Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - SWEEPBACK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Far wing depolarization of light - Generalized absorption profiles

An absorption (and/or emission) event which takes place during a strong collision is called a 'correlated event'. It is discussed how correlated events affect the far red wing depolarization of fluorescence. Attention is given to an atomic vapor which is irradiated by linearly polarized light of a frequency on the red side of the resonance line. Two limiting cases are considered, corresponding to excitation in the impact region and in the quasi-static wing. In the quasi-static wing, absorption of a photon followed by fluorescence (rather than Rayleigh scattering), occurs mostly during a collision. Correlated events dominate the scattering process. Expressions derived for the polarization of the fluorescent light are applied to far red wing depolarization. It is found that the polarization of the fluorescent light does not go to zero in the far wing, but depends crucially on the detailed nature of the anisotropy in the long-range part of the interatomic potential.

Thomann, P.↗

Aerodynamics on a transport aircraft type wing-body model

The DFLR-F4 wing-body combination is studied. The 1/38 model is formed by a 9.5 aspect ratio transonic wing and an Airbus A 310 fuselage. The F4 wing geometrical characteristics are described and the main experimental results obtained in the S2MA wind tunnel are discussed. Both wing-fuselage interferences and viscous effects, which are important on the wing due to a high rear loading, are investigated by performing 3D calculations. An attempt is made to find their limitations.

Schmitt, V.↗

Some observations of separated flow on finite wings

Wind tunnel test results for aspects of flow over airfoils exhibiting single and multiple trailing edge stall 'mushroom' cells are reported. Rectangular wings with aspect ratios of 4.0 and 9.0 were tested at Reynolds numbers of 480,000 and 257,000, respectively. Surface flow patterns were visualized by means of a fluorescent oil flow technique, separated flow was observed with a tuft wand and a water probe, spanwise flow was studied with hot-wire anemometry, smoke flow and an Ar laser illuminated the centerplane flow, and photographs were made of the oil flow patterns. Swirl patterns on partially and fully stalled wings suggested vortex flow attachments in those regions, and a saddle point on the fully stalled AR=4.0 wing indicated a secondary vortex flow at the forward region of the separation bubble. The separation wake decayed downstream, while the tip vortex interacted with the separation bubble on the fully stalled wing. Three mushroom cells were observed on the AR=9.0 wing.

Winkelmann, A. E.↗

Application of a transonic potential flow code to the static aeroelastic analysis of three-dimensional wings

A method for including elastic effects in steady, transonic wing analysis is presented. Since the aerodynamic theory is nonlinear, the method requires the coupling of two iterative processes - an aerodynamic analysis and a structural analysis. A full potential analysis code, FL022, is combined with a linear structural analysis to yield aerodynamic load distributions on and deflections of elastic wings. This method was used to analyze an aeroelastically-scaled wind tunnel model of a proposed executive-jet transport wing and an aeroelastic research wing. The results are compared with the corresponding rigid-wing analyses, and some effects of elasticity on the aerodynamic loading are noted.

Whitlow, W., Jr.↗

Chordwise and compressibility corrections for arbitrary planform slender wings

The Lomax and Sluder method for adapting slender-wing theory to delta or rectangular wings by making chordwise and compressibility corrections is extended to cover wings of any arbitrary planform in subsonic and supersonic flows. The numerical accuracy of the present work is better than that of the Lomax-Sluder results. Comparison of the results of this work with those of the vortex-lattice method and Kernel function method for a family of Gothic and arrowhead wings shows good agreement. A universal curve is proposed for the evaluation of the lift coefficient of a low aspect ratio wing of an arbitrary planform in subsonic flow. The location of the center of pressure can also be estimated.

Levin, D.↗

Dynamic load measurements with delta wings undergoing self-induced roll-oscillations

The aerodynamic forces acting on a delta wing, mounted on a free-to-roll sting-balance apparatus, were measured. Two wing planforms having leading edge sweeps of 76 and 80 deg were tested, but only the wing with the 80 deg sweep would undergo periodic self-induced roll oscillation. The time dependent forces and roll angles for this wing were then recorded for various test conditions. In these tests a considerable drop in the average normal force of the free-to-roll wing was measured, relative to the normal force obtained in the static tests. Also, the helium-bubble flow visualization technique was used to gain some insight into the periodic motion of the separated leading edge vortices.

Levin, D.↗

Wind-tunnel measurements of the chordwise pressure distribution and profile drag of a research airplane model incorporating a 17-percent-thick supercritical wing

The Langley 8-foot transonic pressure tunnel to determine the wing chordwise pressure distribution for a 0.09-scale model of a research airplane incorporating a 17-percent-thick supercritical wing. Airfoil profile drag was determined from wake pressure measurements at the 42-percent-semispan wing station. The investigation was conducted at Mach numbers from 0.30 to 0.80 over an angle-of-attack range sufficient to include buffet onset. The Reynolds number based on the mean geometric chord varied from 2 x 10 to the 6th power at Mach number 0.30 to 3.33 x 10 to the 6th power at Mach number 0.65 and was maintained at a constant value of 3.86 x 10 to the 6th power at Mach numbers from 0.70 to 0.80. Pressure coefficients for four wing semispan stations and wing-section normal-force and pitching-moment coefficients for two semispan stations are presented in tabular form over the Mach number range from 0.30 to 0.80. Plotted chordwise pressure distributions and wake profiles are given for a selected range of section normal-force coefficients over the same Mach number range.

Ferris, J. C.↗

Tabulated pressure measurements on an executive-type jet transport model with a supercritical wing

A 1/9 scale model of an existing executive type jet transport refitted with a supercritical wing was tested on in the 8 foot transonic pressure tunnel. The supercritical wing had the same sweep as the original airplane wing but had maximum thickness chord ratios 33 percent larger at the mean geometric chord and almost 50 percent larger at the wing-fuselage juncture. Wing pressure distributions and fuselage pressure distributions in the vicinity of the left nacelle were measured at Mach numbers from 0.25 to 0.90 at angles of attack that generally varied from -2 deg to 10 deg. Results are presented in tabular form without analysis.

Bartlett, D. W.↗

The NASA supercritical-wing technology

A number of high aspect ratio supercritical wings in combination with a representative wide body type fuselage were tested in the Langley 8 foot transonic pressure tunnel. The wing parameters investigated include aspect ratio, sweep, thickness to chord ratio, and camber. Subsequent to these initial series of tests, a particular wing configuration was selected for further study and development. Tests on the selected wing involved the incorporation of a larger inboard trailing edge extension, an inboard leading edge extension, and flow through nacelles. Range factors for the various supercritical wing configurations are compared with those for a reference wide body transport configuration.

Bartlett, D. W.↗

Longitudinal aerodynamic characteristics of a wing-winglet model designed at M = 0.8, C sub L = 0.4 using linear aerodynamic theory

Wind tunnel test results have been presented herein for a subsonic transport type wing fitted with winglets. Wind planform was chosen to be representative of wings used on current jet transport aircraft, while wing and winglet camber surfaces were designed using two different linear aerodynamic design methods. The purpose of the wind tunnel investigation was to determine the effectiveness of these linear aerodynamic design computer codes in designing a non-planar transport configuration which would cruise efficiently. The design lift coefficient was chosen to be 0.4, at a design Mach number of 0.8. Force and limited pressure data were obtained for the basic wing, and for the wing fitted with the two different winglet designs, at Mach numbers of 0.60, 0.70, 0.75 and 0.80 over an angle of attack range of -2 to +6 degrees, at zero sideslip. The data have been presented without analysis to expedite publication.

Kuhlman, J. M.↗

Low-speed aerodynamic characteristics of a highly swept, untwisted uncambered arrow wing

An investigation was conducted in the Langley 4- by 7-Meter Tunnel to provide a detailed study of wing pressure distributions and forces and moments acting on a highly swept arrow-wing model at low Mach numbers (0.25). A limited investigation of the effect of spoilers at several locations was also conducted. Analysis of the pressure data shows that for the configuration with undeflected leading edges, vortex separation occurs on the outboard wing panel for angles of attack on the order of only 3 deg, whereas conventional leading-edge separation occurs at a nondimensional semispan station of 0.654 for the same incidence angle. The pressure data further show that vortex separation exists at wing stations more inboard for angles of attack on the order of 7 deg and that these vortices move inboard and forward with increasing angle of attack. The force and moment data show the expected nonlinear increments in lift and pitching moment and the increased drag associated with the vortex separation. The pressure data and corresponding force and moment data confirm that deflecting the entire wing leading edge uniformly to 30 deg is effective in forestalling the onset of flow separation to angles of attack greater than 8.6 deg; however, the inboard portion of the leading edge is overdeflected. The investigation further identifies the contribution of the trailing-edge flap deflection to the leading-edge upwash fields.

Coe, P. L., Jr.↗

Numerical computation of transonic flow about wing-fuselage configurations on a vector computer

The transonic wing analysis code TWING, which uses the AF2 relaxation algorithm, has been vectorized to run on the Cray-1S computer. Vectorization of this code improved computational efficiency over that of the CDC 7600 computer by factors of 11 to 13. The improvement compares favorably with the prediction of a theoretical performance model. A convenient generalization now permits the treatment of rudimentary wing-fuselage combinations. Flow predictions for a transport configuration in both isolated-wing and wing-fuselage modes show the expected trends in shock strength and position when compared with wind-tunnel results. An isolated fighter wing is examined in terms of execution time on three different computers and in comparison with experimental data. The computational fluid dynamics code produced during this study is a careful union of an efficient three-dimensional, transonic, numerical algorithm and the vector features presently available on modern computers.

Thomas, S. D.↗

Wing extensions for improving climb performance

Recent wind tunnel studies have shown that significant improvements in wing efficiency and climb performance can be achieved using wing extensions having sharp edges and unmodified upper airfoil contours. Based on tests of six configurations, a simple tip shape provided the best wing efficiency at high lift conditions without penalty during cruise conditions. The best configuration tested exhibited more than 20 percent improvement in the maximum rate of climb, plus a reduction in stall speed and a slight improvement in cruise performance over a baseline tip with a round edge. In addition to measurements that were used to determine performance, flow visualization studies provided insight into reasons for improved wing efficiency. Tests were conducted using a high performance general aviation aircraft model with a tapered, cantilevered wing.

Nicks, O. W.↗

Effect of thrust vectoring and wing maneuver devices on transonic aeropropulsive characteristics of a supersonic fighter

The aeropropulsive characteristics of an advanced fighter designed for supersonic cruise were determined in the Langley 16-Foot Transonic Tunnel. The objectives of this investigation were to evaluate the interactive effects of thrust vectoring and wing maneuver devices on lift and drag and to determine trim characteristics. The wing maneuver devices consisted of a drooped leading edge and a trailing-edge flap. Thrust vectoring was accomplished with two dimensional (nonaxisymmetric) convergent-divergent nozzles located below the wing in two single-engine podded nacelles. A canard was utilized for trim. Thrust vector angles of 0 deg, 15 deg, and 30 deg were tested in combination with a drooped wing leading edge and with wing trailing-edge flap deflections up to 30 deg. This investigation was conducted at Mach numbers from 0.60 to 1.20, at angles of attack from 0 deg to 20 deg, and at nozzle pressure ratios from about 1 (jet off) to 10. Reynolds number based on mean aerodynamic chord varied from 9.24 x 10 to the 6th to 10.56 x 10 to the 6th.

Capone, F. J.↗

A wing concept for supersonic maneuvering

A theoretical and experimental program in which a wing concept for supersonic maneuvering was developed and then demonstrated experimentally in a series of wind tunnel tests is described. For the typical fighter wing, the problem of obtaining efficient lift at supersonic maneuvering C sub 's occurs due to development of a strong crossflow shock, and boundary layer separation. A natural means of achieving efficient supersonic maneuvering is based on controlling the non-linear inviscid crossflow on the wing in a manner analogous to the supercritical aerodynamic methods developed for transonic speeds. The application of supercritical aerodynamics to supersonic speeds is carried out using Supercritical Conical Camber (SC3). This report provides an aerodynamic analysis of the effort, with emphasis on wing design using non-linear aerodynamics. The substantial experimental data base is described in three separate wind tunnel reports, while two of the computer programs used in the work are also described in a separate report. Based on the development program it appears that a controlled supercritical crossflow can be obtained reliably on fighter-type wing planforms, with an associated drag due to lift reduction of about 20% projected using this concept.

Mason, W. H.↗

An investigation of aerodynamic characteristics of wings having vortex flow using different numerical codes

Three different numerical codes are employed to determine the aerodynamic characteristics of wings with separation induced vortex flows. Both flat as well as cambered wings of various planform shapes are studied. The effects of wing thickness, fuselage, notch ratio and multiple vortex modeling on aerodynamic performance of the wing are also examined. The theoretically predicted results are compared with experimental results to validate the various computer codes used in this study. An analytical procedure for designing aerodynamically effective leading edge extension (LEE) for a thick delta wing is also presented.

Sushil K Chaturvedi↗

Unsteady transonic aerodynamic and aeroelastic calculations about airfoils and wings

The development and application of transonic small disturbance codes for computing two dimensional flows, using the code ATRAN2, and for computing three dimensional flows, using the code ATRAN3S, are described. Calculated and experimental results are compared for unsteady flows about airfoils and wings, including several of the cases from the AGARD Standard Aeroelastic Configurations. In two dimensions, the results include AGARD priority cases for the NACA 64A006, NACA 64A010, NACA 0012, and MBB-A3 airfoils. In three dimensions, the results include flows about the F-5 wing, a typical wing, and the AGARD rectangular wings. Viscous corrections are included in some calculations, including those for the AGARD rectangular wing. For several cases, the aerodynamic and aeroelastic calculations are compared with experimental results.

Goorjian, P. M.↗

Thickness and camber effects in slender wing theory

It is noted that the flow past thin slender wings with round leading edges can remain attached up to moderate values of angle of attack. In the low aspect ratio limit, the slender wing theory of Jones (1946) can therefore provide a simple analytical tool for studying this flow. First-order corrections to slender wing theory due to spanwise thickness and camber are developed. For wings of general planform, the validity and applicability of slender wing theory have recently been extended with the addition of chordwise and compressibility corrections by Levin and Seginer (1982). It is believed that similar corrections can be applied to the present results.

Plotkin, A.↗