Search NASA⌕ Search

SEARCH · Search NASA

Results for “antenna arraying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Space vehicle thermal testing: Principles, practices and effectiveness

Component qualification and acceptance temperatures are derived from worst case thermal analyses and analytic uncertainty margin subject to certain specified temperature extremes. Temperature requirements are shown for equipment operation within specification and for survival and turn-on (need not operate within specification, but must not experience any degradation when returned to operational range). Temperature excursions for most equipment are seen to be 20 to 50 C above and below room temperature. Components without active electronics which are mounted outboard, such as solar arrays and antennas, are usually designed to withstand wider temperature excursions, particularly at the cold end. Batteries are tightly controlled at cold temperatures to increase life. Payload components such as extremely accurate clocks for precise navigation are controlled over a relatively narrow temperature range.

Gluck, Donald F.↗

The electronically steered thinned array radiometer

An L-band radiometer which allows global imaging of soil moisture from LEO is discussed. The system consists of an array of antennas with amplifiers, a device to cross-correlate the signals from the antennas, and a process to translate the resulting data into an image of brightness temperature over the field of view. The process is based on a Fourier transform relation that exists between the incident electric field strength as a function of incidence angle and electric fields across the aperture plane of the antenna. The system's image reconstruction technique and signal-to-noise performance are examined.

Ruf, C. S.↗

VLBI observations of the gravitational lens system 0957+561 - Structure and relative magnification of the A and B images

Gravitationally lensed images of the quasar 0957+561 have been observed at 13 cm wavelength using a six-antenna VLBI array with nearly milliarcsecond resolution. Models of the observed surface brightness distribution of each of the A and B images provide support of the gravitational lens hypothesis. A value of the magnitude of the relative image magnification A/B of 0.64 + or - 0.03 is obtained.

Gorenstein, M. V.↗

The 30-GHz monolithic receive module

The fourth year progress is described on a program to develop a 27.5 to 30 GHz GaAs monolithic receive module for spaceborne-communication antenna feed array applications, and to deliver submodules for experimental evaluation. Program goals include an overall receive module noise figure of 5 dB, a 30 dB RF to IF gain with six levels of intermediate gain control, a five bit phase shifter, and a maximum power consumption of 250 mW. Submicron gate length single and dual gate FETs are described and applied in the development of monolithic gain control amplifiers and low noise amplifiers. A two-stage monolithic gain control amplifier based on ion implanted dual gate MESFETs was designed and fabricated. The gain control amplifier has a gain of 12 dB at 29 GHz with a gain control range of over 13 dB. A two-stage monolithic low noise amplifier based on ion implanted MESFETs which provides 7 dB gain with 6.2 dB noise figure at 29 GHz was also developed. An interconnected receive module containing LNA, gain control, and phase shifter submodules was built using the LNA and gain control ICs as well as a monolithic phase shifter developed previously under this program. The design, fabrication, and evaluation of this interconnected receiver is presented. Progress in the development of an RF/IF submodule containing a unique ion implanted diode mixer diode and a broadband balanced mixer monolithic IC with on-chip IF amplifier and the initial design of circuits for the RF portion of a two submodule receiver are also discussed.

Bauhahn, P.↗

Advanced propulsion for LEO and GEO platforms

Mission requirements and mass savings applicable to specific low earth orbit and geostationary earth orbit platforms using three highly developed propulsion systems are described. Advanced hypergolic bipropellant thrusters and hydrazine arcjets can provide about 11 percent additional instrument payload to 14,000 kg LEO platforms. By using electric propulsion on a 8,000 kg class GEO platform, mass savings in excess of 15 percent of the beginning-of-life platform mass are obtained. Effects of large, advanced technology solar arrays and antennas on platform propulsion requirements are also discussed.

Sovey, James S.↗

Advanced propulsion for LEO and GEO platforms

Mission requirements and mass savings applicable to specific low earth orbit and geostationary earth orbit platforms using three highly developed propulsion systems are described. Advanced hypergolic bipropellant thrusters and hydrazine arcjets can provide about 11 percent additional instrument payload to 14,000 kg LEO platforms. By using electric propulsion on a 8,000 kg class GEO platform, mass savings in excess of 15 percent of the beginning-of-life platform mass are obtained. Effects of large, advanced technology solar arrays and antennas on platform propulsion requirements are also discussed.

Sovey, James S.↗

Electromagnetic characterization of conformal antennas

The ultimate objective of this project is to develop a new technique which permits an accurate simulation of microstrip patch antennas or arrays with various feed, superstrate and/or substrate configurations residing in a recessed cavity whose aperture is planar, cylindrical or otherwise conformed to the substructure. The technique combines the finite element and boundary integral methods to formulate a system suitable for solution via the conjugate gradient method in conjunction with the fast Fourier transform. The final code is intended to compute both scattering and radiation patterns of the structure with an affordable memory demand. With upgraded capabilities, the four included papers examined the radar cross section (RCS), input impedance, gain, and resonant frequency of several rectangular configurations using different loading and substrate/superstrate configurations.

Volakis, John L.↗

Analysis of rotationally symmetric arrays of apertures on conducting spherical surfaces

Rotationally symmetric arrays of circular waveguide fed apertures on conducting spherical surfaces have been analyzed. Representation of the outside electromagnetic fields in terms of spherical transmission line modes permit the array analysis to be viewed as a spherical waveguide junction discontinuity problem. The apertures, in general, carry dual polarized circular waveguide TE11 modes. Two independent formulations - the unit cell method and the eigenexcitation method that take rotational symmetry into account - are developed and are checked against each other numerically for computational accuracy. These two formulations are analytically linked as discrete Fourier series pairs. It is seen that mutual coupling along the array decays more rapidly when the polarization of excitation is perpendicular to the array plane than when it is parallel to it. This analysis has been applied in the performance analysis of the Dome Lens phased array radar antenna.

Bondyopadhyay, Probir K.↗

Thermal elastic shock and its effect on TOPEX spacecraft attitude control

Thermal elastic shock (TES) is a twice per orbit impulsive disturbance torque experienced by low-Earth orbiting spacecraft. The fundamental equations used to model the TES disturbance torque for typical spacecraft appendages (e.g., solar arrays and antenna booms) are derived in detail. In particular, the attitude-pointing performance of the TOPEX spacecraft, when subjected to the TES disturbance, is analyzed using a three-axis nonlinear time-domain simulation. Results indicate that the TOPEX spacecraft could exceed its roll-axis attitude-control requirement during penumbral transitions, and remain in violation for approximately 150 sec each orbit until the umbra collapses. A localized active-control system is proposed as a solution to minimize and/or eliminate the degrading effects of the TES disturbance.

Zimbelman, Darrell F.↗

Double-Square-Loop Triband Frequency-Selective Microwave Reflector

Double-square-loop antenna elements arrayed on dielectric panel. Dichroic microwave reflector consisting of planar square array of double-square-loop copper elements on thin sheet of Kapton (or equivalent) polyimide supported by Kevlar (or equivalent) aromatic polyamid honeycomb sandwich panel. Array and panel designed to reflect most of incident electromagnetic radiation of frequencies between 7.2 and 8.4 GHz (in X band) and to transmit most of that at 2.3 GHz (in S Band) and 13.8 GHz {in K(sub u) band}.

Wu, Te-Kao↗

Broadband Uniplanar Microstrip to Slot-Line Transitions

New in line uniplanar microstrip-to-slotline transitions for MIC/MMIC and phased array slotline antenna applications are described. Such transactions are compact and suitable to be used in an open environment or inside a package or a multichip module. The transitions share the concept of using a balun which consists of two microstrip lines connected to a slotline through a pair of coupled microstrips. The transitions are studied theoretically using the finite difference time domain (FDTD) technique and measured experimentally using an HP8510C Network Analyzer. For a back-to-back configuration, an insertion loss of less than 1.3 dB per transition is achieved over a 40% 3-dB bandwidth with a minimum of 0.6 dB at the design frequency.

Dib, Nihad I.↗

Non-explosive actuation for the ORBCOMM (TM) satellite

Spool-based non-explosive actuator (NEA) devices are used for three important holddown and release functions during the establishment of the ORBCOMM (TM) constellation. Non-explosive separation nuts are used to restrain and release the 26 individual satellites into low earth orbit. Cable release mechanisms based on the same technology are used to release the solar arrays and antenna boom.

Robinson, Anthony↗

Miocrowave spectral imaging, H-alpha and hard X-ray observations of a solar limb flare

We compare the microwave, H-alpha, and hard X-ray observations for a west limb C7.3 flare that occurred at 17:10 UT, 1992 June 26. H-alpha movies were obtained at Big Bear Solar Observatory. Before the onset of the flare, overexposed H-alpha images show the complicated flux loop structure above the limb. Material was observed to descend along the loops toward the site where the flare occurred hours later. Using the five-antenna solar array at Owens Valley Radio Observatory, we obtain two-dimensional maps of flare emission from 1.4 to 14 GHz. In all three temporal peaks of the microwave bursts, the maps show the same characteristics. The peak low-frequency emission comes from the top of one bundle of the H-alpha loops and gradually shifts to the foot-point of the loops (the location of H-alpha flare) as the frequency increases. The location of the emission peak shifts 88 sec between 1 and 14 GHz. Seventy percent of the shift occurs between 1 and 5 GHz. The locus of the shift of the emission peak follows the shape of an H-alpha surge that occurred after the flare. For each point along the locus, we create the microwave brightness temperature spectrum and compare the radio-derived electron distribution with that derived from the high-resolution hard X-ray spectra measured with Burst and Transient Source Experiment (BATSE) on board the Compton Gamma Ray Observatory (CGRO). We find that the peak frequency changes from approximately 3 GHz at the loop top to approximately 7 GHz at the footprint, presumably due to the increase of the magnetic field from approximately 160 GHz at the loop top to approximately 300 G at the footpoint. The high-frequency slope of the microwave power-law spectrum decreases from approximately 10 at the loop top to approximately 5 at the footprint due to a change in the energy distribution of the dominant electrons. The microwave brightness temperature spectral index predicted by the BATSE power-law hard X-ray spectra agrees with the measured value only at the footpoint. At the loop top, the emission may be thermal gyrosynchrotron with a temperature of 3.5 x 10(exp 7) K, which is likely to correspond to the superhot component seen in the hard X-ray emission.

Wang, H.↗

Balloon-Borne Observations of the Polarization of the Cosmic Microwave Background

This final report is confined to the sub-contract to Caltech, and does not cover work at the PI institution (PI John Ruhl, Case Western Reserve University). In our original proposal, we planned to fly BOOMERANG twice, in the 2000 / 2001 and 2002 / 2003 Austral LDB seasons. The first flight was to have used a newly developed detector technology: the Polarization Sensitive Bolometer (PSB). The second flight was to have used a yet more sophisticated technology: a polarization sensitive, antenna-coupled array (CAMWA). The development of both technologies proceeded more slowly than anticipated. In the end, we were successful in developing the PSB technology to maturity, integrating it into the payload, and flying the payload once during the 2002/2003 Austral season. The payload performed well during this flight, and analysis of the data is in progress. As originally proposed, we have also continued to work on analysis of the data from the 1998 flight, and several publications have resulted. Sufficient progress has been made on the CAMWA technology that we expect to be able to field it into an instrument in 2 to 3 years. However, ground-based telescopes now appear to be a more attractive platform for CMB polarimetry, owing to the longer integration times available. We thus anticipate first implementing CAMWA on a ground-based telescope at South Pole.

Source record↗

The Wettability of LaRC Colorless Polyimide Resins on Casting Surfaces

Two colorless polyimides developed at NASA Langley Research Center, LaRC -CP1 and LaRC -CP2, are noted for being optically transparent, resistant to radiation, and soluble in the imide form. These materials may be used to make transparent, thin polymer films for building large space reflector/collector inflatable antennas, solar arrays, radiometers, etc. Structures such as these require large area, seamless films produced via spin casting or spray coating the soluble imide on a variety of substrates. The ability of the soluble imide to wet and spread over the mandrel or casting substrate is needed information for processing these structures with minimum waste and reprocessing, thereby, reducing the production costs. The wettability of a liquid is reported as the contact angle of the solid/liquid system. This fairly simple measurement is complicated by the porosity and the amount of contamination of the solid substrate. This work investigates the effect of inherent viscosity, concentration of polyimide solids, and solvent type on the wettability of various curing surfaces.

Miner, Gilda A.↗

On the Fringe Field of Wide Angle LC Optical Phased Array

For free space laser communication, light weighted large deployable optics is a critical component for the transmitter. However, such an optical element will introduce large aberrations due to the fact that the surface figure of the large optics is susceptable to deformation in the space environment. We propose to use a high-resolution liquid crystal spatial light modulator to correct for wavefront aberrations introduced by the primary optical element, and to achieve very fine beam steering and shaping at the same time. A 2-D optical phased array (OPA) antenna based on a Liquid Crystal on Silicon (LCOS) spatial light modulator is described. This device offers a combination of low cost, high resolution, high accuracy, high diffraction efficiency at video speed. To quantitatively understand the influence factor of the different design parameters, a computer simulation of the device is given by the 2-D director simulation and the Finite Difference Time domain (FDTD) simulation. For the 1-D OPA, we define the maximum steering angle to have a grating period of 8 pixel/reset scheme; as for larger steering angles than this criterion, the diffraction efficiency drops dramatically. In this case, the diffraction efficiency of 0.86 and the Strehl ratio of 0.9 are obtained in the simulation. The performance of the device in achieving high resolution wavefront correction and beam steering is also characterized experimentally.

Wang, Xighua↗

Laser Beam Steering/shaping for Free Space Optical Communication

The 2-D Optical Phased Array (OPA) antenna based on a Liquid Crystal On Silicon (LCoS) device can be considered for use in free space optical communication as an active beam controlling device. Several examples of the functionality of the device include: beam steering in the horizontal and elevation direction; high resolution wavefront compensation in a large telescope; and beam shaping with the computer generated kinoform. Various issues related to the diffraction efficiency, steering range, steering accuracy as well as the magnitude of wavefront compensation are discussed.

Wang, Xinghua↗

Mechanical and Electrical Properties of a Polyimide Film Significantly Enhanced by the Addition of Single-Wall Carbon Nanotubes

Single-wall carbon nanotubes have been shown to possess a combination of outstanding mechanical, electrical, and thermal properties. The use of carbon nanotubes as an additive to improve the mechanical properties of polymers and/or enhance their thermal and electrical conductivity has been a topic of intense interest. Nanotube-modified polymeric materials could find a variety of applications in NASA missions including large-area antennas, solar arrays, and solar sails; radiation shielding materials for vehicles, habitats, and extravehicular activity suits; and multifunctional materials for vehicle structures and habitats. Use of these revolutionary materials could reduce vehicle weight significantly and improve vehicle performance and capabilities.

Meador, Michael A.↗