)) has been developed and applied in order to evaluate the impact of automation developments in flight management and air traffic control. The model is used to predict the performance of a two person flight crew and the ATC operators generating and responding to clearances aided by the Center TRACON Automation System (CTAS). The purpose of the modeling is to support evaluation and design of automated aids for flight management and airspace management and to predict required changes in procedure both air and ground in response to advancing automation in both domains. Additional information is contained in the original extended abstract.

Corker, Kevin↗

Feasibility of Varying Geo-Fence Around an Unmanned Aircraft Operation Based on Vehicle Performance and Wind

Managing trajectory separation is critical to ensuring accessibility, efficiency, and safety in the unmanned airspace. The notion of geo-fences is an emerging concept, where distance buffers enclose individual trajectories and areas of operation in order to manage the airspace. Currently, the Air Traffic Management system for commercial travel defines static distance buffers around the aircraft; however, commercial UASs are envisioned to operate in significantly closer proximity to other UAS requiring a geo-fence for spacing operations. The geo-fence size can be determined based on vehicle performance characteristics, state of the airspace, weather, and other unforeseen events such as emergency or disaster response. Calculation of the geo-fence size could be determined as part of pre-flight planning and during real-time operations. A largely non-homogeneous fleet of UASs will be operating in low altitude and will likely be commercially developed. Due to intellectual property concerns, the operators may not provide detailed specifications of the control system to UTM. In addition, the huge variety of UAS makes modeling each control system prohibitive and flight data for these vehicles may not exist. Therefore, a generalized, simple geo-fence sizing algorithm must be developed such that it does not rely on detailed knowledge of the vehicle control system, accounts for the presence of urban winds, and is sufficiently accurate. In this work, two simple models are investigated to determine its feasibility as an adequate means for calculating the geo-fence size. The vehicle data used in this work are provided by UAS manufactures who have partnered with NASA's UTM project and some publicly available websites. The first model utilizes wind data processed from the NOAA HRRR (Hourly Rapid Refresh) product and Sonar Annemometer data provided by San Jose State. The second model utilizes OpenFOAM which is a CFD code used to generate a wind field for flow around a single building. The key vehicle performance parameters can include UAS response time to disturbances, command to actuation latency, control system rate limits, time to recovery to desired path, and aerodynamics. It was found that the first model provides an initial understanding of geo-fence sizing, but does not provide enough accuracy to provide UTM with an efficient means of scheduling vehicles. The results of the second model reveal that modeling UAS controls systems with a linearized plant and gain scheduled PID controller does not allow capture the UAS flight dynamics within a significant envelope of the wind disturbances.

uncertainty↗

Adaptive Failure Compensation for Aircraft Tracking Control Using Engine Differential Based Model

An aircraft model that incorporates independently adjustable engine throttles and ailerons is employed to develop an adaptive control scheme in the presence of actuator failures. This model captures the key features of aircraft flight dynamics when in the engine differential mode. Based on this model an adaptive feedback control scheme for asymptotic state tracking is developed and applied to a transport aircraft model in the presence of two types of failures during operation, rudder failure and aileron failure. Simulation results are presented to demonstrate the adaptive failure compensation scheme.

Liu, Yu↗

CFD Modeling for Active Flow Control

This presentation describes current work under UEET Active Flow Control CFD Research Tool Development. The goal of this work is to develop computational tools for inlet active flow control design. This year s objectives were to perform CFD simulations of fully gridded vane vortex generators, micro-vortex genera- tors, and synthetic jets, and to compare flowfield results with wind tunnel tests of simple geometries with flow control devices. Comparisons are shown for a single micro-vortex generator on a flat plate, and for flow over an expansion ramp with sidewall effects. Vortex core location, pressure gradient and oil flow patterns are compared between experiment and computation. This work lays the groundwork for evaluating simplified modeling of arrays of devices, and provides the opportunity to test simple flow control device/sensor/ control loop interaction.

Buning, Pieter G.↗

Inverse Modelling to Obtain Head Movement Controller Signal

Experimentally obtained dynamics of time-optimal, horizontal head rotations have previously been simulated by a sixth order, nonlinear model driven by rectangular control signals. Electromyography (EMG) recordings have spects which differ in detail from the theoretical rectangular pulsed control signal. Control signals for time-optimal as well as sub-optimal horizontal head rotations were obtained by means of an inverse modelling procedures. With experimentally measured dynamical data serving as the input, this procedure inverts the model to produce the neurological control signals driving muscles and plant. The relationships between these controller signals, and EMG records should contribute to the understanding of the neurological control of movements.

Kim, W. S.↗