Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shuttle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Vibration analysis of a 1/15 scale dynamic model of a space shuttle configuration

The natural frequencies and mode shapes of a 1/15 scale space shuttle dynamics model are analytically determined. The model, a parallel beam type structure with delta wings, is dynamically representative of the stiffness and mass properties of an early space shuttle design. Important characteristics of the model are elastic interfaces with adjustable spring rates. Normal mode computations are made using the finite element modeling technique as implemented in the NASTRAN (NASA Structural Analysis) computer program. The feasibility of neglecting elastic deformations in the lower modes was investigated using a rigid body model. Using NASTRAN, natural frequencies and mode shapes were first calculated for the booster fuselage, orbiter fuselage, and both delta wings in a free-free condition. Next, the fuselages were connected for various spring rates. Then the wings were attached to each fuselage, and the booster and orbiter were analyzed as separate airplanes. Finally, the two airplanes were elastically joined, and the complete model was analyzed.

Thornton, E. A.↗

Preliminary design of an auxiliary power unit for the space shuttle: Component and system configuration screening analysis

The auxiliary power unit (APU) for the space shuttle is required to provide hydraulic and electrical power on board the booster and orbiter vehicles. Five systems and their associated components, which utilize hot gas turbines to supply horsepower at gearbox output pads, were studied. Hydrogen-oxygen and storable propellants were considered for the hot gas supply. All APU's were required to be self-contained with respect to dissipating internally generated heat. These five systems were evaluated relative to a consistent criteria. The system supplied with high pressure gaseous hydrogen and oxygen was recommended as the best approach. It included a two-stage pressure-compounded partial-admission turbine, a propellant conditioning system with recuperation, a control system, and a gearbox. The gearbox output used was 240 hp. At the close of the study a 400 hp level was considered more appropriate for meeting the prime shuttle vehicle needs, and an in-depth analysis of the system at the 400 hp output level was recommended.

Binsley, R. L.↗

Space shuttle: News release

The space shuttle fact sheet is presented. Four important reasons for the program are considered to be: (1) It is the only meaningful new manned space program which can be accomplished on a modest budget. (2) It is needed to make space operations less complex and costly. (3) It is required for scientific applications in civilian and military activities. (4) It will encourage greater international participation in space flight. The space shuttle and orbiter configurations are discussed along with the missions. The scope of the study and the costs of each contract for the major contractor are listed.

Source record↗

Effects of radiation environment on reusable nuclear shuttle system

Parametric tradeoff analyses of a wide spectrum of alternate tank configurations to minimize both primary and secondary, direct and scattered radiation sources emanating from the NERVA are reported. The analytical approach utilizing point kernel techniques is described and detailed data are presented on the magnitude of neutron/gamma doses for different locations. Single-tank configurations utilizing smaller cone angles and end cap radii were found to minimize integral radiation levels, hence, stage shielding-weight penalties for shuttle missions. Hybrid configurations employing an upper tank with a reduced cone angle and end cap radius result in low integral payload doses primarily due to the increased separation distance caused by the elongation of the larger capacity upper tank. A preliminary radiation damage assessment is discussed of possible reusable nuclear shuttle materials, components, and subsystems, and the possible effects of the radiation environment on various phases of RNS mission operations.

Lane, A. G.↗

The influence of radiation shielding on reusable nuclear shuttle design

Alternate reusable nuclear shuttle configurations were synthesized and evaluated. Particular attention was given to design factors which reduced tank exposure to direct and scattered radiation, increased payload-engine separation, and improved self-shielding by the LH2 propellant. The most attractive RNS concept in terms of cost effectiveness consists of a single conical aft bulkhead tank with a high fineness ratio. Launch is accomplished by the INT-21 with the tank positioned in the inverted attitude. The NERVA engine is delivered to orbit separately where final stage assembly and checkout are accomplished. This approach is consistent with NERVA definition criteria and required operating procedures to support an economically viable nuclear shuttle transportation program in the post-1980 period.

Littman, T. M.↗

Shuttle ascent and shock impingement aerodynamic heating studies

The collection and analysis of aerodynamic heating data obtained from shock impingement experimental investigation were completed. The data were categorized into four interference areas; fin leading edge, wing/fuselage fin/plate corners, and space shuttle configurations. The effects of shock impingement were found to increase the heating rates 10 to 40 times the undisturbed values. A test program was completed at NASA/Langley Research Center to investigate the magnitudes and surface patterns of the mated shock interference flowfield. A 0.0065 scale thin-skin model of the MDAC 256-20 space shuttle booster mated with a Stycast model of the MDAC Internal tank orbiter was tested in the 20-inch M=6 tunnel, the 31-inch M=10 tunnel, and the 48-inch Unitary Plan Tunnel. The gap region of the ascent configuration was the principal area of interest where both thermocouple and phase-change paint data were obtained. Pressure and heat transfer distributions data on the leeward surface of a 75-degree sweep slab delta wing are presented. The effects of surface roughness on boundary layer transition and aerodynamic heating were investigated.

Lanning, W. D.↗

Shuttle/Agena study. Annex C: Space shuttle candidate insulator/propellant

The problem associated with the absorption of space tug propellants by the thermal insulation of the space shuttle orbiter during an emergency propellant dump was investigated. A test program was conducted to determine the compatibility of two space shuttle candidate insulation samples with earth-storable propellants. The propellant combinations used were placed in contact with the thermal insulation for two hours. Following exposure to propellants, the insulation samples were heated to 850 F for five minutes. A thermal conductivity index was determined before and after testing to evaluate possible degradation of sample chemical conductivity.

Source record↗

Shuttle program status

The status of the space shuttle phase of the space transportation system is reviewed by the use of a series of graphs and slides. Briefly described are: space shuttle capabilities and configurations; launch vehicles; mission profiles; recovery concepts; cost comparisons; program schedules; and benefits of reusable space transportation system.

Andrews, E. P.↗

A viscous starter solution for shuttle flow field computations

A time dependent numerical procedure that calculates the viscous flow in the shock layer around the shuttle nose has been developed. It has been applied to the free stream conditions that may be encountered in the shuttle flight trajectory and found to be efficient and in satisfactory agreement with other steady and unsteady techniques. Two features associated with the present formulation are responsible for its successful applications. The first is that the flow field computation is made within the shock layer; the second is that the mapping of the computational region places proportionately more mesh points in the vicinity of the wall than in the remaining computational region. The numerical results may be used for low altitude flight to determine the edge conditions for a thin boundary layer, to provide initial boundary layer profiles for downstream boundary layer calculations, and to start supersonic computations. For high altitude flight, it may be used to determine the complete flow field in the nose region and also provide a starter solution for subsequent supersonic flow computations.

Li, C. P.↗

Lee-side flow phenomena on space shuttle configurations at hypersonic speeds. Part 2: Studies of lee-surface heating at hypersonic Mach numbers

Lee surface heating data, obtained at relatively low unit Reynolds numbers at Mach 6 and 19, are discussed with emphasis on the peak heating behavior. Surface pressures measured along the lee meridian of the delta-wing orbiter are presented and analyzed in conjunction with the heating. The effects of nose bluntness and lee surface geometry on the heating are discussed and general guidelines are presented for modifying the lee surface geometry of the shuttle to reduce vortex-induced heating. The application of the wind tunnel results to realistic shuttle flight conditions is discussed.

Hefner, J. N.↗

An analysis of the booster plume impingement environment during the space shuttle nominal staging maneuver

An experimental study of the plume impingement heating on the space shuttle booster afterbody resulting from the space shuttle orbiter engine plumes was conducted. The 1/100-scale model tests consisted of one and two orbiter engine firings on a flat plate, a flat plate with a fin, and a cylinder model. The plume impingement heating rates on these surfaces were measured using thin film heat transfer gages. Results indicate the engine simulation is a reasonable approximation to the two engine configuration, but more tests are needed to verify the plume model of the main engine configuration. For impingment, results show models experienced laminar boundary layer convective heating. Therefore, tests at higher Reynolds numbers are needed to determine impingment heating.

Wojciechowski, C. J.↗

Heat-transfer testing procedures in phase B shuttle studies with emphasis on phase change data improvement

The procedures used in the application of the phase change technique to the phase B shuttle configuration are discussed along with factors which may affect data accuracy. These factors include variation of thermal properties of phase change model material, sensitivity of measured heat transfer coefficients to the assumed value of the adiabatic to total temperature ratio, and wall temperature effects. These sensitivities are illustrated in sample calculations for a shuttle geometry. Factors which may affect the visual clarity and interpretation of phase change data are discussed, and a method of improving photographic data quality through the use of polarized light is presented.

Throckmorton, D. A.↗

Aerospace transporter and lifting body activities in Europe and potential participation in the development of the space shuttle orbiter

The course of European aerospace research regarding reentry problems is briefly reviewed for the period from 1966 up to the present. The considerable experience gained by Europe, and particularly Germany, is shown to have led to their involvement and participation in the U.S. space shuttle program. The areas of investigation and expected contributions by European cooperation in the shuttle program are outlined.

Fuchs, M.↗

Vehicle performance impact on space shuttle design and concept evaluation

The continuing examination of widely varied space shuttle concepts makes an understanding of concept interaction with vehicle performance imperative. The estimation of vehicle performance is highly appurtenant to all aspects of shuttle design and hence performance has classically been a key indicator of overall concept desirability and potential. Vehicle performance assumes the added role of defining interactions between specific design characteristics, the sum total of which define a specific concept. Special attention is given to external tank effects.

Craig, M. K.↗

Optimal lifting ascent trajectories for the space shuttle

The performance gains which are possible through the use of optimal trajectories for a particular space shuttle configuration are discussed. The spacecraft configurations and aerodynamic characteristics are described. Shuttle mission payload capability is examined with respect to the optimal orbit inclination for unconstrained, constrained, and nonlifting conditions. The effects of velocity loss and heating rate on the optimal ascent trajectory are investigated.

Rau, T. R.↗

Abort separation of the shuttle

A sensitivity analysis of the factors which affect a successful abort maneuver following a space shuttle launching is presented. Wind tunnel tests were conducted using optimum simulation techniques and data acquisition procedures. Static stability, dynamic stability, and local loads were investigated. It is concluded that parallel abort separation of the space shuttle components is possible at both high and low dynamic pressures. Successful separation is dependent upon configuration, Mach number, rocket exhaust impingement and relative position and attitude of the stages.

Decker, J. P.↗

Effect of commercial and military performance requirements for transport category aircraft on space shuttle booster design and operation

The effect of two sets of performance requirements, commercial and military, on the design and operation of the space shuttle booster is evaluated. Critical thrust levels are established according to both sets of operating rules for the takeoff, cruise, and go-around flight modes, and the effect on engine requirements determined. Both flyback and ferry operations are considered. The impact of landing rules on potential shuttle flyback and ferry bases is evaluated. Factors affecting reserves are discussed, including winds, temperature, and nonstandard flight operations. Finally, a recommended set of operating rules is proposed for both flyback and ferry operations that allows adequate performance capability and safety margins without compromising design requirements for either flight phase.

Bithell, R. A.↗

Advanced Software Techniques for Data Management Systems. Volume 2: Space Shuttle Flight Executive System: Functional Design

A functional design of software executive system for the space shuttle avionics computer is presented. Three primary functions of the executive are emphasized in the design: task management, I/O management, and configuration management. The executive system organization is based on the applications software and configuration requirements established during the Phase B definition of the Space Shuttle program. Although the primary features of the executive system architecture were derived from Phase B requirements, it was specified for implementation with the IBM 4 Pi EP aerospace computer and is expected to be incorporated into a breadboard data management computer system at NASA Manned Spacecraft Center's Information system division. The executive system was structured for internal operation on the IBM 4 Pi EP system with its external configuration and applications software assumed to the characteristic of the centralized quad-redundant avionics systems defined in Phase B.

Pepe, J. T.↗