Search NASA⌕ Search

SEARCH · Search NASA

Results for “Homogeneous flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Use of a Heat Flow Meter to Determine Active PCM Content in an Insulation

Residential and commercial roofs and walls are currently designed and tested using steady-state criteria. The resulting R-values, based on the apparent thermal conductivity, are used by building standards as an important measure of energy performance. Building envelope components, however, are subject to dynamic environmental conditions. This mismatch between the steady-state principles used in design and code requirements and their dynamic operation results in relatively low thermal efficiencies. Although several research centers have developed experimental methods for transient analysis of building envelopes, there are no standardized testing procedures available for screening materials and systems for which performance depends on dynamic response. For example, a full-scale dynamic evaluation of phase change materials (PCMs) is needed to assess their energy saving benefits. A nationally accepted small-scale (one to two foot size specimens) testing procedure is not available for the analysis of dynamic thermal characteristics of conventional thermal mass systems or PCM-enhanced materials. At the same time, data on these characteristics are necessary for whole-building simulations, energy analysis, and energy code work. The transient characteristics of PCM-enhanced products depend on the PCM content and quality. The only readily available method of thermal evaluation uses the differential scanning calorimeter. Unfortunately, this method requires small, relatively uniform test specimens. This requirement is unrealistic in the case of PCM-enhanced building envelope products such as PCM-cellulose, PCM-glass fiber, or PCM-gypsum blends. Small specimens are not representative of PCM-based blends, since these materials are not homogeneous. Jan Kosny and David Yarbrough, Oak Ridge National Laboratory, P.O. Box 2008, MS 6070, Oak Ridge, TN 37831-6070. Elizabeth Kossecka, Polish Academy of Sciences, Institute of Fundamental Technological Research, Pawinskiego 5 B, 02-106, Warsaw, Poland. A procedure for making dynamic heat-flow measurements using existing instrumentation has been developed to analyze the benefits of thermal storage. This small-scale testing method is useful for thermal analysis and as a potential quality control method for producers of PCM-enhanced building materials. The research may provide the basis for consensus standard development. This paper uses as an example a dynamic testing process for PCM-enhanced cellulose insulation.

25 ENERGY STORAGE↗

Rapid Distortion Theory for Compressible Homogeneous Turbulence Under Isotropic Mean Strain

The case of isotropic compressible turbulence subjected to rapid isotropic compression is studied using inviscid rapid distortion theory and direct numerical simulation. An exact solution to the rapid distortion problem is given, and results are compared to those of direct numerical simulation. Implications for modelling turbulent flows are discussed.

Blaisdell, G. A.↗

The Cauchy Problem for Boltzmann Bi-linear Systems: The Mixing of Monatomic and Polyatomic Gases

Abstract From a unified vision of vector valued solutions in weighted Banach spaces, this paper establishes the existence and uniqueness for space homogeneous Boltzmann bi-linear systems with conservative collisional forms arising in complex gas dynamical structures. This broader vision is directly applied to dilute multi-component gas mixtures composed of both monatomic and polyatomic gases. Such models can be viewed as extensions of scalar Boltzmann binary elastic flows, as much as monatomic gas mixtures with disparate masses and single polyatomic gases, providing a unified approach for vector valued solutions in weighted Banach spaces. Novel aspects of this work include developing the extension of a general ODE theory in vector valued weighted Banach spaces, precise lower bounds for the collision frequency in terms of the weighted Banach norm, energy identities, angular or compact manifold averaging lemmas which provide coerciveness resulting into global in time stability, a new combinatorics estimate for p -binomial forms producing sharper estimates for the k -moments of bi-linear collisional forms. These techniques enable the Cauchy problem improvement that resolves the model with initial data corresponding to strictly positive and bounded initial vector valued mass and total energy, in addition to only a $$2^+$$ 2 + moment determined by the hard potential rates discrepancy, a result comparable in generality to the classical Cauchy theory of the scalar homogeneous Boltzmann equation.

Physics↗

Enhancing the Melt Strength of Poly(Lactic Acid) via Micro-Crosslinking and Blending with Poly(Butylene Adipate-co-Butylene Terephthalate)for the Preparation of Foams

The melt strength of poly(lactic acid) (PLA) is an important factor in preparing foams and blowing films. Aiming to endow PLA with a suitable melt strength via a slight crosslink, a superficial micro-crosslinking method was introduced in which the PLA feed was mixed with benzoyl peroxide (BPO) and crosslinked in a 100 °C oven for 1 h. Additionally, poly(butyleneadipate-co-terephthalate) (PBAT) was blended with the crosslinked PLA (C-PLA) to further improve melt strength and viscosity. The blend foams were prepared using a single-screw extruder and azodicarbonamide as a foaming agent. The properties were characterized by gel fraction, melt flow rate (MFR), rheometry, DSC and SEM. The rheological results showed that the complex viscosity and storage modulus of C-PLA and C-PLA/PBAT blends increased, attributed to the micro-crosslinking and addition of PBAT and indicating an improvement in melt strength. Furthermore, the crystallization of modified PLA was also enhanced. Compared with pure PLA foams, the C-PLA/PBAT blend foams showed larger cells with more uniform shapes and homogenous distribution. This approach to improve the melt strength of polymers with micro-crosslinking and blending with PBAT represents an attractive method for preparing foams with regular cells.

36 MATERIALS SCIENCE↗

Application of SPH Factors to PHWR Lattice Homogenization

Pressurized Heavy-Water Reactors (PHWRs) are heavy-water moderated and cooled. They consist of a horizontal, cylindrical, non-pressurized calandria vessel which contains the heavy-water moderator and is penetrated axially by fuel channels. Fuel channels consist of two concentric tubes separated by a gas gap: an inner tube called the pressure tube, and an outer tube called the calandria tube. The pressure tubes hold the fuel bundles, which are cooled by the flow of coolant at high temperature and pressure. The coolant flows in opposite directions in adjacent channels. The gap between the pressure and calandria tubes ensures that the temperature of the moderator remains relatively low, below 80 deg. C. For a CANDU 6 reactor, there are 380 fuel channels, each holding 12 37-element fuel bundles, approximately 10-cm in diameter and 50-cm long each. The fuel pins are arranged in three concentric rings (consisting of 6, 12 and 18 pins respectively), plus a central pin. The distance between channels (lattice pitch) is approximately 28.6 cm. Production core-level neutronics calculations are usually performed in a Cartesian geometry using few group diffusion and a simplified core model, whereby neutronics properties are homogenized over large regions called nodes. For Light Water reactors (LWRs), the two-dimensional axial (x-y) projection of a node corresponds to one fuel assembly. For PHWRs, a node usually consists of one fuel bundle and its associated moderator. For LWRs, advanced core-level calculations based on advanced node-level homogenization methods, such as Generalized Equivalence Theory (GET) or Super-homogenisation (SPH), improve the accuracy of full-core calculations compared to - standard homogenization. For rectangular fuel-pin arrangements, SPH can be used to perform pin-cell level homogenization which allows subsequent core-level diffusion calculations to be performed using fine Cartesian meshes. For PHWRs, the distribution of fuel pins in concentric rings makes the use of Cartesian mesh refinement impractical. However, SPH can still be applied, albeit using a coarser node subdivision, by dividing the heterogeneous node into 3x3 sub-regions in such a way that the central sub-region includes the entire fuel channel. This work investigates the use of SPH homogenization using a 3x3 subdivision of the PHWR node. Preliminary results show that the use of SPH factors does not yield more accurate results than standard homogenization when applied to PHWR nodes using a 3x3 subdivision. The explanation appears to lie in the fact that SPH factors are dependent on node-boundary leakage. Future investigations to confirm the leakage-dependence of SPH factors are recommended. Accuracy improvements may also be achievable by using smaller SPH regions at the periphery of the PHWR node, in an attempt to reduce the SPH factors' dependence on node-boundary leakage. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

LSENS, a general chemical kinetics and sensitivity analysis code for gas-phase reactions: User's guide

A general chemical kinetics and sensitivity analysis code for complex, homogeneous, gas-phase reactions is described. The main features of the code, LSENS, are its flexibility, efficiency and convenience in treating many different chemical reaction models. The models include static system, steady, one-dimensional, inviscid flow, shock initiated reaction, and a perfectly stirred reactor. In addition, equilibrium computations can be performed for several assigned states. An implicit numerical integration method, which works efficiently for the extremes of very fast and very slow reaction, is used for solving the 'stiff' differential equation systems that arise in chemical kinetics. For static reactions, sensitivity coefficients of all dependent variables and their temporal derivatives with respect to the initial values of dependent variables and/or the rate coefficient parameters can be computed. This paper presents descriptions of the code and its usage, and includes several illustrative example problems.

Radhakrishnan, Krishnan↗

Wire-Wrapped Fuel Pin Effect of Bundle Size on Temperature Distribution for Uniform Heat Flux

A common fuel arrangement for Sodium Fast Reactors (SFR) designs are hexagonal arrays of wire wrapped fuel pins. The helically wound wires redirect coolant to neighboring subchannels and increases mixing. The increased mixing of the coolant is beneficial to heat transfer from the fuel and prevents temperature peaking in hot channels that may occur. The purpose of this study is to observe the effect of bundle size on the temperature distribution of a coolant when a constant heat flux is implemented. Bundles of 19, 37, 61, and 91 pins were modeled. The wire-wrapping on fuel pins encourages interchannel mixing. With a constant heat flux the enhanced interchannel mixing has little observable effect. The temperature distributions of the subchannels has negligible dependence on radial or angular position. The temperature distribution additionally shows negligible dependence on the bundle size. The subchannel average temperatures further illustrate the homogeneity of the temperature across the bundles. Similarly oriented subchannels differ by less than two Kelvin. The temperature distribution within a single subchannel is fairly uniform, differing by about 15 K between the wall and the bulk flow, with the exception of two hot spots. The two hot spots, however, occur in two non-geometrically accurate locations, so little analysis can be performed. To better illustrate the effect of the enhanced mixing of the wire-wrapped fuel pins, a hot pin analysis should be performed to observe how the additional, non-uniform heat is dispersed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Subsurface microbial communities as a tool for characterizing regional-scale groundwater flow

Subsurface microbial community distribution patterns are influenced by biogeochemical and groundwater fluxes and may inform hydraulic connections along groundwater-flow paths. This study examined the regional-scale microbial community of the Death Valley Regional Flow System and evaluated whether subsurface communities can be used to identify groundwater-flow paths between recharge and discharge areas. Samples were collected from 36 sites in three groundwater basins: Pahute Mesa–Oasis Valley (PMOV), Ash Meadows (AM), and Alkali Flat–Furnace Creek Ranch (AFFCR). Microbial diversity within and between communities varied by location, and communities were separated into two overall groups that affiliated with the AM and PMOV/AFFCR basins. Network analysis revealed patterns between clusters of common microbes that represented groundwaters with similar geochemical conditions and largely corroborated hydraulic connections between recharge and discharge areas. Null model analyses identified deterministic and stochastic ecological processes contributing to microbial community assemblages. Most communities were more different than expected and governed by dispersal limitation, geochemical differences, or undominating processes. However, certain communities from sites located within or near the Nevada National Security Site were more similar than expected and dominated by homogeneous dispersal or selection. Overall, the (dis)similarities between the microbial communities of DVRFS recharge and discharge areas supported previously documented hydraulic connections between: (1) Spring Mountains and Ash Meadows; (2) Frenchman and Yucca Flat and Amargosa Desert; and (3) Amargosa Desert and Death Valley. However, only a portion of the flow path between Pahute Mesa and Oasis Valley could be supported by microbial community analyses, likely due to well-associated artifacts in samples from the two Oasis Valley sites. This study demonstrates the utility of combining microbial data with hydrologic, geologic, and water-chemistry information to comprehensively characterize groundwater systems, highlighting both strengths and limitations of this approach.

54 ENVIRONMENTAL SCIENCES↗

Enhanced ATAMM for increased throughput performance of multicomputer data flow architectures

The Algorithm To Architecture Mapping Model (ATAMM) is a Petri-net-based model which provides a strategy for periodic execution of a class of real-time algorithms on multicomputer dataflow architectures. The problem domain of particular interest is the execution of large-grained, decision-free algorithms on homogeneous processing elements. Design techniques are discussed and performance measurements are defined. A multiple-graph execution strategy is shown to increase throughput performance. It is shown that the same increase in performance is attainable with minor modifications to the existing ATAMM.

Jones, R. L.↗

Modeling of internal and near-nozzle flow for a GDI fuel injector

A numerical study of two-phase flow inside the nozzle holes and the issuing spray jets for a multi-hole direct injection gasoline injector has been presented in this work. The injector geometry is representative of the Spray G nozzle, an eight-hole counterbore injector, from the Engine Combustion Network (ECN). Simulations have been carried out for a fixed needle lift. Effects of turbulence, compressibility and non-condensable gases have been considered in this work. Standard k -ε turbulence model has been used to model the turbulence. Homogeneous Relaxation Model (HRM) coupled with Volume of Fluid (VOF) approach has been utilized to capture the phase change phenomena inside and outside the injector nozzle. Three different boundary conditions for the outlet domain have been imposed to examine non-flashing and evaporative, non-flashing and non-evaporative and flashing conditions. Noticeable hole-to-hole variations have been observed in terms of mass flow rates for all the holes under all the operating conditions considered in this study. Inside the nozzle holes mild cavitation-like and in the near-nozzle region flash boiling phenomena have been predicted when liquid fuel is subjected to superheated ambiance. Under favorable conditions considerable flashing has been observed in the near-nozzle regions. An enormous volume is occupied by the gasoline vapor, stantial computational cost. Volume-averaging instead of mass-averaging is observed to be more effective, especially for finer mesh resolutions.

42 ENGINEERING↗

A method of calculating the total flow from a given sea surface topography

Using a simple dynamical model of a wind-driven ocean circulation of the Stommel type, and an analytical basis developed to objectively analyze the sea surface height residuals from an altimeter and, in the process, to determine the total flow instead of just the near surface geostrophic component associated with the given sea surface topography. The method is based on first deriving the solution to the forced problem for a given wind stress required to develop a hypothetical true or perfect data field and to establishing the basis for the objective analysis. The stream function and the surface height field for the forced problem are developed in terms of certain characteristic functions with the same expansion coefficients for both fields. These characteristic functions are simply the solutions for a homogeneous elliptic equation for the stream function and the solutions of an inhomogeneous balance equation for the height field. For the objective analysis, using a sample of randomly selected height values from the true data field, the height field characteristic functions are used to fit the given topography in a least squares sense. The resulting expansion coefficients then permit the synthesis of the total flow field via the stream function characteristic modes and the solution is perfectly well behaved even along the equator. The method of solution is easily adaptable to realistic ocean basis by straight forward numerical methods. The analytical basis of the theory and the results for an ideal rectangular basin on a beta plane are described.

Rao, Desiraju B.↗

Single- and two-phase flow in microfluidic porous media analogs based on Voronoi tessellation

The objective of this study was to create a microfluidic model of complex porous media for studying single and multiphase flows. Most experimental porous media models consist of periodic geometries that lend themselves to comparison with well-developed theoretical predictions. However, most real porous media such as geological formations and biological tissues contain a degree of randomness and complexity that is not adequately represented in periodic geometries. To design an experimental tool to study these complex geometries, we created microfluidic models of random homogeneous and heterogeneous networks based on Voronoi tessellations. These networks consisted of approximately 600 grains separated by a highly connected network of channels with an overall porosity of 0.11 0.20. We found that introducing heterogeneities in the form of large cavities within the network changed the permeability in a way that cannot be predicted by the classical porosity-permeability relationship known as the Kozeny equation. The values of permeability found in experiments were in excellent agreement with those calculated from three-dimensional lattice Boltzmann simulations. In two-phase flow experiments of oil displacement with water we found that the surface energy of channel walls determined the pattern of water invasion, while the network topology determined the residual oil saturation. These results suggest that complex network topologies lead to fluid flow behavior that is difficult to predict based solely on porosity. The microfluidic models developed in this study using a novel geometry generation algorithm based on Voronoi tessellation are a new experimental tool for studying fluid and solute transport problems within complex porous media.

Wu, Mengjie↗

Internal Nozzle Flow Simulations of Gasoline-Like Fuels under Diesel Operating Conditions

Spray formation in internal combustion engines with direct injection is strictly correlated with internal nozzle flow characteristics, which are in turn influenced by fuel physical properties and injector needle motion. This paper pre-sents a series of 3D simulations that model the in-nozzle flow in a 5-hole mini-sac diesel injector. Two gasoline-like naphtha fuels, namely full-range and light naphtha, were tested under operating conditions typical of diesel applica-tions and were compared with n-dodecane, selected from a palette used as diesel surrogates. Validated methodolo-gies from our previous work were employed to account for realistic needle motion. The multi-phase nature of the problem was described by the mixture model assumption with the Volume of Fluid method. Cavitation effects were included by means of the Homogeneous Relaxation Model and turbulence closure was achieved with the Standard k-ε model in an Unsteady Reynolds-Averaged Navier-Stokes formulation. The results revealed that injector perfor-mance and propensity to cavitation are influenced by the fuel properties. Analyses of several physical quantities were carried out to highlight the fuel-to-fuel differences in terms of mass flow rate, discharge coefficients, and fuel vapor volume fraction inside the orifices. A series of parametric investigations was also performed to assess the fuel response to varied fuel injection temperature, injection pressure, and cross-sectional orifice area. For all cases, the strict correlation between cavitation magnitude and saturation pressure was confirmed. Owing to their higher volatil-ity, the two gasoline-like fuels were characterized by higher cavitation across all the simulated conditions. Occur-rence of cavitation was mostly found at the needle seat and at the orifice inlets during the injection event’s transient, when very small gaps exist between the needle and its seat. This behavior tended to disappear at maximum needle lift, where cavitation was absent for all fuels. Differences in mass flow rate between the naphtha fuels and n-dodecane were measured and ascribed to the different densities of the three fuels. Nevertheless, they were found to be smaller than expected, owing to the lower viscosity of the gasoline-like fuels. This beneficial influence of the lower viscosity was shown to be less effective at higher temperature, where the relative viscosity differences de-creased.

Torelli, R.↗

Digital image processing of flow visualization photographs

This paper is concerned with the propagation of laser light through a slab of a randomly varying medium. A theoretical analysis is presented which relates the spectrum of the recorded-intensity field some distance downstream of the medium to the spectrum of the index-of-refraction field. For a homogeneous and isotropic random field, the 3-D spectrum of the medium is obtained from the 2-D spectrum of the photograph by dividing each component of the spectrum by the frequency raised to the fourth power. Free-space propagation outside the random medium is accounted for by a scaling factor. Experimental results are presented which support the theoretical analysis. The nonintrusive diagnostic technique presented here is applicable to photographs which contain partially developed caustic networks.

Hesselink, L.↗

Multiscale Investigation on Biofilm Distribution and Its Impact on Macroscopic Biogeochemical Reaction Rates

Biofilms are critical locations for biogeochemical reactions in the subsurface environment. The occurrence and distribution of biofilms at microscale as well as their impacts on macroscopic biogeochemical reaction rates are still poorly understood. This paper investigated the formation and distributions of biofilms in heterogeneous sediments using multiscale models, and evaluated the effects of biofilm heterogeneity on local and macroscopic biogeochemical reaction rates. Sediment pore structures derived from X-ray computed tomography were used to simulate the microscale flow dynamics and biofilm distribution in the sediment column. The response of biofilm formation and distribution to the variations in hydraulic and chemical properties was first examined. One representative biofilm distribution was then utilized to evaluate its effects on macroscopic reaction rates using nitrate reduction as an example. The results revealed that microorganisms primarily grew on the surfaces of grains and aggregates near preferential flow paths where both electron donor and acceptor were readily accessible, leading to the heterogeneous distribution of biofilms in the sediments. Furthermore, the heterogeneous biofilm distribution decreased the macroscopic rate of biogeochemical reactions as compared with those in homogeneous cases. Operationally considering the heterogeneous biofilm distribution in macroscopic reactive transport models such as using dual porosity domain concept can significantly improve the prediction of biogeochemical reaction rates. Overall, this study provided important insights into the biofilm formation and distribution in soils and sediments as well as their impacts on the macroscopic manifestation of reaction rates.

42 ENGINEERING↗

Development of Geomechanical Screening Tools to Identify Risk: An Experimental and Modeling Approach for Secure CO 2 Storage Final Technical Report

CO 2 injection in the subsurface introduces additional complexity in terms of interactions of the reservoir host pore fluid with natural heterogeneity of hydro-mechanical properties of the rock. Natural heterogeneity of the reservoir rock and caprock formations includes spatial variation of hydro-mechanical properties as well as the presence of natural fractures. We developed a coupled mathematical modeling and experimental framework that takes into account the effect of rock heterogeneity on effective mechanical properties of the rock in contact with CO 2 . We performed accurate laboratory experiments to determine the changes in rock mechanical properties due to mineral dissolution in the presence of carbonic acid generated by CO 2 injection. A two-scale adaptive homogenization framework was then developed to consistently upscale petrophysical and geomechanical properties to the field scale. Further, we also developed high-fidelity, numerical solution schemes, non-linear and linear solvers and preconditioners to solve the coupled flow, reactive transport and geomechanical system. The numerical model was then used to study field scale CO 2 sequestration problems for the two selected field sites: (1) Frio formation and (2) Cranfield site. We also developed robust schemes for field data assimilation, model calibration such that the residual uncertainty at the end of the data assimilation procedures can be faithfully represented while taking into account the coupled geochemical and geomechanical processes.

42 ENGINEERING↗

Physics-Driven Convolutional Autoencoder Approach for CFD Data Compressions: Preprint

With the growing size and complexity of turbulent flow models, data compression approaches are of the utmost importance to analyze, visualize, or restart the simulations. Recently, in-situ autoencoder-based compression approaches have been proposed and shown to be effective at producing reduced representations of turbulent flow data. However, these approaches focus solely on training the model using point-wise sample reconstruction losses that do not take advantage of the physical properties of turbulent flows. In this paper, we show that training autoencoders with additional physics-informed regularizations, e.g., enforcing incompressibility and preserving enstrophy, improves the compression model in three ways: (i) the compressed data better conform to known physics for homogeneous isotropic turbulence without negatively impacting point-wise reconstruction quality, (ii) inspection of the gradients of the trained model uncovers changes to the learned compression mapping that can facilitate the use of explainability techniques, and (iii) as a performance byproduct, training losses are shown to converge up to 12x faster than the baseline model.

auto-encoders↗