Search NASA⌕ Search

SEARCH · Search NASA

Results for “Direct current system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Force field preconditioned ab initio structure relaxation method

We present a general method to accelerate ab initio atomic structural relaxations. In this method, the conjugate gradient ab initio relaxation is preconditioned by a force field relaxation. This force field is constructed on-the-flight with the information of the ab initio forces and the current atomic configuration. At each ab initio relaxation step, the so-constructed force field is used to prerelax the system, with the relaxation direction as the preconditioned direction for the ab initio conjugated gradient method. The force field model and its parameters are rather general making this method applicable for a wide range of systems commonly used in material simulations. We report more than 80 different systems have been tested representing different cases in material simulations. Across the board, we find accelerations mostly over a factor of 2 and for some large systems with a factor of 6 ~ 9 . There is no case where the relaxation becomes worse. The code and lib for this method are provided, which can be used as a plugin in a standard ab initio atomic relaxation code.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dynamic Model of Active Front-End Converters with 2DOF-PI Controllers for DC Bus Voltage Control

In most of the research, a conventional one degree-of-freedom type proportional-integral controller (1DOF-PI) is used for the regulation of the dc bus voltage in an Active Front-End Converter (AFEC). This paper proposes a two degree-of-freedom type proportional-integral controller (2DOF-PI) for the regulation of dc bus voltage in an AFEC. Such a controller eliminates the left-half plane (LHP) zero in the command-to-output transfer function for dc bus voltage regulation that is inherent to the conventional 1DOF-PI for this application. The dynamic model of an AFEC in the synchronous reference frame (SRF) is presented. An inner current control and outer dc voltage control loop is built for controlling the AFEC. Vector-control scheme is employed to achieve decoupled control of direct-axis and quadrature-axis currents. The outer dc voltage control loop is designed with a 2DOF-PI to complete the control system. Transfer function (TF) of the controller is derived based on the presented model and used to calculate the controller gains. Transient and steady state performance of the designed controllers are investigated in MATLAB/Simulink and results presented.

Thapa, Anup↗

Efficient Scalable Parallel Higher Order Direct MoM-SIE Method With Hierarchically Semiseparable Structures for 3-D Scattering

A novel fast scalable parallel algorithm is proposed for the solution of large 3-D scattering problems based on: 1) the double (geometrical and current-approximation) higher order (DHO) method of moments (MoM) in the surface integral equation (SIE) formulation and 2) a direct solver for dense linear systems utilizing hierarchically semiseparable (HSS) structures. Namely, an HSS matrix representation is used for compression, factorization, and solution of the system matrix. In addition, a rank-revealing QR decomposition for memory compression is used, with a stopping criterion in terms of the relative rank tolerance value. One method for geometrical preprocessing of the scatterers based on the cobblestone distance sorting technique is employed in order to enhance the HSS algorithm accuracy and parallelization. Numerical examples show how the accuracy of the DHO HSS-MoM-SIE method is easily controllable by using the relative tolerance for the matrix compression. Furthermore, the examples demonstrate low memory consumption, as well as much faster simulation time, when compared to the direct LU decomposition. The method enables dramatically faster monostatic scattering computations than iterative solvers and reduced number of unknowns when compared to low-order discretizations. Finally, great scalability of the algorithm is demonstrated on more than one thousand processes.

97 MATHEMATICS AND COMPUTING↗

Bringing Water into an Integrated Assessment Framework

We developed a modeling capability to understand how water is allocated within a river basin and examined present and future water allocations among agriculture, energy production, other human requirements, and ecological needs. Water is an essential natural resource needed for food and fiber production, household and industrial uses, energy production, transportation, tourism and recreation, and the functioning of natural ecosystems. Anthropogenic climate change and population growth are anticipated to impose unprecedented pressure on water resources during this century. Pacific Northwest National Laboratory (PNNL) researchers have pioneered the development of integrated assessment (IA) models for the analysis of energy and economic systems under conditions of climate change. This Laboratory Directed Research and Development (LDRD) effort led to the development of a modeling capability to evaluate current and future water allocations between human requirements and ecosystem services. The Water Prototype Model (WPM) was built in STELLA®, a computer modeling package with a powerful interface that enables users to construct dynamic models to simulate and integrate many processes (biological, hydrological, economics, sociological). A 150,404-km2 basin in the United States (U.S.) Pacific Northwest region served as the platform for the development of the WPM. About 60% of the study basin is in the state of Washington with the rest in Oregon. The Columbia River runs through the basin for 874 km, starting at the international border with Canada and ending (for the purpose of the simulation) at The Dalles dam. Water enters the basin through precipitation and from streamflows originating from the Columbia River at the international border with Canada, the Spokane River, and the Snake River. Water leaves the basin through evapotranspiration, consumptive uses (irrigation, livestock, domestic, commercial, mining, industrial, and off-stream power generation), and streamflow through The Dalles dam. Water also enters the Columbia River via runoff from land. The model runs on a monthly timescale to account for the impact of seasonal variations of climate, streamflows, and water uses. Data for the model prototype were obtained from national databases and ecosystem model results. The WPM can be run from three sources: 1) directly from STELLA, 2) with the isee Player®, or 3) the web version of WPM constructed with NetSim® software. When running any of these three versions, the user is presented a screen with a series of buttons, graphs, and a table. Two of the buttons provide the user with background and instructions on how to run the model. Currently, there are five types of scenarios that can be manipulated alone or in combination using the Sliding Input Devices: 1) interannual variability (e.g., El Niño), 2) climate change, 3) salmon policy, 4) future population, and 5) biodiesel production. Overall, the WPM captured the effects of streamflow conditions on hydropower production. Under La Niña conditions, more hydropower is available during all months of the year, with a substantially higher availability during spring and summer. Under El Niño conditions, hydropower would be reduced, with a total decline of 15% from normal weather conditions over the year. A policy of flow augmentation to facilitate the spring migration of smolts to the ocean would also reduce hydropower supply. Modeled hydropower generation was 23% greater than the 81 TWh reported in the 1995 U.S. Geological Survey (USGS) database. The modeling capability presented here contains the essential features to conduct basin-scale analyses of water allocation under current and future climates. Due to its underlying data structure iv and conceptual foundation, the WPM should be appropriate to conduct IA modeling at national and global scales.

54 ENVIRONMENTAL SCIENCES↗

Preparing the Way for New Policy Regarding Adaptation of US Electricity Infrastructure to Climate Change

The following pages represent the status of policy regarding adaptation of the electric grid to climate change and proposed directions for new policy development. While strides are being made to understand the current climate and to predict hazards it may present to human systems, both the science and the policy remain at present in an analytical state. The policy proposed in this document involves first continued computational modeling of outcomes which will produce a portfolio of options to be considered in light of specific region-related risks. It is proposed that the modeling continue not only until reasonable policy at various levels of jurisdiction can be derived from its outcome but also on a continuing basis so that as improvements in the understanding of the state and trajectory of climate science along with advancements in technology arise, they can be incorporated into an appropriate and evolving policy.

Allen, Melissa R.↗

A Thruster Sub-System Module (TSSM) for solar electric propulsion

Solar Electric Propulsion (SEP) is currently being studied for possible use in a number of near-earth and planetary missions. Thruster systems for these missions could be integrated directly into a spacecraft or modularized into a Thruster Sub-System Module (TSSM). A TSSM for electric propulsion missions would consist of a 30-cm ion thruster, thruster gimbal system, propellant storage and feed system, associated Power Processing Unit (PPU), thermal control system and complete supporting structure. The TSSM would be wholly self-contained and be essentially a plug-in or strap-on electric stage with simple mechanical, thermal, electrical and propellant interfaces. The TSSM described in this report is designed for a broad range of missions requiring from two to ten TSSM's mounted in a 2 by x configuration. The thermal control system is designed to accommodate waste heat from the power processor based on realistic efficiencies when the TSSM is operating from 0.7 to 3.5 AU's. The modules are 0.61 M (2 ft) wide by 2.29 M (7.5 ft) long and have a dry weight including propellant tank of 54.4 kg (120 lb). The propellant tank will hold 145.1 kg (320 lb) of mercury.

Sharp, G. R.↗

Solar-Driven Liquid-Metal MHD Generator

Liquid-metal magnetohydrodynamic (MHD) power generator with solar oven as its heat source has potential to produce electric power in space and on Earth at high efficiency. Generator focuses radiation from Sun to heat driving gas that pushes liquid metal past magnetic coil. Power is extracted directly from electric currents set up in conducting liquid. Using solar energy as fuel can save considerable costs and payload weight, compared to previous systems.

Hohl, F.↗

Test results of high-voltage, high-power, solid-state remote power controllers

This report discusses the results of testing high-voltage, high-power, solid-state remote power controllers (RPC) using RPCs designed and built by John C. Sturman at the Lewis Research Center, Cleveland, Ohio, and utilizing the Autonomously Managed Power Systems (AMPS) breadboard/test facility. These test results are used to determine usefulness of the RPCs for future applications in high-voltage direct-current space power.

Johnson, Yvette Binford↗

Evolution of Local Microstructures of Clusters Undergoing 2-Dimensional Diffusion

A primary objective of our current work is to study the details of evolving microstructures through a study of "island" formation in heteroepitaxial film/substrate systems. Such systems could be of direct relevance to so-called mixed-dimensional coarsening and to the study of heterostructures grown by thin-film techniques. The spontaneous formation of three-dimensional islands in strained-layer heteroepitaxy, e.g., has emerged as a new technique for the synthesis of self-assembled quantum dots. This work focuses on coarsening by two-dimensional diffusion of three-dimensional droplets on a flat surface.

Frazier, Donald O.↗

A Perspective on DSN System Performance Analysis

This paper discusses the performance analysis effort being carried out in the NASA Deep Space Network. The activity involves root cause analysis of failures and assessment of key performance metrics. The root cause analysis helps pinpoint the true cause of observed problems so that proper correction can be effected. The assessment currently focuses on three aspects: (1) data delivery metrics such as Quantity, Quality, Continuity, and Latency; (2) link-performance metrics such as antenna pointing, system noise temperature, Doppler noise, frequency and time synchronization, wide-area-network loading, link-configuration setup time; and (3) reliability, maintainability, availability metrics. The analysis establishes whether the current system is meeting its specifications and if so, how much margin is available. The findings help identify the weak points in the system and direct attention of programmatic investment for performance improvement.

Deep Space Network (DSN)↗

2022 Small Turbine Certification Awardee: NPS Solutions

Inverters convert the direct current power generated by wind turbines into the alternating current needed to serve local loads and feed onto the electricity grid. Although distributed wind systems typically supply electricity for homes and businesses near the turbines, these systems can also provide clean power to strengthen grid resilience. Certification to UL 1741 SA ensures that inverters will enable distributed wind turbines to provide grid support services and stay online when the grid experiences stability issues. Small companies often find the electrical listing process too complex and expensive to undertake on their own, so few distributed wind turbine inverters are certified to this standard. A U.S. Department of Energy (DOE) Competitiveness Improvement Project (CIP) award is helping NPS Solutions (NPS) secure this critical certification for the inverter in its 100-kilowatt NPS 100C wind turbine, which is optimized for on-site generation at farms, businesses, schools, hospitals, and remote locations.

CIP↗

Testing of Liquid Metal Components for Nuclear Surface Power Systems

The Early Flight Fission Test Facility (EFF-TF) was established by the Marshall Space Flight Center (MSFC) to provide a capability for performing hardware-directed activities to support multiple in-space nuclear reactor concepts by using a non-nuclear test methodology. This includes fabrication and testing at both the module/component level and near prototypic reactor configurations. The EFF-TF is currently supporting an effort to develop an affordable fission surface power (AFSP) system that could be deployed on the Lunar surface. The AFSP system is presently based on a pumped liquid metal-cooled (Sodium-Potassium eutectic, NaK-78) reactor design. This design was derived from the only fission system that the United States has deployed for space operation, the Systems for Nuclear Auxiliary Power (SNAP) 10A reactor, which was launched in 1965. Two prototypical components recently tested at MSFC were a pair of Stirling power conversion units that would be used in a reactor system to convert heat to electricity, and an annular linear induction pump (ALIP) that uses travelling electromagnetic fields to pump the liquid metal coolant through the reactor loop. First ever tests were conducted at MSFC to determine baseline performance of a pair of 1 kW Stirling convertors using NaK as the hot side working fluid. A special test rig was designed and constructed and testing was conducted inside a vacuum chamber at MSFC. This test rig delivered pumped NaK for the hot end temperature to the Stirlings and water as the working fluid on the cold end temperature. These test were conducted through a hot end temperature range between 400 to 550C in increments of 50 C and a cold end temperature range from 30 to 70 C in 20 C increments. Piston amplitudes were varied from 6 to 1 1mm in .5 mm increments. A maximum of 2240 Watts electric was produced at the design point of 550 hot end, 40 C cold end with a piston amplitude of 10.5mm. This power level was reached at a gross thermal efficiency of 28%. A baseline performance map was established for the pair of 1kW Stirling convertors. The performance data will then be used for design modification to the Stirling convertors. The ALIP tested at MSFC has no moving parts and no direct electrical connections to the liquid metal containing components. Pressure is developed by the interaction of the magnetic field produced by the stator and the current which flows as a result of the voltage induced in the liquid metal contained in the pump duct. Flow is controlled by variation of the voltage supplied to the pump windings. Under steady-state conditions, pump performance is measured for flow rates from 0.5-4.3 kg/s. The pressure rise developed by the pump to support these flow rates is roughly 5-65 kPa. The RMS input voltage (phase-to-phase voltage) ranges from 5-120 V, while the frequency can be varied arbitrarily up to 60 Hz. Performance is quantified at different loop temperature levels from 50 C up to 650 C, which is the peak operating temperature of the proposed AFSP reactor. The transient response of the pump is also evaluated to determine its behavior during startup and shut-down procedures.

Polzin, Kurt A.↗

In-Situ Monitoring Assisted Large-Scale Additive Manufacturing of Mild Steel and 316L Alloys for Nuclear Application

The Advanced Materials and Manufacturing Technologies (AMMT) Program is aimed at developing cross-cutting technologies in support of a broad range of nuclear reactor parts, and to maintain U.S. leadership in materials and manufacturing technologies for nuclear energy applications. The overarching vision of the AMMT program is to accelerate the development, qualification, demonstration and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy. One of its three goals is to target big challenges and game-changing technologies, to realize the mission and vision of AMMT program. Based on this context, this multi-year work package focuses on understanding the current state of large-scale additive manufacturing (AM) technology for the deposition of 316L stainless steel materials for final components and mild steel for use in nuclear manufacturing processes. The targeted AM modality is directed energy deposition (DED), capable of fabricating components on the size scale of meters including valves, pumps, impellers. etc. that are challenging or difficult to source, especially when developing new systems or replacing obsolete components. Accordingly, the current writeup aims at providing a baseline literature survey on structure-property relationships in mild steel and 316L alloys. Also, information on preliminary trials to date involving these two alloys show tremendous potential of printing parts having complex geometry and thin- walled structures, such as nuclear valve and Hot isostatic Press (HIP) can, using wire based (Wire Arc Additive Manufacturing and Hybrid Additive Manufacturing) as well as blown powder DED machines. All of this is aimed towards (i) demonstrating the ability to fabricate large components for pressure boundary applications relevant to the nuclear community and nuclear manufacturing technology, and (ii) understanding the effect of different manufacturing technology on AM can production and post HIPed material for nuclear applications. Another target of this writeup is to compile various in-situ monitoring tools that have been incorporated for different DED AM modalities, in order to understand process variability during the entire fabrication process. This can be correlated with processing-structure-property response surfaces and would add confidence around process quality verification and ultimately component certification for nuclear applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Analysis and Overview of Hybrid Wired and Wireless Bi-Directional EV Charger Systems

Here, this paper analyzes and overviews hybrid wired and wireless bi-directional Electric Vehicle (EV) charging systems with a primary focus on resonant compensation methods that enable a unified power conversion architecture. Four compensation configurations based on series–series and LCC–LCC resonant networks are systematically evaluated for both wired transformer-based and wireless coupler-based operation. The analysis examines how coupling conditions, resonant component selection, and auxiliary compensation tuning influence voltage gain characteristics, resonant tank current magnitude and phase, and operating frequency requirements. Normalized frequency-domain results are presented to directly compare reactive current behavior and voltage regulation capability under wired and wireless operating conditions. A 60 kW bi-directional charger case study is used to demonstrate the feasibility of retaining a common hardware platform while accommodating distinct coupling scenarios through compensation tuning rather than structural modification. The presented results provide design-oriented insights into resonant network selection and compensation strategies for scalable and flexible hybrid EV charging systems.

Hybrid↗

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

Understanding and Utilizing PBL Height Data from Multiple Observing Systems in the GEOS System

The accuracy of PBL height simulation is a key issue in many applications including forecasting near surface meteorology and air quality, however, it is a very challenging problem due to the lack of not only comprehensive, global Planetary Boundary Layer (PBL) observations but also a strategy and infrastructure to utilize PBL height data from a variety of sensors. Following the designation of PBL as an incubation class observable in the 2017 Decadal Survey, the PBL Incubation Study Team Report [14] made clear that “a future global PBL observing system requires modeling and data assimilation as essential components.” There is an urgent need for global modeling development in order to utilize Program of Record (POR) observations, assess their impacts, and identify gaps to be filled by future PBL missions. Our overall objective is to develop PBL data assimilation capabilities in the NASA Global Earth Observing System (GEOS), focusing on PBL height from multiple observing systems, to support the assessment and use of future PBL observations. The NASA GEOS system is composed of the GEOS global atmospheric general circulation model (AGCM) and the atmospheric data assimilation system (ADAS). The PBL parameterizations include the “Lock” K-profile scheme driven by surface and cloud-top buoyancy fluxes ([4]), and the “Louis” local scheme for stable conditions based on the Richardson number ([5]). Above the mixed layer defined by the Lock surface plume, shallow cumulus convection is represented by the mass flux scheme of [9]. Additional parameterizations are summarized in [1]. The ADAS employs the hybrid 4D Ensemble- Variational (EnVar) configuration ([15]), with the ensemble providing flow-dependent background error covariance information. The resultant analysis increments are fed back to the forecast model through the 4D incremental analysis update (IAU) approach ([11]). In this study, PBL height data are being or have been generated from radiosondes, GNSS RO, satellite (CATS, CALIPSO and ICESat-2) and ground-based (MPLNET) lidars, and wind profiler. Investigations have been conducted to specify quality marks for PBL height retrievals for the data assimilation purpose. These PBL height data have different strengths and weaknesses ([2], [3], [6], [7], [8], [10]), and the satellite PBL height data provide better global coverage and complement in-situ PBL height data. Radiosondes offer high accuracy and in situ measurement of temperature and humidity profiles, but with poor spatio-temporal sampling. The in-situ observing systems like MPLNET and wind profiler provide long history of PBL height records at each station. The GNSS RO based PBL height is retrieved based on the sharp gradients in refractivity profile that represent the fine vertical structure of temperature and moisture changes above the PBL. However, not all RO refractivity profiles reach the surface depending on location and regime, and RO refractivity retrievals can be negatively biased below 2km. The PBL height data from satellite lidars provide high resolution along track PBL height retrievals, but over land they are affected by previous day convective PBL aerosol and strongly associated with mixing layer and retrievals cannot be made below thick, attenuating clouds. A successful assimilation of PBL height data requires a thorough understanding of the observing method and the retrieval algorithm for each observing system in order to use the PBL height data from multiple observing systems properly. Due to the sensitivity of PBL height data to the observing method and choice of algorithm, it is important to use a model definition appropriate for each observation type to compute differences between PBL height data and model PBL height (OmFs). The GEOS model currently includes two PBL height definitions suitable for direct comparison with observed PBL height, and additional definitions are being added in this study. Evaluation of different model PBL height definitions is underway. Meanwhile, efforts have been made in the GEOS data assimilation system to develop PBL height data assimilation capability. PBL height data can be assimilated using two different approaches. The traditional approach is to construct an observation operator and its tangent linear and adjoint, which link control variables to PBL height data from each observing system. This observation operator can be very complicated, e.g., the lidar-based PBL height observation operator includes the backscatter lidar forward observation operator, the algorithm to derive PBL height from attenuated total backscatter, interpolation, and calculations handling the mismatch between observed and model scales. The other approach is to augment PBL height to the control variable vector, and it is adopted in this study. The latter approach was also used in previous studies, e.g., the assimilation of PBL height data from radiosonde and aircraft in the Real Time Mesoscale Analysis (RTMA) system for a dispersion modelling study ([13]); the PBL height assimilation study using lidar PBL height data at Greensburg, Kansas for a field campaign ([12]). The PBL height assimilation from multiple observing systems in this study allows us to take advantage of the diverse PBL height data that provide much better global coverage collectively under different meteorological conditions and with different temporal and spatial scales. As all the PBL heights are tightly coupled with the PBL thermodynamic variables, the strong correlations, which are provided by the 4D ensemble forecast, enable PBL height data from various sources to interact and combine coherently and provide additional information for PBL temperature and moisture fields. The results of comparisons among PBL height data from different sources and the evaluation of the model PBL height definitions with the PBL height data will be presented, and the PBL height data synergy strategies and preliminary results will also be discussed at the conference.

Y. Zhu↗

Evolution of the Data Quality Monitoring and Prompt Processing System in the proto DUNE-SP experiment

The DUNE Collaboration currently operates an experimental program based at CERN which includes a beam test and an extended cosmic ray run of two large-scale prototypes of the massive Liquid Argon Time Projection Chamber (LArTPC) for the DUNE Far Detector. The volume of data collected by the single-phase prototype (protoDUNE-SP) amounts to 3PB and the sustained rate of data sent to mass storage is O(100) MB/s. Data Quality Monitoring was implemented by directing a fraction of the data stream to the protoDUNE prompt processing system (p3s) which is optimized for continuous low-latency calculation of the vital detector metrics and various graphics including event displays. It served a crucial role throughout the life cycle of the experiment. We present our experience in leveraging the CERN computing environment and operating the system over an extended period of time, while adapting to evolving requirements and computing platform.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗