Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Crystallographic analysis of rock grain orientation at meso- and microscale levels

This paper studies the results of electron backscatter diffraction analysis of naturally deformed polycrystalline olivine. It also defines the dependence of lattice-preferred orientations of grains on their microstructural position and size. The authors detect the basic mechanisms, consequence and thermal dynamic modes of deformation. They also show that the development of a polycrystalline structure is determined by the following consecutive activation of sliding systems (010)[100] → (0kl)[100] → (100)[010] → (100)[001] → (110)[001], when dislocation sliding and diffusion creep change under the temperature decrease from 1000°C to 650°C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Breatherlike defects and their dynamics in the one-dimensional roll structure of twisted nematics

The dynamics of the nonsingular defects in the periodic structures of the rolls that appear in π/2-twisted nematic liquid crystals during electroconvection is studied experimentally and theoretically. The roll structures in twisted nematics are characterized by the presence of an axial component of the hydrodynamic flow velocity with opposite directions in neighboring rolls. The critical oscillation frequency of structural defects is quantitatively estimated using a nonlinear equation of motion for roll displacements. It is found that a pair of edge dislocations with topological charges of +1 and–1 nucleates and annihilates periodically during the oscillations of a defect with a nonsingular core. Oscillating defects with a zero topological charge is shown to correspond to the solution of the sine-Gordon equation in the form of standing breathers. Asymmetry is detected in the full oscillation cycle of a breather defect, and it is related to the twist symmetry of a twist nematic. This asymmetry is taken into account as effective anisotropic friction. The behavior of a breather on a trap, namely, a classical defect (dislocation), is investigated. Dislocation motion is shown to be anisotropic in the oscillation cycle: in one direction, a dislocation moves regularly; in the second phase, the transition into the initial state proceeds via the decay of the breather into a dipole pair of dislocations of opposite signs followed by their annihilation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Development of high-efficiency solar cells on silicon web

Work was performed to improve web base material with a goal of obtaining solar cell efficiencies in excess of 18% (AM1). Efforts in this program are directed toward identifying carrier loss mechanisms in web silicon, eliminating or reducing these mechanisms, designing a high efficiency cell structure with the aid of numerical models, and fabricating high efficiency web solar cells. Fabrication techniques must preserve or enhance carrier lifetime in the bulk of the cell and minimize recombination of carriers at the external surfaces. Three completed cells were viewed by cross-sectional transmission electron microscopy (TEM) in order to investigate further the relation between structural defects and electrical performance of web cells. Consistent with past TEM examinations, the cell with the highest efficiency (15.0%) had no dislocations but did have 11 twin planes.

Meier, D. L.↗

Study of Etching Pits in a Large-grain Single Cell Bulk Niobium Cavity

Performance of SRF cavities are limited by non-linear localized effects. The variation of local material characters between "hot" and "cold" spots is thus of intense interest. Such locations were identified in a BCP-etched large-grain single-cell cavity and removed for examination by high resolution electron microscopy (SEM), electron-back scattering diffraction microscopy (EBSD), optical microscopy, and 3D profilometry. Pits with clearly discernable crystal facets were observed in both "hotspot" and "coldspot" specimens. The pits were found in-grain, at bi-crystal boundaries, and on tri-crystal junctions. They are interpreted as etch pits induced by surface crystal defects (e.g. dislocations). All "coldspots" examined had qualitatively low density of etching pits or very shallow tri-crystal boundary junction. EBSD revealed crystal structure surrounding the pits via crystal phase orientation mapping, while 3D profilometry gave information on the depth and size of the pits. In addition, a survey of the samples by energy dispersive X-ray analysis (EDX) did not show any significant contamination of the samples surface.

36 MATERIALS SCIENCE↗

Deformation and failure in extreme regimes by high-energy pulsed lasers: A review

The use of high-power pulsed lasers to probe the response of materials at pressures of hundreds of GPa up to several TPa, time durations of nanoseconds, and strain rates of 10 6 –10 1° s -1 is revealing novel mechanisms of plastic deformation, phase transformations, and even amorphization. This unique experimental tool, aided by advanced diagnostics, analysis, and characterization, allows us to explore these new regimes that simulate those encountered in the interiors of planets. Fundamental Materials Science questions such as dislocation velocity regimes, the transition between thermally-activated and phonon drag regimes, the slip-twinning transition, the ultimate tensile strength of metals, the dislocation mechanisms of void growth are being answered through this powerful tool. In parallel with experiments, molecular dynamics simulations provide modeling and visualization at comparable strain rates (10 8 –10 10 s -1 ) and time durations (hundreds of picoseconds). Finally, this powerful synergy is illustrated in our past and current work, using representative face-centered cubic (fcc) copper, body-centered cubic (bcc) tantalum and diamond cubic silicon as model structures.

36 MATERIALS SCIENCE↗

Correlation between switching to n-type conductivity and structural defects in highly Mg-doped InN

The effect of Mg doping on the microstructure of InN epitaxial films in relation to their free-charge carrier properties has been investigated by transmission electron microscopy (TEM) and aberration corrected scanning TEM. We observe a direct correlation between Mg concentration and the formation of stacking faults. The threading dislocation density is found to be independent of Mg concentration. The critical Mg concentration for the on-set of stacking faults formation is determined and found to correlate with the switch from p- to n-type conductivity in InN. Potential mechanisms involving stacking faults and point defect complexes are invoked in order to explain the observed conductivity reversal. Finally, the stacking faults are structurally determined and their role in the reduction of the free electron mobility in highly doped InN:Mg is discussed.

36 MATERIALS SCIENCE↗

Intragranular cracking as a critical barrier for high-voltage usage of layer-structured cathode for lithium-ion batteries

LiNi 1/3 Mn 1/3 Co 1/3 O 2 (NMC333) layered cathode is often fabricated as secondary particles of consisting of densely packed primary particles, which offers advantage of high energy density and alleviation of cathode side reactions/corrosions, but introduces other drawbacks, such as intergranular cracking. Here, we report unexpected observations on the nucleation and growth of intragranular cracks in the commercial NMC333 layered cathode by using advanced S/TEM. We found that the formation of the intragranular cracks is directly associated with high voltage cycling, which is an electrochemically driven and diffusion controlled process. The intragranular cracks were noticed to be characteristically initiated from grain interior, a consequence of dislocation based crack incubation mechanism. This observation is in sharp contrast with the general theoretical models, predicting the initiation of intragranular cracks from grain boundaries or particle surface. As a result, our study indicates that maintain a structural stability is the key step toward high voltage operation of layered cathode materials.

25 ENERGY STORAGE↗

Energy Expenditure Upon the Formation of the Elastically Stressed State in the Layers of a Step-Graded Metamorphic Buffer in a Heterostructure Grown on a (001) GaAs Substrate

On the basis of data on X-ray structural analysis performed by the method of reciprocal-space mapping and investigations using secondary-ion mass spectrometry and transmission electron microscopy, it is shown that vertical compressive stresses also arise in a multilayer epitaxial heterostructure comprised of a step-graded metamorphic buffer along with lateral compressive stresses. The cause of the appearance of vertical stresses is the effect of interlayer hardening, which arises due to the deceleration of fragments of glide dislocations by interphase boundaries. Analysis performed within the framework of the linear theory of elasticity shows that the elastically stressed state of the buffer steps is similar to the state that can be achieved as a result of a two-stage deformation process: bulk and biaxial compression. Bulk compression leads to large energy expenditures in the formation of the structure of the buffer steps, which is reflected, in particular, in violation of the coherence between the dislocation-free and the underlying layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evolution of dislocation substructures in metals via high-strain-rate nanoindentation

Deformation at high strain rates often results in high stresses on many engineering materials, potentially leading to catastrophic failure without proper design. High-strain-rate mechanical testing is thus needed to improve the design of future structural materials for a wide range of applications. Although several high-strain-rate mechanical testing techniques have been developed to provide a fundamental understanding of material responses and microstructural evolution under high-strain-rate deformation conditions, these tests are often very time consuming and costly. In this work, we utilize a high-strain-rate nanoindentation testing technique and system in combination with transmission electron microscopy to reveal the deformation mechanisms and dislocation substructures that evolve in pure metals from low (10 –2 s –1 ) to very high indentation strain rates (10 4 s –1 ), using face-centered cubic aluminum and body-centered cubic molybdenum as model materials. The results help to establish the conditions under which micro- and macro-scale tests can be compared with validity and also provide a promising pathway that could lead to accelerated high-strain-rate testing at substantially reduced costs.

36 MATERIALS SCIENCE↗

Growth mechanisms, polytypism, and real structure of kaolinite microcrystals

The mechanisms of growth of kaolinite microcrystals (0.1-5.0 {mu}m in size) at deposits related to the cluvial weathering crust, as well as to the low-temperature and medium-temperature hydrothermal processes of transformations of minerals in different rocks in Russia, Kazakhstan, Ukraine, Czechia, Vietnam, India, Cuba, and Madagascar, are investigated using transmission electron microscopy and vacuum decoration with gold. It is established that kaolinite microcrystals grow according to two mechanisms: the mechanism of periodic formation of two-dimensional nuclei and the mechanism of spiral growth. The spiral growth of kaolinite microcrystals is dominant and occurs on steps of screw dislocations that differ in sign and magnitude of the Burgers vector along the c axis. The layered growth of kaolinite originates from a widespread source in the form of a step between polar (+ and -) dislocations, i.e., a growth analogue of the Frank-Read dislocation source. The density of growth screw dislocations varies over a wide range and can be as high as {approx}10{sup 9} cm{sup -2}. Layered stepped kaolinite growth pyramids for all mechanisms of growth on the (001) face of kaolinite exhibit the main features of the triclinic 1Tc and real structures of this mineral.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Epitaxial growth of fcc-Co{sub x}Ni{sub 100-x} thin films on MgO(110) single-crystal substrates

Co{sub x}Ni{sub 100-x} (x=100, 80, 20, 0 at. %) epitaxial thin films were prepared on MgO(110) single-crystal substrates heated at 300 deg. C by ultrahigh vacuum molecular beam epitaxy. The growth mechanism is discussed based on lattice strain and crystallographic defects. CoNi(110) single-crystal films with a fcc structure are obtained for all compositions. Co{sub x}Ni{sub 100-x} film growth follows the Volmer-Weber mode. X-ray diffraction analysis indicates that the out-of-plane and the in-plane lattice spacings of the Co{sub x}Ni{sub 100-x} films are in agreement within +-0.5% with the values of the respective bulk Co{sub x}Ni{sub 100-x} crystals, suggesting that the strain in the film is very small. High-resolution cross-sectional transmission microscopy shows that an atomically sharp boundary is formed between a Co(110){sub fcc} film and a MgO(110) substrate, where periodical misfit dislocations are preferentially introduced in the film at the Co/MgO interface. The presence of such periodical misfit dislocations relieves the strain caused by the lattice mismatch between the film and the substrate.

36 MATERIALS SCIENCE↗

Graded microstructure and mechanical properties of spark plasma sintered Fe-Cr alloys

Developing graded microstructure and mechanical properties is critical for accelerating the design and optimization of structural materials for a wide range of applications. Here, in this study, Fe-Cr alloys were fabricated by spark plasma sintering (SPS) technique. The microstructure, microhardness, and tensile properties of the as-fabricated and thermally annealed variants were investigated. Graded grain structures were created in the as-fabricated cylinders along both axial and radial directions. Grain size was gradually reduced from the sample periphery to the center. Microhardness measurements reveal a gradual decrease of hardness towards the periphery of the samples. The as-fabricated Fe-Cr alloys show a desired combination of tensile strength and elongation, primarily due to the formation of a high density of oxides, voids, dislocations, and grain boundaries. After in-situ thermal annealing at 600 °C under 60 MPa for 2 h using SPS, the Fe-Cr alloys underwent minimal grain growth, and the graded grain structures were retained. The hardness was more uniformly distributed in the annealed variants, and the tensile strength was reduced with an increase in the total elongation, which is attributed to the dissolution of nano-sized oxide particles and the relief of the residual stress. This study demonstrates that SPS coupled with subsequent heat treatment can tailor the graded microstructure and control the mechanical properties of Fe-Cr alloys, showing potential applications in other alloy systems.

36 MATERIALS SCIENCE↗

Optical performance of top-down fabricated InGaN/GaN nanorod light emitting diode arrays

Vertically aligned InGaN/GaN nanorod light emitting diode (LED) arrays were created from planar LED structures using a new top-down fabrication technique consisting of a plasma etch followed by an anisotropic wet etch. The wet etch results in straight, smooth, well-faceted nanorods with controllable diameters and removes the plasma etch damage. 94% of the nanorod LEDs are dislocation-free and a reduced quantum confined Stark effect is observed due to reduced piezoelectric fields. Despite these advantages, the IQE of the nanorod LEDs measured by photoluminescence is comparable to the planar LED, perhaps due to inefficient thermal transport and enhanced nonradiative surface recombination.

42 ENGINEERING↗

In-Situ SEM High Strain Rate Testing of Large Diameter Micropillars Followed by TEM and EBSD Postmortem Analysis

Background Dislocation dynamic simulations are intended as a tool to understand and predict the mechanical behavior of metallic materials, but its prediction has never been directly verified by experiments due to differences in specimen strain rate and size. Objective In this work, a comprehensive experimental framework is proposed to attempt direct comparison between experiments and discrete dislocation dynamics (DDD) modelling. Methods By integrating high-throughput sample fabrication and a customized testing apparatus, the sample size and strain rate typically employed in DDD simulations are explored experimentally. Constitutive properties such as stress-strain response are measured, and microstructural information is obtained from transmission electron microscopy (TEM) imaging, electron backscatter diffraction (EBSD), and TEM-based orientation mapping. Results Magnesium and copper were selected, as case studies, to demonstrate the newly developed experimental procedure. Measured stress-strain responses for Mg are consistent with those obtained with a miniaturized Hopkison bar experiments. Furthermore, by exploiting the validated workflow, the effect of strain rate on micropillar heterogeneous deformation and associated dislocation plasticity were revealed. Conclusion The work establishes a methodology for the systematic study of not only metals but also other materials and structures at the microscale and high strain rates.

42 ENGINEERING↗

High strength and high ductility in a novel Fe 40.2 Ni 11.3 Mn 30 Al 7.5 Cr 11 multiphase high entropy alloy

In the present study, a novel Fe 40.2 Ni 11.3 Mn 30 Al 7.5 Cr 11 high entropy alloy displaying an excellent com- bination of high strength and high ductility has been developed. The b.c.c.þB2/f.c.c. dendritic- interdendritic microstructure was characterized using scanning electron microscopy, X-ray diffraction, and transmission electron microscopy, and the alloy’s mechanical properties were examined using Vickers hardness measurements and room-temperature tensile tests. The phase stability of Fe 40.2 Ni 11.3 Mn 30 Al 7.5 Cr 11 was investigated by annealing the alloy between 1173 Ke1273 K, and the presence of both Ni-rich, b.c.c. needle-shaped precipitates and Cr-rich, s phase particles was observed for the 1173 K annealed specimen. The s phase precipitates contributed to the rapid age-hardening effect in the material annealed at 1173 K. A further increase in ageing temperature to 1223 K and 1273 K led to the dissolution of the s phase and a reduction in the volume fraction of the b.c.c./B2 dendrites, which led to a consequent drop in room-temperature yield strength from the as-cast value of ~593 MPae~486 MPa and ~228 MPa for the specimens annealed at 1223 K and 1273 K, respectively. An accompanying increase in ductility was observed from ~22% for the as-cast alloy to ~27% and ~40% after annealing the material at 1223 K and 1273 K, respectively. Post-deformation transmission electron micrographs revealed that the f.c.c interdendrites accommodated plastic strain via wavy slip and moreover, deformed before the b.c.c. dendritic regions, which were reinforced by B2 particles and acted as obstacles to moving dislocations. Finally, the discovery of a multi-phase HEA that contains 11% Cr and good mechanical properties has relevant high-temperature structural applications especially in cases that require suitable corrosion resistance.

36 MATERIALS SCIENCE↗

A microscopic continuum model for defect dynamics in metallic glasses

Motivated by results of the topological theory of glasses accounting for geometric frustration, here we develop the simplest possible continuum mechanical model of defect dynamics in metallic glasses that accounts for topological, energetic, and kinetic ideas. A geometrical description of ingredients of the structure of metallic glasses using the concept of local order based on Frank–Kasper phases and the notion of disclinations as topological defects in these structures is proposed. This novel kinematics is incorporated in a continuum mechanical framework capable of describing the interactions of disclinations and also of dislocations (interpreted as pairs of opposite disclinations). The model is aimed towards the development of a microscopic understanding of the plasticity of such materials. We discuss the expected predictive capabilities of the model vis-a-vis some observed physical behaviors of metallic glasses.

36 MATERIALS SCIENCE↗

Strain induced grain boundary migration effects on grain growth of an austenitic stainless steel during static and metadynamic recrystallization

Static and metadynamic recrystallization of an AISI 304L austenitic stainless steel was investigated at 1100 °C and 10{sup −} {sup 2} s{sup −} {sup 1} strain rate. The kinetics of recrystallization was determined through double hit compression tests. Two strain levels were selected for the first compression hit: ε{sub f} = 0.15 for static recrystallization (SRX) and 0.25 for metadynamic recrystallization (MDRX). Both the as-deformed and the recrystallized microstructures were investigated through optical microscopy and electron back-scattered diffraction (EBSD) technique. During deformation, strain induced grain boundary migration appeared to be significant, producing a square-like grain boundary structure aligned along the directions of the maximum shear stresses in compression. EBSD analysis revealed to be as a fundamental technique that the dislocation density was distributed heterogeneously in the deformed grains. Grain growth driven by surface energy reduction was also investigated, finding that it was too slow to explain the experimental data. Based on microstructural results, it was concluded that saturation of the nucleation sites occurred in the first stages of recrystallization, while grain growth driven by strain induced grain boundary migration (SIGBM) dominated the subsequent stages. - Highlights: • Recrystallization behavior of a stainless steel was investigated at 1100 °C. • EBSD revealed that the dislocation density distribution was heterogeneous during deformation. • Saturation of nucleation sites occurred in the first stages of recrystallization. • Strain induced grain boundary migration (SIGBM) effects were significant. • Grain growth driven by SIGBM dominated the subsequent stages.

36 MATERIALS SCIENCE↗

A high-performance β-solidifying TiAl alloy sheet: Multi-type lamellar microstructure and phase transformation

Highlights: • A high-performance β-solidifying TiAl alloy sheet is fabricated via hot rolling. • Fine multi-type β/γ and α{sub 2}/γ lamellar structures are formed during hot-rolling. • These lamellar structures are induced by the β → γ and α + γ → α{sub 2} + γ/γ{sub T} transformations. • The nano-scaled antiphase domain is induced by α → α{sub 2} disorder-order transformation. • The fine multi-type lamellar structures contribute to the strength enhancement. - Abstract: TiAl alloys are widely used in the aerospace industry and, hence, a thorough understanding of the corresponding microstructural evolution is crucial for providing insight into the fabrication of high-performance TiAl alloy sheets. In this study, a high-performance β-solidifying Ti-43Al-9V-0.2Y alloy sheet with multi-type lamellar structures was obtained via hot-rolling at an initial rolling temperature of 1260 °C. Owing to the temperature drop and reheat associated with multi-pass rolling, relatively fine irregular β/γ and regular α{sub 2}/γ lamellar microstructures (average size: ~25 μm) with nano-scaled antiphase domains (APDs) were generated by the β → γ and α + γ → α{sub 2} + γ/γ{sub T} phase transformations. These two lamellar structures have different formation mechanisms. The results of electron backscatter diffraction and transmission electron microscopy revealed that the nucleation and growth of (i) β/γ and (ii) α{sub 2}/γ lamellar structures are induced mainly by (i) stress and (ii) a combination of the stress and temperature drop during hot-rolling, respectively. Thin γ{sub T} precipitates from the α/α{sub 2} or γ phases. This precipitation is induced by the higher stress and lower temperature associated with the later stage (compared with those occurring in the initial stages) of hot-rolling. Moreover, compared with the corresponding as-forged alloy, the as-rolled TiAl alloy sheet exhibits better performance at both room and elevated temperatures. The improvement in the tensile properties is attributed to the duplex microstructure consisting of fine multi-type lamellar structures with nano-scaled APDs. The interface boundaries of β/γ, α{sub 2}/γ and APDs, which are effective in retarding dislocation motion, contribute mainly to strengthening of the alloy sheet.

36 MATERIALS SCIENCE↗