Search NASA⌕ Search

SEARCH · Search NASA

Results for “TiO2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Assessment of high temperature metallizations for I(2)L and CMOS technologies

High temperature barrier metallizations were assessed and tested for I(2)L and CMOS applications. Life tests were accelerated to 375 C in view of the -55 C to +300 C temperature range established for engine-located electronics without fuel cooling. The gold-refractory metallizations evaluated were Au-TiW-PtSi, Au-TiW/TiO2/TiW-PtSi and Au-TiW(N)-PtSi. These metallization systems were thermally annealed to at least 375 C for up to 250 hours. The critical requirement for stable diffusion barrier is the TiW grain size. Small grain (250A-500A) films were observed to be stable up to 375 C. Deposition to TiW diffusion barrier in the presence of oxygen and nitrogen also results in an effective diffusion barrier. Auger electron spectroscopy profiles of the PtSi indicates some penetration by the TiW. In the case of PtSi/TiW interface, the redistribution of oxygen further passivates the system by forming a TiO2 layer at the interface.

Christou, A.↗

High modulus invert analog glass compositions containing beryllia

Glass compositions having a Young's modulus of at least 15 million psi and a specific modulus of at least 110 million inches consisting essentially of, in mols, 10-45% SiO2, 2-15% Li2O, 3-34% BeO, 12-36% of at least one bivalent oxide selected from the group consisting of CaO, ZnO, MgO and CuO, 10-39% of at least one trivalent oxide selected from the group consisting of Al2O3, B2O3, La2O3, Y2O3 and the mixed rare earth oxides, the total number of said bivalent and trivalent oxides being at least three, and up to 10% of a tetravalent oxide selected from the group consisting of ZrO2, TiO2 and CeO2.

Bacon, J. F.↗

Non-toxic invert analog glass compositions of high modulus

Glass compositions having a Young's modulus of at least 15 million psi are described. They and a specific modulus of at least 110 million inches consist essentially of, in mols, 15 to 40% SiO2, 6 to 15% Li2O, 24 to 45% of at least two bivalent oxides selected from the group consisting of Ca, NzO, MgO and CuO; 13 to 39% of at least two trivalent oxides selected from the group consisting of Al2O3, Fe2O3, B2O3, La2O3, and Y2O3 and up to 15% of one or more tetravelent oxides selected from the group consisting of ZrO2, TiO2 and CeO2. The high modulus, low density glass compositions contain no toxic elements. The composition, glass density, Young's modulus, and specific modulus for 28 representative glasses are presented. The fiber modulus of five glasses are given.

Bacon, J. F.↗

Containerless preparation of advanced optical glasses: Experiment 77F095

Containerless processing of optical glasses was studied in preparation for space shuttle MEA flight experiments. Ground based investigation, experiment/hardware coordination activities and development of flight experiment and sample characterization plans were investigated. In the ground based investigation over 100 candidate glass materials for space processing were screened and promising compositions were identified. The system of Nb2O5-TiO2-CaO was found to be very rich with containerless glass compositions and as extensive number of the oxides combinations were tried resulting in a glass formation ternary phase diagram. The frequent occurrence of glass formation by containerless processing among the compositions for which no glass formations were previously reported indicated the possibility and an advantage of containerless processing in a terrestrial environment.

Happe, R. A.↗

Photovoltage response to temperature change at oxide semiconductor electrodes

A study has been carried out on single crystal electrodes of TiO2, SrTiO3, and alpha-Fe2O3 and polycrystalline WO3 to investigate the effect of cell temperature on the onset potential of n-type oxide semiconductor electrodes. It is found that the change of the onset potential with temperature is due to the potential change across the Helmholtz layer. The amount of this change depends on the point of zero zeta potential (pzzp) of the semiconductor electrode. The possibility of increasing the solar-to-chemical energy conversion efficiency of a photochemical cell by increasing the cell temperature is discussed.

Reichman, B.↗

A study of the photocatalytic effects of aqueous suspensions of platinized semiconductor materials on the reaction rates of candidate redox reactions

The effectiveness of powdered semiconductor materials in photocatalyzing candidate redox reactions was investigated. The rate of the photocatalyzed oxidation of cyanide at platinized TiO2 was studied. The extent of the cyanide reaction was followed directly using an electroanalytical method (i.e. differential pulse polarography). Experiments were performed in natural or artificial light. A comparison was made of kinetic data obtained for photocatalysis at platinized powders with rate data for nonplatinized powders.

Miles, A. M.↗

Ultrapure glass optical waveguide: Development in microgravity by the sol gel process

The sol-gel process for the preparation of homogeneous gels in three binary oxide systems was investigated. The glass forming ability of certain compositions in the selected oxide systems (SiO-GeO2, GeO2-PbO, and SiO2-TiO2) were studied based on their potential importance in the design of optical waveguide at longer wavelengths.

Mukherjee, S. P.↗

The Apollo 15 yellow impact glasses - Chemistry, petrology, and exotic origin

The Apollo 15 yellow impact glasses are characterized by moderate TiO2 (about 4.8%) and high abundances of the large ion lithophile elements (e.g., K, P, Hf, Th, REE). Since the chemistry of these glasses cannot be duplicated by any combination of local components presently known to occur at the Apollo 15 landing site, these yellow glasses seem to be exotic to that area. Chemical and petrologic constraints suggest that these samples were produced by impact melting of an immature mare regolith developed upon an unusual variety of mare basalt. It is speculated that the target basalts were the youngest lava flows known to exist on the moon (i.e., Eratosthenian-age lavas in Oceanus Procellarum and Mare Imbrium). Specific tests are proposed for evaluating this provocative hypothesis.

Delano, J. W.↗

Light element geochemistry and spallogenesis in lunar rocks

Abundance and isotopic compositions are measured for the very volatile elements carbon, nitrogen and sulfur in 11 lunar rocks representing a wide spectrum of textures and compositions. Samples were combusted sequentially at three temperatures in order to remove terrestrial contaminants before melting the lunar rock and liberating lunar volatiles. The combustion results indicate very little terrestrial sulfur contamination, with sulfur contents correlated with the TiO2 contents of the basalts analyzed. Sulfur isotopic compositions are remarkably uniform and similar to the Canon Diablo meteorite standard. Nitrogen levels are found to be no greater than those obtained with procedural blanks, corresponding to abundances less than 0.1 microg/g. Stable nitrogen isotope measurements indicate a spallogenic N-15 production rate of 4.1 x 10 to the -6th microg N-15/g sample/million years, in agreement with previous estimates. No indigenous carbon in excess of procedural blank levels of about 0.7 microg/g is found in lunar basalts. Levels of 1 to 5 microg/g found in highland rocks may derive from meteoritic or terrestrial sources. The average measured spallogenic C-13 production rate is 4.1 x 10 to the -6th microg C-13/g sample/million years.

Des Marais, D. J.↗

Comparison of seal materials for use in Stirling engines

In a dry, reciprocating sliding test, rods of 12 different surface materials rubbed against a glass filled PTFE gas seal. To simulate operation in a Stirling engine a gas (N2) pressure of 1 MPa differential pressure was applied across the seal. Gas leakage rates, rods surface temperatures, changes in the surface finish of the rod, surface hardness of the rod and wear rate of the seals were measured. The rod surface materials that produced the least seal were: plasma sprayed molybdenum (75 Mo 18 Ni 4 Cr), gas nitrided steel, and plasma sprayed aluminum oxide (94 Al2O3 6 TiO2). In contrast to almost all other mating surfaces, the surface roughness of the rods coated with Mo did not decrease during wear. This property is very important for the formation of a PTFE transfer film on the mating surface. The presence of a stable transfer film gives a low PTFE wear rate.

Lundholm, G.↗

History of the Apollo 15 yellow impact glass and sample 15426 and 15427

Five fragments of the Apollo yellow impact glass from breccias 15426 and 15427 have been dated by the Ar-39/Ar-40 system using a laser microprobe. These glasses were generated by impact at 3.35 + or -0.05 AE and do not confirm the prediction of 1 AE or less by Delano et al. (1982). Since these glasses were probably produced by an impact into a target of moderate-TiO2 basalts, and the only known flows of such material are younger than the impact event, the target for these glasses must be covered up by later basaltic flows. The average Ar-38-Ar-37 exposure age for these glasses is 274 + or -74 m.y.

Spangler, R. R.↗

Solar-Assisted Oxidation of Toxic Cyanide

In solar-assisted oxidation technique, oxygen-bearing air bubbled through cyanide solution in which platinized powdered TiO2 is suspended. Light from either artifical source or natural Sunlight irradiates. Experiments demonstrated this technique effective in reducing concentration of cyanide to levels well below those achieved by other methods. Results suggest effective and inexpensive method for oxidizing cyanide in industrial wastewaters.

Byvik, C. E.↗

Studies on the hot corrosion of a nickel-base superalloy, Udimet 700

The hot corrosion of a nickel-base superalloy, Udimet 700, was studied in the temperature range of 884 to 965 C and with different amounts of Na2SO4. Two different modes of degradation were identified: (1) formation of Na2MoO4 - MoO3 melt and fluxing by this melt, and (2) formation of large interconnected sulfides. The dissolution of Cr2O3, TiO2 in the Na2SO4 melt does not play a significant role in the overall corrosion process. The conditions for the formation of massive interconnected sulfides were identified and a mechanism of degradation due to sulfide formation is described. The formation of Ns2MoO4 - MoO3 melt requires an induction period and various physiochemical processes during the induction period were identified. The factors affecting the length of the induction period were also examined. The melt penetration through the oxide appears to be the prime mode of degradation whether the degradation is due to the formation of sulfides or the formation of the Na2MoO4 - MoO3 melt.

Misra, A. K.↗

Results of variable enthalpy tests of CPR-488 TIP panels in MSFC Hot Gas Facility

Tests were conducted to determine the effects of variable enthalpy levels on CPR-488 foam performance and/or recession. Also to be determined was whether the BX-250 thickness indicator plugs (TIP) concept is feasible for measuring recession rates of CPR-488 foam during external tank flight. The tests determined that the TIP plug idea works. The accuracy of the indicated recession depth is approximately + or - 1.16 in. The BX-250 plugs with TiO2 work better than the regular BX-250 plugs. Also, there is an effect of enthalpy on CPR-488 foam performance.

Dean, W. G.↗

Chemical reactions involved in the initiation of hot corrosion of IN-738

Sodium-sulfate-induced hot corrosion of preoxidized IN-738 was studied at 975 C with special emphasis placed on the processes occurring during the long induction period. Thermogravimetric tests were run for predetermined periods of time, and then one set of specimens was washed with water. Chemical analysis of the wash solutions yielded information about water soluble metal salts and residual sulfate. A second set of samples was cross sectioned dry and polished in a nonaqueous medium. Element distributions within the oxide scale were obtained from electron microprobe X-ray micrographs. Evolution of SO was monitored throughout the thermogravimetric tests. Kinetic rate studies were performed for several pertinent processes; appropriate rate constants were obtained from the following chemical reactions; Cr203 + 2 Na2S04(1) + 3/2 02 yields 2 Na2Cr04(1) + 2 S03(g)n TiO2 + Na2S04(1) yields Na20(T102)n + 503(g)n T102 + Na2Cro4(1) yields Na2(T102)n + Cr03(g).

Fryburg, G. C.↗

Selected fretting-wear-resistant coatings for Ti-6 pct Al-4 pct V alloy

The ability of several wear-resistant coatings to reduce fretting in the Ti-6Al-4V alloy is investigated. The experimental apparatus and procedures for evaluating fretting in uncoated Ti-6Al-4V alloy and in the alloy with plasma-sprayed coatings, polymer-bonded coating, and surface treatments are described. The wear volume and wear rate for the alloys are measured and compared. It is concluded that Al2O3 with 13 percent TiO2, preoxidation and nitride surface treatments, and MoS2 sputtering result in wear-resistant surfaces; however, the polyimide coating is the most wear resistant coating in both dry and moist air, and it causes the least wear to the uncoated alloy surface.

Bill, R. C.↗

Studies on the hot corrosion of a nickel-base superalloy, Udimet 700

The hot corrosion of a nickel-base superalloy, Udimet 700, was studied in the temperture range of 884 to 965 C and with different amounts of Na2SO4. Two different modes of degradation were identified: (1) formation of Na2MoO4-MoO3 melt and fluxing by this melt, and (2) formation of large interconnected sulfides. The dissolution of Cr2O3, TiO2 in the Na2SO4 melt does not play a significnt role in the overall corrosion process. The conditions for the formation of massive interconnected sulfides were identified and a mechanism of degradation due to sulfide formation is described. The formation of Na2MoO4-MoO3 melt requires an induction period and various physiochemical processes during the induction period were identified. The factors affecting the length of the induction period were also examined. The melt penetration through the oxide appears to be the prime mode of degradation whether the degradation is due to the formation of sulfides or the formation of the Na2MoO4-MoO3 melt.

Misra, A. K.↗

Practical significance and calculation of surface tension of glass, enamels and glazes

Surface tension is important in the formation of streaks in the whole procedure of enameling and glazing., in the action of TiO2 as opacifier, in the addition of borax to enamels, or metals to glasses, and in the corrosion of refractories by molten charges. By the use of known methods for measuring surface tension additive constants are found which give correct results within 1% with no discrepancy due to B2O3.

Dietzel, A.↗