Search NASA⌕ Search

SEARCH · Search NASA

Results for “PARTICLE MODELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Analytical model for CMB temperature angular power spectrum from cosmic (super-)strings

We present a new analytical method to calculate the small angle cosmic microwave background (CMB) temperature angular power spectrum due to cosmic (super-)string segments. In particular, using our method, we clarify the dependence on the intercommuting probability P. We find that the power spectrum is dominated by Poisson-distributed string segments. The power spectrum for a general value of P has a plateau on large angular scales and shows a power-law decrease on small angular scales. The resulting spectrum in the case of conventional cosmic strings is in very good agreement with the numerical result obtained by Fraisse et al.. Then we estimate the upper bound on the dimensionless tension of the string for various values of P by assuming that the fraction of the CMB power spectrum due to cosmic (super-)strings is less than ten percent at various angular scales up to l=2000. We find that the amplitude of the spectrum increases as the intercommuting probability. As a consequence, strings with smaller intercommuting probabilities are found to be more tightly constrained.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A Thin Lens Model for Charged-Particle RF Accelerating Gaps

Presented is a thin-lens model for an RF accelerating gap that considers general axial fields without energy dependence or other a priori assumptions. Both the cosine and sine transit time factors (i.e., Fourier transforms) are required plus two additional functions; the Hilbert transforms the transit-time factors. The combination yields a complex-valued Hamiltonian rotating in the complex plane with synchronous phase. Using Hamiltonians the phase and energy gains are computed independently in the pre-gap and post-gap regions then aligned using the asymptotic values of wave number. Derivations of these results are outlined, examples are shown, and simulations with the model are presented.

43 PARTICLE ACCELERATORS↗

Modeling Coupled Chemo-Mechanical Behavior of Randomly Oriented NMC811 Polycrystalline Li-Ion Battery Cathodes

This paper develops a three-dimensional, transient, chemo-mechanical model that predicts the performance of single secondary particle Li-ion battery cathodes. The secondary particles are composed of numerous (approximately 60) randomly oriented single-crystal primary particles. The model incorporates concentration-dependent and anisotropic material properties. As much as possible, electrochemical, transport, and structural properties for crystalline NMC811 (Li x Ni 0.8 Mn 0.1 Co 0.1 O 2 ) are taken from prior publications. Weak Van der Waals bonding between primary particles is modeled empirically using a spring analogy, which enables local primary-particle separations (disintegration) and subsequent reattachments. The model fully couples Li diffusion and the mechanical response. Results include predictions of local Li-concentrations and stresses. High stresses are found near grain boundaries, especially when the lattice orientations are greatly misaligned. Particle separations are characterized in terms of a damage parameter. The model is used to predict the effects of design and operating conditions, including charge/discharge rates, cycling scenarios, and particle sizes.

25 ENERGY STORAGE↗

Scale-dependent spatial variabilities of hydrological exchange flows and transit time in a large regulated river

Hydrological exchange flows (HEF) across the river-aquifer interface and the associated residence time of river water in the aquifer have important implications for contaminant plume migration and biogeochemical processes in the river corridor. HEFs and residence time are influenced by both subsurface physical features and hydrologic forcing related to the transport process, which can exhibit complex spatial and temporal variations. In this study, we used a massively parallel subsurface flow model and a particle-tracking model to study the influences of different control factors on spatial variability of HEFs and residence time distributions (RTD) in the Hanford Reach of the Columbia River in Washington State. A total number of 100M particles were randomly injected in time and space and then tracked in a model domain that covers a 51-km 2 area (15.1M model cells). We used hourly river stages and groundwater levels to drive the model to provide dynamic velocity fields for the particle tracking in the simulation period that was longer than 2 years. The groundwater flow simulation and particle-tracking results provide the first comprehensive assessment of the spatial distribution of HEFs and residence time in large complex river corridors. Overall, our results show that the aquifer hydrogeological structure has the strongest correlation with the extent and magnitude of exchange flux. The residence time exhibits complex patterns that are impacted by all the river geomorphologic, hydrodynamic, and hydrogeologic factors and are strongly correlated with the downwelling ratio of exchange flux. The new insights gained through this study can be used to support the development of reduced-order models of HEFs and RTDs for large complex river systems.

54 ENVIRONMENTAL SCIENCES↗

Microfield model of quasi-independent particles and nonideal plasma

An original model of a plasma microfield constructed from first principles is much more advantageous than the earlier ones. The validity of the model is confirmed by optical measurements. The thermodynamics of a gaseous plasma is qualitatively described by a new ionization equilibrium model in which the interaction between charged particles is accounted for by means of a self-consistent plasma microfield. Numerical simulations show that, in this new model, nonideal effects are insignificant even at high plasma densities, and there are no phase transitions in a gaseous plasma, a conclusion that agrees with experimental data. The model is tested against the popular models of nonideal plasma and the SESAM database.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

One-loop QCD and Higgs bosons to partons processes using six-dimensional helicity and generalized unitarity

We combine the six-dimensional helicity formalism of Cheung and O'Connell with D-dimensional generalized unitarity to obtain a new formalism for computing one-loop amplitudes in dimensionally regularized QCD. With this procedure, we simultaneously obtain the pieces that are constructible from four-dimensional unitarity cuts and the rational pieces that are missed by them, while retaining a helicity formalism. We illustrate the procedure using four- and five-point one-loop amplitudes in QCD, including examples with external fermions. We also demonstrate the technique's effectiveness in next-to-leading order QCD corrections to Higgs processes by computing the next-to-leading order correction to the Higgs plus three positive-helicity gluons amplitude in the large top-quark mass limit.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

A model for GCR-particle fluxes in stony meteorites and production rates of cosmogenic nuclides

A model is presented for the differential fluxes of galactic-cosmic-ray (GCR) particles with energies above 1 MeV inside any spherical stony meteorite as a function of the meteorite's radius and the sample's depth. This model is based on the Reedy-Arnold equations for the energy-dependent fluxes of GCR particles in the moon and is an extension of flux parameters that were derived for several meteorites of various sizes. This flux is used to calculate the production rates of many cosmogenic nuclides as a function of radius and depth. The peak production rates for most nuclides made by the reactions and energetic GCR particles occur near the centers of meteorites with radii of 40 to 70 g/cm (2). Although the model has some limitations, it reproduces well the basic trends for the depth-dependent production of cosmogenic nuclides in stony meteorites of various radii. These production profiles agree fairly well with measurments of cosmogenic nuclides in meteorites. Some of these production profiles are different than those calculated by others. The chemical dependence of the production rates for several nuclides varies with size and depth.

Reedy, R. C.↗

Multicenter Higgs oscillators and Calogero model

We show that the spherical part of N-particle Calogero model describes, after exclusion of the center of mass, the motion of the particle on (N - 2)-dimensional sphere interacting with N(N - 1)/2 force centers with Higgs oscillator potential. In the case of four-particle system these force centers are located at the vertexes of cuboctahedron. The geometry of the five-particle case is also investigated.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Coupling methods between finite element-based Boussinesq-type wave and particle-based free-surface flow models [Coupling methods between finite element-based Boussinesq-typewave and particle-based free-surface flow models]

We develop one-way coupling methods between a Boussinesq-type wave model based on the discontinuous Galerkin finite element method and a free-surface flow model based on a mesh-free particle method to strike a balance between accuracy and computational cost. In our proposed model, computation of the wave model in the global domain is conducted first, and the nonconstant velocity profiles in the vertical direction are reproduced by using its results. Computation of the free-surface flow is performed in a local domain included within the global domain with interface boundaries that move along the reproduced velocity field in a Lagrangian fashion. To represent the moving interfaces, we used a polygon wall boundary model for mesh-free particle methods. Verification and validation tests of our proposed model are performed, and results obtained by the model are compared with theoretical values and experimental results to show its accuracy and applicability.

97 MATHEMATICS AND COMPUTING↗

Dark sector searches with the CMS experiment

Astrophysical observations provide compelling evidence for gravitationally interacting dark matter in the universe that cannot be explained by the standard model of particle physics. The extraordinary amount of data from the CERN LHC presents a unique opportunity to shed light on the nature of dark matter at unprecedented collision energies. This Report comprehensively reviews the most recent searches with the CMS experiment for particles and interactions belonging to a dark sector and for dark-sector mediators. Models with invisible massive particles are probed by searches for signatures of missing transverse momentum recoiling against visible standard model particles. Searches for mediators are also conducted via fully visible final states. The results of these searches are compared with those obtained from direct-detection experiments. Searches for alternative scenarios predicting more complex dark sectors with multiple new particles and new forces are also presented. Many of these models include long-lived particles, which could manifest themselves with striking unconventional signatures with relatively small amounts of background. Searches for such particles are discussed and their impact on dark-sector scenarios is evaluated. Many results and interpretations have been newly obtained for this Report.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Detailed modeling of size distribution functions and hydrogen content in combustion-formed particles

A kinetic modeling approach is proposed to delve into the nature and chemistry of combustion-produced particles. A sectional method is used for the first time on this purpose. It is based on modeling of gas-to-particle transitions by sections containing 125 lumped species with C numbers ranging from 24 to 4 x 10{sup 8} and H/C ratio ranging from 0 to 1. This allows not only the mass evolution of particles, but also their hydrogen content to be followed. The model is tested in an atmospheric pressure premixed flat flame of ethylene/oxygen with C/O = 0.8 and cold gas flow velocity of 4 cm/s. Comparison of modeled results with experimental data is satisfying in terms of species concentrations and H/C ratio of the particles. Analysis of model results in comparison with the experimental data has shown that it is possible to distinguish different precursors of particles moving from the exit of the burner into the post-oxidation region of the flame. At particle inception, i.e. just downstream from the flame front, gas-phase PAHs are responsible for particle nucleation and oligomers of aromatic hydrocarbons and small pericondensed hydrocarbons are predominantly present. Then the dehydrogenation process takes place and soot formation starts; in this zone large pericondensed and stacked structures are produced. Further up soot maturation generally linked with dehydrogenation is present, but still a few particles with higher H/C and with low coagulation efficiency are produced and remain present along the flame. The model, in accordance with experimental structural soot analysis, shows that in soot particles condensed structures typical of clusters of large pericondensed hydrocarbons are present whereas high-molecular mass condensed species mainly comprise oligomers of small aromatic compounds of clusters of small pericondensed hydrocarbons. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Particle Dark Matter constraints: the effect of Galactic uncertainties

Collider, space, and Earth based experiments are now able to probe several extensions of the Standard Model of particle physics which provide viable dark matter candidates. Direct and indirect dark matter searches rely on inputs of astrophysical nature, such as the local dark matter density or the shape of the dark matter density profile in the target in object. The determination of these quantities is highly affected by astrophysical uncertainties. The latter, especially those for our own Galaxy, are ill-known, and often not fully accounted for when analyzing the phenomenology of particle physics models. In this paper we present a systematic, quantitative estimate of how astrophysical uncertainties on Galactic quantities (such as the local galactocentric distance, circular velocity, or the morphology of the stellar disk and bulge) propagate to the determination of the phenomenology of particle physics models, thus eventually affecting the determination of new physics parameters. We present results in the context of two specific extensions of the Standard Model (the Singlet Scalar and the Inert Doublet) that we adopt as case studies for their simplicity in illustrating the magnitude and impact of such uncertainties on the parameter space of the particle physics model itself. Our findings point toward very relevant effects of current Galactic uncertainties on the determination of particle physics parameters, and urge a systematic estimate of such uncertainties in more complex scenarios, in order to achieve constraints on the determination of new physics that realistically include all known uncertainties.

79 ASTRONOMY AND ASTROPHYSICS↗

Development and Experimental Optimization of High-Temperature Modeling Tools and Methods for Concentrated Solar Power Particle - Systems

A novel, open-source radiative modeling toolset was developed to extend the functionality of particle-based modeling software (e.g. discrete element method (DEM)) to environmental conditions relevant to concentrated solar power applications. This toolset was optimized for deployment on desktop workstations instead of high-performance computing systems, to render such tools more accessible to the research community. Both particle-based modeling and radiative exchange modeling are computationally expensive and often require specialized programming expertise, making these methods cumbersome to use. Recent developments in DEM software by DCS Computing have greatly reduced these challenges, providing a graphical-user-interface based platform and modeling optimization for desktop workstations, HPCs, and cloud computing. The University of Dayton leveraged the experience of DCS Computing in developing a user-friendly, open-source radiative heat transfer expansion for DEM modeling. The University of Dayton DEM+ radiative modeling toolset was developed using a combination of fundamental experimental measurements, modeling, and simplified flow experiments over a range of temperatures and flow conditions. The toolset provides researchers with access to multiple radiative models including an accelerated Monte-Carlo Ray Tracing (application agnostic, highly computationally expensive), an expanded database of distance-based approximations (application limited, computationally light), and a weighted blending of the two methods capable of achieving over 90% reduction in computation time with equivalent accuracy compared to Monte-Carlo Ray Tracing. Through a graphical user interface, users can customize the radiative models to match their desired accuracy and available computational resources, improving access to particle based modeling for the research community. Ceramic sintered bauxite proppants were used in modeling and experimentally as a baseline. Both the radiative heat transfer and flow properties for particulate systems were investigated at elevated temperatures up to 800 °C. The major accomplishments for this work include a verified, open-source radiative modeling toolset to be distributed amongst the research community and the fabrication of three small-scale test facilities to investigate particle behavior and tune DEM flow properties for operation up to 800 °C. The findings have been shared with the research community via conference modeling workshops, deployment of the tools in DCS Computing Aspherix®, and open-source access to the developed radiative modeling tool. The development of next-generation CSP facilities and thermal energy storage systems based on ceramic particles requires providing access to computationally efficient and accurate modeling tools. Particles will experience a wide range of environments (20-800 °C) and handling conditions (dilute curtains or dense packing), requiring specially designed and optimized equipment. Optimizing solid particle physics models and establishing best-practices for particle modeling in CSP environments will assist researchers with designing optimized equipment, accelerating the deployment of more economically-competitive CSP facilities.

14 SOLAR ENERGY↗

Three-dimensional simulations of the accretion process in Kerr space-time with arbitrary value of the spin parameter

We present the results of three-dimensional general relativistic hydrodynamic simulations of adiabatic and spherically symmetric accretion in Kerr space-time. We consider compact objects with spin parameter |a{sub *}|{<=}1 (black holes) and with |a{sub *}|>1 (superspinars). Our full three-dimensional simulations confirm the formation of equatorial outflows for high values of |a{sub *}|, as found in our previous work in 2.5 dimensions. We show that the critical value of |a{sub *}| determining the onset of powerful outflows depends mainly on the radius of the compact object. The phenomenon of equatorial outflows can hardly occur around a black hole and may thus be used to test the bound |a{sub *}|{<=}1 for astrophysical black hole candidates.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Chirality in unified theories of gravity

We show how to obtain a single chiral family of an SO(10) grand unified theory (GUT), starting from a Majorana-Weyl representation of a unifying (GraviGUT) group SO(3,11), which contains the gravitational Lorentz group SO(3,1). An action is proposed, which reduces to the correct fermionic grand unified theory action in the broken phase.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Large-scale Compression Acceleration during Magnetic Reconnection in a Low- β Plasma

In solar flares and other astrophysical systems, a major challenge for solving the particle acceleration problem associated with magnetic reconnection is the enormous scale separation between kinetic scales and the observed reconnection scale. Because of this, it has been difficult to draw any definite conclusions by just using kinetic simulations. A particle acceleration model that solves the energetic particle transport equation can capture the main acceleration physics found in kinetic simulations and thus provide a practical way to make observable predictions and directly compare model results with observations. Here we study compression particle acceleration in magnetic reconnection by solving the Parker (diffusion–advection) transport equation using velocity and magnetic fields from two-dimensional magnetohydrodynamics (MHD) simulations of a low-β high-Lundquist-number reconnection layer. We show that the compressible reconnection layer can give significant particle acceleration, leading to the formation of power-law particle energy distributions. We analyze the acceleration rate and find that the acceleration in the reconnection layer is a mixture of first- and second-order Fermi processes. When including a guide field, we find that the spectrum becomes steeper and both the power-law cutoff energy and maximum particle energy decrease as plasma becomes less compressible. This model produces a 2D particle distribution that one can use to generate a radiation map and directly compare with solar flare observations. This provides a framework to explain particle acceleration at large-scale astrophysical reconnection sites, such as solar flares.

79 ASTRONOMY AND ASTROPHYSICS↗

Advancing Multiscale Simulation of Plasma-Surface Interfaces

We report the development of an atomistic-informed, surface-state-dependent predictive model for particle exchange in a carbon-tungsten plasma-surface interface. The predictive model uses machine learning (ML) techniques to learn the energy and angular distributions for particle exchange and rate functions for surface state evolution from molecular dynamics simulations of cumulative bombardment of tungsten by energetic carbon ions. Each predictive component is sensitive to the energy and trajectory of incident plasma species and the surface state. The surface state is represented by a set of surface state descriptors, which were derived from the atomistic surface state for each independent carbon bombardment event. These descriptors are representative of the composition and degree of amorphization of the outermost angstrom of surface material and were chosen to optimize predictive performance for particle exchange at the interface. The distributions for particle exchange (reflection/sputtering) are demonstrated to vary with each surface state descriptor, motivating the development of surface-state-dependent particle exchange models for plasma simulations. The performance of various ML methods was compared, including polynomial quantile regression, artificial neural networks, k-nearest neighbors, and random forest algorithms, with polynomial regression performing the best for interpolation and extrapolation of learned relationships. In addition to the particle exchange model, a neutral network was developed and used to identify data sufficiency throughout surface descriptor space, which will enable real-time feedback during future data production to ensure data is produced where it is most needed, and we provide commentary on improvements to the data production workflow for future endeavors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗